Search Documents

Forty-three years ago a record for low cost was made at the Spanish mine, in Nevada county, California. In 22 days of September, 1887, there was mined 2796 tons of ore at a cost of 37.5 cents per ton, of which 32.4 cents was for labor and 5.1 cents for supplies. The mill treated this ore for 23 cents per ton, of which 12.3 cents was for labor and 10.7 cents for supplies. Thus the total operating cost was 60.5 cents per ton. The yield was $1.16 in gold per ton, leaving a profit of 56 cents per ton, or 48 per cent of the yield. The mine was an open-cut in a schist formation on a hillside and the work was done by Chinese laborers that were paid $1.40 per shift. The ore was soft, and could be ground effectively in four Hunting- ton mills, supplemented by silvered amalgamating plates.* The engineer in charge was F. W. Bradley, a student from the University of California. As has been indicated, the conditions were unusually favorable in respect of softness of ore, accessibility to the mill, metallurgic simplicity, with cheap labor and power, but even at that the results were so remark- able as to attract general attention, which, as might be expected, was magnified, for advertising purposes, by the manufacturers of the Huntington mill, the firm of Parke & Lacy, at San Francisco. The record made at the Spanish mine therefore found its way into many textbooks on mining published at that time. The editor of the 'Mining and Scientific Press'† (at that date, Charles G. Yale) evidently took a warm interest in. the

Jan 1, 1932

By J. W. Taylor, E. G. Zukas

THE results of shock-loading studies on copper were reported several years ago by smith. In his experiments, Smith found that there was a correlation between the shock direction and the orientation of twins which the shock produced. By using free-surface-type shots in which the free surface of the specimen was not normal to the shock direction, he showed conclusively that twinning of copper in impulsive loading was caused by the rarefaction wave. Similar tests with iron, however, showed that it twinned during compression. More recent studies of iron2 and on Fe-Si single crystals3 have shown that twinning can be suppressed in these materials by shock loading at pressures high enough so that the velocity of the shock wave exceeds the elastic-wave velocity. From these observations, it appeared that twinning was caused by the shear stresses present in the zone undergoing adjustment from one-dimensional to three-dimensional loading. At high pressures, such a zone becomes so thin that there is insufficient time for the relatively ordered motion of atoms involved in twinning to occur. Twinning in copper, therefore, cannot be produced by a single compressive shock wave because resolved shear stress large enough to create twins exists only for a very short time (0.01 psec or less) before the pressure increases suddenly and loading becomes essentially hydrostatic. (A typical pressure vs time record for a copper shot, illustrating the short rise time of the compression wave, is shown in Fig. 1.) If, on the other hand, a second shock wave can be created in a precompressed sample, then the new elastic limit is several kilobars,4 and a resolved shear stress sufficient to cause twinning should be maintained for an adequate time period (0.1 psec or more). This experimental situation can, in fact, be realized. The experimental arrangement used to do so is shown in Fig. 2. By utilizing the pressure transformation in Fe-V alloys, it was possible to shock-load the copper in compression while the copper was already precompressed. In the first test, an 8 wt pct V-Fe sample was used as a driver for loading the copper, and the copper was exposed to the following series of compressive shocks: 1) an elastic wave of about 8 kbars, which is usually ignored in shock studies; 2) the pressure transformation wave for the driver of 200 kbars; and 3) the driving shock wave of 270 kbars pressure. Metallurgical determination of the angular twin distribution, shown in Fig. 3, with respect to the shock direction and the shock rarefaction direction (which was 23 deg from the shock direction) showed that twinning took place

Jan 1, 1965

By H. J. Wasson

At the close of 1927 Venezuela was producing at the rate of 205,000 bbl, per day, making it the third country in the world in point of present daily production. For the year, the total was close to 64,000,000 bbl., representing an increase of about 70 per cent. over the 37,000,000 bbl. in round numbers produced in 1926. All of the 1927 production canie from fields opened up before the beginning of the year. While no new fields were added to the list of shippers, the past 12 months' wildcatting yielded a fair quota of new discoveries which, in the light of prcsent results, may be considered likely sources of production in due time. Altogether three such promising finds were made Of first importance, at least for the immediate future, is the completion by the Lago Petroleum Corpn. of the San Matins well, 4 miles north of the present edge of the Lagunillas field. Although rated as only a 125. bbl. well, at 3217 ft., it indicates a probable extension of the field over the intervening 4 miles between the two. The two other wildcat discoveries of importance were the Los Manueles well in the District of Colon, which has in all probability opened up a new field about 7 miles north of the present Tarra oprations; and the Honibre Pintado well of the Standard Oil Co. of Venezuela,. in the State of Falcon, which is considered to be a promising clc~vc~lop~ncnt. Neither of these last mentioned two discoveries will apprcciably affect production during 1928, as the Manueles area must await the carrying out of a general plan for the exploitation of the District of Colon, a problem requiring time. The Hombre Pintado area is being tested further, but doubtless several wells will be put down before. anything definite will be done towards making the pipe line. arrangements that rnust necessarily precede the commercial exploitation of the field. The San Matias Well The San Matias well is a highly significant dcvelopment,. It is located along the trend of the La Rosa-Ilagunillas producing formations, and when drilling started, production in the Lagunillas field was 4 miles

Jan 1, 1928

By Donald J. Worth

INTRODUCTION Minera Real de Angeles makes a very interesting case study in more ways than one. To begin with, it represents the first time a bulk silver deposit has been put into production in Mexico. Second, the feasibility and financing stage spanned a period when the silver price ranged from $4 to $40 per ounce. Third, there was a major devaluation of the peso and a financial crisis in Mexico at completion of the project. Fourth, the composition of the partnership (a major Canadian mining company, a major Mexican mining company and the host government's own mining entity) is worthy of note. This paper gives considerable background on the project and how it came to fruition. The political risk aspects and how the major provider of funds perceived Mexican risk at the time of decision to participate and afterwards are highlighted. LOCATION AND HISTORY The Real de Angeles deposit is located at an elevation of 2300 meters in Central Mexico in the State of Zacatecas (Figure 1). The closest village is Noria de Angeles, three kilometers to the north. The closest cities are Aguascalientes, Zacatecas and San Luis Potosi. The first-mentioned is one hour to the southwest by automobile over good roads. Exploitation of the vein outcrops probably began towards the end of the sixteenth century by the Spanish. Evidence of past mining activity is shown by numerous shafts, manways, dumps and ruins. Also, there were remnants of two rudimentary concentrating mills now obliterated by pit development and in the nearby town of Noria de Angeles the ruins of a small smelter still exist. Compania Minera Gamma, an affiliate of a major international mining company, investigated Real de Angeles from 1969 to 1971. Its evaluation program included 20 drill holes and comprehensive geological engineering and metallurgical studies. The results were not encouraging and the option on the property was dropped. In late August 1973 geologists representing Placer Mexicana which was later renamed Explomin were advised of the availability of the property and liked the prospects sufficiently to make an option payment soon due and to agree to outright purchase by year-end. A series of 34 holes were drilled by Explomin and a preliminary study indicated that the prospect had mine-making potential if the silver price was right. [ ] DESCRIPTION OF THE PROJECT Real de Angeles is best described as a large, low grade open pit silver mine because at today's prices approximately 70% of the realizable revenue is derived from that metal. One must also keep in mind that the operation produces two concentrates - a lead concentrate with high silver content and

Jan 1, 1985

By G. A. Bole, F. W. Davis

The purpose of this paper is not to report, to the Institute, the results so far obtained in the survey, by the Bureau of Mines, of the metallurgical requirements for open-hearth refractories, but to present an outline that we hope will serve as a basis for discussion. The systematic survey that the Bureau proposes to make has not been outlined, although considerable preliminary work has been done in the way of interviewing open-hearth superintendents in several of the larger steel plants from the Chicago district eastward. At the several conferences so many of the opinions were diametrically oppoeite, when considering the same point, that it was thought that such an opportunity as the Institute offers in the way of a clearing house for moot metallurgical topics should not be overlooked. For this reason, the paper has been prepared as a basis for a discussion which, it is believed, will be of value in outlining the program of the Bureau. D. A. LYoN, Assistant Director. The importance of securing suitable refractories for metallurgical operations is daily becoming more universally recognized; particularly in the manufacture of open-hearth steel, where the life and earning power of the furnace depends largely on the judgment and care exercised in the selection of the correct quality of refractory for each of the parts. Any innovation that would make available to the steel manufacturers refractories with longer life or better suited to their needs than those now employed, and at a cost that would permit of their use, would be of enormous value to the industry at large. It is quite probable that revolutionary changes would not be necessary. Material now used in some parts of the furnace might, by more suitable preparation, be made of much greater service; in other parts, possibly entirely different material would be necessary in order to effect much improvement. Inasmuch as different parts of the furnace structure perform different functions and are subjected to different service conditions, a refractory suitable for one part will be entirely unsuited for another. For this reason, to make a comprehensive study of the refractory requirements of the processes, we should consider the furnace as built up of a number

Jan 1, 1924

By F. G. Miller

The washabilities of typical bituminous coals are discussed in an effort to illustrate the importance of determining, by a complete washability study, the sulfur forms and their distribution in a coal. This study will then show the extent to which the sulfur can be removed. It should be emphasized that each potential application requires a thorough study because of the varying amounts of sulfur in different coals. It is not the intent of this paper to show the best results that flotation can produce, but rather to illustrate the potential of this process and point out the importance of improved flotation techniques where sulfur reduction is involved. It is generally accepted that sulfur exists in coal in three forms: (1) pyritic, (2) organic, and (3) sulfate sulfur. Sulfate sulfur usually makes up less than 1% of the total sulfur content. Pyritic and organic sulfur make up almost all of the total sulfur content, occur in varying amounts in different coals, and can vary greatly in coal of the same seam. Pyritic sulfurs of 20% to 80% of the total sulfur have been reported. Other authors have shown that it is not possible to remove the organic sulfur without chemically altering the coal. Chapman and ones' state: "Organic sulfur, unlike pyritic sulfur does not exist as discrete particles, but is intimately associated with the coal structure, and as such it is not possible to remove it or reduce its concentration by physical means." Any success in removing sulfur has come about by removing pyritic sulfur by physical means; therefore, removal of sulfur in the pyritic form is the subject of this investigation. The extent to which any impurities can be removed from a particular coal can be determined by a washability study. Outside of crushing coal to finer sizes or chemically altering the coal, there are no known methods of changing this inherent washability characteristic. The efficiency of various methods used to remove impurities can be determined by comparison of results produced at a yield to the results as shown by a washability study. In recent years heavy media processes have proven their ability to wash plus 28 mesh coal and nearly produce results shown to be theoretically possible by the washability study. Therefore, it is the objective of this paper to show various methods of treating the finer fractions of the coal, in the hope of developing

Jan 1, 1964

By Vsevolod Krivobok

IT is generally recognized that "low temperatures" have a definite effect on the properties of metals and alloys. Furthermore, it is also generally understood that the effect is decidedly adverse. The possibility that the same low-temperature treatment might be employed for the purpose of improving certain properties of the .alloys has received less attention until recently, and the experimental and theoretical knowledge consequently is meager. The effect of low temperatures may be studied in two ways: by studying such properties as tensile strength, hardness, impact resistance, etc., at low temperature, and by studying the properties of alloys at room temperature after these alloys have been subjected to a low-temperature treatment. Even in the latter case, certain properties will differ materially from the same properties obtained on identical material but without cold treatment. In other words, subjecting alloys to cold treatment results in an irreversible change in mechanical properties. Changes of this character are usually indications of the appearance of a new phase or phases, and would be likely to occur in alloys which, either by virtue of their composition or by heat treatment, are retained at room temperature in a metastable condition. Consequently, studies of the effect of low temperatures logically should be conducted from the physicochemical point of view, since the results of such studies not only would furnish metallurgists with interesting theoretical data but would clearly indicate the classes of alloys that would hold promise of improvement, and, possibly, of new applications. As the present investigation deals with chromium and chromium-nickel alloys of iron of the stainless variety, it has been thought desirable to present the data concerning low-temperature properties of these alloys, available from the most recent and most comprehensive work of H: S. Russell.' A summary, of these data is given in Table 1. The data are confined to a limited number of alloys of the type dealt with in the present

Jan 1, 1931

By J. R. Long, T. R. Graham, R. S. Dean

ALTHOUGH considerable information has been published concerning manganese additions to the aluminum bronzes, these data refer principally to the two-phase alloys containing 8 to 11 pct aluminum, with some incidental information on the single-phase alpha solid solution alloys. Strauss1 gives an excellent review of the literature on aluminum bronzes up to 1927 and a bulletin2 of the Copper Development Association brings the bibliography up to 1938. The most extensive work on manganese addition is that of Rosenhain and Lantsberry,3 who investigated alloys ranging up to 10 pct aluminum and up to 10 pct manganese, and presented data on the physical properties of sand-cast, chill-cast, and several wrought alloys. The greater portion of the work, however, concerns alloys ranging from 7 to 10 pct aluminum in the cast condition and sheds little light on the properties of wrought single-phase alloys. Corson4 notes that alloys containing 10 pct manganese and 4 pct aluminum are not hardenable by heat-treatment, while one with 15 pct manganese and 5 pct aluminum can be hardened, but he gives no tensile data on it. In fact, no systematic study of the properties of single-phase wrought alloys containing substantial amounts of manganese has been reported. It should also be noted that most of the investigators worked with alloys containing significant amounts of iron and silicon, and that these impurities, whether intentionally added or accrued from the raw materials used in the preparation of the alloys, may be expected to have a direct bearing on the resultant properties. In the work on alloys made with electrolytic manganese, the Bureau of Mines has undertaken an investigation of the copper-manganese-aluminum system for the purpose of establishing the constitution and properties of high-purity alloys. In a recent paper5 the authors reported a metallographic investigation of the alpha solid solution area and the adjoining fields of the copper-manganese-aluminum system up to 50 pct manganese. This study established the alpha-phase boundaries at 50° temperature levels from 400° to 850°C. It was found that the addition of manganese to copper-aluminum alloys decreases the solubility of aluminum in the alpha phase (Fig I), curving the boundary toward the copper-manganese base line. The greatest change occurs in the first 20 to 25 pct manganese, which decreases the solubility of aluminum to approximately 4 pct. With larger amounts of manganese the alpha boundary tends to parallel the copper-manganese binary. At 1300°F and higher,

Jan 1, 1947

By E. J. Duggan

THE mine and mill of the Climax Molybdenum Co. are at Climax, Colorado. Climax is on Fremont pass directly on the Continental Divide, at an elevation of 11,400 feet. DESCRIPTION OF ORE The Climax ore-bearing rock is essentially an altered and highly silicified granite, fully half of the gangue being quartz. Molybdenite is the only mineral of economic consequence and most of it is intimately associated with quartz in the form of fine veinlets and stringers. Other minerals are molybdite, pyrite, and chalcopyrite. While the molybdite may be readily extracted by hydrometallurgical methods, its content is too low to make such operations profitable. The pyrite content ranges from 2 to 5 per cent and that of the chalcopyrite from 0.03 to 0.05 per cent. There is not enough copper to make its recovery attractive and one of the metallurgical problems is the elimination of it and the pyrite from the product. On account of the close association of the molybdenite with the quartz and the necessity of eliminating the pyrite and chalcopyrite from the final product, fine grinding followed by flotation is the only feasible method of concentration. HISTORY Construction of the first milling unit was started in 1017 and it was operated during parts of 1918 and 1910. In the postwar years, there was almost no demand for the product and production was at a standstill until 1024. The Company's research campaign to develop the use of the metal began to show results in that year. From 1926 to 1932 production ranged from 500 to 1200 tons per day. In 1931 an additional mill section was built and production was gradually increased until in 1934 and 1935 about 3000 to 4000 tons was milled per day. This tonnage overtaxed the milling facilities, and as the demand for molybdenum was growing constantly, additional milling equipment was needed. In 1936 and 1937 another crushing plant, six additional mill sections and the necessary auxiliary plants were constructed and brought into operation. This plant was designed to mill I0,000 tons per day, but it was not long before 12,500 tons was being treated during periods of peak demands. During the summer of 1941, to meet defense needs, the mill has been required to treat 15,500 tons per day. This has been accomplished with little plant expansion and at no loss in recovery, as will be described later. To increase capacity still further, one more primary section is now being built. This will bring capacity to 18,000 tons per day, which can be stretched to 20,000 tons at a small sacrifice in recovery. CRUSHING There are two crushing plants: No. I, of 5000 tons capacity (flowsheet in Fig. I) and No. 2, of 15,000 tons capacity (Fig. 2).

Jan 1, 1942

By Russell A. Carter

Alaska is a land of immense proportions and resources. Its very name, derived from an Aleut term, means "The Great Land." Yet, in a state slightly larger than Texas, California, and Montana combined, there are presently only two-large scale mines in production, excluding dredge operations. Once referred to by its territorial governor as "a storehouse of minerals," Alaska is, in the opinion of many industry observers, at least 20 years away from a healthy, productive mining industry. The mineral potential of the state is tremendous: coal deposits on the North Slope alone have been hypothetically pegged at 1.5 trillion tons. Copper-zinc deposits on the south flank of the Brooks Range are conservatively estimated to be worth $4 billion to $6 billion. However, the problems facing mineral development are of equal magnitude, and include:

Jan 11, 1976

E. E. Russell Tratman, New York City (communication to the Secretary): Mr. Glenn's paper brings up again the question of the part played by coal-dust in colliery-explosions. In the discussion of Sir Frederick Abel's paper on " Accidents in Mines," read before the Institution of Civil Engineers,? much was said about the dangerous properties of coal-dust, and several instances were given of the successful use of a spray of water, water and compressed air, or exhaust-steam from an engine, to keep the mine SUEciently damp to prevent the formation of dust clouds. Methods of preventing shots from blowing out; of using water cartridges to prevent flame ; and of using lime cartridges, wedges and other means of breaking down the coal were also discussed. Mr. Emerson Bainbridge referred to the explosive termed " roburite " (ammonium nitrate and

Jan 1, 1895

By B. W. Gonser, C. M. Heath

The importance of grain size and its control in wrought brass needs no lengthy discussion, since specifications so often make exact control imperative. Aids to this control are therefore of interest. The effect of a number of different elements on the grain growth of brass under various conditions of annealing has been reported in the technical literature. In particular, a paper by Cook and Miller1 a few years ago, with the discussion that followed, gave valuable information on the effects of iron, phosphorus, manganese, aluminum, aluminum plus nickel, and aluminum plus silicon. Price12 in his discussion of that paper, added a description of some commercial brasses that exhibited a grain-refining effect owing to the presence of 2 per cent A1 and 1 per cent Ni. Gibson and Doss3 have recently given data on the effect of iron on annealing high brass. No comprehensive study, however, has been given to the effect of additions of chromium. It has been the purpose of this investigation to determine the effect of adding various amounts of chromium to a plain cartridge brass, particularly in regard to the effect on grain growth in various annealing treatments after cold-working. Prepakation of Alloys Alloys of high-purity brass of 68.5 Cu, 31.5 Zn composition were made containing from 0 to 0.17 per cent Cr. These were produced in induction furnaces, using unlined graphite crucibles to hold the charge. The melts were cast into rectangular chill molds giving ingots about % by 3 by 10 in. in size.

Jan 1, 1938

By George F. Comstock

It has been reported recently1 that the hardenability and toughness of forging steels may be improved appreciably by the use of complex deoxidizers containing titanium, aluminum, and vanadium. In the light of these results, an investigation of similar deoxidizers containing various hardening and grain-refining elements was proposed. These deoxidizers included three manganese-silicon-aluminum-titanium al- loys with and without boron and calcium, three titanium-aluminum ferroalloys with vanadium, molybdenum and zirconium, respectively, an aluminum-zirconium ferroalloy, and plain ferroboron. Their approximate compositions are given in Table I, and the results obtained so far in the investigation of their effects on steel are presented in the later parts of this paper. Method of Using Deoxidizers The deoxidizers listed in Table I were used in three series of 0.40 per cent carbon steels, which were melted in a small basic-lined induction furnace and cast in the form of I7-lb. ingots about 2.75 in. square. The basic charge for each heat was 10 lb. Armco iron and 6 lb. of clean low-carbon sheet-steel scrap. When melted, this charge was deoxidized with 15 grams of ferrosilicon, then about 500 grams of pig iron was added to give the desired carbon content. After the pig iron was dissolved, nickel shot and high-carbon ferrochromium were added if required, and additions of 80 per cent high-carbon ferromanganese and 50 per cent ferrosilicon were made to provide the proper amounts of those elements. Aluminum was added to every heat 2 min. after the silicon, for grain-size control and preliminary deoxidation. One minute later the special deoxidizer was added to the clean bare surface of the molten steel, and 2 min. afterward the steel was poured into the ingot mold, using a hot-top and pipe-preventing compound after pouring to decrease the depth of the shrinkage cavity. The special deoxidizers were used mostly in the form of about ½ to¾-in. lumps,

Jan 1, 1942

By Heinrich Ries

Jan 1, 1907

By C. M. Heath, B. W. Gonser

The importance of grain size and its control in wrought brass needs no lengthy discussion, since specifications so often make exact control imperative. Aids to this control are therefore of interest. The effect of a number of different elements on the grain growth of brass under various conditions of annealing has been reported in the technical literature. In particular, a paper by Cook and Miller1 a few years ago, with the discussion that followed, gave valuable information on the effects of iron, phosphorus, manganese, aluminum, aluminum plus nickel, and aluminum plus silicon. Price12 in his discussion of that paper, added a description of some commercial brasses that exhibited a grain-refining effect owing to the presence of 2 per cent A1 and 1 per cent Ni. Gibson and Doss3 have recently given data on the effect of iron on annealing high brass. No comprehensive study, however, has been given to the effect of additions of chromium. It has been the purpose of this investigation to determine the effect of adding various amounts of chromium to a plain cartridge brass, particularly in regard to the effect on grain growth in various annealing treatments after cold-working. Prepakation of Alloys Alloys of high-purity brass of 68.5 Cu, 31.5 Zn composition were made containing from 0 to 0.17 per cent Cr. These were produced in induction furnaces, using unlined graphite crucibles to hold the charge. The melts were cast into rectangular chill molds giving ingots about % by 3 by 10 in. in size.

Jan 1, 1938

By W. A. Tiller, J. P. McHugh

HE majority of liquidus and solidus surfaces in phase diagrams have been determined by the conventional cooling- and heating-curve techniques.' These techniques have two main shortcomings: 1) the solidus may be in considerable error due to the difficulty involved in completely homogenizing the solid and 2) the determination of liquidus and solidus in more than a two-component system does not enable one to determine tie-lines connecting the specific equilibrium solid and liquid compositions. However, in a recent paper by one of the authors,' a method was suggested whereby the liquidus and solidus surfaces plus tie-lines in an n-component system may be determined. This method utilizes a controlled solidification technique and assumes that interface equilibrium exists during freezing. The present work was undertaken with a twofold purpose; first, to determine the liquidus and solidus lines in the pseudo-binary system Bi2Te3-Bi2Se3 by heating- and cooling-curve techniques and, second, to determine the partition coefficients of Te and Se in the BizTe3-,Sex system by controlled solidifica- tion techniques. The two sets of results can be compared to test the accuracy of the controlled solidification method. EXPERIMENTAL I—The starting materials for this study were 997999 pct Bi, Te, and Se, obtained from the American Smelting and Refining Co. The compounds BizTe, and Bi2Se3 were each prepared by melting together stoichiometric amounts of the elements, followed by twelve zone-refining passes. This produced homogeneous bars of the compounds for use in the phase-diagram studies. The apparatus used to obtain heating and cooling curves is illustrated schematically in Fig. 1. The alloy samples were located in a graphite crucible placed in a stainless steel canister. The canister was supported in a heavily lagged pit furnace by a device which oscillated the canister about its vertical axis at a frequency of about 3 cycles per sec during heating and cooling-curve runs. The graphite crucible was designed to minimize the thermal coupling of the sample to the furnace. A thin graphite sleeve separated the alloy sample from the stainless steel tube that housed the thermo-

Jan 1, 1960

By Herbert H. Kellogg

RECENTLY the long-chain primary amines have been used extensively for the flotation of silicate minerals. The use of amines to float sulphide minerals has been investigated by several authors1-5,18 but most of this work has been done with the short-chain (less than six carbon atoms) primary amine compounds or the more expensive secondary, tertiary and quaternary amines. Perhaps the fact that the long-chain amines are good collectors for the common gangue minerals has led investigators to omit them from consideration as collectors for the selective flotation of metallic sulphides. The work reported in this paper was designed to investigate the use of a typical long-chain amine salt, lauryl amine hydrochloride, as a collector for the flotation of galena-sphalerite ores. The results show that lauryl amine hydrochloride (LAmHCI), when used in small amounts, is a good collector for the selective flotation of sphalerite and galena from the common gangue minerals. The differential flotation of sphalerite from galena was not accomplished but the amine flotation of sphalerite after the standard xanthate flotation of galena is possible. The experimental work reported herein is not complete enough to be able to say whether amine flotation of lead-zinc ores would prove superior to xanthate flotation, or whether the method is even applicable to a more complex ore than the one used for this work. However, the apparent reagent costs for the flotation operations described in this paper seem to be less than for xanthate flotation. This fact alone should be sufficient to encourage the millman to investigate the use of these amine reagents, especially as these reagents are available on a commercial scale at a reasonable price. This paper has as its secondary purposes to illustrate how contact-angle measurements have aided in this investigation, and to bring forward some evidence concerning the mechanism of the collecting action of primary amines. CONTACT-ANGLE TESTS The contact-angle measurements were made by the method described by del Giudice6 and used in recent work by Taggart and his collaborators.7-9 The mineral specimens for the contact-angle tests were carefully chosen, to avoid cracks and inclusions of other minerals. All specimens were mounted in "transoptic" plastic mounts and the surfaces were cleaned by polishing with levigated alumina on a cloth-covered glass polishing wheel. Distilled water was used on the lap during the polishing and at all subsequent steps in the contact-angle tests. The mounted mineral specimens were handled with glass forceps and special care was exercised to prevent exposure of the dean surface to air or any other source of contamination.

Jan 1, 1945

By George F. Comstock

It has been reported recently1 that the hardenability and toughness of forging steels may be improved appreciably by the use of complex deoxidizers containing titanium, aluminum, and vanadium. In the light of these results, an investigation of similar deoxidizers containing various hardening and grain-refining elements was proposed. These deoxidizers included three manganese-silicon-aluminum-titanium al- loys with and without boron and calcium, three titanium-aluminum ferroalloys with vanadium, molybdenum and zirconium, respectively, an aluminum-zirconium ferroalloy, and plain ferroboron. Their approximate compositions are given in Table I, and the results obtained so far in the investigation of their effects on steel are presented in the later parts of this paper. Method of Using Deoxidizers The deoxidizers listed in Table I were used in three series of 0.40 per cent carbon steels, which were melted in a small basic-lined induction furnace and cast in the form of I7-lb. ingots about 2.75 in. square. The basic charge for each heat was 10 lb. Armco iron and 6 lb. of clean low-carbon sheet-steel scrap. When melted, this charge was deoxidized with 15 grams of ferrosilicon, then about 500 grams of pig iron was added to give the desired carbon content. After the pig iron was dissolved, nickel shot and high-carbon ferrochromium were added if required, and additions of 80 per cent high-carbon ferromanganese and 50 per cent ferrosilicon were made to provide the proper amounts of those elements. Aluminum was added to every heat 2 min. after the silicon, for grain-size control and preliminary deoxidation. One minute later the special deoxidizer was added to the clean bare surface of the molten steel, and 2 min. afterward the steel was poured into the ingot mold, using a hot-top and pipe-preventing compound after pouring to decrease the depth of the shrinkage cavity. The special deoxidizers were used mostly in the form of about ½ to¾-in. lumps,

Jan 1, 1942

By Marie L. V. Gayler

WITHOUT diffusion taking place in liquid metals and alloys, no castings could be made; it is therefore the most important factor affecting the structure of metals. Diffusion involves the interchange of atoms, a process which takes place during the life history of an ingot. In the liquid, atoms are in a state of high thermal agitation, but this thermal vibration is reduced in amplitude with falling temperature. When solidification sets in, the atoms arrange themselves on an ordered space lattice and the changes in structure which take place in the solid are due to the interchange of atoms on this space lattice. The rate of atomic interchange-e.g., of diffusion-is most rapid at temperatures close to the melting point and decelerates as the temperature is lowered. At room temperature, the rate of diffusion is practically negligible in most alloys, and any change in structure can only be brought about by using methods which will accelerate the rate of diffusion. The rate of diffusion depends on three factors (I) temperature; (2) concentration gradient and (3) activation energy. The growth of grains and particles in the solid alloy also depend on these factors and are therefore intimately associated with diffusion. The rate of homogenization in a cast alloy depends on several factors, such as: (I) rate of solidification, which involves grain and particle size which, in their turn, depend on diffusion: (2) the nature of the constituents; (3) the temperature interval between the melting point of the metal or alloy and the temperature at which it is being heat-treated. It is well known that coarse, cast structures are extremely difficult-if possible to homogenize, and the finer the grain size and particle size, the more readily solid solution will take place. The rate of diffusion depends, also, largely on the nature of the constituents; for instance, copper and magnesium form solid solutions with aluminum quite readily but nickel and iron do not; neither do certain intermetallic compounds, such as alpha and beta FeSi. Furthermore, the actual formation of intermetallic compounds may be a very slow process, particularly when they are formed in the solid state as equilibrium products. For example, ßFeSi is formed in the solid as the result of the reaction aFeSi + Al?ß FeSi. The particles of aFeSi become sur¬rounded with a reaction ring of ßßFeSi. This layer is formed as the result of diffusion of atoms taking place between the aluminum matrix and aFeSi. As the amount of ßFeSi surrounding the core of aFeSi increases the concentration gradient becomes low and so the rate of diffusion of atoms also decreases until it practically ceases. This occurs after a comparatively thin layer of ßFeSi has been formed. It follows that when intermetallic compounds of this type are formed in the solid, as the result of diffusion, it is generally impossible ever to attain equilibrium, since the forma-

Jan 1, 1944

By Arthur G. Levy, Henry M. How

The purpose of the investigation on which this paper is based is to determine whether the structural change which occurs in the slow cooling of steel below the transformation range has an important effect on its engineering properties. We recognize two distinct things which occur in steel when it is brought from above to below the transformation range, first, the transformation proper, that is, the breaking up of the austenite or solid solution of the cementite in the remainder of the iron, and the liberation of its components as undissolved cementite and as ferrite or alpha iron; and second, a structural change consisting in the gradual coalescence of the ferrite and cementite respectively into larger and larger separate masses. Let us distinguish these from each other by speaking of them as " the transformation " and " the structural change " respectively. If the cooling is at all rapid the unevenness of contraction induces severe stress; so that in a sense a slow cooling has a third influence, the prevention of such stress. This transformation from austenite to ferrite plus cementite can complete itself only below the transformation range; and, because this structural change is a change in the structural arrangement of the products of that transformation, it too can complete itself only at temperatures below that range, say below 725°; and of these temperatures it is only those between 600° and 725° that give the metal sufficient mobility to permit this structural rearrangement to progress with ally rapidity. The transformation is now known to be rapid, but the structural change is relatively slow. The transformation, the liberation of the dissolved cementite from the state of solution in the austenite to a free state, leaves the steel structurally in the

Jan 1, 1913