Search Documents

E. D. Peters, Jr., Dorchester, Mass.: This paper of Mr. Keller's seems to me a step in a direction that has been very little exploited, and iff likely to lead to valuable practical re-

Jan 1, 1899

By Edward H. Robie

Jan 1, 1971

By H. B. Pulsifier

The following report on the structure of copper is the result of work done in the laboratory of the Rome Wire Co. early in 1925. Previous work had indicated to the author that excellent results might be expected if a suitable technique in surfacing and etching could be developed. The resources of the Rome Wire Co. enabled this metal to be studied more intensively than previously, although none of the materials were investigated exhaustively. The material presented is hardly more than a preliminary summary of the most obvious character of the metal; a much longer research would have been necessary to solve many of the pressing problems connected with the casting and working of copper. The Rome Wire Co. has generously released the paper; to Dr. E. H. Darby, technical supervisor of the company, are due particular thanks for his appreciation of the importance of metallographic study of copper and for his effective support in the prosecution of the work and in making its publication possible. Dendrites, Cells and Granules The microscope reveals at least three orders of structural units in copper, as in other metals. The largest structural units are the dendrites —spine-shaped crystals building up the masses of metal when it solidifies from a melt or is crystallized from solutions by chemicals or electricity. The nucleus cells, commonly called "grains," are the largest and most conspicuous units of recrystallized solid metal; the limitations of their growth usually confine their sizes to microscopic proportions, although in "single crystals" they may become as large as the piece of metal itself. The granules are the microscopic fine-structural blocks or laminations that build up the nucleus cells; they are revealed when metal is etched with suitable chemicals. The granules are commonly visible at 500 diameters magnification and are plainly visible at 1000 diameters; magnification of the granular surfaces up to 6000 to 9000 diameters shows no finer units, not because of lack of optical resolution but because the chemical attack has left an unfeatured smooth surface.

Jan 1, 1926

By Edgar Bain

SUMMARY THE results of an enquiry into the structural nature of some 70 iron alloys containing both nickel and chromium over a considerable range of concentration 'are briefly described in this paper. This study is a part of a comprehensive program of investigation into alloys involving chromium in progress at the Union Carbide and Carbon Research Laboratories. All the compositions studied contained carbon in amount comparable to commercial alloys.

Jan 3, 1927

By A. English, M. J. Greaves

This paper is a discussion of pelletizing systems developed over the last 15 to 20 years for the agglomeration of fine iron ore concentrates. Five different pelletizing systems are now in commercial use in the U.S., and for the purposes of comparison, estimated operating costs and capital costs for the construction of four of them are included. Capacities of existing commercial plants are examined, together with the anticipated capabilities of plants presently being built or projected. In just 21 years, the art of pelletizing iron ore concentrates has reached maturity with mastery of the separation of finely divided concentrates from low-grade iron ores and their agglomeration into pellets containing about 65% iron. This accomplishment has firmly established an improved feed for the blast furnace, with resulting benefits in faster reduction of burdens and greater economy of operation. The present production capacity of pelletizing facilities in the U.S. is about 20 million tons annually, and it is expected to double by 1970. The rapid expansion of pelletizing in the U. S. has been closely observed in European countries, notably in Sweden and Germany, where pioneer agglomerating techniques were developed early in this century. PELLETIZING PLANTS AND PROCESSES Twelve commercial pelletizing plants are presently in operation in the U. S. and Canada. An equal number are in various stages of engineering and construction, and many others are being considered. The pelletizing systems currently employed include shaft furnaces, horizontal grates using three different airflow arrangements, and grate kilns. The capacity of pelletizing operations in North America is shown in Table I. All of these plants are integrated with the mine, the ore-crushing facilities and the concentrating plant and are equipped with storage and loading-out facilities for the product. Normally, a pelletizing plant is composed of a shuttle conveyor above the receiving bins; balling equipment; a heat-hardening system including the necessary auxiliaries such as furnaces, burners and controls, ducts, fans, meters and instrumentation; fines recovery equipment; and product handling equipment. Also included are the necessary auxiliaries and utilities such as boilers or power plant; oil unloading and storage facilities; coal unloading storage, grinding and distribution facilities; and bentonite or other additive storage and distribution equipment. Shaft Furnaces: Vertical shaft furnaces used in this country are limited to the treatment of natural magnetite concentrates containing minor quantities of residual fluxing elements. Fig. 1 shows a perspective view of the shaft furnace with balling, feeding and pellet-handling equipment. An elevation of a shaft furnace is shown in Fig. 2. A commercial shaft furnace unit is about 45 ft in height with a 6 x 14-ft rectangular cross section and has a nominal production rate of approximately 50 gross tons of pellets per hour. The upper portion of the furnace shaft is constructed of fire brick as protection from the high process temperatures involved. The lower portion of the shaft is lined with abrasion-resistant brick to withstand erosion from the fired pellets. Rectangular-shaped, refractory-lined and insulated combustion chambers are situated on each side of the shaft furnace. Oil or gas is burned to produce high temperature gases which are forced into the furnace through ports located near the top of the combustion chambers. The shaft furnaces operate at a pressure of approximately 6 psi. Pellets are fed into the top of the furnace by a pantographic feeder designed to produce the desired pellet stockline. The furnace is kept filled at all times and pellets are fed and discharged from the furnace at the same rate. In early development, 10 to 12 lb of solid fuel was incorporated in the pellets. However, the main source of process heat is now derived from the combustion chamber gases. In some instances no solid fuel is used. The pellet movement in the shaft furnace is counter-current to the flow of gases. Ambient air is introduced through louvers at the lower end of the furnace, at about 6 psi, cooling the fired pellets and supplementing the heat of the high temperature gases from the combustion chamber ports. The zone of maximum temperature, located above the ports of the combus-

Jan 1, 1963

By Frank G. Snyder

The Precambrian of Midcontinent United States includes a metamorphic belt of probable Middle Precambrian age, a belt of Keweenawan volcanics and sediments, and widespread igneous activity that extended from Iowa to Texas. Most of the present structural configuration of the Midcontinent was developed by epeirogenic movements during the Paleozoic. The dominant elements are basins and arches. Three major metallogenic provinces occur in the Midcontinent. They include the Missouri Precambrian iron ores, the Lake Superior copper ores, and the Mississippi Valley lead-zincbarite- fluorite deposits. Several large iron deposits, occurring in rhyolite and andesite host rocks, are known. Both discordant massive bodies and replacement- type bodies occur. The iron deposits are believed to have been formed during the period of igneous activity. They are essentially the same age as the volcanics and older than the granites that intrude the volcanics. The Lake Superior copper ores include two established districts, the Keweenawan district and White Pine, and the copper-nickel deposits in the Duluth gabbro. The lead-zinc-barite-fluorite deposits include four major districts, Southeast Missouri, Upper Mississippi Valley, Tri-State, and Illinois-Kentucky, and at least eight minor districts. Ore may occur in stratiform deposits and in veins. The major districts all contain stratiform deposits, but several have produced appreciable quantities of vein ore. Only vein deposits are known in some of the smaller districts. The major features of all districts can be catalogued in terms of host rocks, structural patterns of districts, types of ore-bearing structures, and mineralogical characteristics. From these features, a Mississippi Valley type ore body, in its type area, can be defined.

Jan 1, 1968

By Bruno Nordberg

HOISTING is one of the earliest endeavors of man with machinery, for hoisting was probably used by the early Egyptians. Treadmills were used for general hoisting until early in the nineteenth century and it was a short step only to attach a Watt steam engine to the rope drum of a hoist. One of the earliest steam hoists was built for a coal mine at Frisne, near Valenciennes, France. It was a remarkable piece of engineering created by James Watt in 1811, using a wooden drum on a vertical shaft. This followed the crude hoist by Holtzhausen in 1803, which used a drum of wood on a horizontal shaft.1 In this country there were examples of crude mine hoists, which have been developed into the efficient machines in use today. African and Australian mines show examples of both extremes, and have an array of fine hoisting equipment exemplified in those built by British manufacturers. The influence of both English and American engineering in hoisting is interestingly evident in Canada. The information available to the writer does not reveal this to be true of South Africa, although American-built hoists have been furnished. Mining camps develop their own style of equipment, adapted to local conditions. For instance, the Butte mining district adheres to the straight drum with friction clutches, because of the great number of levels from which hoisting is done or to which men and material are lowered and the necessity for hoisting or lowering unbalanced. The north Michi-gan copper country uses both straight and cylindroconical drums and hoists continually in balance, so that the drums are not clutched to the main driving shaft. The Joplin mining district, Missouri, has its own peculiar small hoists. Other individual mines or localities in which a number of mines have been developed show individualisticc types of hoists, depending upon their particular problems. In each instance, however, the particular problem must be carefully analyzed, as conditions are seldom so near the same that a number of identical hoists can be used to advantage.

Jan 1, 1940

By F. Keller, A. H. Geisler

Some of the important changes that take place in the structure of aluminum alloys are largely submicroscopic in character. This is especially true of the changes that accompany age-hardening and recrystallization. Although improved metallographic practices have been helpful in indicating some of these changes indirectly, results are limited by the resolving power of optical microscope lenses. The electron microscope, however, provides a new and important means for investigating the fine structure of metals in a range not possible heretofore. It is anticipated that this microscope will yield new and useful information to metallurgists when suitable techniques are developed to utilize its very high resolving power. Several unique methods have been devised to permit the examination of the structure of opaque samples by the electron microscope. These are all based on the principle of producing a very thin film that represents the prepared surface of the opaque metal sample, which can be examined in the transmission microscope; however, the available methods fall into three categories, depending on the manner in which the film is obtained. With the oxide-film method developed by Mahl3-17 a very thin surface layer of the metallographic sample is converted into oxide by a thermal, chemical or anodic treatment. After removal from the metal sample by one of the special techniques described by Evans,19 this oxide film is examined in the electron microscope, and is found to portray the structure of the original metal surface. Films formed on aluminum,8,17 nickel,7 iron 3,8,9 and a nickel-beryllium alloy" by heating; films formed on iron 8.9 by chemical action; and films formed on aluminum3-16 by anodic oxidation, have been examined. The other two are more recent methods developed principally in this country; they consist in making the thin film in the form of a mold or replica of the surface contour of an etched sample. With the negative replica method the thin film is made directly on the sample; with the positive replica method it is made on a negative reproduction of the sample. With both methods, variations in the contour of the metal sample, caused mainly by etching, produce variations in the thickness of the surface replica. Because of the direct dependence of the amount of scattering of the illuminating electrons upon the thickness of the film penetrated, only the variations in thickness of the replica are responsible for tones in the electron image. Negative replicas are made by forming a thin film of some suitable material directly on the polished and etched metal sample, and derive their name from the fact that after removal from the sample they have the high and low points in the sample reversed, as shown in Fig. I. Nega-

Jan 1, 1944

By Morris M. Fine, Norwood B. Melcher

It is out of the question, at this time, to select any one prereduction process as superior to the others. It is apparent that several share a basic similarity and that within the groups listed in Part 1, the reduction vessel is sometimes the only significant variable. Claims as to the virtues of one machine over another are difficult to substantiate: one may be rapid, another thermally frugal. Based on published data, however, all seem to be performing adequately. It would appear that processes based on carbonized pellets are most applicable to foundry iron at low production rates. Adaptation to large scale manufacture of blast furnace hot metal or to agglomeration of fine concentrates at the mine site is much less likely.

Jan 8, 1966

By Gregory M. Dexter

Recent litigation in Pennsylvania between three coal-mining companies and a private water company resulted in the payment by the coal companies of the equivalent of about $500,000 to buy a new water supply to replace that which had been damaged by acid drainage from strip mining. An investigation of the relevant facts indicates that the water could have been treated by spending about $40,000 on equipment and $15,000 yearly for chemicals, labor, and power until the contamination could be reduced about 80 pct. The water company's supply, furthermore, had deteriorated largely by reason of dry weather before stripping was begun by the coal companies. Payment to the water company should not have exceeded $300,000 and could have been as low as $100,000. Strip mining of coal is common in Pennsylvania. The most important objection to it in Pennsylvania is generally acid pollution of runoff water. An outline of the methods, therefore, that could be used to reduce such pollution, to compare acid-contaminated waters, and to treat such waters to make them satisfactory for public and industrial use is worth-while. The watershed of the West P~M Water Co. covers about 4.5 square miles, 20 miles west of Pittsburgh, and has two 90,000,000 gal reservoirs sup- plying about 1,300,000 gal daily for public and industrial use of which 450,000 gal daily are for two railroads. The pollution arises from weathered derivatives of typical "Coal Measures"

Jan 1, 1949

By D. D. Smith, D. P. Squier, E. L. Dougherty

A system of differential equations describing the temperature behavior of fluid injected at constant surface temperature in a well is derived and .solved analytically. A formula for the fluid temperature at any time and depth is given, as well us a special formula valid for very large times. These formulas are used to calculate temperatures for several typical cases. The results indicate that, initially, the temperature of the water entering the formation is considerably lower than the injection temperature. This condition lasts for only a short period— less than three days for most cases of practical interest. Following this highly transient period, during which the temperature of the fluid entering the formation builds up to about 50 to 75 per cent of the injection temperature. the system enters a quasi-steady state in which the temperature changes are very slow. After severl years, the bottom-hole temperature will still be 50" to 100°F lower than the injection temperature, hilt the heat losses may he tolerable. INTRODUCTION Predicting the behavior of a hot-water flood requires that the temperature of the water entering the injection interval be estimated. This report describes the development and solution of a system of equations which describes the temperature behavior of the injected water in the wellbore with certain simplifying assumptions. The only previous means known to the authors for describing such a process is that of Moss and White.' Their results appear to be close to those obtained by our method in the practical cases which were compared; this agreement is largely due to the fact that in our method temperature soon approaches a quasi-steady state, as was assumed in their method throughout. However, our model covers all times, is continuous (whereas the Moss-White model depends on breaking the depth into discrete intervals) and. we feel. more closely describes the physical problem. FORMULATION OF THE PROBLEM PHYSICAL SYSTEM AND ASSUMPTIONS The injection procedure consists of pumping water at a fixed surface temperature T., down an infinitely long cylindrical well or tubing of inner radius Any material exterior to the water column such as mud, casing, or cement is regarded as part of the formation. The general behavior of the system may be described qualitatively as follows. When the hot water is first introduced into the system, the temperature difference between the formation and the water is large, resulting in a high rate of heat transfer. As a result, the temperature adjacent to the wellbore rises very quickly. Because the segment of the formation adjacent to the wellbore largely controls the heat transfer rate, the heat transfer rate will become relatively constant when this portion has reached a temperature close to that of the water opposite it. The temperature of the water and formation then increase very slowly with time. The length of the initial highly transient period and the temperature of the water at its conclusion will be functions of depth, injection rate, injection-string radius, surface injection temperature and the physical properties associated with the water-formation system. The following additional assumptions were made. 1. There is no heat transfer by radiation in the system. 2. There is no heat transfer by conduction in the vertical direction in either the injection stream or the formation. 3. The linear volumetric and mass flow rate of the water is constant throughout the injection stream. 4. No horizontal temperature gradient exists in the injection stream. 5. The product of density and heat capacity is constant for both the water and the formation, and the formation thermal conductivity is constant. 6. Initially, both the water in the wellbore and the reservoir are at a temperature given by the (constant) ambient surface temperature plus the product of depth and geothermal gradient (assumed constant). At large distances for the wellbore (r m), the formation will remain at this temperature. 7. The water temperature and the formation temperature at r — r,, are equal for all depths D. DERIVATION OF EQUATIONS The differential equation satisfied by the fluid temperature T,(D, t), which is obtained by writing a heat balance on a cylindrical differential of volume dV of the injection string between the depths D and D i dD, is

By A. J. de Witte

It has been observed that upon invasion of a sand containing oil or gas and connate water by mud filtrate the hydrocarbons are more rapidly flushed by the filtrate than is the connate water.' In time, it appears that the following displacement pattern emerges: oil (or gas) is being swept ahead by connate water which, in turn, is pushed by invading fluid. Eventually the connate water may have "banked up" sufficiently to form a zone of appreciable thickness leading the invading front. In the extreme case, Fig. 1 shows how the situation will develop.' Immediately adjacent to the borehole (radius r) there is a zone, the invaded zone proper, where the connate water has been flushed out completely and which contains only residual oil or gas and mud filtrate. This zone (extending out to a radius ri) grades more or less abruptly into the next (thickness A), which contains only residual hydrocarbon and connate water. Beyond it, again more or less sharply bounded, extends the virgin formation with the original interstitial water saturation Sw. The various saturations are indicated in Fig. 1. The three zones generally will be marked by resistivity contrasts owing to their different fluid contents. As the connate water is usually more saline than the invading fluid, the second zone having a high connate water saturation forms a concentric cylindrical ring or annulus of low resistivity R, around the borehole.',' It will be referred to as the "low zone." Fig. 1 shows schematically the resistivity profile. It is clear that the phenomenon of a low zone could not occur in invaded water sands. The presence of a low zone, therefore, would be a qualitative indication of a hydrocarbon-bearing formation. Granted that the phenomenon is real, if it were pronounced enough to be detected, one might thereby have a means of locating oil or gas in the ground. This is the aim of the "displacement logging" method.' In any case, the presence of a low resistivity zone will affect the reading of electric logs. Using conventional log interpretation techniques, one must be aware of this and, if necessary, correct for it. Whether correction or detection should be the goal will depend primarily on the magnitude of the effect. The type of log which is likely to be affected most is the induction log. The current pattern of an induction log is concentric with the borehole. Any concentric ring of low resistivity, therefore, will tend to become crowded by current lines. This zone of maximum current density will obscure the relative contributions to the current conduction by other portions of a bed making, for instance, the contribution of the virgin formation less significant and thus detracting from the value or the induction log as an R, reading device. The present note is intended to ascertain the maximum possible effect of a low zone in the extreme case portrayed by Fig. 1 on three commercially available types of induction logs, sc., 5 FF 27, 5 FF 40 and 3 F 60. Type 5 FF 27 or 5 PF 40 is currently run in conjunction with a 16 in. normal and SP log. This combination is gradually replacing the regular electric survey (two normals and one lateral) as a standard log in many areas. On the basis of the scheme of Fig. 1 (sharp boundaries between successive zones), the thickness of the low zone may be computed for various amounts of infiltration measured by the ratio of invaded zone diameter to hole diameter D,/d. Referring to Fig. 1, we can set up a material balance for the water displaced from the invaded zone proper and the water present in the low zone. The volume of connate water displaced from invaded zone upon flushing by mud filtrate is: V1 = e p (r2 - r2) ? Sw . where c = bed thickness ? = porosity Su, = original connate water satu-ration. The volume of water finally accu-mulated in the low zone is: Vz = e p [(r1 -?)2 - r2 4] ? Sw . where SW1 = 1 — Sor = "water" saturation in the invaded and low zones both. The volume of water originally present in the low zone is:

Jan 1, 1958

By K. A. ACKLEY

The petroleum industry experienced a year of satisfactory accomplishment in Oklahoma during 1945. Crude oil production was increased, a new record for recent years was established in well completions, and refinery operations were maintained at a maximum level. Daily average crude oil production increased to 382,000 bbl., reflecting a 13.5 per cent gain compared with production during the previous pear. Total wells drilled during 1945 amounted to 2556, a gain of 28.7 per cent over 1944 Refinery throughout averaged 187,500 bbl. daily, an increase of approximately 4 percent over the preceding year.

Jan 1, 1946

Joseph W. RichaRds, South Bethlehem, Pa. (communication to the Secretary*): The hold experiment of Mr. James Gayley in drying the blast used in the Isabella furnace has attracted the attention of the whole metallurgical world, and has given rise to a wide discussion of the reasons for its great success. Mr. Gayley and the capitalists who backed him in his work deserve congratulations on the success of the venture, not only because it succeeded, but because they have been rewarded far beyond the maximum that could be expected from theory or probability. To state the case in its simplest terms, all that could have been predicted was: (1) that the removal of the moisture from the blaet would result in the saving of the heat required for its decomposition, representing from 3 to 5 per cent. of the heat-value of the coke used; hence about that quantity of fuel might be saved; (2) that the furnace would be somewhat more independent of variations in the weather; (3) that the campaign would be a little hotter; and (4) that the speed of the blowing-eugines would be decreased, at least in amount proportionate to the reduction in temperature of the air led to them. I do not think anyone anticipated a much larger output per day. The results actually attained were: (1) the furnace made an increase of 24.86 per cent. in the output of pig-iron per day; (2) it consumed 19.6 per cent. less coke per ton of pig-iron made; (3) the blowing-engines were run 15.8 per cent. slower; and (4) the saving in power made up for the power required to run the refrigerating-plant. In addition, the blast was hotter; the waste-gases cooler, because of their smaller volume; and there was a greater proportion of carbon dioxide to carbon

Jan 1, 1906

By G. G. Brown

Enthalpy-entropy diagrams are presented for natural gases of 0.6, 0.7, 0.8, 0.9, and 1.0 gravity over the pressure range of 5 to 10,000 Ib. per sq. in. and temperature range of 32º to 700°F. The charts indicate directly the work requirement and temperature rise for adiabatic compression or temperature change for free emansion of natural eases. Computation and Uses of Charts The Mollier diagram (Fig. 4), in which the enthalpy (heat content) is plotted against the entropy with lines of constant temperature, pressure,, and in some cases volume, has been found most convenient when dealing with the compression, expansion, and flow of fluids. In dealing with the flow of fluids, the sum of the increase in the enthalpy, AH, plus the increase in kinetic energy, AM —, plus the increase in potential energy, ?MZ, representing the total increase in energy of the fluid in flow, is equal to the sum of the heat q, and work added, —w, to the fluid while flowing between the entrance and exit of the flow system. AH + AM— + ?MZ = q-w [1] In cases where there is no significant change in potential energy or in kinetic energy (velocity), it follows that the increase in enthalpy is equal to the total energy supplied to the fluid. Under such conditions' the changes in the property of the fluid as it flows through a throttling valve, choke, or any other similar arrangement, may be read directly from the enthalpy-entropy diagram by following a horizolltal line between the known pressures' When compressing Or expanding a gas by means of a Or or engine in which no heat is added to or subtracted from the gas, but only work done, the changes in the properties of the gas may be determined along a vertical line of constant entropy between the entering and exit pressures. The power required for the compression of the gas may be readily determined by converting the increase in enthalpy into the desired units. The enthalpy-entropy diagram for natural gases is to the gas engineer what the steam diagram is to the steam-power engineer. For this reason it would be extremely convenient if a reasonably satisfactory enthalpy-entropy diagram could be prepared as a function of the gravity of the gas. A careful study of the known properties of natural gas indicate that this is possible. The effect of temperature upon the enthalpy at constant pressure is expressed as the "heat capacity" or "specific heat" of the gas. The best available data for natural and petroleum refinery gases indicates the relationship shown in Fig. I. From this it is clear that the specific heat of natural gases is a function only of the gas gravity and the temperature at atmospheric pressure. The effect of pressure on the enthalpy of natural gases is dependent upon the pressure-volume-temperature relationships,

Jan 1, 1945

By H. B. Pulsifer

THIS paper outlines a method for rapid production of flat, granular surfaces on many of the medium hard- alloys. Grinding wheels and fabrics on wheels are not used; the purpose is accomplished by rubbing on emery papers and on fine abrasives heaped on hand boards. The advantages of chromic acid in the solutions for etching nickel and copper alloys are explained. Steels may require an additional step in the mechanical smoothing owing to the lack of an ideal etchant. Chloric acid is a. rapid etchant for steel. Thirty-six photomicrographs illustrate the steps in smoothing and the clearness with which structures can be rapidly exposed. New structures in low-carbon steels are announced. After a little practice, many materials can be finished within two or three minutes. CUPRONICKELS In the previous papers on the metallography of copper and magnesium which the author has presented to this Institute there has been an attempt to demonstrate the advantages of minimizing the mechanical work of surfacing and depending more on chemical means; the present paper continues the research into a still wider field. It is obvious that the success of a chemical method for smoothing and etching depends almost entirely on the use of a suitable reagent. The etchant must remove the surface granulations and outline the structures. A very special type of reaction between reagent and metal must be displayed. Promiscuous corrosion or the intensification of the attack about local couples -formed by impurities or components must not be in evidence. There are several reagents that etch highly polished nickel and copper alloys very well. Acidified ferric chloride solutions, concentrated and dilute nitric acid solutions, and nitric and acetic acids in acetone have -been used to good advantage for the purpose. However, if they are expected to etch rather deeply-that is, smooth as well as characterize-the results may be far from satisfactory.

Jan 1, 1928

By B. Foley

IN THE first report1 disks of steel of known composition and history were exposed, under carefully prescribed conditions, to impacts of explosion products resulting from the explosion of 50-gm. charges of explosives having well-determined rates of detonation, or to impacts of a weight of known mass, falling through measured distances. There were available at the Bureau of Mines Experiment Station five explosives, having rates of detonation of 5716, 4470, 3190, 2296, and 1523 meters per second. It being desired to continue this exposure downward, and no explosives with a lesser rate of detonation being at hand, resort was had to the impact of a falling weight, the differences in the velocity of impact being attained by varying the height from which the weight was allowed to fall. It was expected by this means to demonstrate experimentally that the development of Neumann bands was determined by the suddenness of the deformation of the metal in which they were produced. But while progressive deformations were obtained with the explosive arges, the falling-weight method failed because the tup was ogressively deformed, also the disks were so flattened as to be unfit for metallographic examination. A return, therefore, has been made to the use of explosives as the source of energy, an air-gap being interposed between the charge of explosive and the disk, as the effect diminishes as the function of the distance between the charge and the object on which the products of its explosion, or the shock wave from its detonation, impinge. The details of the arrangement of the tests by the air-gap method were the same as those described by Foley and Howell,2 except that after the system had been set up and the desired apparent specific gravity for the explosive

Jan 2, 1926

By William Paxton Hewitt

Mineral deposits of western Utah and eastern and central Nevada have produced in excess of $8,500,000,000 since 1871. Through 1965, Bingham Canyon had produced over $4,600,000,000 and seven other camps over $100,000,000 each, principally from base metals. In addition, they yield iron and uranium ores; contain the world's largest beryllium reserves; and have produced the United States' most important gold discovery in 25 years. The area is famous for its silver production and its bonanza-type precious metal deposits, but such production has become unimportant. The area's greatest producers of metallic wealth are base-metal deposits in limestones and porphyry-type copper ores. In contrast to silver's decline, gold production has been rising-the result of by-product operations at Bingham Canyon. The area also contains gold deposits in which the gold is so finely disseminated it is not recoverable by panning. The area's gold ores frequently are associated with realgar, cinnabar, and carbon. The ore deposits generally are attributed to Tertiary intrusives,* but, at Mountain City, they may be related to Paleozoic volcanism. Mountain City has yielded rich chalcocite from quartz-pyrite-chalcopyrite bodies in siliceous sediments. Regional stratigraphy and structure are difficult to interpret, 69 per cent of the area being obscured by alluvium or volcanics. In general, central Nevada consists of chert, shale, silty sandstones, lavas, and pyroclastics; eastern Nevada and western Utah of many alternations of limestone, shale, and sandstone. Central Nevada has been structurally active since late Devonian. Although granitic stocks may have intruded eastern Nevada and western Utah prior to the Cretaceous, these areas remained quite stable until affected by the Laramide Revolution. Precambrian exposures, occupying 3 per cent of the area, have not been important hosts. However, the question is raised as to whether Precambrian carbonates, properly situated with respect to invading mineralizers, might yet prove to be important. This paper describes 16 precious metal camps, 6 limestone replacement districts, 2 silver-base metal vein deposits, and 9 miscellaneous types and discusses briefly the 11 * Some ores, as at Ely, are associated with intrusives of. Cretaceous age. major camps that are described in detail in this Volume.

Jan 1, 1968

By Robert M. Grogan, James C. Bradbury

The Illinois-Kentucky mining district has, since 1880, accounted for 80 per cent of all U.S. production of fluorspar. The ore deposits are of two types: vein deposits formed by fissure fillings along faults and bedding-replacement deposits formed by the replacement of strata at certain favored stratigraphic positions along minor faults and fractures. Fluorite is the chief valuable mineral in the deposits. Sphalerite and galena commonly are present in small amounts but, in some ore bodies, may form a substantial part of the valuable constituents of the ore. Calcite is the chief gangue mineral; quartz and barite Exposed strata range from Devonian are present in various amounts. through Pennsylvanian in age. Igneous intrusive rocks occur as mafic dikes and sills and intrusive breccia dikes and plugs. Structurally, the district is situated on a generally northwest- trending arch that has been sliced into a series of long, narrow blocks by normal faults that trend northeastward. The structural The localization of the ore deposits by faults and fractures, the association of fluorite mineralization with intrusive breccias, and various lines of petrographic and geochemical evidence indicate that the fluorite-zinc-lead deposits were epigenetic and deposited by solutions emanating from a deep alkalic magma.

Jan 1, 1968

By J. R. FINLA

THE three great war periods of recent times involving the-chief industrial, commercial, and military nations of the world have been the following: 1. Wars centering around the French Republic and Napoleon Bonaparte, .1791-1815;. involving every nation in Europe, parts of Asia Minor and *North Africa., and the United States of America. 2. Wars in Europe, Asia, and North -America beginning with the Crimean War, 1854-56, the British Empire, France, Sardinia, and Turkey against Russia; the Sepoy rebellion in India, -1857; -war of France . and Sardinia against ..Austria in Italy, .185.9; :the Taiping rebellion in China, 1861; Civil War in , America, 1861-65; French. occupation .of .M Mexico, .1863; Prussian war against :Denmark, :1864; (Prussia and Italy against Austria sand various -south German : states, 1866; :the Franco-German War, 1870.7,1.

Jan 1, 1931