Search Documents

By F. V. Lenel

This discussion is concerned with the method of manufacturing, the design possibilities, and the properties of pole pieces for direct-current electric . motors and generators made from iron powder. In such applications as pole pieces, the electric and magnetic properties of the material are of major importance, therefore they are discussed somewhat more fully. However, the main advantage in making pole pieces from powders lies in the rapid and inexpensive method of manufacturing these pieces, and in the flexibility of design, rather than in their superior electrical properties. As a matter of fact, pole pieces from iron powder have found their principal field of usefulness in small electric motors for controls and similar applications where the highest possible flux density in a given design is not required. Fig. I shows a number of different designs for pole pieces made from iron powder. The steps involved in fabricating them are: (I) briquetting—with each stroke of the briquetting press a complete . pole piece is produced; (2) sintering, and (3) sizing, which is a one-step coining operation in a hand-operated punch press. Conventionally small pole pieces are made from laminated electrical sheet steel stock by punching out the laminations and riveting them together (Fig. 2). The powder method has the advantage of being rapid and inexpensive; also, it makes possible the molding of pole pieces with a round hub, which are better from a design standpoint, as will be shown later. It is difficult to make such round-hubbed pieces from laminated stock. The pole pieces could, of course, be machined from solid stock, but this method is not widely used. The raw material for making pole pieces from powder is straight iron powder without the addition of any alloying ingredients. However, the grade of powder used is of considerable importance, as will be shown later when the influence of the grade of iron powder upon the magnetic properties is discussed. Pole pieces are briquetted in the same way that other iron-powder machine parts are made. Because the pole pieces are flanged—i.e., they have a hub and a wing section—they are made in presses that apply pressure from both ends. For best mechanical and magnetic properties, the density throughout the piece should be even and also should be constant from piece to piece. For that reason a powder of constant compressibility from batch to batch is needed for briquetting pole pieces. One method of obtaining the required magnetic properties is to sinter the pole pieces at temperatures higher than are used for most iron-powder parts. A temperature of 2400°F. and an atmosphere of hydrogen has been found satisfactory. No automatic furnaces of the roller hearth or mesh-belt type have yet been developed for such high temperatures. A box-type furnace heated with Globar heating ele-

Jan 1, 1945

By Walter Fuchs

IT is now generally conceded that coal is the product of deposition and transformation of debris of forests and swamps.29 Ample data are available to illustrate the metamorphosis of biochemical substances through biological action; other data show the progressive regional metamorphism existing in coal beds;25 and numerous examples of change effected by intrusion of igneous dikes into coal deposits have been established .R3 However, often the relative importance of the biological and the geological factor in determining the character of the various natural coals is a debatable question. Since both biological and geological factors are ever present in nature, the problem, at first glance, would appear to resemble certain probability problems: specifically the simultaneous toss of two coins, with the biological factor as heads and the geological as tails. The probability is 2:I for the combined effect of both factors, as compared to the exclusive effect of either one, if the a priori probability is the same for each factor. This condition can be analyzed by a thermodynamic treatment of data, which may be obtained from a consideration of pertinent biological, chemical, geophysical and geological facts. SYNOPSIS OF BIOLOGICAL AND CHEMICAL FACTS The biosphere is not sterile; i.e., microorganisms are always present. Microorganisms have been established in the ocean deep, under the ice of the polar regions, in the sand of the deserts, and in swamps far below the surface. The various biological media may be acid, neutral, or alkaline, and they may or may not be readily accessible to air. Microorganisms are encountered almost everywhere, except where the temperature is not within the range tolerable by microbial life. Of course, with changing conditions, the type of microorganisms will change. All chemical products of life-proteins, fats, carbohydrates, lignins, waxes, resinsmay serve as a habitat of microorganisms. In the decomposition of a medium, some microorganisms macerate organic matter mechanically and remove certain constituents for their own nutrition; others decompose a large part of the organic matter but may leave certain constituents undecomposed. Some attack only certain specific ingredients of the organic matter. All of them build up cell substance. The nitrogen content of the medium largely determines the degree of decomposition. Below 1.7 per cent nitrogen, growth of microorganisms and hence decomposition of organic material is retarded; consequently organic material will accumulate.17,32 Such accumulations of organic material may give coal eventually. Coals differ in type and rank. The nature of the original vegetation and the conditions attending the transformation of the accumulated debris determine the type of coal such as bright, splint, cannel, and algal or boghead coals. Chemical analysis of representative samples of a given type of

Jan 1, 1941

By Heinrich Ries

I. INTRODUCTION. THE facts is presented in this paper, based chiefly on recon¬naissance made, during the summer of 1903, by myself and my assistant, Mr. R.. C. Brooks, cover practically all that portion of Texas lying east of the 99th meridian. The work was undertaken for the University of Texas Mineral Survey, and was to have been extended over the entire State, but the sudden termination of the survey prevented even the official publication of the results already obtained. Most of the mineral resources of Texas were fully treated by the First Geological Survey, but the clay-industry was tit that time little developed, so that only a few scattered notes concerning it are to be found in the Survey reports. The extensive exploitation of the clay-deposits, however, has emphasized their commercial importance, and has also made accessible many facts of exceptional interest concerning their geologic conditions. The erection of new plants for the utilization of clay-products is usually preceded by more or less prospecting, which, by reason of the scarcity of outcrops, and the geologic and topographic conditions of eastern and southeastern Texas, is often slow and difficult work. This is especially true in the Tertiary and Pleistocene areas, where the structural conditions much resemble those of the Atlantic coastal plain, the deposits being mostly lenticular in form, and surrounded by beds of sand. II. GENERAL GEOLOGY OF THE CLAY-DEPOSITS. The accompanying sketch-map, Fig. 1, shows the location of nearly all the deposits examined, their relation to the geology of the State, and the type of clay found in each. The geology is based on the published work of Hill, Cummins, Tail, Adams, Hayes and Kennedy, but the boundaries have unfortunately not been determined over the entire region covered by the map, and, in many areas, are only approximate. It will be seen that the clay-deposits range from Carboniferous to Pleistocene in age, the older deposits being found in the northwestern part of the area, while those of Cretaceous and Tertiary age lie to the east, southeast and south. The Pleistocene clays are found in part in a belt along the coast, and in part along many of the larger rivers, where they often underlie extensive terraces.

Sep 1, 1906

By Richard Paul Seelig

THE following review covers published information on pressing of metal powders at room temperature. Only those operations are considered which occur between the time the powder is filled into the cavity and the compact is ejected from the die. Thus, this review does not concern hot pressing, coining or sizing feed or flow problems, commercial presses nor designs. It was also necessary to disregard to a large extent the effect of pressing on subsequent operations and on properties after sintering. The pressing operation is considered independently in its function to compact loose metal powder into useful shapes which can subsequently be handled. There are some comments by the writer in connection with a few of the findings quoted in the literature in order to stimulate thought and discussion. The selection of references quoted in the text is in some cases arbitrary although an attempt was made to favor papers containing novel ideas, techniques or results which may stimulate future research. In order to enable the reader to check further into the subjects mentioned, the original, rather extensive, bibliography is appended even though not all the references are touched on in the printed version of this review. EXPERIMENTAL APPROACH The equipment used by various workers, for example a die design created by Bridgman,22 is very interesting. The die insert has a conical external surface. The vertical pressure exerted on the punch transmits itself to the die which in turn is pushed harder into its tapered retainer. Thus, the higher the pressure exerted on the punch, the higher also the pressure exerted inwards on the die inserts. In as much as this pressure counteracts the internal pressure from the compact the two stresses balance each other so that it is possible to obtain tremendous pressures without breaking the die. The die collar was made from an oil hardening tool steel, heat treated to a tensile strength of some 300,000 psi. The die was closed at the bottom by a plug made from special tool steels. Bridgman found that there is no steel which will withstand a compressive stress of 700,000 psi without continuous slow flow or immediate fracture. Therefore, the only material suitable for use in the pressing punch was sintered carbide. In view of the ingenious design it was possible to use special tool steel as die material. Jones22 raises the question whether this method of pressing has practical application in powder metallurgy. Al- though these tremendous pressures cannot readily be utilized without many special precautions, the tapered die and retainer idea is believed to be useful even for lower pressures. Bridgman, himself,8 calls attention to the fact that the properties

Jan 1, 1947

By John Mathews

IT is a great honor to be asked by. the Board of Directors of this Institute to deliver the Henry Marion Howe lecture. The invitation carries with it a great responsibility, which I accept with considerable hesitation and with a feeling of unworthiness to perform the duties expected of me in this hour devoted to the memory of the life, character, and work of the late Professor Howe. Many of you recall the scholarly address delivered here a year ago by Prof. Albert Sauveur, and the beautiful tribute he paid-to his friend and colleague of many years in the great work of changing the art of iron making into the science of iron. My association with Professor Howe, was of brief duration-only one year-and the relation was that of pupil to teacher. My feeling toward him in later years was always that of a humble disciple at the feet of a master. He attained his third academic degree in the year that I was born. I recall the pride I felt when, after entering the, steel industry, I received from him, from time to time, letters asking for information or, perchance, asking my opinion, and he was always most punctilious in acknowledging the source of such bits of information in his writings. It was also my good fortune to sit at the feet of another great teacher-Sir William Roberts-Austen, at the Royal School of Mines. I mention him because his name was used by Osmond in coining the word "austenite," which is the subject of this address, and Osmond's suggestion was heartily approved by Howe. These three international metallurgists were the best of friends and delighted to honor the achievements of one another. There are other reasons for mentioning Roberts-Austen at this time. It was an introduction from Howe that opened to me the door of his -laboratory as well as of his heart. It was while at Roberts-Austen's laboratory that I .worked side by side with William Campbell

Jan 4, 1925

THE solid nonmetallic inclusions present to some extent in all commercial steels have been variously designated. In early references they were usually called slag inclusions, and this terminology is still retained to some extent. On the premise that all nonmetallic matter produced in a metallurgical process is slag, this can be justified. We have come to think of slag, however, in a more restricted sense, and calling these particles slag inclusions is further objectionable because it fosters the erroneous concept that they are actually incorporated portions of furnace slag. Rarely is this true. The term sonims (coined from solid nonmetallic impurities) was proposed many years ago but never came into common use. In general, the term non-metallic inclusions seems to be satisfactory and adequate. NATURE AND CONS1lTUTION OF NONMETALLIC INCLUSIONS From the standpoint of origin, inclusions fall naturally into two classes: (1) those occurring as a result of reactions taking place in the body of molten or solidifying metal and (2) those resulting from mechanical incorporation of refractories or other materials with which molten steel comes in contact. The former are by far the more numerous and have been called indigenous, natural, or native inclusions. The latter are by their very nature sporadic in occurrence and have been called exogenous, accidental, adventitious, or foreign inclusions. They are often referred to as the "slag-stringer" type, though here also the material is not likely to be furnace slag. Substances Found in Inclusions. Nonmetallic inclusions are composed principally of oxides and sulfides but carbides and nitrides sometimes play an important role. In the case of indigenous inclusions the reactions by which these particles are precipitated from molten or solidifying steel may be caused by: (1) oxidation such as may occur during refining or during tapping and teeming, (2) deoxidation by added alloys, (3) change

Jan 1, 1964

By D. B. RUSHhIORE

I. INTRODUCTION. OF primary importance in mine-installations is the hoist, which has a very direct bearing on the successful operation of a mine. Conditions vary greatly with different mines, and especially in different localities. Such factors as depth, incline, the number of levels, permissible or desirable speeds, conditions of ore, etc., are always more or less special in each case. Veins of ore are never exactly duplicated, and the nature of the ground through which shafts are sunk may considerably modify permissible values. As mining-laws are made by the different States, they necessarily vary somewhat, and, even when not fully observed, they introduce factors which qualify the conditions of hoisting men and ore. The amount of timbering required is often of importance as relating to hoisting-conditions. Methods of loading ore affect the time required, as also does the question of the use of cars or skips. Safety-precautions must be very carefully considered, and the number of men in each mine, the number of compartments, and often the method of removing water from the mine, must. have careful consideration. While a general discussion of the subject. of hoisting is possible, most cases are entirely special, and can be considered only in connection with the peculiar conditions pertaining to that particular installation. The cost of installation of the hoisting-plant may be an appreciable amount, while the cost of raising the ore may be but a small part of the total operating-charge. In many cases, however, the output of the mine is limited by the capacity of the hoist, and the latter thus becomes of the first importance. * Presented also, by mutual agreement, at the meeting of the American Institute of Electrical Engineers, New York, N. Y., Mar. 11, 1910.

May 1, 1910

By George J. Young

DR . JOHN A . CHURCH, in his treatise on the Comstock Locle 1 gave a full and clear account of the conditions of the mine during the period of greatest activity. The difficulties in the way of deep mining at that time were excessive water and high temperature. The drainage of the mines taxed the financial resources of the mining companies, and the high temperatures restricted the capacity of the miners for underground labor. In spite of these difficulties exploratory work was continued until the financial burden of removing the water became too great. The companies then restricted the work to the upper levels. The years 1883 to 1886 marked the period of cessation of deep mining. For 12 years thereafter mining was confined to the levels above the Sutro tunnel; and, while the question of drainage was more or less agitated, nothing of importance was done until the formation of the Comstock Pumping Association in 1898. Since that time successive levels have been drained until, at present, on the north-end mines, a depth of 700 ft. below the Sutro-tunnel level has been reached. Mining is now carried on in the Ophir mine from the 1,700- to the 2,200-ft. levels, and a winze is being sunk to make connection with the 2,300-ft. level (the 2,450 ft. of the C. & C. shaft). In 1903-the Ward Shaft Association was formed to undertake the draining of the Central and Gold Hill group of mines, and at the present time a depth of 2,500 ft. has been reached in the Ward shaft. The situation at the Ward looks promis¬ing, and the 3,000-ft. level may be reached in the near future. It is proposed to establish a large pumping-station on this level, and then begin the opening of known ore-bodies and the prospecting for new ones. The main factors which have contributed to the successful solution of the drainage problem are the Sutro tunnel, the use of the hydraulic elevator as a sinking-pump, the concentration of pumping-units, and cheap electrical power. The question of high temperature and its control still remains as a minor but important problem. The temperatures encountered in the new workings are as great as those in the earlier periods. The Comstock was considered the hottest group of mines in the world, and I am not aware of similar conditions in any other mining-district. A water-temperature as high as 160° F. has been reported from the Ward shaft, and temperatures below the Sutro tunnel are very high in many instances.

Nov 1, 1909

By B. P. Nutter, M. Lebourg, J. A. McAlister

The Multi-Flow Evaluator (MFE) is a new system of tools providing an original approach in drill-stem testing. It improves control during the testing operation and gives a more accurate evaluation of the fluid recovered while providing additional pressure information for reservoir analysis. The tools are operated entirely by up and down motion of the drill stem. This up and down operation provides a positive means of control and offers easily observed surface indications of tool operating position. An unlimited number of shut-in and flow periods may be taken with this tool while in the hole. The key to the success of the MFE system of tools is the safety seal packer. Until this development, operation of the tools by up and down motion only had proven unreliable. The success ratio of the MFE now exceeds the ratio achieved by conventional tools. The equipment includes a 2,750-cc chamber in which a representative sample of the flowing formation fluid is trapped at the end of the last flow period and brought to the surface under pressure. The sample can be evaluated at the wellsite or transferred under pressure for laboratory analysis. The sampling feature of the tool allows a sample to be obtained from a reservoir which has suffered minimum influence from production. A representative sample can be obtained for laboratory or empirical analysis by employing a testing technique to minimize drawdown during flow periods. Interpretation methods to take advantage of this additional information are presented and supported by actual field examples. INTRODUCTlON The Multi-Flow Evaluator (MFE) represents the most recent technical advance in formation testing. Drill-stem testing techniques prior to the MFE have been limited in three areas—(1) operaiion, (2) recovery analysis, and (3) reservoir analysis. The tools in the MFE system allow maximum control during testing and provide test information superior to that obtainable with conventional tools. The system of tools and the operation procedures are described to illustrate the mechanical advantages over present tools. Methods of pressure build-up and fluid

Jan 1, 1966

THE solid nonmetallic inclusions that are present to some extent in all commercial steels have been variously designated. In early references they were usually called slag inclusions, and. this terminology is still retained to some extent. On the premise that all nonmetallic matter produced in a metallurgical process is slag, this can be justified. We have come to think of slag, however, in a more restricted sense, and calling these particles slag inclusions is further objectionable because it fosters the erroneous concept that they are actually incorporated portions of furnace slag. Rarely is this true. The term sonims (coined from solid nonmetallic impurities) was proposed many years ago but never came into common use. In general the term "nonmetallic inclusions" seems to be satisfactory and adequate. NATURE AND CONSTITUTION OF NONMETALLIC INCLUSIONS From the standpoint of origin, inclusions fall naturally into two classes: (1) those that occur as a result of reactions taking place in the body of the molten or solidifying metal and (2) those that result from the mechanical incorporation of refractories or other materials with which the steel comes in contact. The former are by far the more numerous and have been called indigenous, natural, or native inclusions. The latter are by their very nature sporadic in occurrence and have been called exogenous, accidental, adventitious, or foreign inclusions. They are often referred to as the "slag stringer" type, though here also the material is not likely to be furnace slag. Substances Found in Inclusions. Nonmetallic inclusions are composed principally of oxides and sulphidea but carbides and nitrides sometimes play an important role. In the case of indigenous inclusions the reactions by which these particles are precipitated from the molten or solidifying steel may be caused by (1) oxidation such as may occur during refining or during tapping and teeming, (2) deoxidation by added alloys, (3) change in equilibrium constants as the steel cools to the freezing temperature, (4) decreased solubility with lower

Jan 1, 1944

By A. Roberts

This paper reviews progress in equipment design and in the techniques applied to mine lighting in Great Britain. The incidence of the disease miner's nystagmus, which was a major source of concern only a few years ago, has now diminished, largely owing to improvements in standards of lighting in mines. The reorganisation of the coal mining industry, involving increasing mech-anisation, together with new safety legislation, has brought about the widespread use of mains electric lighting underground. An account is given of some of the results of research to determine the lighting conditions needed for compliance with the compulsory legal requirement of "sufficient and suitable" general lighting at specific localities in British mines. Some details are given of the techniques applied and the results of recent research in the problem of glare from miners' cap lamps. Of the various factors in the working environment of the miner, it is true to say that lighting is seldom given attention comparable with that devoted to other factors, such as dust, heat and humidity, or atmospheric gas content. No doubt one reason for this lies in the ability of the human eye to adapt itself to low brightness levels. Be that as it may, the fact is that at the turn of the 20th century the miner's working light improved little throughout the centuries during which mining technology has developed. Indeed, in coal mines which encounter a methane explosion hazard, flame safety lamps, with a luminous intensity less than one candle power, were virtually the sole means of lighting during almost the whole of the 19th century. The 20th century has witnessed a substantial improvement in lighting techniques underground in coal and metalliferous mining. In Great Britain the general pattern has been one of standards periodically raised by the implementation of Statutory Regulations imposed under successive hlines Acts, but it is fair to add that the more progressive mining companies usually anticipated the Statutory Regulations, which when they have been put into effect have served to turn into general practice what was already being done at the better mines. In earlier years, official requirements were limited to the specification of approved lamp designs, with stipulated minimum values of luminous intensity and light output, but more recently the necessity of satisfactory maintenance of standards during service has been recognized, and the current regulations not only require that a maintenance organisation should exist, but also specify a maximum permissible depreciation below initial approval standards.'

Jan 1, 1961

By John W. Cahn, David A. Karlyn, Morris Cohen

The massive B(bcc) — am (fcc) transformation in Cu-Zn alloys has been studied isothermally by pulse-heating the retained ß phase from room temperature to the reaction temperatures. The transformation is found to occur only in the single-phase a region of the equilibrium diagram. The massive growth rate is of the order of 1 cm per sec and is constant at each temperature, usually after a delay time of some milliseconds. The delay time depends on the reaction temperature in C-curve fashion, while the growth rate increases monotonically with temperature over the single-phase range. The absence of isothermal massive transformation in the two-phase region does not arise from slow growth rates at such temperatures, but because the reaction cannot get started there. It is proposed that the massive transjormation initiates at small preexisting a particles which have rejected zinc into the surrounding 0 matrix. Only within the single-phase region can these particles consume the excess zinc during diffusion-controlled growth and thereby accelerate to the steady-state massive growth rate. The onset of massive growth marks the end of the delay time, and the growth rate then becomes interface-controlled. These isothermal transformation characteristics explain why the usual composition range for massive-kinetic studies by quenching is so limited. The same principles can be extended to more complex alloy systems by recognizing that the single-phase region in which the massive transformation can occur may not be stable with respect to phases not participating in the reaction. MASSWE transformations are now recognized as a regular class of solid-state reactions involving no compositional change (like martensitic transformations) and no shear displacements (unlike martensitic transformations). The name was first coined by Greninger1 in 1939 to describe the coarse grains of fcc a solid solution generated via a fast reaction from the parent bcc 0 solid solution in Cu-A1 alloys. However, some 9 years earlier, phillips2 had already described a similar transformation in the Cu-Zn system. The fact that the massive a formed as a single phase during drastic quenching from the 0 region of the equilibrium diagram signified that compositional changes were precluded. and the reaction was presumed to take place as in a one-component polymorphic transition by nucleation and growth. Phillips also observed that the occurrence of the massive transformation in the Cu-Zn system was extremely sensitive to alloy composition. For example. in a Cu-37.3 at. pct Zn alloy. the ß — am (am = massive transformation product) reaction was found to predominate and was not suppressed by iced-brine quenching from the 0 region. whereas at compositions greater than 38.3 at. pct Zn the massive reaction did not appear at all. Knowledge concerning massive transformations has bee11 substantially enhanced over the years by Massalski and his coworkers; an excellent summary of his papers and the current understanding of this type of reaction has been published recently by Barrett and ~assalski." he massive transformation product grows in roughly nodular form. often with irregular boundaries but sometimes with almost planar interfaces. The latter may have simple crys-tallographic indices relative to the 0 matrix. or the indices may be complex just as in the case of mar-tensites.'1 Little is known about the existence of orientation relationships between the massive and parent phases. A striking feature of massive transformations is that the massive units start almost exclusively at grain boundaries of the parent phase and frequently propagate on a broad front across matrix grains and grain boundaries of various orientations. Because of the rapid growth rate, it is thought that the interface motion is controlled. not by long-range diffusion. but by thermally activated atom jumps across the transformation boundary.

Jan 1, 1970

By Ott F. Heizer

The mines and the mill of the Nevada-Massachusetts Co. are on the east slope of the Eugene Mountains, in Pershing County, Nevada, 8 miles northwest of Mill City, a station on the Southern Pacific R.R. and on the Victory Highway. Fig. 1. Supplies and, concentrate are transported by truck over an automobile road of easy grade. The property is at an average elevation of 5500 ft. and climatic conditions are generally favorable for continuous operation throughout the year. The ore treated is supplied by two adjoining mines, the Stank and the Humboldt. Physical and mineral characteristics of the ores produced by these two mines are substantially similar, although variations occur in hardness and mineral distribution.' The economic mineral is scheelite (CaWO4), composed, when pure, of 80.6 per cent tungstic trioxide (WO3) and 19.4 per cent lime (CaO).

Jan 1, 1935

By Jerome F. Kuzmick

INTRODUCTION THE use of iron powder during the post-war conversion period has been increasing with great rapidity. This is particularly true in regard to the manufacture of molded mechanical parts such as bushings, gears, cams, small wheels, and the like. Many manufacturers have found it possible to replace machined cast iron and carbon steel with molded iron powder parts, and thereby can not only effect a savings in cost, but can produce a better product as well. As the field of application for iron powder parts widens, greater demands are made upon the powder supplier concerning quality and uniformity characteristics. The following are some of the most important properties parts fabricators desire in the iron powder they use: I. The powder should have high compressibility so that good density can be obtained without the use of excessive pressures. At the same time, it should show low die wear so that a large number of pieces can be produced from the die. This means that the powder must be of high purity and good softness or plasticity. 2. The powder should produce compacts of high green strength, so that unsintered parts can be handled without breakage or fraying of the edges. 3. The sintering properties should be good so that satisfactory strength is obtained in the sintered piece. 4. Compacts made from the powder should show small but, above all, uniform dimensional changes during the sintering operation so that accurate parts can be produced, and warping and other such bad effects eliminated. 5. The powder should have satisfactory flow properties for automatic molding. 6. It is very important that the powder be uniform in sieve analysis, compressibility, flow, purity, and other qualities, from container to container in any given lot and from shipment to shipment. 7. Price-The fabricators desire all these good properties, but in many instances still do not wish to pay a premium price. There has been considerable discussion as to the importance of price of the powder in relation to the cost of the finished product. It is true that in cases where certain special properties only procured by powder metallurgy are required, price is not a criterion. On the other hand, there have been a number of applications recently made which would not be commercially practical with a powder which commands a premium in price. Iron powder parts are compressed in automatic presses to definite size, shape, and density. The powder is compressed to a density figure dependent upon the function the part is to perform, as well as upon such important considerations as press capacity and die wear. Such parts can be roughly broken down into the following density ranges:

Jan 1, 1948

By J. H. Bain, D. C. Haigh, L. C. Parsons

Jan 1, 1964

By Lucien F. Trueb

The microstructure of explosion-bonded pairs of similar and dissimilar metals has been investigated by electron microscopy. A review of the specific problems encountered and the methods used for obtaining surface replicas and thin-film transmission specimens of the bond interface is given. The bond area is mainly characterized by continuous and practically diffusionless metallurgical bonding. The very large shear stresses induced along the collision front of the plates being joined causes extreme grain elongation and a symmetrical pattern of subgrains in the bonding direction. The bond zone is also characterized by a very high density of dislocations and pressure-induced twins. Localized heating occurring during the cladding process can result in partial re-crystallization or the formation of thin layers of molten material. The force of precisely controlled explosions causing a high-velocity impact between metal plates has been used for several years to achieve metallurgical bonding between an extremely wide variety of metals. This method essentially consists of accelerating a plate to high velocity toward a stationary plate by a detonating explosive. Since the restrictions to bonding are not those encountered with conventional nethods, it becomes possible to bond pairs of metals having widely different mechanical properties that are immiscible or form brittle intermetallic compounds. Many applications of such composite metals are found in the field of corrosion protection as well as numerous other fields; for example, explosion bonding is being applied for fabricating the materials used by the United States Mint in the new sandwich-type coins. The primary condition for establishing a metallurgical bond is that absolutely clean metal surfaces be brought together. Any metal exposed to the atmosphere is covered with oxides, adsorbed gases, and other contaminants; even a very forceful impact of two such surfaces is not sufficient for bonding. Cowan and Holtz-man,"' who reviewed the dynamics of colliding plates in detail, showed that in order to achieve a good bond the explosion conditions must be chosen in such a way that the plate collision velocity is less than the sonic velocity, in which case no oblique shock waves are attached to the collision front. A pressure wave is then generated ahead of the collision line, and the material forming the colliding surface of each of the plates flows forward and is ejected in the form of a spray, the so-called jet. The dynamic elastic limit of the metals must be exceeded so that there is sufficient plastic deformation. At the point where the jet formed by the junction of the inner surface layers of both plates separates from the combined plates, the material experi- ences a very high shearing strain and the pressure can reach several hundred kilobars. This process strongly influences the microstructure of the bond zone as will be seen later. Behind the collision front, uncontami-nated layers of internal material are brought together under high pressure and are thus metallurgically bonded. I) STRUCTURE OF EXPLOSION BONDS The different types of explosion bonds that can be obtained depend on the explosion conditions, and have been investigated by Cowan and Holtzman,1'2 Holtzman,3 Klein; Bahrani and crossland,' and Buck and Horn-bogen. The preferred kind for practical applications is the so-called wavy bond, typical examples of which are given in Fig. 1 showing light micrographs of various metal-to-metal interfaces. In forming this type-- of bond the collision energy is mainly expended in jetting, the formation of waves, and localized melting. Beyond the crest of the waves, eddy-shaped areas are observed in which the two metals are mixed in a complex pattern of streaks. Cowan and Holtzmanl first proposed that this wavy pattern is analogous to periodic eddy shedding in the flow of a viscous fluid around an obstacle (Von Karman's eddy street). The mass of metal ahead of the stagnation point, which is associated with the jet and has forward momentum, plays the role of an obstacle and the eddies created in the flow of solid metal around the stagnation point are preserved in the final clad specimen. This idea has been reviewed more recently by Klein4 and the variables involved in the wave formation have been discussed in some detail by Bahrani and crosslands and Buck and Hornbogen.6 Several studies of the structure of explosion bonds by light metallography have already been published.1-6 Aside from the waviness and the eddies which were mentioned above, the most striking characteristic of the area in the vicinity of the bond interface is a very considerable longitudinal grain deformation which appears to be strongest at the metal-to-metal boundary and dies out as one moves away from it. Large twins are often observed within the deformed grains, and molten areas are found in the center of the eddy-shaped structures situated beyond the crest of the waves. The large hydrostatic pressures and shear stresses occurring at the interface modify the mechanical and chemical properties of the bond zone. Increases in hardness in this area have been reported by various authors.396 The defects along the interface can also cause a local increase of the chemical reactivity and thus might be expected to boost the etching rate. However, the effects of this preferential etching cannot be observed by light microscopy due to its inherently limited resolution power. The same limitation precludes the observation of morphological features directly along the bond interface as well as the interface itself. Furthermore, no information can be gained by light-

Jan 1, 1969

By G. M. Schwartz

THERE has been considerable controversy regarding the structure and mineral constituents produced when iron ore is sintered. This investigation was undertaken in order to establish the fundamental reactions that take place in the sintering process by determining the nature of the resulting minerals. The writer's immediate interest in the subject arose mainly from the request of E. W. Davis for information based on a microscopic study of sinter submitted by him in May, 1926. In the author's preliminary work, samples of iron-ore sinter were secured from the Minnesota School of Mines Experiment Station and from commercial plants. These were polished by the usual methods for polishing opaque ores. In order to study these surfaces satisfactorily, it is necessary to magnify them rather highly, a range from 100 to 1000 dia. being used. For the higher magnifications oil-immersion lenses and an intense source of light are necessary. After the preliminary study had shown the problems involved, a series of small samples were sintered under carefully controlled conditions and with analyzed materials. Variations in the relative amounts of ore, coal and water were made in order to study the effect of each constituent. The attempt has been to arrive at a clearer understanding of the sintering process and the reactions involved without reference to any preconceived notion as to sinter. It is clear that the study of polished surfaces has yielded results not possible with thin sections alone. The thin sections made in this work were found unsatisfactory at magnification greater than 75, whereas magnifications of 1000 were easily studied with reflected light on carefully polished surfaces. A rather complete statement of observed facts is made so that the reader may form his own conclusions. The writer's interpretations are suggested.

Jan 1, 1929

By AIME AIME

HOWARD H. PRESTON, professor of economics and business at the University of Washington, presented a paper before the North Pacific Section, A.I.M.E., on Jan. 23, on the "Economic Aspects of Gold and Silver." He carefully reviewed recent governmental actions that have affected those metals and gave an interpretation of their effects. A brief excerpt from his address; follows: Including the proclamation of March 6, 1933, the principal steps of the present Administration which have carried the United States off the gold standard and led up to the present program have been: (1) The Presidential proclamation of March 6 controlling gold. (2) The monetary sections of the Emergency Banking Act of March 9. (3) Mobilization of gold under Executive orders issued March 10 and April 5. (4) The gold embargo by Executive order, April 20. (5) The controlled inflation bill, May 12. (6) The joint resolution abrogating the gold clauses, June 5. (7) The Executive orders on newly mined gold, Aug. 28. (8) The President's radio address of Oct. 22 and the R.F.C. gold-buying program. (9) New anti-hoarding order calling in small holdings of gold, Dec. 28, 1933 and Jan. 15, 1934. (10) Nationalization and revaluation of gold' (Message to Congress, Jan. 15).

Jan 1, 1934

By R. Costantini

The author discusses the promising future of the use of pipelines for transportation of ore slurries over long distances, citing existing installations. Various criteria and factors affecting the use and size of pipelines are considered. Among the factors influencing the use of pipelines are particle size, specific gravity, abrasiveness, minimum velocities, and pumping considerations. Long-distance transportation of solids by hydraulic pipelines holds the promise of great economic benefits. Today within the confines of most mineral processing plants, the moving of solids about in slurry form by pipeline is commonplace, since the method offers great advantages when conditions are suitable. Yet, this method is surprisingly slow in being adopted on a broad scale for transportation of solids over long distances (arbitrarily the term will be applied to one over five miles long). This is especially surprising in view of the successful realization in this country within the last five years of two daring ventures in long-distance solids pipelines. A 72-mile long, 6-in. diam pipeline of the American Gilsonite Co. has been satisfactorily transporting 700 tpd of gilsonite from the mine at Bonanza, Utah, to the processing plant at Grand Junction, Colo., since April 1957. The 108-mile long 10-in. diam pipeline of the Pittsburgh Consolidation Coal Co. has been transporting about 4000 tpd of finely crushed coal from the mine at Cadiz, Ohio, to the Eastlake power plant of the Cleveland Electric Illuminating Co. on Lake Erie since January 1958. However, besides two projects in the operations of The Anaconda Co. there have been hardly any other significant solids pipeline developments in the minerals industry during the last three years. The two projects are the 14-mile long, 6-in. diam copper concentrate gravity pipeline at Anaconda's El Salvador project in Chile which has been transporting about 800 tpd since January 1959. The second is a 16-in. diam tailings pipeline at the Anaconda Reduction Works, Anaconda, Mont., designed to transport about 20,000 tpd of deslimed flotation tailings for dam building. This pipeline, which is currently undergoing tryout tests and which will be about seven miles in length, will have a maximum of three 20-in. rubber-lined centrifugal pumps in series at the starting point, each developing a maximum of 100 ft of head, to supplement gravity. It is the writer's opinion that the major reason for the hesitation in considering pipeline operations is confusion due to an inadequate understanding of the basic physical principles affecting the slurry flow process by many engineers in the industry. This in turn begets an attitude of fear and trepidation instead of confidence on the part of many management executives, which leads to a minimizing of the advantages and exaggeration of difficulties when considering the possibility of a long-distance solids pipeline. The promotion of better understanding and consequently the promotion of greater confidence in the potentials of long-distance solids pipelines when conditions are suitable is thus the main purpose of this article. To this end, after considering several examples of the possibilities for solids pipelines in the minerals field, the relative significance of the major factors affecting pulp flow, and some major aspects of slurry pumping will be discussed on a general qualitative level. Then a brief outline of the semi-empirical quantitative methods developed to date for estimating slurry flow behavior will be presented. SOME POSSIBILITIES To give an idea of the magnitude of the possible economic benefits, it should be interesting to mention briefly some of the projects currently under consideration and to suggest some likely future possibilities. At Anaconda's El Salvador Project in Chile (Fig. 1) it is eventually planned to extend the existing 14-mile pipeline by another 60 miles to bring the copper concentrates down to the coast of the Pacific Ocean. Preliminary tests indicate that the projected 6-in. pipeline will be able to transport approximately 2000 tpd of concentrates at a pulp density of 40 to

Jan 1, 1961

By Richard E. Chism

Jan 1, 1902