Search Documents

By R. J. Matetic

The Bureau of Mines, as part of a program to improve mine planning and development, is currently investigating the effects of pillar load transfer, which can impact mining operations wi.thin a multiple-seam configuration. At two mine sites where such ground interactions were present, the Bureau performed a complete geological analysis and installed and monitored instrumentation to gather pertinent data on rock mechanics. Overburden depth varied dramatically in the vicinity of the study area and reached a maximum at the study site; innerburden thick-ness was less than a pillar width (40 to 4S ft); heaving was experienced in both mines where sandstone and/or shale floor units were observed; overlays of the mine layouts show pillars were not totally superpositioned; a maximum of S in of roof to floor convergence was measured; and pressure readings indicated pillar core loading only and increased to a maximum of 7,000 psig over instrument setting pressure.

Jan 1, 1987

By S. Malhotra

Processes for the recovery of manganese contained in low-grade domestic sources are evaluated. Conclusions are based on analysis of literature, technical evaluation and cost analysis. The Nossen Nitric Acid Process, the Sulfuric Dioxide Process rind the Ammonia Leach Process should be developed further as they offer the hunt opportunity for commercialization.

Jan 1, 1984

By J. A. Kost

The objective of Contract J0295041 was to determine if the addition of a surfactant (wetting agent) to the water used for dust control in underground coal mines results in the reduction of airborne dust. Laboratory wettability tests, including the capillary rise test, a coal dust sinking test and zeta potential measurements, were used to select a coal seam/surfactant combination for in-mine testing. Four surfactants were selected for underground testing: Surfynol 465, Aerosol MA-80, DC-13, and Dustallay. The underground tests in the Lower Kittanning seam, Indiana County, PA, involved a Wilcox Mark 20 auger mining system, equipped with spray nozzles located on the cutting augers, Conflow venturi sprays, and a spray manifold. Respirable dust samples were provided by MSA Model G personal samplers and Simslin II instantaneous dust monitor; total airborne dust samples were provided by MSA Model G samplers with UNICO filter cassettes. Based on data obtained from 24 test periods surfactants, as compared to plain water, reduced the airborne respirable dust an average of 27 percent and total airborne dust an average of 36 percent.

Jan 1, 1980

By Dana T. Updyke

The objective of this project was to develop technical data and evaluate performance and utility of leaky feeder communications systems currently used in North American underground mines. The desired information was obtained principally through on-site surveys. Altogether, six of the seven mining companies known to be using leafy feeder communications were visited. This report covers the findings of these surveys. In addition, the report provides a brief background summary of mine communications, a technical discussion of leaky feeder systems, and conclusions and recommendations based on the results of the survey.

Jan 1, 1980

These proceedings consist of papers presented at two Bureau of Mines Technology Transfer Seminars for the purpose of disseminating recent advances in mining technology related to coal mine fire and explosion prevention. Primary, although not exclusive, emphasis is placed on underground coal mining. The papers address research accomplishments ranging from methods for detecting mine fires to remote sealing systems for extinguishing coal mine fires. Each paper represents the current state-of-the-art in the respective research categories. Presentations include research occurring from both Bureau in-house and contract efforts.

Jan 1, 1978

This report presents the results of studies of Kennecott Copper Corporation's tailings embankment at Magna, Utah. The stability studies described were performed on only one cross section of the embankment, utilizing; data obtained from drilling, sampling, and testing, which was limited in nature. The main objective of the data collection was to provide background information to support the overall research effort. Because of this limited scope, it is not possible to evaluate the degree of safety or adequacy of the embankment or disposal system, and the information and data contained in the body of this report must be judged in that light. The first part of this report contains discussion of site geology and seismicity, pertinent information on the refuge disposal system, a discussion of the tailings materials characteristics, a summary of the engineering analyses, and A bibliography. The second tart (appendices) contains basic geologic and engineering data supporting the discussions in the first part of the report.

Jan 1, 1974

By Roger L. Baer

Marine disposal of mill tailings has been practiced worldwide for over a century. However, only recently have the environmental effects of marine disposal been systematically studied. Some early attempts at marine disposal of tailings resulted in adverse impacts to marine life. However, recent advances in tailings disposal methods have included the introduction of engineered submarine tailings discharge systems, advanced environmental assessment and monitoring methods, and oceanographic modeling systems. Successful submarine tailings disposal (STD) has occurred at several mines. The U.S. Bureau of Mines (BOM) has undertaken studies of the disposal of mining and milling wastes in the marine environment. The BOM Alaska Field Operations Center, Juneau, initiated a review of the technology, regulations, and economic aspects of STD. The review illuminated the need for organization of literature on the subject, therefore the Bureau compiled this extensive bibliography on marine disposal of mill tailings. The bibliography presented here contains 1483 references and is also available through diskette in the Word Perfects format. A review of the references indicates that literature on submarine disposal inadequately covers the subject. The majority of the references listed only peripherally relate to the subject. Published literature on the engineering and environmental aspects of STD is severely limited.

Jan 1, 2011

By William C. Cooley

A technical and economic study was made of the feasibility of establishing an underground hydraulic coal mine in the Wilkeson-Carbonado coal field approximately 25 miles southeast of Tacoma, Washington. The deposit contains reserves of more than 200 million tons of generally high quality metallurgical coal. It is located in nine seams of minable thickness in a complex, folded and tectonically disturbed set of anticlines and synclines. Typical dip angles are up to 60°, with minable seam thicknesses of 6 to 17 feet. A mine plan was made for a 2 million TPY mine (clean) using two shafts to access the deposit to a depth of 2500 ft. The mining method uses monitor jets to break coal by sublevel retreat mining, fluming to a sump and pumping the minus 0.25 inch coal to the surface and to a preparation plant. The plus 0.25 inch coal is hoisted by skip. Cleaned met coal would be shipped by rail for export. A middlings product would be sold as thermal coal. Assuming a coal price of $48 per short ton (FOB the mine) for the met coal and $35 for the middlings, the return on investment is estimated at 20% after taxes. The many uncertainties about the geological conditions and the specific mine design parameters make the economic analysis and conclusions somewhat tentative. A second mine could also be developed in the eastern section of the reserves to produce 1 million TPY of clean coal and is expected to have similar economics. Recommendations are made for a Test Mine and a Pilot Mine leading to a production mine.

Jan 1, 1983

By Eric E. Unger

Results are presented of a census of the machines used in surface coal mines in the United States. The numbers of each machine type and model reported to be in use are tabulated for large and small mines in the Eastern, Central, and Western regions. Also tabulated are the average daily usage times of the major machine categories and the numbers of machines that have acoustical and other cabs. Projections of the total numbers of primary production machines are given. It is found that heavy tracked dozers and wheeled front end loaders constitute the most prevalent machine types, and that generally a very few models of machines made by one or two manufacturers constitute a major fraction of the population in each machine category. About 70 percent of all machines are reported to have some kind of cab, and about half of these are reported to be acoustical gabs; it is noted that acoustical cabs generally came into significant use since about the early 1970's. It is observed that the percentage-wise mixes of equipment types used in the various categories of mines differ significantly for only a few types of machines, notably for heavy dozers and loaders, and for haulers, highway trucks, and internal-combustion engine-powered shovels and draglines.

Jan 1, 1977

By Wilbert J. Huff

The organization of the Explosives Division has been outlined in two preceding publications., The activities of the various units for the fiscal year 1939 are described hereafter: I. INFLAMMABILITY OF GASES AND VAPORS DETERMINATION OF EXPLOSION HAZARDS OF COMBUSTIBLE GASES AND VAPORS IN MINES AND INDUSTRIES (a) Determination of Limits of Inflammability of Gases and Vapors The following hitherto unpublished limits of inflammability were determined during the past fiscal year.

Jan 1, 1939

By S. J. Rodgers

This report presents guidelines on methods of dust control in conventional coal mining operations. The normal mining cycle and equipment used in a room and pillar conventional section are described. Main ventilation, section ventilation and face ventilation are discussed in detail. Proper installation of line brattice, maintenance of proper air flows at the face and split ventilation are stressed. The effects of maintaining the end of the line brattice near the face are described. The advantages and disadvantages of blowing and exhausting face ventilation are presented. The use of water sprays on cutter bars and loading machines is described. The design of a nonclogging water spray system developed under a Bureau of Mines contract is presented. Other methods of reducing dust exposure are discussed and include alternative procedures for shot firing and administrative controls.

Jan 1, 1983

By M. Kanefsky

Two channel polarity coincidence and polarity difference statistics are analyzed. The signal, common to both channels, consists of sinusoidal bursts where the exact frequency of the signal is nearly known, but other parameters such as amplitude, phase, and pulse starting time are unknown. The noise inputs are dependent, narrow band, Markov processes. It is shown that the performance depends not only on the signal uncertainties, but on the precise shape of the cross-correlation functions between the noise in-puts. By using two polairty difference statistics in addition to the polarity coincidence statistic, it is shown that the decrease in performance, as well as the cost of hard limiting due to correlated inputs, can be made small.

Jan 1, 1981

By Eric G. Kok

Complying with respirable dust standards is presently a critical problem for many longwall faces equipped with double drum shearers. Results are presented of research performed to increase the quantity and optimize the distribution of the water supplied to the shearer drums to control the shearer operator dust exposure. The effect on the total respirable dust produced by the shearer was also examined. During the research effort, a simple and inexpensive manually controlled valve system was designed and implemented on a shearer to distribute the water supplied to the shearer drums. Research showed that increases in water quantities are beneficial but associated pressure increases may induce respirable dust boilover negating potential advantages. Other essential parameters such as location of shearer operator, outside spray orientation and air quantity were considered in the evaluation.

Jan 1, 1986

By George J. Carter

Data obtained from field and laboratory examinations were used by the Bureau of Mines to evaluate 82 silica deposits in the Pacific Northwest. A total of 94 field samples was taken from 64 deposits, and an additional 18 deposits were investigated that did not warrant sampling. Of the 37 deposits found to be of high quality, only 16 were large enough to be classified as industrial silica resources. Another 27 deposits did not meet quality requirements. Methods of simple low-cost beneficiation and rapid classification of a large number of samples were investigated in the laboratory. These tests indicated that high-intensity electromagnetic separation was equal or superior to either high-or low-intensity electrostatic separation. In general, the electromagnetic method gave higher recoveries and produced equal or better grade concentrates. A glass button method developed for estimating iron oxide content of silica samples proved to be highly satisfactory as a means of classifying field samples and evaluating beneficiation tests.

Jan 1, 1962

By Wilbert J. Huff

The organization of the Explosives Division has been outlined in two preceding publications.3/ The activities of the various units for the fiscal year 1939 are described hereafter: I. INFLAMMABILITY OF GASES AND VAPORS DETERMINATION OF EXPLOSION HAZARDS OF COMBUSTIBLE GASES AND VAPORS IN MINES AND INDUSTRIES (a) Determination of Limits of Inflammability of Gases and Vapors The following hitherto unpublished limits of inflammability were determined during the past fiscal year.

Jan 1, 1939

By Fathi Habashi

"Crushing and grinding of ores and their beneficiation by washing away gangue minerals has been practiced since ancient times. Primitive crushing was done by hand pounding the ore with a hard stone then by using metallic hammers. The mortar and pestle was mechanized using a lever and when the size of operations increased in the middle ages, the stamp mill was introduced. The grindstone played an important role in grinding of ores. Panning for gold and hand sorting of minerals were two old methods of separation, now gave way to modern techniques. Flotation started in the middle of the nineteenth century by using oils to collect the mineral particles and float them on the surface of the aqueous slurry. It was only in the 1920s when it was discovered that organic compounds were affective floating agents. Textbooks written by distinguished engineers such as Rittinger, Rickard, Pryor, Taggart, Richards, Gaudin, and others contributed to the recognition of this field as a new discipline to be taught in Universities. INTRODUCTIONThe ancient Egyptians knew already that it would be easier to melt an earth rich in gold particles than another which is poor. As a result all efforts were made to enrich the gold by washing away the light gangue minerals (Figure 1). Another ancient method for enriching gold particles from a river stream was by means of fleece, hence the Greek myth of the “golden fleece”. The present day Georgia was known in ancient times as Colchis and was a center for gold working. It was known to the ancient Greek as the land of Golden Fleece. The use of special cloth to catch gold particles was also described by Agricola in his 1555 book De Re Metallica (Figure 2)."

Jan 1, 2009

By Warren W. Krech

Rock property data is needed over a wide range of parameters for the optimum execution of rapid excavation research. Eight rock types were chosen by the Bureau of Mines for a standard rock suite for such research. Large rock blocks were quarried and the standard physical and mechanical properties measured and documented. The eight rock types that comprise the rock suite are Barre Granite, Berea Sandstone, Dresser basalt, Holston Limestone, Salem Lime-stone, Sioux Quartzite, St. Cloud Gray Granodiorite, and Westerly Granite. Geologic, petrographic, physical-property, and mechanical-property test data are reported for each rock type. The information is the first step in the building of a comprehensive property listing for the eight rock types. A limited number of rock cubes are available from the Bureau of Mines Twin Cities Mining Research Center for use by researchers to broaden the information available on the suite.

Jan 1, 1974

By Fred P. Giese

Southeastern reserves of titanium ores are large, widespread, and ample for anticipated demand. The leading titanium industries are mining and beneficiating sand deposits, principally in Florida, and manufacturing titanium pigments. Most of the mineral output is consumed by the producers themselves. In 1962, 20 percent of the national pigment capacity was in the Southeast.

Jan 1, 1964

By Wils L. Cooley

Although electric utility companies have been active in grounding and bonding within substations, the mining engineer or mine electrical engineer is not involved to the extent that he can be fully up-to-date on the most effective practices for substation construction. The coal mine power system is grounded in a fundamentally different way from most other industrial power systems and is subject to considerable Federal and State regulation. At this time, there is little information that is directly applicable to the mine situation, especially if the substation must be built in an area of limited size or in low-conductivity earth. The objective of this guide is to provide specific engineering information to the mining; industry. Using as little theory as possible, it was written to be general enough to cover most substations, but specific enough to provide direct help with each substation. It will attempt to recommend practice that is in agreement with present Federal rules and regulations.

Jan 1, 1980

By William A. Beck

This report describes the loading and transportation practices employed at the zinc-lead mines of The Eagle-Picher Co., Jo Daviess County, Ill., and Lafayette County, Wis. The report also gives a brief history of the Illinois-Wisconsin zinc-lead district and the operations of the company in the area. The diesel-powered, rubber-tired loading and haulage equipment is described and illustrated from the operational point of view only, and an analysis is made of the materials-handling system without going into health and safety Factors. The costs per ton of the various components of mechanical loading, underground haulage, underground crushing, and hoisting for fiscal year 1960 are tabulated.

Jan 1, 1964