Search Documents

By John D. Foulkes

An investigation is made into whether commercially available equipment can be used to engineer effective emergency warning systems for underground coal mines. Discussions with members of the Bureau and the Mining Enforcement and Safety Administration established that the preferred system should operate over the existing Pager Phone twisted pair, and broadcast an audio alarm. Applicable equipments such as voice band tone signaling equipment, alarm sounding equipment, mine telephones and complete alarm systems from over thirty manufacturers are listed. Factors affecting the range over which an alarm could be detected in representative mine situations were studied. These included (a) the subjective masking effects of typical background noise found in mines, such as that due to continuous miners (b) the attenuation of sound in mines (using both a theoretical and experimental results) and (c) the attention-getting qualities of different sound for miners. Audio alarm systems meeting the requirements can be installed and representative systems are described.

Jan 1, 1977

By W. P. Haynes

To evaluate the potential use of battery-powered vehicles, the Bureau of Mines studied the performance of a battery-powered truck propelled by a 9.6 kw dc motor in considerable detail under various driving conditions. Some of the factors investigated were: Gear ratios, payload (1,468 lb maximum), road grade, stops made per mile, and charging time. With the exception of some difficulty with brush wear, operation and maintenance of the truck was generally trouble-free. On range tests carrying an 868-lb payload a distance of about 50 miles at an average speed of about 19 mph in normal driving, the Bureau's battery-powered truck averaged 1.6 to 1.9 miles per ac kwhr input. Stop-and-go tests indicated that prospects for the use of battery-powered trucks in house delivery service within city limits are good; performance of the Bureau truck was sufficiently high for that type of service. The estimated power cost of 2.65 cents per mile while making 10 stops per mile was attractively low from the standpoint of fuel costs.

Jan 1, 1967

By Alexander N. Winchell

"Location: The Menominee district has been described geologically in several units, because the known iron-bearing formations of the larger region are not a really connected. From the commercial and mining standpoint, however, the district em¬braces, all that territory extending from a point about five miles east of Vulcan to a point a few miles west of Iron River, an east-west distance of about fifty miles, and from a line about two miles south of Vulcan to one ten miles north of Crystal Falls, a north-south distance of about thirty-five miles. This area is largely in the State of Michigan, but includes more than two hundred square miles in Florence County, Wisconsin. The chief towns of the district are Vulcan, Iron Mountain, Iron River, and Crystal Falls, in Michigan, and . Florence in Wisconsin. The Wisconsin portion of the district has not produced a large portion of the output of the area.History: The earliest reports of iron ore in the Menominee district were made by J. W. Foster and S. W. Hill, who conducted a geological exploration from Lake Superior to Green Bay in the fall of 1848. It is a remarkable fact that in spite of their plain statements regarding their discoveries, these state¬ments were apparently forgotten for a period of nearly twenty years. Foster states that ""about two miles southeast of the lower falls (of the Twin Falls on the Menominee River) near Sec. 30, T. 40 N., R. 30 W. there is a large bed of specular iron ore associated with the talcose and argillaceous slates. It makes its appearance on the north side of the Lake and can be traced a mile and a half in length and in places is exposed one hundred feet in width."""

Jan 1, 1920

By Hans von Michaelis

The renaissance in extractive metallurgical practices for gold and silver recovery is far from over. This is one conclusion of a three year investigation into innovations in Cold & Silver Recovery by Randol International Ltd. (1981, 1983). The six volume reference report reviews a host of new processes and innovative applications of older metallurgical practices. Some of these were summarized by von Michaelis (1982, 1982a). There are several reasons to expect this renaissance to continue. One reason is the nature of gold and silver deposits. The list of known occurrences of These metals is very extensive. There are literally tens of thousands of prospects but over 99% of these are too low grade, too small or too refractory for a viable operation employing conventional processing.

Jan 1, 1983

By R. A. Friedel

THE UTILIZATION by the Bureau of Mines of infrared and ultraviolet-visible spectrometry in connection with coal research has led to some basic improvements in methods, including a calibration method, a quantitative assessment of infrared spectral energy sources, and the development and perfection of infrared filters and cells. The adoption of a micropipet method to flush organic samples into absorption cells permits the investigation of vapors from organic liquids and the identification of volatile organic compounds. The spectral method has been used to investigate the infrared spectra of metal chelates, the charge-transfer complexing properties of aniline and nitrobenzene, an infrared method for determining the presence of methane in coal-mine air that has been adopted for use in enforcing the regulations of the National Coal Mine Safety Act, and atmospheric pollution including smog and odor-causing oxidation and decomposition of organic materials. Correlation of spectra and structure of organic compounds, particularly aromatics, was studied.

Jan 1, 1966

By Pedro Lilienfeld

This Final Report describes a program whose objective was to design, develop, fabricate, and test an airborne mass monitor for unattended and recording measurements of the concentration of dust in mining environments. Sensing collection are performed by beta-radiation attenuation and inertial implementation respectively. The instrument is portable, battery or line operated provides a digital printout of the mass concentration during each selection sampling period, as well as the accumulated mass of dust, and the elapsed sampling time.

Jan 1, 1974

By Michael W. Redifer

A Fortran IV computer program was developed to calculate the composition at equilibrium of products from a set of high-temperature gas combustion reactions. The program was used to develop high-temperature equilibrium concentration profiles for various constituents as a function of temperature and oxygen concentration. The computer program was specifically applied to reactions pertaining to the corrosion of superheater tubes in pulverized coal-fired boilers; however, it is useful for any multicomponent, multireaction scheme in which equilibrium constant data can be obtained and is comprised of gaseous reactants along with finely dispersed solids or liquids. General applicability of the computer program, including its limitations, are discussed along with detailed instructions for using the program.

Jan 1, 1973

By Thomas A. Mekelburg

Due to a tight ash constraint on the clean coal product and difficult middlings washability characteristics, a considerable amount of coal was being lost in the jig middlings at the Monterey No. 2 Mine. An investigation was conducted into circuitry to recover this lost coal with minimal effect on the total clean coal ash. A reverse two-stage hydrocyclone system cleaning at low specific gravities was selected. This system is currently recovering approximately 5.8 kg/s (23 tph) of 11.5% to 12.5% ash coal. The specific gravity of separation for the system is about 1.5 and the probable error is 0.13.

Jan 1, 1984

By W. R. Hardwick

This Information Circular describes copper mining and concentrating methods, practices, and costs at the Silver Bell Unit of American Smelting and Refining Co., Pima County, Ariz. It is one of a series being prepared by the Bureau of Mines on mining methods, practices, and costs in various mining districts of the United States. The Silver Bell mining district, one of the older districts in Arizona, is in the western part of the Silver Bell Mountains in Pima County, about 40 miles west of Tucson and about 20 miles southwest of Red Rock, a station on the main line railroad of the Southern Pacific Co. The Oxide and the El Tiro open-pit mines of the American Smelting and Refining Co. are in the district (fig. 1. The principal ore deposits are in T. 12S., R.8E., Gila and Salt River base line, at an altitude of about 3,000 feet. The present town of Silver Bell, established in 1952, is reached by a paved highway, the Avra Valley road, that turns west from Highway 84 at Plata siding near Rillito and extends westward 25 miles to the townsite (fig. 2). The present town is about 5 miles southeast of the old town of Silver Bell that flourished from 1900 to 1930.

Jan 1, 1963

By Herty, C. H.

Iron oxide (FeO) plays an extremely important part in the manufacture of iron and steel. In the three major processes- blast-furnace, open-hearth, and Bessemer converter-iron oxide is the chemically predominant compound and controls to a large ex- tent the operation of the furnaces and the composition and quality of their respective products. In order to emphasize the importance of iron oxide in each process, they will be considered individually in some detail. THE OPEN-HEARTH FURNACE. Iron oxide is introduced into the open-hearth furnace in four ways : 1. The scrap charged into the open hearth is oxidized by the furnace gases, the amount of oxide formed depending primarily on the amount and type of scrap charged. It has been found' that with large scrap, 1.7 Ib. of FeO is formed per 100 Ib. of scrap charged, whereas with scrap of medium size about 5.3 Ib. of FeO is formed per 100 Ib. of scrap charged, when the period between the charging of the scrap and the addition of hot metal is 3 hours. 2. The decomposition of the limestone sets free CO, by the reaction

Jan 1, 1957

By John C. Taylor

A resource document, prepared for the Royal Commission on the Health and Safety of Workers in Mines, which outlines aspects of occupational health and safety in the Canadian metallurgical industry has been expanded to provide examples of some practical solutions. General process descriptions are provided in conjunction with some of the major potential hazards associated with each step. Emissions to the working environment, particularly around converters, are discussed. Newer metallurgical processes, the role of automation and other advances in the metallurgical industry are described with respect to their impact on the work place. The role of staff and unit employees in providing safe working conditions in the complex metallurgical plant of today is outlined and the need for close cooperation within the human sector emphasized. The technology is available and is being applied to integrate the complex process requirements with realistic regulations to control emissions and provide a safe, healthy environment in metallurgical plants.

Jan 1, 1978

By Louis A. Panek

Determining the change of stress in rock based on measurements of the deformation of a drill hole is a procedure that is increasing in popularity. A closely related procedure involves the applicat10n of this principle to determine the existing stresses in a rock medium, by cutting free (core drilling) an annulus containing the drill hole. In this Bureau of Mines report, expressions are derived from which one can calculate the stress ellipsoid--the three-dimensional change of stress, or the existing three-dimensional stress field, as the case may be. Study of these equations shows that the stress components in three dimensions can be determined by measurements in only two drill holes, and yields general principles that are useful in planning an efficient program of drilling and measurement. Procedures are given for calculating the least squares estimates of the stress components and their standard errors, and for evaluating or comparing calculated values by means of standard statistical inferences.

Jan 1, 1966

By James W. Wade

This paper describing the mining practices at the Tintic Standard mine is one of a series being prepared by the United States Bureau of Mines. In the preparation of this paper each subject has been presented by the engineer in charge. L. R. Dobbs wrote the part pertaining to tae technique of square-set mining, J. M. Snow the part on geology, and M. D. Paine, the part on ventilation. All of the drawings are the work of H. W. Waterfield of the engineering department. The statistics of the Tintic district ware prepared by A. G. MacKenzie. Each writer has attempted to show the difficulties that arise in operating and the practices used to overcome them.

Jan 1, 1930

By Richard G. Almes

Since the failure of a major coal refuse disposal embankment and impoundment in the Buffalo Creek watershed near Man, West Virginia in early 1972, there have been extensive changes in the design and construction requirements for coal refuse disposal facilities located throughout the United States. The primary emphasis has been on improving the safety of these facilities, particularly for impoundments which are capable of storing millions of gallons of process water and storm runoff. The Mine Safety and Health Administration (MSHA) of the U.S. Department of Labor (formerly the Mining Enforcement and Safety Administration, U.S. Department of interior) has been the lead federal agency in promulgating regulations pertaining to coal waste disposal. In 1974 and 1975, studies were undertaken by our firm under contract to the Mining Enforcement and Safety Administration to prepare a comprehensive engineering and design manual to be used by operators and engineers in the planning and design of coal refuse disposal facilities with the intent ion of avoiding any more Buffalo Creek failures. The resultant 800-page document addresses major subjects such as safety, environmental controls, and cost. Specific topics include characterization of coal refuse, classification of disposal facilities, project planning, geotechnical investigations, testing and design requirements, hydraulic and hydrologic design, environmental factors, operations, and monitoring, instrumentation, and maintenance.

Jan 1, 1980

By Bernard J. Steblay

The U.S. Bureau of Mines has attempted to use ultrasonic signal travel-time measurements to measure loaded roof bolt strains. The strain measurements are then related to roof bolt loads through equations or empirical calibrations. Such techniques offer the potential of accurate, rapid bolt load measurement that does not disturb the anchotage. This report presents 6e research findings for a specific type of ultrasonic measurement instrument using a pulsed-phase-Iock-Ioop technique. This technique measures signal travel time indirectly by measuring frequency changes. A complete development of the applicable theory and detailed derivations of key equations is presented along with empirical laboratory and field results. The differences between anticipated and measured behaviors are analyzed and discussed. The report identifies problems encountered in applying pulsed-phase-Iock-Ioop technology to roof bolt load measurement and provides potential solutions to many of them. A key assumption of pulsed-phase-lock-loop theory is that driving and reflected signal frequencies will always be equal. Findings showed that not only were actual frequencies not equal but they were not stable or simply related. Reflection wave shape also was not stable. The ramification of these findings and ways to minimize their adverse effects are presented.

Jan 1, 1990

By Chas. F. Jackson

During the current business depression the Bureau of Mines has received many inquiries concerning placer mining, the prospects for men of small means to make wages by small-scale placer operations, the locations of placer deposits in the United States, methods of working placers on a small scale, and allied subjects. It has therefore seemed desirable to prepare a circular covering, in nontechnical language, the principal questions which have boon referred to the Bureau of Mines for answer. There are a number of bureau publications dealing with placer mining, most of which are now out of print, but which may be consulted in the larger libraries. Other articles on placer mining nave appeared from time to time in the technical press and several good textbooks have been written on the subject. A partial bibliography of this literature appears at the end of this paper. A recent pamphlet published by the Idaho Bureau of Mines and Geology to assist the prospector and inexperienced small operator has received wide and favorable attention and is recommended as a useful reference. In the present paper no attempt will be made to cover the subject of placer mining in a comprehensive manner, but discussion will be confined to elementary questions of particular interest to persons of limited experience.

Jan 1, 1932

By P. R. Taylor

This investigation (Bowles, 1990) involves consideration of technology utilized by three separate fields of metallurgy and materials science: 1) The recovery of metals employing the use of solvent extraction, 2) The fabrication of materials using powder metallurgy, and 3) The use of composite materials in fabrication of engineering materials. The research considers each of the processes in order to realize the benefits of each. In light of the fact that materials have an intended use -it does seem plausible to simplify the process required between "mother earth" and final use. For instance, a primary copper producer that already employs a solvent extraction and electrowinning process could produce value added products directly. Part of the existing extractant flow could be diverted into a pressurized hydrogen stripping process in order to produce specialty composite powders. Innumerable methods have been employed for the recovery of metals; solvent extraction, the one considered in this study, was used due to the possibility of it providing a pure powdered metal. The use of solvent extraction in the recovery of metals has gained wide acceptance and its use proves beneficial in many applications (Ritchey and Ashbrook, 1984). Pressure hydrogen stripping of solvent extractants may provide the benefit of flowsheet simplification compared to conventional solvent extraction followed by electrowinning. It may also provide the benefit of direct production of high purity metal powder (Demopoulos and Distin, 1985).

Jan 1, 1992

By S. Kraemer

Consumption of plastics has been growing in both the U.S. and world markets since the mid-1930s. This growth is due to plastics being used to make new products and as a replacement material for existing products. This paper develops an understanding of the replacement process by looking at the use of plastic, specifically PVC, in the construction pipe industry. History details the growth of the plastics industry and a discussion of the material selection process indicates the advantages and disadvantages of plastic pipe. Analysis shows that the use of plastic, as an alternative material for pipe, is having a significant effect on the cast iron, copper, clay, and steel industries. For the purpose of understanding the replacement process, three example residential systems were examined with a lifecycle cost analysis being performed. PVC was the material of choice in 1988 for all systems. Even though disposal cost was the one area where PVC was not the most cost effective, disposal costs were not sufficient to offset the overall advantage of using PVC on an economic basis. That plastic competes effectively with other materials, in terms of material properties and cost, indicates that further work should be performed to understand the impact plastics have on other material markets.

Jan 1, 1991

By Ken Hester, Bruce Arthur

"Introduction""Pebble milling"" is a term used to describe secondary grinding done with rock pebbles rather than steel balls or other steel or metal shapes. This paper discusses pebble milling with particular attention being paid to uranium grinding circuits.Pebble milling is typically employed:a. where the cost of steel balls becomes exorbitant, as may be the case in an isolated area.b. where the extra steel added from steel ball consumption may be detrimental to further processing.c. where the over-all economics favour the use of pebbles rather than ball.Pebble milling differs from autogenous and semi-autogenous grinding in that a sized product has been removed from some part of the primary comminution circuit, and it is this sized product which is added as grinding media to the pebble milling stage. The pebbles do not necessarily have to be produced from the ore- ""foreign"" pebbles can be used. Also, pebble milling generally refers to grinding from a fine size, below about 6 mesh (3360 micron), with relatively small media, that is, secondary grinding. In South Africa, however, primary pebble mills are sometimes used to grind crusher house product, and thus function in place of rod mills. Pebbles for this service are large and heavy as they must weigh as much as balls used in similar service.The first large applications of pebble milling were in South Africa(n. ""Tube milling"" with pebbles started in 1904. The tube mill was simply a tumbling mill with a length to diameter ratio over two. A ""typical"" early tube mill was 5.5 ft. (1.7 m) in diameter and 16 ft. (4.9 m) in length. Diameters increased steadily. King(n mentions 8-ft. (2.4 m) units in his 1949 book. By 1961, the largest units discussed by Jackson('' were 12ft. (3. 7 m) in diameter."

Jan 1, 1989

By Richard H. Mote, W. C. Schroeder

The endlessly changing pattern of mineral supply and demand offers opportunity to the alert and can bring disaster to the unwary. The discovery of ore bodies, the invention of extractive processes, the provision of new transport facilities, the political stabilization of underdeveloped areas, and many other changes can increase supply dramatically. Such new outpourings of mineral wealth from ore bodies bring fortunes to their developers, and consumers frequently find their competitive positions decidedly improved by new and cheap sources of supply. On the other hand, operators of marginal properties can find competition from newly opened high-grade mines intolerable. Consumers that have depended on the products of nearby, high-cost mines may find new, remote, low-cost supplies advantageous only to their competitors. The invention of new prospecting methods can have spectacular effects. Shortly after World War I the discovery rate of petroleum pools began to decline. The leading prospecting technique of that day, the projection downward of surface reflections of geologic structure, was proving less rewarding. Prophets foretold an oil shortage in the near future. But at that very moment scientists were perfecting the application of seismic waves to reveal underground oil-bearing geologic structures. As these geophysical methods were put into commercial use the whole outlook changed-the problem of the 1930's became how to cope with the surplus from discovery, not how to meet the ever rising demand. Many lead mines were being abandoned as unprofitable about this same time because the penalties charged by smelters for the zinc in the ores and concentrates more than counterbalanced the payments for lead and silver. Then selective flotation (at the time called differential flotation) appeared,

Jan 1, 1959