Search Documents

By Wilbur L. Webb

This publication reports on the design, fabrication and test of an Improved methane monitor system for compliance to 30CFR75.313. The system will Initiate automatic shutdown of mining machinery when excessive concentrations of methane are encountered. The prime consideration: In the design were small size, Improved accuracy and reliability, fast response and a transient resistant power supply capable of reliable operation from any mine power source. The power supply contains an internal battery that provides operating power to the detection system prior to mining machine start-up or after machine shutdown. This report documents the development program from conception through in-mine testing.

Jan 1, 1978

By Dean H. Ambrose

[Mining and processing earth's materials form the basic building blocks from which many technology advancements and products are made. Virtually all metallic and non- metallic products are derived from a substance found in our earth that we blend, mold, extrude, or pulverize into something useful, the mining industry is responsible for the first step of this process: extraction from the ground. Mining particularly coal mining. poses significant risks to both humans and machines. As raw materials are]

Jan 1, 2009

By J. A. Pile, Virgil Miller, R. G. Peterson, F. B. Petermann

"INTRODUCTION As virtually no published data are available on the sintering of fine, minus-100-mesh, ferrograde manganese ores, it is most opportune to present data on the amenability of various fine ores and mill products to the sintering process. These data cover the sintering or nodulizing of finely crushed, high-grade pyrolusite and rhodochrosite ores, sintering of manganese carbonate flotation concentrate, sintering or nodulizing the calcine from the deleading of a manganese oxide flotation concentrate, and sintering the calcines made in a Herreshoff furnace from the treatment of manganese sulfate products.If finely sized products are to be smelted in the present electric or blast ferromanganese furnaces, they must be sintered or nodulized. The only specification as to the size of the sintered or nodulized product is that it must pass a 6-inch screen and not contain over 1t-1/2 percent minus 20-mesh material. The minimum-maximum size has not been established. Undoubtedly this opti mum size will be set by the ferromanganese industry when ample quantities of manganese oxide sinters have been smelted."

Mar 1, 1942

By M. A. Giralico

A new generation of hydraulic efficient pumper and auxiliary impeller designs is the result of an extensive research program focused on improving the overall performance of optimized SX/EW plants. Combined with the proper scale-up, these optimized designs will greatly reduce aqueous and organic entrainment losses, reduce or eliminate air entrainment and crud formation, enhance mass-transfer and maximize the overall copper yield. Currently, these new pumper and auxiliary impellers are installed full-scale in numerous plants ranging in flow rates from 90 to 15000 G.P.M. and developed heads up to 51 inches. Operational results reported by the independent metallurgist at each processing plant are reporting the lowest entrainment results in the industry. Further R&D has just been completed on a new mixing configuration that separates the systems mixing and pumping requirements. Results from the system pilot test document further improvements in reduction of both chemical entrainment and crud formation, while keeping mass transfer stage efficiencies.

Jan 1, 1998

By S J. Schafrik, C Keles, C Schlosser, E S. Gilliland, A K. Louk, N S. Ripepi, S Keim, J Amante, E Diminick

Three legacy coalbed methane production wells have been converted to injection wells for a one-year carbon dioxide (CO2) injection test to evaluate the potential for CO2 storage in the coal reservoir and the potential for enhanced gas production at offset wells. The injection reservoir is composed of 15–20 individual coal seams with an average thickness of 30 cm (1.0 ft), spanning a depth range of approximately 240 (800 ft) to 670 m (2200 ft).The monitoring program for this test includes gas and water sampling of the three injection wells, three dedicated monitoring wells and approximately 20 offset production wells. Key technologies used for monitoring the study area include time-lapse GPS and interferometric synthetic aperture radar (InSAR) acquisitions for surface deformation measurement, a 28-station buried passive microseismic monitoring array, real-time downhole pressure and temperature sensing and perfluorocarbon tracer fluids, which will be injected with the CO2 stream. The schedule for the monitoring program includes pre- (baseline), during- and post-injection data collection. This schedule will allow data to be analysed for time-lapse changes and trends, which are important for understanding the migration of gas and fluid phases in the reservoir – including CO2, methane, other hydrocarbons and water – and for observing the changing distributions of reservoir pressures and stresses.The results of the monitoring efforts for this study have implications for monitoring mining operations. The combined use of GPS and InSAR geospatial data to evaluate elevation changes across and beyond the study area may prove to be an accurate option for measuring surface deformation, including mining-induced subsidence, in unstable terrain. Long-term microseismic monitoring using high-sensitivity instruments has several applications in mining operations, including rock stability monitoring, production monitoring and miner location detection during emergencies. Tracer studies and short-term microseismic monitoring used to assess methane extraction can also be used to develop and optimise degasification systems for underground coalmines.CITATION:Gilliland, E S, Ripepi, N S, Schafrik, S J, Schlosser, C, Amante, J, Louk, A K, Diminick, E, Keim, S, Keles, C and Karmis, M, 2015. Monitoring design and data management for a multiwell CO2 storage/enhanced coalbed methane test in a stacked coal reservoir, Buchanan County, Virginia, USA, in Proceedings Third International Future Mining Conference, pp 47–56 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By M Graham, R Brunning, C Andringa-Bate, S Westergren

In 2010, Rio Tinto Iron Ore’s operations commenced the planning and design of a sampling and analysis system for the new 50 Mt/a Cape Lambert Port B (CLB) facility. Current sampling systems at the ports consist of automated robotic, mass-based sampling protocols employed at Dampier, and semi-automated, time-based sampling systems operating at Cape Lambert Port A.The new sampling system at CLB has brought together a fully automated sampling and analysis system utilising time-based sampling, with the capacity to sample ore products of medium quality variation as defined in ISO 3082 (ISO, 2009). The CLB system is required to sample at shiploading rates from 6000 t/h to 13 440 t/h and provide full load-port analysis. The sampling approach is to proportionally extend primary increments (of varying mass relative to shiploading rate) to a standard length using variable speed aero-belt conveyor systems. This enables a fixed number of secondary cuts to be achieved for all primary increment masses and to be delivered to the automated cell. The cell is required to be capable of concurrently processing four individual shipments, each containing multiple cargoes.Achieving the target sampling precision for all export cargo sizes has culminated in the planning, design and construction of the largest automated iron ore port laboratory in the world. The CLB sampling and analysis cell was commissioned in Q3 and Q4 2013. This paper discusses the sampling philosophy and commissioning outcomes.CITATION:Brunning, R, Andringa-Bate, C, Graham, M and Westergren, S, 2014. Cape Lambert Port B shiploading, sampling and analysis, in Proceedings Sampling 2014 , pp 79–90 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

The object of this program was to extend the capabilities of visual paging systems both in size and function. The system developed uses the mine pager phone line for communication, monitoring, and remote control. A central station, using a minicomputer, transmits signals by phase inversion modulation of a 16,384 Hz carrier to as many as 999 remote units. The remote unit addressed returns An echo to indicate that it is functioning and, in the case of monitor units, to convey the monitor data. Magnetically latched display dis[c]s, which can be seen from both sides when posted, are used for visual paging. Lists of the addresses of posted pages, unanswered pages, and non-echoing units are prepared by the central station computer. The system was designed to be intrinsically safe and should operate for three months on a 12-volt lantern battery.

Jan 1, 1980

I once read an æarticleÆ in FHM Magazine entitled æThe Coolest Jobs There Ever WasÆ. It was about a group of guys who were pursuing careers that any person on the planet would just kill for. I distinctly remember drooling over the pages, thinking how much I would love to be Michael SchumacherÆs Chief Engineer at Ferrari, or the Principal Designer and Tester for one of the big Dutch rollercoaster companies. From that moment on, I decided that I wanted a career that was cool enough to make it into the pages of that article. Throughout my time at university, I always had that article in the back of my mind. As a result I constantly wondered about what sort of job I could end up with once I left university. More importantly, I wondered if FHM would be banging down my door to put me in the magazine! After a long and stressful job hunting process (in between completing a thesis and studying for exams) I finally managed to land myself a job with Orica Mining Services. I can honestly say I didnÆt know what to expect when I first joined Orica. Most of my friends ended up working for big mining companies, while I was offered a position with one of the biggest suppliers to these mining companies. However, I had a feeling when I was discussing the role with my future supervisor during the interview process that the job was going to be awesome. I have now spent a year working for Orica and I absolutely love it! While I feel that my job is worthy of being in that FHM article, unfortunately, I donÆt think I am going to get my opportunity to be in the magazine. Apparently I donÆt look too good in a bikini! However, I would love to have the opportunity to discuss the journey that I have taken so far û from my time as an environmental science graduate, then moving on to mining engineering, to now, being part of the Orica Mining Services Graduate Program. My suggestion is to use this paper as a resource. I have learnt during my time at university, as well as my time in the workforce, that the best people you can learn from are your peers. Take what you feel is relevant from the paper; hopefully it will help guide you in shaping your own career.

Jan 1, 2005

By G M. Jones, J Rademan

Debswana, owned by the Government of the Republic of Botswana (GRB) and De Beers in a 50:50 joint venture partnership, operates the Jwaneng diamond mine in Botswana - the most valuable diamond mine in the world. The mine provides between 60 - 70 per cent of DebswanaÆs earnings, and about 30 - 40 per cent of the GRBÆs income. In 2008, the company embarked on the Cut 8 Project - an open pit waste cut-back to expose more diamond bearing ore to sustain mine life by another six to seven years. This undertaking was much larger than previous cut-backs; it increased the waste stripping ratio threefold, increasing significantly the waste handling fleet of trucks, shovels and infrastructure, and impacted a large part of the materials handling plant which required replacement with new facilities. The project coincided with the beginning of the Global Financial Crisis (GFC) and a slowdown in the economy. Its $4 billion total life cost was billed as æthe largest private investment project in BotswanaÆ which produced heightened expectations amongst stakeholders that it would redress some of the issues brought about by the GFC and leave behind a legacy of jobs, increased opportunities for citizen owned business and improved social infrastructure.Most of the big project challenges were non-technical and ranged from dealing with various stakeholders?at?all levels, a 25 per cent currency depreciation of the Botswana Pula against the South African Rand, obtaining work permits for non-citizens in a job starved environment, managing construction to world class safety standards, managing the low productivity of construction workers and producing a viable legacy program that satisfied the GRB and stakeholders. Whilst most of these risks were identified in front end studies, the magnitudes were in many instances underestimated. Managing this uncertainty on Cut 8 can provide valuable lessons to other projects in a similar environment, or at least provide the information to indicate that these factors should be adequately provided for in the financial evaluation of a project in the form of budget, schedule, contingency or risk mitigation.CITATION:Jones, G M and J Rademan, 2012. Reliability of expert judgements and uncertainty assessments, in Proceedings Project Evaluation 2012 , pp 109-116 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By Victor R. Eyzaguirre

Cerro Verde is one of several large porphyry-type copper deposits in Southern Peru. The copper occurs as primary sulphides, with a significant oxide capping. The exploitation of the deposit has been correspondingly divided into two stages, the first consisting of copper production from oxides, and the second from sulphides. Minero Peru successfully started the Stage I plant in June of 1977 with the first production of electrowon copper cathodes. This paper is essentially devoted to a description of the Stage I process, which can be summarized as follows: Ore is trucked to the primary crusher, where it is crushed to 225 mm and conveyed to a coarse ore stockpile. Ore withdrawn from the stockpile is secondary crushed to 65 mm, conveyed to a truck loadout bin, loaded into trucks and driven to the leaching pads. Ore is placed on the pads in lifts and sprayed with sulphuric acid solution to dissolve the copper. Copper-bearing solution forms a pond behind a dam at the lower end of each pad and is pumped from there to the solvent extraction plant. Copper is extracted from the leach solution into an organic phase and is then stripped from the organic phase to form a purified concentrated copper solution suitable for feed to electrowinning. In electrowinning, the copper is finally recovered as cathodes suitable for sale as refined copper.

Jan 1, 1978

By P A. Grossman, J H. Rubinstein, M Brazil, D Whittle

Many ore reserves are harvested by a combination of open pit and underground mining methods. In these cases, there is often material that could be mined by either method, and a choice has to be made. The area containing this material is referred to as the transition zone. Deciding where to finish the open pit and start the underground mine is referred to as the transition problem and it has received some attention in the literature since the 1980s.In this paper, we provide a review of existing approaches to the transition problem encompassing: graph theory-based optimisation employing an opportunity cost approach, heuristics and integer programming. We also present a novel opportunity cost approach, that takes into account a crown pillar, and show how the new approach can be best applied through the unconventional application of an existing mine optimisation tool.CITATION:Whittle, D, Brazil, M, Grossman, P A, Rubinstein, J H and Thomas, D A, 2016. Determining the open pit to underground transition – a new method, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 731–742 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By H. M. Garrett

Dr. Ft: L. Handy of Iowa State University's Engineering Experiment Station very handily reduced the relatively complex cement making process to ultimate simplicity: "Take two cups of crushed limestone; add one-half cup of clay or pulverized shale (plus perhaps some sandstone or iron ore; depending); mix thoroughly and grind up fine. Bake in white-hot oven at about 2,600 F. Cool. Add a tablespoon of gypsum: and, again, grind very fine. If you can do this for about a penny a pound, you can almost compete.' Before Dr. Handy's time, is the early days of the U. S. Cement Industry, from 1817 when the Erie Canal was started to 1895 when the first rotary kiln was built, this was the recipe, more or less. Dr. Handy's raw materials were deposited in a natural "cement rock" found in the Hudson, New York and Lehigh, Pennsylvania valleys. At first the natural rock was pulverized (not ground fine) and interlayed with wood for "baking" at about 1,800° F in a batch process vertical shaft kiln or beehive oven; then the calcined pozzalonic (lime and silica) product was cooled and ground fine for shipment in wooden barrels. Later, in 1871, true portland cement was made. The same natural rock was ground fine to make briquettes; interlaced with wood or coal in the "Beehives"; and baked at a clinkering temperature of about 2,6000 F to produce clinker (calcium silicates) which was ground fine for sale. In those days, the crude cements dropped in price from over 1 cent to 1/2 cent per pound. In 1895 the rotary kiln introduced-continuous instead of batch processing. The countercurrent process allowed the same raw materials (now finely ground to about 80% minus 200 mesh like face powder) to be fed at one end of the rotary kiln. Heat from a coal burner was introduced with combustion air at the other end to produce the requisite clinkering temperature. The clinker product was discharged for atmospheric cooling, mixed with gypsum, and again ground fine as face powder. The cement was sold primarily in barrels, later in jute or cloth bags, then paper bags, and now primarily in bulk truck and barge carriers. The price dropped to a 1/4 cent per pound by 1910, but with recent inflation it now sells for 2 cents per pound.

Jan 1, 1978

By E Mielczarski

Determination of the adsorbed layer composition and structure at molecular and atomic levels and understanding adsorption mechanisms and dynamics are vitally important for the preparation of surface layers with specific functions. Direct information, at a molecular level, about mineral surface composition, its structure and surface distribution is crucial to perform an efficient separation process for mineral beneficiation. This information is equally important for modifying surface properties of industrial minerals for specific applications such as: fillers, composites, weathering resistance, etc. An understanding of the mechanisms and kinetics of the interaction of first adsorbed organic molecules with mineral surfaces is a fundamental requirement for the prediction and control of the macroscopic surface properties governing the efficiency of separation technologies or new material formulations. The developed infrared external reflection technique has a unique ability to study interface phenomena, at a molecular level, on heterogeneous substrates. The variety, precision and reliability of information about the interface phenomena delivered by this technique is superior to any other single technique. The experiments are fast and non-destructive. High sensitivity (starting from 20 per cent of the monolayer) in situ collected information in a multiphase system, even in the region of strong absorption of the substrate, makes this technique a very valuable experimental tool. The complexity of the recorded reflection spectra, their sensitivity to variations of the optical properties of all bulk and surface components and their spatial distribution in the system under investigation, are in fact the major strengths of this technique. A few examples of the application of this multi-diagnostic technique, for monitoring surface modifications of semi-soluble minerals for selective flotation, will be discussed in detail in this paper.

Jan 1, 2005

By W. J. Fullerton

This paper is one of a series being prepared by the U. S. Bureau of Mines describing mining and milling methods and costs at cement-plant quarries throughout the United States, end deals directly with methods and costs at the quarry and mill of the North American Cement Corporation at Catskill, N. Y. The process of manufacturing cement is described only as far as the final grinding of the raw materials. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs may in many instances cause embarrassment to individual producers, as well as to the industry as a Whole. On the other hand, operating costs are essential to the technical discussion and study of methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding; of the scone of the cost tabulations may ensue.

Jan 1, 1931

By G. Ferrara

The paper describes the new design criteria and control strategies for multi-density dense medium separation (DMS) circuits. The role of the multi-density separation is discussed, and it is emphasized that for many processing problems -related to minerals and coals -it may be very important to perform two or more cuts at different densities in order to obtain a remarkable improvement in quality of products, process efficiency and economy. The two-density separation by dense medium cyclones was generally performed using two dense medium plants in sequence. In contrast to the former technology, the multi-density separation can now be performed by using a single medium circuit composed of different interconnected medium sumps. The sumps, one for each density, are fed with different medium streams selected according to their density, size composition and content in non-magnetic contaminant in such a way that the rheological properties of the media are optimized. This new technology is based on dynamic systems to density the medium, on the size-density segregation of the medium in the cyclones and separating devices and on accurate control systems for the density, viscosity and stability of the dense media of the different sumps. The present paper reports on the theoretical basis for the new, advanced medium circuits and on the systems for the control of the densities and of the rheological properties of the dense media. A typical circuit for a two-density separation is also described, and some industrial applications reported and discussed.

Jan 1, 1994

By Rohan Fernando, David P. Snyder, John F. Burr, Susan M. Moore

"The Mine Improvement and New Emergency Response Act of 2006 (MINER Act Public Law 109-236) was passed by Congress in response to three major underground coal mine accidents in the United States that claimed the lives of 19 miners. The Act resulted in substantial changes in the underground coal industry relative to the use of technology for mine escape, rescue, disaster response and other areas where the lack of these technologies contributed to the fatalities caused by these tragedies. This year marks the 10th anniversary of the MINER Act, which makes it an opportune time to reflect on the events that led to its passage, the changes that have been made since then, and the work that remains to be done.As discussed below, the last decade has demonstrated tremendous cooperative efforts among mining operators, technology innovators, labor, The National Institute for Occupational Safety and Health (NIOSH), the U.S. Mine Safety and Health Administration (MSHA) and state regulators, resulting in substantial improvement of the technologies used for escape and rescue and noteworthy progress toward meeting many of the goals of the MINER Act. While the MINER Act and this article pertain primarily to coal mining, many of the technologies are equally applicable to any underground mining and have already found some acceptance outside of coal.Technology gaps targeted by the MINER ActThe MINER Act addressed several technology challenges:• Problems with donning and switching between self-contained, self-rescuers (SCSRs).• Poor visibility in smoke.• No wayfinding assistance for escape from the mine.• Limited breathable air supply.• Inability to locate trapped miners.• Inability to communicate with trapped miners.• Failure of mine seals."

Dec 1, 2016

Problems caused by water discharge from surface mine ventilation shafts can be significant and are usually unforseen. The discharged water is often hyper-saline or acidic and can cause environmental degradation over a wide radius. It can also lead to recurring power pole fires and primary fan breakdowns. A range of solutions to the water discharge problem has been implemented in many Australian mines. In most cases the solutions have been ad hoc, with the overall cost and effectiveness varying tremendously. This paper reviews and contrasts the practicality and effectiveness of the various available remedial options.

Jan 1, 2002

By M. A. Evanto

Since the late 1970's, the Roof Control Division (RCD) of MSHA's Technical Support has been performing linear analyses for the enhancement of miners' safety. This remote sensing process uses Landsat data to predict areas of potentially hazardous ground conditions in underground mines. To date approximately 700 analyses have been completed by the RCD, with nearly 75 being performed with the current equipment, software and methodology which was updated in early 1995. While success is difficult to measure, requests for linear analyses continue to come from large and small mining companies which suggests the industry's acceptance of the process.

Jan 1, 1998

By Long Han, Jianyuan Liu, Ping Ying

"Particle-bed compressive stressing is the main work mechanism of comminution by high pressure grinding rolls(HPGR). An experimental study on comminution and mineral liberation of two copper sulfide ores was carried out using a piston-die compressive stressing rig to simulate the situation of comminution with HPGR as the final-grinding device. The tests carried out include compressive comminution tests on particle-bed with narrow-size feed, and the locked-cycle comminution test on particle-bed with broad-size feed, which was then compared to a corresponding locked-cycle test of ball-mill grinding. The narrow-size feed is made up of particles in the size range 2.36~3.35 mm, whereas the broad-size feed of particles in the size range 0~3.35 mm. The liberation analysis for copper-mineral in the comminution products was accomplished using BPMA system – an automatic mineral liberation analyzer developed by BGRIMM. The influences of the stressing intensity and the method of comminution on the copper mineral liberation are discussed in terms of product size distribution, copper-metal deportation among size fractions, distribution of copper mineral among particle-size and particle-grade classes, degree of mineral liberation in size class as well as degree of mineral liberation overall.INTRODUCTION Traditionally, comminution process commonly applied in mineral processing is a flowsheet consisting of crushing of crude ore with conventional crushers, followed by grinding of the crushed ore in tumbling mills. In last decades, the energy-efficient HPGR (high-pressure grinding rolls) has found its application in mineral processing, mostly as tertiary or quaternary crusher to generate a fine-crushed product either as feed to subsequent grinding or as feed to a pre-beneficiation process before further grinding. Compared with the process of conventional crushing followed by grinding in ball mill, this mode of HPGR-application can achieve energy saving to some extent by reducing particle size of the feed to ball milling, and by reducing amount of the feed to ball milling if a significant portion of tailings in relatively coarse particle-size range can be discarded at the pre-beneficiation stage. In recent years, the approaches of letting HPGR take more comminution work from ball mill by applying it in semi-finish grinding mode or even finish grinding mode have been discussed (Burchardt, 2014). Although HPGR finish-grinding has been successfully applied in the cement industry for grinding of cement clinker and raw materials, this mode of HPGR application has yet rarely been implemented in mineral processing, despite the advantage of more energy-saving and other potential benefits such as preferential breakage, internal damage of particles and enhanced mineral liberation which may lead to a better downstream processing performance. The reasons for the retardation of the progress of this kind of HPGR-application in the mineral industry lies not only in that a finish-grinding with HPGR has to be operated in dry condition whereas most of ore-beneficiation processes like flotation are operated in wet condition, but also in that there are large variety of ore materials with various complexity of processing technology, which need to be addressed on a case-by-case basis with a lot of test work, in order to evaluate the potential advantages or disadvantages of this application."

Jan 1, 2018

By A Vakili, F Harvey, H Greaves

Mine seismicity is one of the most difficult geotechnical risks to manage in seismically active mines. There are currently some established empirical and statistical methods that provide quantitative measures for seismic hazard assessment in operating mines. However, these methods are mostly suitable for quantifying the current or historical seismic hazard and often cannot be directly used to forecast the future hazards. Numerical modelling is the only analytical tool that can capture the level of complexities required for a meaningful analysis of mine seismicity and therefore to facilitate a reliable forecast of future hazards. However, there is currently no widely accepted and established guideline and methodology for analysing and forecasting mine seismicity using numerical modelling. This paper first provides a background on previous published studies on this subject and then outlines the key aspects that can affect the reliability of the forecasting for mine seismicity. These aspects include a) processing of historical seismic data, b) selection of suitable numerical modelling approach, c) Post-processing and interpretation of the model outputs. A case study is then presented for the Gwalia Deeps Mine where a new framework was developed to forecast future mine seismicity. High-quality seismic data for a period of five years was used for back-analysis and comparisons with the numerical modelling outputs. After development of the method, the future seismicity was forecast for the next 12 months and the actual seismicity was monitored against the forecast during this period. Results of this study shows promising potential for the proposed framework to be applied more routinely and at other mine sites. However, more validations are required at Gwalia Deeps mine as the mine proceeds to deeper levels. In addition, the method needs more improvements and should be tested and validated at other mining operations before it can be established as a proven method. CITATION:Vakili, A, Harvey, F and Greaves, H, 2018. Forecasting mine seismicity – towards a more established methodology, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 207–222 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018