Search Documents

By J. G. Donaldson

Cobalt-tungsten binary deposits were formed in laboratory experiments by hydrogen reduction of the anhydrous mixed vapors of cobaltous chloride and tungsten hexachloride. The materials were sublimed in seperately heated zones of reaction tube and were transported in a stream of purified helium into the deposition section of the tube where the chloride gases were reduced to metal by a countercurrent flow of hydrogen. Heattreating of the near stoichiometric binary metallic deposits converted nearly all to the intermetallic compound Co3W, however, small quantities of both cobalt and tungsten remained. Mechanical tests showed that the tensile strength of heat-treated 75 percent cobalt-25 percent tungsten deposits was twice as high as that of similarly treated deposits of cobalt.

Jan 1, 1965

By S. H. Ash

The United States Bureau of Mines has published relatively little on the flooding and unwatering of coal and metal mines. Bulletin 229, Fifty-Nine Coal-Mine Fires, published in 1927, contains several instances of the flooding of mines or sections thereof to extinguish fires but does not describe their unwatering. Report of Investigations 2649, Explosion Hazards Incidental to Unwatering Coal Mines, published in 1924, warned against the possibility of gas accumulations in flooded mines and indicated the precautions to be taken. Report of Investigations 2255, An Unusual Hazard in Reopening Long-Flooded Timbered Metal Mines, published in 1921, told of methane being pocketed and the danger thereof. The flooding of mines originates in many ways. At some mines flooding followed reopening after what was thought to be permanent abandonment; also, explosions have caused some mines to be flooded. Extinguishing fires, accidental encountering of underground streams or flooded old workings, and caves of strata admitting water from underground workings, water-bearing strata, or surface accumulations have also flooded all or parts of mines. Unfortunately, un watering often necessitates much study and causes apprehension largely because experiences in similar situations are not generally known, as few descriptions of successful or unsuccessful methods are available. The job has sometimes been contracted for outside the local management involved and has become a matter of record for the contractor only. As the cost-plus contract system often employed in the past is now known to be expensive, careful managements elect to handle the problem themselves, in line with the general policy of cutting expense where possible. This report describes specific in-stances of successful unwatering by operators.

Jan 1, 1933

By Peter M. Power

A microscopic study was made of a series of simultaneous slag and metal samples taken from a low carbon basic open hearth heat. An attempt was made to identify the various micro-constituents found. As the various impurities in the bath are oxidized, the metal structure changes from that of high-phosphorus white cast iron to that of low.-carbon steel. A detailed study of phosphorus distribution is included. The acid run-off slag has an .acicular orthosilicate structure which changes on 'shape-up' to a very basic tri-calcium silicate and calciuim ferrite structure. Many unidentified minor constituents are present in the slags. Though metallography will never replace chemic.al analysis of the bath, the microsopic study of polished slags has some promise of being useful in slag control work.

Jan 1, 1956

By G. Chancellor

"INTRODUCTION The paste plant is located at the Barrick Goldstrike mine in Northern Nevada on the Carlin Trend. The Goldstrike property consists of an open pit and an underground mine; along with two processing facilities: a roaster and an autoclave. The underground portion of the mine produces approximately 1,800,000 ore tons per year and approximately 400,000 ounces. The mine is broken up into four distinct zones: Banshee, Meikle, Rodeo and Northpost. The current paste plant services both the Rodeo and Northpost zones. Development of the conceptual designs and permit approval for this plant was an extensive process that took over a decade to complete. A testing program was developed in conjunction with this process and implemented throughout to ensure the following metrics were achieved: ensure no environmental impact, material available onsite would be able to flow through the pipe to all required locations, and that this material could achieve the appropriate final strength. PLANT AND UNDERGROUND CONSTRUCTION This is the first paste plant to be built in Nevada. The paste plant at Goldstrike began construction in January 2012 and was completed in March of 2013. This plant was constructed to service the Rodeo side of the underground mine which previously utilized a cemented rock fill (CFR) plant to meet their backfill needs. However, in March of 2013, the same month the plant was commissioned, the raise that fed this CRF plant was mined out in a planned phase of the adjacent open pit. This made the switch to paste all the more difficult as it was being relied on for as the sole source of backfill production even though the system yet to be fully tested and optimized. The plant was designed to be fed with onsite Roaster tailing which would be thickened and then mixed with cement and fly ash. The plant was designed to pump 177 tons of paste per hour with a utilization of 65%. The original design specifications for the paste were 77% solids with varying binder contents depending on where the paste was being placed"

Jan 1, 2015

A processing scheme is presented to use one single chemical that has multiple functions to re-duce the use of chemicals and achieve more efficient mineral flotation and solids dewatering. Sti mulisensitive polymers which display hydrophilic/hydrophobic transitions in response to changes in temperature or pH have been found to be useful as such multiple function reagents. They can cause the mineral particles to be either hydrophilic or hydrophobic at one stimuli condition and the opposite at the reverse stimuli condition. Therefore, both particle surface wettability and inter-particle interaction forces are reversibly controllable. When the surface is hydrophilic, particle dispersion is achieved by repulsive inter-particle forces whereas when the surface is hydrophobic, particle aggregation is induced by inter-particle hydrophobic attractive forces. In addition, the hydrophobic surface condition allows for the attachment of particles to bubbles. Flotation and solid settling tests have been conducted with a silica suspension treated with the temperature-sensitive polymer poly (N-isopropyl acrylamide) (PNIPAM). The results indicated that PNIPAM can be used to induce a transition between hydrophilic and hydrophobic surface character at temperature lower or higher than its critical solution temperature (CST around 32oC). Thus, both effective silica dispersion or hydrophobic aggregation and flotation without adding any additional collector have been demonstrated. In tailings treatment, rapid silica settling was obtained with hydrophobic aggregation at temperature above the CST and further sediment consolidation (and water release) occurred at temperature below the CST. Contact angle measurements confirmed the hydrophilic/hydrophobic transition induced by PNIPAM.

Jan 1, 2014

By J. M. Rios

This paper exposes the reasons that led the Empresa Nacional Minera del Sahara, S.A. (ENMINSA) to the selection of a conveyor belt system for the transport of phosphate rock over a distance of 100 kilometers. ENMINSA was created in 1962, with the main objetive of the exploitation of phosphate rock deposits in the Spanish province of Sahara, in North West Africa. Poor grade outcrops were known previously. A detailed geological research carried over the province led ENMINSA to the discovery of deposits not exposed, and of much higher grade. The sector known as Bu-Craa was chosen as the most promising, and was explored by means of drill holing and shafting. The important amount of information obtained permitted a detailed evaluation of the capacity and grade of the rich ore contained in the Bu-Craa area. Simultaneously with the systematic reconnaissance of the Bu-Craa deposits, ENMINSA developped the study of the technical and economical problems required for the beneficiation of the rock, which comprised five main groups of projects: rock exploitation; beneficiation plant; rock transport from the mine site to the Atlantic coast; storage, handling and loading facilities by the sea- side, and power plant. Once determined the location of the marine loading facilities, which to date are in an advanced stage of construction (figs. 1 and 2), the studies conductive to the selection of the best transport system from the mine to the ocean, along 100 kms. distance were undertaken.

Jan 1, 1968

By N Johansson, D Johansson, A Beyglou, H Schunnesson

As demand for optimisation of mining processes increases, more attention is drawn to blast performance and fragmentation improvement. Fractures and discontinuities are among the most influential factors in blast results, therefore one of the initial steps towards blast optimisation is to gather information about the rock mass and integrate it in blast design. This paper presents a method for assessment of rock mass discontinuities and integrating it in production blasts in the Aitik open pit copper mine in Sweden.3D photogrammetric techniques were utilised to map discontinuities and distinguish domains of similar geologic structures in the pit. As a pilot study for a future campaign, four different initiation directions were tested through six pilot blasts in one of the domains. The results were compared in terms of swell and loading efficiency of rope shovels to identify the correlation between blast performance and initiation direction compared to major discontinuity families.It was established that in the trial domain, blasts initiated towards north or north-west yielded larger swell and better performance of loading. Comparing these blasts with discontinuity families show that there is a correlation between blast performance and initiation direction according to the dip and strike of these discontinuities. Such knowledge can be used for future blasts in the same domain to increase long-term operational efficiency through slight modifications in drill pattern and initiation design.CITATION:Beyglou, A, Schunnesson, H, Johansson, D and Johansson, N, 2015. Adjusting initiation direction to domains of rock mass discontinuities in Aitik open pit mine, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 385–392 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Charles Bruce

Although much has been said about the high cost of exploration, both at home and overseas, little of a specific nature has been published on actual finding costs, if indeed such data has been developed. This contrasts sharply with our sister industry, petroleum, where finding costs for oil and gas are available for virtually any country In the world. The reason is largely attributable to the genetic complexity of the hard minerals, as opposed to petroleum, and the increasing difficulties we are facing in the search for new orebodies. We have available to us data on the annual exploration budgets of most of the major mining companies which show them to run into the tens of millions of dollars. My co-panelist, Dr. Walthier, Director - Corporation Exploration, St. Joe Minerals Corporation, New York, NY, summed up the feelings of many explorationists in a recent keynote address when he stated, "I would not recommend a mineral exploration program of a general nature in North America budgeted at less than three to four million dollars annually, spread over four to five years -- or smaller amounts for more years". We have the fact that many of the major companies now prefer to "buy into" a new mineral discovery, particularly overseas, because of the high-risk and high-cost of exploration. Is there, then, a place for the small investor, let us say with a budget of under $200,000 per year and, if so, where and how? This paper is directed toward the above question and is based on experience gained while managing a limited international exploration program, on a shoestring, over the past three years.

Jan 1, 1976

By Alfred E. Pugsley

PAYMASTER CONSOLIDATED MINES, LIMITED, began an investigation into the economy and use of detachable bit drill-steel in June, 1937. This investigation has continued to the present time, and was made necessary by transportation and distribution difficulties that had arisen through the use of standard steel in three widely separated mine areas serviced by a central steel-sharpening shop. Detachable bit drill-steel performance was first studied in the workings of No. 2 mine, where the rock being drilled was composed mainly of porphyry or tourmaline, and where standard drill-steel transportation costs had been excessive. The results obtained in this early work definitely established the economy of detachable bit drill-steel at No. 2 mine. This conclusion was reached when the 're-grind' system of re-sharpening dulled detachable bits was 1n use. Preliminary observations on the performance of detachable bit drill-steel in the quartz-carbonate veins of No. S and No. 6 mines gave encouraging results, and warranted a large-scale investigation under practical mining conditions. All drilling operations were gradually changed over to use of detachable bit drill-steel. This change was completed by February, 1938.

Jan 1, 1939

By Douglas K. Modrow

In the fall of 1993, construction was completed on a state of the art industrial waste water treatment plant at Asarco's East Helena Lead Smelter. Purpose of the plant was to remove arsenic and metals using hydroxide precipitation. Completing of the plant culminated a lengthy process of laboratory bench-scale test work, engineering, construction, and Environmental Protection Agency (EPA) oversight. Unfortunately, the effiuent requirements for the plant were made significantly more stringent as construction was rearing completion. As a result, optimization activities were initiated to determine and implement measures to substantially improve effiuent quality so the new discharge limits could be met. These activities consisted of acquiring a thorough understanding of process chemistry and plant operations, and developing simple, practical methods of automating unit operations associated with the treatment plant. Implementation of these modifications in the second half of 1996 will not only significantly improve the constancy and reliability of treatment plant operations, but also result in operating cost savings and reduced need for increased operator attention at capacity flows, plus allow the treatment plant to meet the new discharge limits.

Jan 1, 1996

By Katja Ohenoja

Polymer dispersants, also known as grinding aids, are widely used to reduce the viscosity of mineral particle suspensions and to improve energy efficiency during fine grinding. In this study, the effect of polymer dispersant with different molecular structure on the suspension properties in the wet stirred media milling of limestone was studied. The stability of suspension was studied by combining rheological and zeta potential measurements. The PDI value of polymers corresponds to the width of the molecular weight distribution so that low PDI corresponds to narrow MW distribution and high PDI to the wide one. In this study, two traditionally fractionated polymer dispersants with high PDI (over 2) and one novel polymer dispersant with low PDI (1.2) has been tested. It was noticed that dispersants worked as electrosteric stabilizators and prevented the agglomeration of ground limestone particles. The uses of dispersants could increase solids concentration used in the grinding experiments and at the same time lower the particle size and specific energy consumption. The obtained particle sizes were about 1 µm regardless of which dispersant was used or the amount of it. The novel dispersant with low PDI reduced viscosity most when compared with the traditionally fractionated polymer dispersants. Results indicated that even higher solids concentrations can be used at the same amount of dispersant when the novel low PDI polymer dispersant is used. Alternatively, lower dosage of novel low PDI dispersant can be used compared to traditionally fractionated dispersants.

Sep 1, 2012

By Gerald V. Gibbs

As a part of the Bureau of Mines long-range program in asbestos, synthetic asbestiform compounds and minerals were prepared and described. Fundamental structural data on two such compounds are given in this report. Crystallographic data are provided for the synthetic isotypic compounds potassium-lead silicate, K2.Pb4 -Si8021 (I), and lead-aluminum silicate, Pb2. Pb4 .Al2Si6O21 (II). The space group symmetry 14/mmm was assigned provisionally to I and II on evidence of single crystal and piezoelectric measurements. A statistical evalua¬tion of indexed powder diffraction data revealed the cell edtes of I to be a 11.816 and c 7.932A and those of II to be a 11.723 and c 8.044A. The phases are uniaxial with observed refractive indices eD 1.790, an ?D,699 and eD 1.884, cusp 1,807, respectively. The atomic structure of I and II may be based on a complex of chains of silicon-oxygen tetrahedra lying along the c cell edge similar to the type of chain structure postulated by Pauling for scapolite. K2.Pb4.Si8021 and Pb2.Pb4 Al2Si6021 were first described by Geller and Bunting (5, 6)4 as fibrous compounds similar in crystal habit to asbestos. These authors gave powder diffraction data, although no attempt was made to find the cell edges or to index the powder diffraction patterns. Later, Shell and others (9) conducted a crystallochemical study of these fibrous silicates in search of a substitute for strategic asbestos. Their single crystal data revealed K2.Pb4 -Si8021 to be tetragonal body-centered with cell edges a 11.66, c 7.95 A. Pb2.Pb4 Al2Si6021 was concluded to be isotypic with K2.Pb4 -Si8021 on the basis of similar powder diffraction patterns, chemistry, and physical properties. No attempt was made, however, to index the powder diffraction record nor to determine the appropriate space group of either compound.

Jan 1, 1962

By Z. Zhang, M. S. Gonzalez, M. de P. Bueno, P. Holopainen, S. Luukkanen

In an extremely competitive mining industry, onsite experience is a big advantage. Mining education at the universities is mostly focused on theoretical studies without a possibility of practical training in mining sites. Hence, experimental mines suitable for practical education are needed to provide a platform for systematic research and education in industrial scale and for training in real mining conditions. Yet, this kind of mine sites is rare worldwide. Thus, a new educational research project, namely MINETRAIN is introduced in this paper evaluating the transition of the Pyhäsalmi mine in Central Finland from an active base metal mine to a research, educational and training underground facility. The uniqueness of MINETRAIN compared to other test mine programs is that the existing state‐of‐art infrastructure in Pyhäsalmi enables research and training facilities among all disciplines related to the overall mine value chain. Though all the above sound interesting in the context of research and education purposes, in practice Pyhäsalmi will have to become an experimental mine that can be sustainable in the future. Accordingly, a prefeasibility study is being conducted and some preliminary results are presented in this paper. INTRODUCTION Despite being a field of studies that requires practical knowledge and experience, mining engineering education follows the same pattern in most mining universities around the world; consisting of theoretical courses and laboratory-based practical modules (Mischo, 2015). The possibility of having practical training in real mining conditions on actual mine sites or processing plants is limited to none, while the only contact that undergraduate students have with mining operations during their time of studies is usually through short-time internships or visits in the context of educational trips. Yet, real integration between universities and the mining industry may be scarce, which does not help students to observe the actual processes, and thus understand the whole picture of mining operations. Indirect practical training is also possible nowadays that technology is shifting from mechanical to digital, and the use of virtual reality -in the context of Mining 4.0- can provide additional experience to the learning process. However, virtual reality is limited to the visual impression and is also limited in actions (Binder et al, 2018). In any case, when there is not a proper pragmatic view of how the different disciplines link to each other and especially if there is a lack of communication, unfortunately the results could be seen at a later stage in the mines as a poor performance of professionals and workers. Another major challenge for educating specialists in the mining sector is that experimental mines suitable for practical education, where the skills and know-how could be developed and/or enhanced are rare worldwide. Such research and educational (R&E) facilities are practically former metal ore mines that have been transformed into experimental sites. Besides being limited in number, not all facilities of this kind serve both a research and educational purpose.

Jan 1, 2019

By Karl Peterson, Bibhu Mohanty, Chanakya Nariseti

The mechanism of crack formation in two target rocks (Kuru granite and Flamboro Limestone) is studied experimentally by simulating the impact action of a percussive drilling bit. Rock samples are dynamically loaded using a custom made impacting bit (8 mm, 12 mm and 15 mm diameter bits). The target rocks are impacted at velocities 8, 10, and 12 m/s. The resulting crack patterns are visualized by three techniques, Dye penetration, CAT scans and Optical scans. Mapping of the crack patterns is manually done with Photoshop. For 3D damage visualization, the crack patterns are mapped in two planes (impact surface and longitudinal sections). The three techniques are compared to determine an optimum technique for better damage visualization. The evolution of crack pattern with impact velocity and bit diameter is discussed.

Jan 1, 2015

By B. T. Field

Pyroprocessing systems range from low temperature dryers to high temperature reactors. The materials and process requirements cover a broad spectrum. It is not the intent of this paper to do a detailed examination of individual processes and equipment, since that can be found in a multitude of other sources; rather it is the intent of this paper to examine the key process variables and offer empirical guidelines to assist in a user?s overall evaluation.

Jan 1, 1998

By M. P. Hoffman

The U.S. Bureau of Mines is developing a roof bolter with a computer-controlled drill head that will increase the safety of roof bolting in underground coal mines by allowing miners to be relocated to a safe area. To ensure secure anchorage, acceleration and strain data are broadcast from an instrumented drill steel to a data acquisition system. These data are analyzed, correlated, and transformed to pro-vide information about roof strata, then are sent to a supervisory computer executing National Institute of Standards and Technology's real-time control software. The supervisory computer sends setpoint commands to proportional-integral-derivative control loops to control drill thrust, position, revolutions per minute, and torque.

Jan 1, 1994

By D. C. Martin

Construction of the Cerro Colorado on-off leach pad in northern Chile required placement of approximately 3,000,000m3 of fill over a P1an area of approximately 600,000m in irregular terrain with relief of up to 40m. Earthwork construction was completed in approximately six months using mine waste which was placed in 4 to 6m lifts using mine haul trucks. The lift thickness was reduced and the compactive effort increased in the upper 10m to enable development of a mat and additional resistance to possible differential settlements under dynamic (earthquake) conditions. A single 80 mil (2mm) HOPE liner was used below the leach pads and this was protected from the loading and unloading equipment using an engineered liner system consisting of screened sand, gravel and silt from local sources as the bedding and cover layers, and a heel of screened gravel and primary crushed low grade ore. Settlement monitoring, field testing and subsequent assessments of liner performance have indicated an adequate design was achieved and the project proceeded with considerable savings in time and construction costs.

Jan 1, 1995

By M. R. Lastra

Island Copper Mine began gold recovery Tom molybdenum sulfide concentrates in April, 1985. Plant design capacity is 20 tons of molybdenum concentrate per day. The molybdenum concentrate is produced in a conventional copper/molybdenum flotation circuit by selective copper depression. After thickening, the molybdenum concentrate is leached with cyanide solution in a series of five leaching tanks. The leached concentrate is then filtered and soluble gold values recovered on activated carbon with a six column adsorption circuit. The gold leach extraction is approximately 80 percent with a gold adsorption on activated carbon of 97 percent.

Jan 1, 1986

By C. Joulian, A. G. Guézennec, A. Chmielarz, Y. Ménard, M. Hanke, P. d’Hugues

"The copper concentrate used in this study is produced by flotation of a black shale organic rich ore. This resource is a carbonate-rich, polymineral concentrate. In the last 5-6 years, ore characteristics changed and the concentrate grades degraded. This study evaluated bioleaching of the concentrate in stirred tank reactors as an alternative to the pyrometallurgical technology that is currently applied, and which may no longer be feasible in future given the concentrate chemistry.The first part of the study focused on testing non-traditional operating conditions during continuous bioleaching experiments: high solids concentration (> 20% solids), reduced agitation and aeration rates. For the same residence time, bioleaching performance at high solids loading (25%) was the same as that reached during previous bioleaching experiments at 15% solids. No mixing or microbial issues were encountered. The bacterial consortium used in the experiments demonstrated a high copper tolerance.The second part of the study was devoted to technology development for metal recovery from copper bearing solutions obtained during bioleaching experiments. Due to the high copper concentration of the leachate, solvent extraction prior to electrowinning was not necessary. After iron removal, high quality copper cathodes (morphology and composition) were obtained from the PLS by electrowinning."

Jan 1, 2014

"The pressure leaching of alkali-pretreated limonitic laterite ore in nitric acid was studied. The optimal leaching conditions are as follows: leaching temperature of 458 K, initial nitric acid of 2.44 mol/L, leaching time of 60 min, liquid to solid ratio of 2:1 mL/g, agitation speed of 500 RPM. Under the above conditions, the extraction of nickel and cobalt can be achieved as approximate 95% and 80% respectively while that of iron is as lower as 1%. The leaching residue containing 70% of iron in the form of hematite and trace amount of chromium is suitable as the raw material for iron-making. The nitric acid in the leaching solution can be regenerated and further recycled to leach. INTRODUCTIONIt has been estimated that 60%-70% of the world land-based nickel resources presented in nickel laterites containing 130 million tons of nickel although these only accounted for about 42% of the world nickel production (Sudol, 2005; Luo et al., 2010). The nickel resource of laterite has not yet been fully utilized. Due to the increasing global demand of nickel and the declining global reserves of nickel sulphides, there is an increasing focus on the processing of the huge reserves of laterite ores today. Nickel laterite ores can be simply divided into two types, namely, silicate-rich and limonite. The former can be treated effectively by pyrometallurgical process in which the ferronickel product or nickel/iron sulphide matte is produced (Monhemius, 1987). The limonitic laterite is rich in iron in the form of goethite which is the main nickel-bearing mineral and usually contains cobalt associated with a manganese phase (Chang et al., 2010; Georgiou and Papangelakis, 2004). The limonitic laterite is usually processed by hydrometallurgical methods, such as atmosphere acid leaching (AL) (Xu et al., 2005; McDonald and Whittington, 2008), high pressure acid leaching (HPAL) (Chou et al., 1977; Georgiou and Papangelakis, 1998; Rubisov et al., 2000; Whittington and Muir, 2000) and reductive roasting-ammonia leaching (Caron Process) (Whittington and Muir, 2000; Valix and Cheung, 2002). The AL process can proceed at lower temperature, thus the operation costs may be very low. But two biggest problems associate with the AL process, namely, the slow rates of nickel extraction and potentially the significant amount of impurities such as iron and aluminum in the leaching solutions, which hampers the wide application of the AL process. The Caron Process uses the pyrometallurgical and hydrometallurgical methods together to obtain the metallic values, but the overall metal recovery is relatively low, especially for cobalt. In recent years, the environment-friendly process of HPAL has become increasingly important because it is most suitable for low-grade ores and leads to high extraction of the valuables. However, the HPAL process needs a much higher temperature and pressure (503-533 K, 4-5 MPa) to maintain a relatively fast leaching rates, which results in higher operation costs. Moreover, another serious problem of scale formation in autoclaves occurs in the HPAL process, for example, in Moa Bay, up to 20 cm scale may build up resulting in 5 days descale downtime per month. In addition, the iron residues cannot be utilized for ironmaking due to the presence of high content chromium (Ema and Harada, 1987; Owada and Harada, 1987; Takagi and Furui, 1987)."

Jan 1, 2012