Search Documents

By S. Amira

The corrosion behavior of high pressure die-cast and thixocast AXJ530 magnesium alloys has been investigated in 0.05M NaC1 solution at pH 6.0 using potentiodynamic polarization tests, electrochemical noise (EN) technique, electro-chemical impedance spectroscopy (EIS) and scanning reference electrode technique (SRET). The behavior of die-cast and thixocast specimens were compared using each of these techniques and the results discussed. Further tests have been carried out with die-cast AZ91D alloy to better compare and interpret the results. Experiments indicate that the thixocast specimens of AXJ530 alloy have a better corrosion resistance than those of die cast alloy in neutral solution.

Jan 1, 2006

By W. A. Hockings

This report describes a computer program for the solution of material balances in complex mineral processing flowsheets. The program, which is entitled MBS Metallurgical Balance System), evolved as the culmination of a series of material balance programs whose development began in 1967 at the Institute of Mineral Research, Michigan Technological University. The need for such a program became evident when the Institute became heavily involved in a large number of short-term pilot plant projects. Calculating material flows from analytical data by means of the standard two-product formulas grew increasingly difficult and time-consuming as the complexity of the flowsheets increased and as choices between conflicting analytical values had to be made. It was recognized that what was needed was a program that would assimilate all of the available data and calculate mass flow rates so that steady-state inputs and outputs would balance at each point in the flowsheet. Such a program should be capable of handling underdetermined, overdetermined and mixed systems, and when the given data are inconsistent, the program should adjust the data in such a manner that the adjustments are minimized. Missing analyses should also be calculated whenever possible. In addition to solving material balances, the program should be convenient to use and print out the results in a useful form. Thus, the inputting of data should be simple enough to be handled by relatively untrained personnel with diagnostic messages being printed out to identify errors and anamolous data when they occur. Most importantly, the program should produce well-formatted output which can be directly included into a report without the necessity of retyping. The proper spacing of table titles, column headings and the ability to control the columns being printed are important features in this respect.

Jan 1, 1977

By Emilie Lapointe, Fernando Famania

"A reliable determination of the in-placed cement factor, as defined by mass of cement over volume of final element of treated soil, allows the optimization of cement usage to achieve treated soil requirements. Cement determination tests were performed on soil-cement samples, both fresh (as per ASTM D5982) and hardened (as per ASTM C1084). This paper reviews the calibration work required for the D5982 determination of cement content by the heat of hydration method used on soil-cement samples obtained by wet-grabbing. Using the correlation curves in the field provides a rapid assessment of cement content hence optimizing the cement injection rate to match laboratory tests previously conducted. Cement determination tests on hardened soil-cement specimens from wet-grabs and cores were performed using the oxides method. Samples, both cored and wet-grabbed, were tested in a given cement-treated element, and in different soils to inform on the expected variation in cement content from field installation. Results indicate that both cement determination methods are valid for forensically determining cement contents and that they provide better assessment than the conventional field reporting methods. The methods can be used to optimise the cement usage as well as for Quality Assurance, especially when coring quality is poor.INTRODUCTIONThe degree of improvement, and inherent strength, which is attained in a deep-mixed soil is a function of many factors. The binder type, the existing soil, the mixing conditions and the curing conditions are the categories of factors influencing the strength of a given cement-treated soil as agreed by the deep mixing community and as summarized by the Coastal Development of Technology [CDIT] (2012). Given a site with existing soils and conditions requiring soil improvement using a given binder, the designer and/or contractor can control the mixing conditions. Mixing conditions are inclusive of the degree of mixing, mixing duration and the quantity of binder. Once a deep mixing method has been chosen to mix optimally the in-situ soil, the quantity of binder is the only remaining factor to be optimized. The quantity of binder, in the construction industry is commonly referred to as the field binder factor [ar] and defined by the mass of binder over the volume of soil treated with kg/m3 as unit. In research, the quantity of binder is referred to as the binder content [Cc] and expressed as a ratio of the mass of binder over the mass of dry soil mixed."

Jan 1, 2015

By D. J. Hains

IN this paper we shall examine the Why, Where and How concerning the agglomeration of iron ores and concentrates. Fig. l answers the questions @f why there is so much interest at the present time in the art of agglomeration. The use of sinter or pellets in the blast furnace has materially increased their rated •capacity. ':'President Hains Company Ltd. Engineering J. S. McMahon ( 1) reports an increase from 653 tons of .pig iron per day to 1140 tons of pig iron per day with the use of a 100 per cent sinter burden on one of his blast furnaces. In the United States the use of 100 per cent pellets has increased pig iron production from approximately 1800 tons per day to over 3000 tons pig iron per day (2). In our economic system the general objective is to produce more and better commodities cheaper. Fig. 2 shows the decrease in coke consumption with increased tonnages from the furnaces when using -

Jan 1, 1961

By Ofra Damm, v du Preez, D. van Vuuren, L. Simpson, H. Chikwanda

"South Africa is the world?s second largest producer of titanium bearing minerals, but apart from producing titanium mineral concentrate to form TiO2 slag, little further value is added in South Africa to mined minerals. Various studies were undertaken by both government and the private sector in an un-coordinated manner until 2007 when the South African Department of Science and Technology (DST) planned and adopted a national strategy to establish a local titanium metal industry through the research and development of key technologies that would provide a competitive advantage to such a local industry. The strategy entailed a two-pronged approach in the development of this capability, viz. simultaneous investments in the development of high-level human capital and technology in the fields of titanium metal powder production and downstream titanium metal powder processing technologies. To date significant progress has been made to establish research and/or pilot scale facilities in the following technical areas: TiCl4 production technology, titanium powder production technology, high energy milling of titanium powder, metal injection moulding facilities, rapid production of large components using laser additive manufacturing technology, investment casting of titanium, resource efficient machining of titanium and friction stir welding of titanium. Supporting technologies are also at an advanced stage through investments in titanium powder spheroidization and direct rolling of titanium powder. The intent with investment in some of these areas is not to develop new technology per se, but rather to establish local capability that will position South Africa to collaborate with other organisations in the world so that technologies can be acquired and transferred when needed in the future."

Jan 1, 2014

By James W. Collins

The bucketwheel stacker/reclaimer is suited for a variety of bulk material handling systems, especially those operating with stockpiles in excess of 30,000 tons. The bucketwheel stacker/reclaimer, although relatively new in the United States (first introduced here in 1964), has been successfully used in European countries since the early 1940's. Basically the machine is the outgrowth of the bucketwheel earth excavator and the traveling tripper boom type stacker. Since their introduction here they have achieved wide acceptance, especially with coal fired power plants. (Figures 1, 2, and 3.) The stacker reclaimer has been utilized in barge and ship loading/unloading facilities, and in the material handling systems for steel mills, where it has been used to stack and reclaim iron ore at rates up to 6000 tph stacking and 4000 tph reclaiming. They have also been employed at mine mouth power plants for the handling and storing of the plant fuel supply and to help balance the mining rate with the fuel consumption rate.

Jan 1, 1973

By Derrin A. Auerswald, Jacolien P. Wyethe, Nanne M. \/egter

Base and precious metal refineries often produce effluent solution and slurry streams containing between 50 mg/L and several grams per liter of base metals. Metals have historically been precipitated from these streams with lime to produce effluent streams at pH values between 8 and 9. This effluent treatment process generally does not remove alkali and alkali-earth metals or halides efficiently and with more stringent environmental legislation, more sophisticated effluent treatment plants must be considered which could for example incorporate sulphate removal with ultra-filtration, or the SavminTM process, followed by reverse osmosis for the removal of halides. The flowrates of effluents are often high and if base metals can be recovered before neutralization, the revenue generated from this stream can reduce the cost to produce clean water significantly, and in the case where high concentrations are disposed of, result in a profitable operation. As an add-on to an existing the plant the recovered metal is upgraded and recycled to the plant, but the production of a saleable metal can also be considered. Technology selection for metal recovery depends on the composition and flowrate of the effluent, but could incorporate resin-in¬pulp or other ion-exchange technology; precipitation as sulphides, hydroxides or carbonates; or solvent extraction. This paper describes, as a case study, the technology selection process and uses data from Zincor. Zincor is a division of Exxaro Base Metals (Pty) Limited, a subsidiary of Exxaro Resources Limited.

Jan 1, 2011

By O. Ditsele

Coal plays an important role in the energy needs of the World. Given its wide abundance and low cost, coal use is bound to increase with the growing energy demand. Despite its importance, there are growing concerns over coal?s environmental burdens, especially its contribution to greenhouse gas emissions. To ensure sustainable extraction and use of coal, opportunities for minimizing potential impacts from coal have to be identified and exploited. Whilst extensive work has been done on life cycle assessment of coal use, especially in electricity generation which uses the bulk of coal produced, there has been limited work focusing specifically on coal mining. This study aims to estimate the cradle-to-gate life cycle climate change impacts of coal from a surface coal mine in the United States. The study employs general principles of ISO standards for LCA.

Jan 1, 2010

By R. T. Jones

"Technical publications in the field of mining and metallurgy have existed for a long time. Recent developments in electronic publishing on websites make it possible to disseminate information more widely and cost effectively than before. Professional societies have an opportunity to serve their members and their industry by publishing high-quality peer-reviewed papers on their websites as well as in printed form. Older publications can be scanned, and optical character recognition can be used to provide searchable text. Various business models exist around this process. This paper outlines the approach used by the Southern African Institute of Mining and Metallurgy (SAIMM) to provide free open access to their journal papers and conference proceedings, as well as the work being done by OneMine.org to collect technical papers from a number of international societies and make them available to subscribers via a large database. An approach is outlined that should be of benefit to authors, readers, and society at large.INTRODUCTIONGeorgius Agricola (1494-1555) was not the first writer on the subjects of mining and metallurgy, but is well known as the author of De Re Metallica (‘of things metallic’ or ‘on the nature of metals’), a book that documents and illustrates the observations he made in the course of his extensive travels in the 1500s. Agricola wrote extensively about mining methods and metallurgical processes that were in place in the Middle Ages. The original Latin version of De Re Metallica was published in 1556, the year after Agricola died. It was translated into English by Herbert Hoover, a mining engineer and later President of the United States, and his wife Lou Henry Hoover, a geologist and classicist. The English version of De Re Metallica was published in 1912."

Jan 1, 2012

By B. L. Gibbs

The mining industry is constantly in a state of flux -boom or bust; mine openings and closings. Part of the reason is the nature of ore deposits -they are there or they are not. Once they are mined, they are reclaimed and the move is on to the next deposit. Risks are usually high, and payoffs can be great or not so great. Many factors go into making a property payoff, and mining companies are continually searching for ways to remain profitable as long as possible. Computers and the people who can make them work are one of the ways available to improve productivity and ensure this happens. Computers have been used in the mining industry for the last 30 years (and more in a few cases). During the past 10 years, the explosion of micro-computing has changed how many mining companies do their work.

Jan 1, 1993

By M Lovitt, T Hewitt

The extraction of drawbells in Lift #2 at Northparkes Mines E26 orebody was achieved by single shot blasting, enabled through the use of electronic detonators. This paper discusses the designs considered at the time of the feasibility study and the various changes made to these designs prior to and during the construction phase of the Lift #2 block cave. Operational issues encountered are highlighted, as are ways in which these were overcome. The amount of personnel utilised to mine the drawbells is also covered. Lists of design and operational considerations to be used for drawbell extractions have been included.

Jan 1, 2005

By Satoshi Itoh

Phase equilibria and activities of the components in the liquid lead-antimony-oxygen ternary system, which is of fundamental importance for discussing the' recovery of lead and antimony from a used lead-battery, have been investigated at 1173 and 1223 K. The two liquid phases of metal and oxide were observed at the temperatures studied, and the tie lines indicating isoactivities were determined. The activities of PbO, SbO1.5 and Sb2O3) in the PbO-SbO1.5 and PbO-Sb2O3 pseudo-binary systems were then obtained by applying the Gibbs-Duhem equation to the phase relation of metal-oxide equilibrium. Both in the pseudo-binary systems the activities exhibit negative deviations from Raoult's law. The vapor pressures of lead, antimony and lead oxide, antimony oxide were calculated by using the activities of the components in the lead-antimony-oxygen ternary system. As a result, an oxidation of antimony concentrated in an anode slime followed by evaporation as antimony oxide Sb406 was found to be considerably effective for the recovery of lead and antimony from a used lead-battery.

Jan 1, 2003

By Pesic. Batric

A novel chitosan-pyridoxal-epichlorohydrin was synthesized and evaluated in our laboratories. The evaluation was achieved by performing kinetic and equilibrium studies of copper sorption. The parameters examined were pH, temperature, concentration of copper, particle size and selectivity of copper sorption against iron, zinc, cadmium and cobalt. It was found that pH was the most important parameter, and sorption of copper increased with pH increase in the range pH 2.5-6.0. The low activation energy of the sorption reaction, 1 1.13 kJ/mole (2.66 Kcal/mole), showed that temperature was not an important parameter. The synthesized chitosan was selective against iron, zinc, cadmium and cobalt. The selectivity with respect to last three metals was achieved by the kinetic difference of sorption, as sorption of copper was much faster than for other metals. Iron (Fe2+) does not adsorb on chitosan. The mechanism governing the sorption of copper is intraparticle diffusion. This finding was supported by the dependance of copper sorption on the square root of time, the low activation energy, and the fit of experimental data in the diffusion through the product layer equation.

Jan 1, 1994

By R. I. Kraydenko, A. N. Dyachenko

"The possibility of SiO2 5N production by staged purification of ammonium hexafluosilicate (NH4)2SiF6 is discussed. High-purity silicon dioxide can be obtained with fluoridation of quartz concentrate by solid NH4F at 100 °C, with further sublimation of the product at 320 °C, its dissolution, ammonia hydrolysis, filtration and drying of SiO2•nH2O. This is accompanied by regeneration of the processing reagent - NH4F.INTRODUCTIONProduction of high-purity silica-5N (SiO2 content over 99.999%) is an important and urgent task of the modern chemical industry. This material is used in the manufacture of optical glass, optical fibers for internet cables, silicon for solar power and electronics.Quartz concentrate is raw material for the production of silicon dioxide. The existing technologies of synthetic silicon dioxide were introduced in the mid-twentieth century. These methods are energy-consuming, multi-step and do not meet stringent environmental requirements. In fact, as some conventional technologies became obsolete; it became necessary to develop new methods for the production of synthetic silica. We believe that the fluoride technology of processing of quartz materials by ammonium fluoride is the most promising direction.In industry, silicon dioxide marked ""Silica White"" is obtained by liquid-phase method. The method consists of the precipitation of amorphous silica from sodium silicate solutions with acids. The resulting product is filtered, washed and dried. Depending on the deposition conditions and nature of the coagulant the ""Silica White"" is acidic, neutral or alkaline. The dry product is subjected to grinding. The degree of dispersion and porosity of the particles of Silica White depends on the nature of decomposition agent (a substance that decomposes the silicate) and coagulant, conditions of sedimentation, filtration and drying. During the drying process the silica particles are sintered into aggregates of a few millimeters."

Jan 1, 2012

By Alan Rhodes

This study is initiated to investigate the efficiency of separation of mineral slimes using electroflotation as compared to that of column and conventional flotation techniques. Important parameters such as collector concentration, pH, current density, aeration rate, etc., have been studied. The results indicate that electroflotation can be used more efficiently in processing rutile slimes (10 µ) under certain operating conditions.

Jan 1, 1982

By Robert Perlman

The paper point out which area of conflict between international companies y and less developed countries. The lost year the lees developed countries were received invesment very low as to that they can grow and expan. Likewise the foreign investment led easily to its fair share of explicitation and bloodshed. In the same way, the alternative to a particular development being undertaken by foreign capital is either that investment does not take place at all or that capital resources are diverted from somewhere in the domestic economics, in which case some other piece of investment does not take place.

Nov 20, 1969

By N. Aslin, G. Heferen, H. DeWaal

"Mount Isa Mines (MIM) acquired a reputation for the successful application of R&D to develop break-through technologies for the mining industry starting in the 1978’s through until the early 2000’s. The ISAPROCESSTM tank-house technology has been licensed to copper refineries throughout the world, and a significant per cent of the world’s copper is refined using this technology. Since development in the late 1980’s more than 20 ISASMELTTM copper and lead smelting furnaces are now installed in countries around the world. Jameson Cell flotation technology developed jointly by Mount Isa Mines and Professor Graeme Jameson is widely used in the Australian coal mining industry and increasingly in the base-metal and gold industry. The IsaMillTM’s developed at Mount Isa and McArthur River made it possible to develop the McArthur River and George Fisher orebodies and has been successfully implemented into base metal fine grinding applications around the world. The most recent commercialised innovation is the atmospheric leach Albion ProcessTM with its supersonic HyperSpargeTM gas sparger, is being adopted as a solution to the increasing complexity of orebodies. MIM’s contribution to the industry was significant given the size and the remote location of its operations with Townsville Copper Refineries more than 1350 km and Mount Isa 1800 km from the nearest state capital of Brisbane. This paper will briefly discuss the development of each of these technologies and why MIM – now owned by Glencore - was so successful innovating and developing such technologies over a period of nearly 40 years.INTRODUCTION Mount Isa is located in the Gulf Country region of Queensland about 1800 kilometers North West of Brisbane (see Figure 1). It came into existence because of the world class mineral deposits found in the area. In 1923 the orebody containing lead, zinc and silver was discovered by the miner John Campbell Miles. Mount Isa Mines Limited (MIM) was founded in 1924 to develop the minerals discovered by Miles, but production did not begin until May 1931. It paid its first dividend in 1947 after 16 years of troubled production. In 1954 the 1100 copper orebody was discovered and with rapidly rising reserves during the 1950’s and 1960’s led to the construction of new concentrators to treat lead/zinc/silver ores in 1966 (#2 concentrator) and copper ore’s in 1973 (#4 concentrator). The difficult nature of the Mount Isa lead-zinc orebodies has meant that the company had always needed to be at the forefront of mining technology. In the 1970’s through to the 1990’s, it became a world leader in developing new mining techniques and processing technologies as a response to declining metal prices and rising costs. Mount Isa has been smelting copper since 1953 and lead since the early 1930’s. Copper Refining at Mount Isa’s fully owned subsidiary of Copper Refineries Proprietary Limited (CRL) had commenced operations in 1959."

Jan 1, 2018

By R. Khanna, K. Hyun Ko, A. J. Berkovich, J. Hook

"The co-pyrolysis of synthetic polymer polyethylene terephthalate (PET) and agricultural wastes (naturally occurring polymer-macadamia nut shell) was investigated in the temperature range 473K to 1273K using a horizontal furnace with an aim to understand their thermal degradation under isothermal conditions. In-depth characterization of pyrolysis residues was carried out using x-ray diffraction (XRD) and solid state nuclear magnetic resonance (NMR) for carbon structure, and through determination of the concentration of unpaired electrons using electron paramagnetic resonance (EPR). In previous studies, it has been found that PET thermally decomposes ~ 650K-700K, releasing (~80 wt % of initial weight) gaseous products due to random chain scission. In the case of macadamia nut shell, three types of byproduct can be obtained from pyrolysis: char, tar and gaseous products. In the co-pyrolysis of macadamia nut shell with PET in 50-50 wt% ratio, total product weight ratio could be modified with the addition of PET acting as a hydrogen source. This is because a recombination of thermal cracking products of cellulose could be suppressed by hydrogen from PET, which will later lead to an enhancement of tar formation. In addition, pyrolysis around 673K is sufficient for bond cleavage to occur in cellulose and lignin leading to the formation of negatively charged activated carbon with high surface area, providing bonding sites for volatiles evolving from PET. Therefore the co-pyrolysis may be able to enhance the product yield (tar/char/solid carbon residue) along with a reduction in the release of gaseous products. During the co-pyrolysis, temperature was found to have a significant influence on the kinetics of thermal degradation and solid residual by-products after co-pyrolysis.INTRODUCTIONPlastics are being used worldwide in a wide range of applications in the modern society; their usage has resulted in increasingly a massive waste problem. The production of most synthetic plastics requires hydrocarbons that are produced from petrochemicals derived from fossil oil and natural gas, a non-renewable source (Speight 2011). Currently, plastic manufacture utilizes ~4% of world oil and gas production, and it is expected to drive further increases in petroleum demand by 1-2% due to their large volume of manufacture (Hopewell, Dvorak et al. 2009). Landfilling and incineration of plastic waste are the two main routes to plastic waste management (Encinar and González 2008). In Australia, only 10% of waste plastics were recycled in 2006 (White and Hyde 2011). This means that large amount of fossil fuels from plastics has either been simply burned for energy recovery or buried in the ground. There is an urgent need for developing alternative avenues for recycling waste plastics. Our group at UNSW has carried out extensive research on the recycling of waste polymers as carbon resource in steelmaking including slag foaming and carbon dissolution from waste plastics into liquid steel at 1600°C; the effect of basic plastic characteristics such as chemical composition, structure, bonding network etc. was examined (Sahajwalla, Rahman et al. 2009)"

Jan 1, 2012

By I. R. M. Chaston

Abstract. This paper puts forward the concept of 'radial' plant layout where all crushing, milling and treatment operations are preferably concentrated in one central area and these separate stages are connected by radiating conveyors to and from outside storage areas. This system is contrasted to the more customary system of 'linear' plant layout where the crushing, milling and often the treatment operations follow one after the other in separate buildings. The radial system simplifies and improves contral and supervision to a very considerable extent and can lead to a form of continuous plant operation with the separate sectors shutting down in succession for necessary maintenance while maintaining the overall plant operation. The paper is illustrated with example: from past and recent diamond treatment plant practice in South Africa which demonstrate the reduction in plant labour achieved by this system. Previous objection to this type of layout on the grounds that it inhibited plant expansion are shown to be unwarranted. Radial Layout for Increased Treatment Plant Productivity A great deal of time and trouble is spent by highly qualified and experience( metallurgists in developing the right treatment process for a given ore. This process is then often expressed in a treatment flowsheet of the type shown in Fig. 1 which shows a typical diamond plant. This flowsheet, when completed, is commonly handed over to the mechanical engineers who then design the layout of the equipment indicated on the flowsheet and produce the working drawings upon which the detailed construction of the treatment plant will be based. It is an unfortunate fact that the tedious and time-consuming juggling of equipment and inter-plant transportation is often left to hard-working draughtsmen who, however capable' in their field, lack practical experience in the day-to-day operation and maintenance of the treatment plants they design. As a result many plants have been produced which, while they satisfy the requirements of the flowsheet with minimum capital requirements, cost far more than should be necessary to op¬erate and maintain. It is often possible to change individual items of equipment which do not achieve the performance required of them, but it is usually extremely expensive to change the basic layout of the plant if this should be found to be unsatisfactory. It should therefore be recognised that great care and attention should be spent on consideration of the basic layout of any treatment plant and that the views of both designers and operators should be fully regarded before settling upon the inevitable compromise dictated by the varying requirements of process-engineering and economics. It is unfortunate that this important subject receives such scant regard in the standard ore dressing text books and hand-books, being usually dismissed in a few paragraphs.

Jan 1, 1977

By G Fahey, S Rose

"Mining geology as a defined profession is only about 100 years old. The successful modern mine geologist needs to be a multidisciplinarian, but also needs to maintain a focus on the key outputs of the role. The technical skills needed in the role have increased as mining methods move to increasingly mechanised techniques. As well as being the guardian of the orebody and ensuring minimal dilution to expected ore grades, the mine geologist should be competent in the 12-point mine geology process. The mine geology process should include:a statement of purpose (a ‘mission statement’)geological mapping/logging system that supports consistent and regular geological data collection, storage, and interpretationsampling system that can produce representative samples and fits in with the mining scheduleassay database with relevant controls to ensure only ‘clean’ data is loadedsimple quality assurance / quality control (QA/QC) system for samples and assays, with a response process to react to out of specification resultsconsistent method of exporting, visualising, processing and interpreting assay data to create mining blocksdevelopment sign-off system so that all development and stoping is controlledproduction tracking system to monitoring and reporting what ore and waste volumes have been moved from the face, to any intermediate stockpiles, the run-of-mine (ROM) pad and into the crusherreporting system for daily, weekly and monthly reporting of tonnes and gradesdocumentation so that the grade control system has simple, but effective descriptions of how it works, who has responsibilities, and authorities, and be easily maintainedreconciliation system to compare resource and reserve to grade control and to mined and milledtraining system so that the geology team can quickly become competent.In this paper, the authors discuss the requirements of each point, and comment on common shortfalls observed by them over several years’ experience on producing mines worldwide.CITATION:Rose, S and Fahey, G, 2014. Modern mining geology, in Proceedings Ninth International Mining Geology Conference 2014 , pp 461–466 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 18, 2014