Search Documents

By Xin-liang Gao, Qing Li, Gui-qin Fu, Duo Jin, Miao-yong Zhu

"Optical microscope together with alternative wet-dry cyclic accelerated corrosion tests and XRD, SEM were employed on bridge weathering steel samples with different Mn and Ni contents which were vacuum induction melted and rolled to study their effects on the microstructure and rust layer evolution in er' containing condition. The results show that the microstructure is mainly ferrite and pearlite when Mn and Ni contents are 0.75 %, 0.42 %, respectively. Both the increase of Mn and Ni contents will make pearlite disappear while granular bainite appear, meanwhile the grain size decreases. With the increase of Mn content, the corrosion rate decreases in the initial stage, but the effect becomes little in the later stage. The increase of Ni not only improves the corrosion resistance of steel base at the initial stage but also hinders the tendency of further corrosion. As Mn content increases, a-FeOOH contents in rust layer decreases. With increase of Ni content, the content of a-FeOOH in the rust increases while that ofy-FeOOH decreases.IntroductionWeathering steels had been ~radually applied in manufacture of bridges owing to reducing the corrosion rate remarkably [I- l .Good weldability was needed for high performance bridge weathering steels. Since carbon was thought to be bad for weldability, low carbon content steel was adopted and Mn was added to amend the mechanical strength loss. Some scholars[6, 7l believed that Mn was beneficial for increasing corrosion resistance performance of the steel in marine atmospheric environment. Some scholars [S, 9l thought that Mn had little effect on corrosion resistance in marine atmospheric environment. Presently, the effect of Mn on bridge weathering steel in marine atmospheric environment still remained poorly understood. Ni was considered to be beneficial for increasing corrosion resistance performance in marine atmospheric environment [JO-l4l However, the high cost limited its application range. What would bring to the rust and corrosion by decreasing Ni content needed further research.Most researchers assumed that microstructures only affected the corrosion behavior of bare steel. But the study of Guo et al. P5l showed that the homogenous microstructures were beneficial for the corrosion resistance of steels. The effect of Mn, Ni content change on microstructure and microstructure on corrosion still remained poorly understood. In the present work, the effect of Mn and Ni on the microstructures of steel matrix, as well as the microstructures on the rust and corrosion was investigated."

Jan 1, 2014

By H. M. Breza

Recovery of phosphate concentrate has received increased attention as the existing mine and plant production capacity limitations of the Texasgulf Inc. Aurora, North Carolina Mine are reached. Improved mining techniques and mineral processing of waste streams offer a potential to increase overall phosphate production without major expansion of the Mining facility. Innovative processes have been or are being identified to maximize pit mining recovery and to minimize losses in waste streams, resulting in more effective use of the valuable phosphate natural resource. This paper will describe the various continuous recovery improvement programs being implemented to achieve this goal.

Jan 1, 1994

By A. A. Novoselov, U. Kelm

"Large volumes of mine tailings accumulated in surroundings of porphyry copper deposits represent a growing threat to environment. They contain significant concentrations of toxic metal and metalloids which can contaminate river runoff, ground waters or can be transported by wind. Both extreme pH of fluids in tailings impoundments and high surface areas of processed mineral grains provide their increased reactivity. As a result, during only a few decades, As, Cu, and Mo can be mobilized, redistributed through the tailing column and accumulated through post-deposition leaching, evaporation and contamination with natural fluids. Those processes are reflected in the forming of secondary minerals. Gypsum, Fe oxides/hydroxides, efflorescent salts and clay minerals are typical alteration products in tailings. Here we present the results of reactive transport simulations implemented on the base of PHREEQC and SUTRA codes. The one-dimension model emulates the mass balance between rainfall, evaporation and subsurface runoff, the kinetically- and thermodynamically-driven dissolution of tailing minerals, advective and diffusive transport of tailing fluids, and precipitation of secondary phases. A typical tailing column is composed of four unequal layers with predominance of (i) evaporation, (ii) secondary mineralization above, (iii) below water table, and (iv) near the bottom of dump. Those horizons are characterized by contrasting pH, chemical composition and bulk mineralization of pore fluids, distinct accessibility of atmospheric oxygen and, as a consequence, distinct intensity of sulfide oxidation. The modeling and its verification on Chilean tailings impoundments reveal the complexity and high rates of secondary mineralization. The accumulation of toxic alteration products is controlled by fluid transport through the tailing column induced by both rainfall/evaporation and exchange with subsurface runoff. The geochemical modeling is a powerful approach which allows comparing the processes in tailing deposits produced by distinct flotation regimes and providing the long-term predictions of their environmental impact as well as identifying sectors of tailings for possible re-processing."

Jan 1, 2018

By E. Trickey

In the mining industry there exists a constant drive for increased safety and productivity and decreased operating costs. This acts as a driver for implementing advanced technology. As more and more mining operations turn to new technologies, an observed bottle-neck for technology advancement has been the limitation of machine vision solutions available. LiDAR has been seen as a possible solution to the machine vision problem. In the past, a few studies on machine vision solutions have been undertaken by various groups involving scanning laser range-finders and millimetre-wave radar. These studies have done little more than highlight the limitations of both technologies in the mining environment. Little work has been done, however, exploring the applicability of LiDAR imaging technology for mining applications. Neptec Technologies Corp. has developed an obscurant-penetrating LiDAR (OPAL) sensor technology which overcomes the limitations faced by traditional LiDAR sensors when operating in a dusty environment, as well as advanced 3D real-time intelligence (3DRi) data processing algorithms that enable the real-time exploitation of 3D imaging data with sensors mounted on moving vehicles. Working with Teck Resources Ltd. and Barrick Gold Corporation, Neptec is adapting the OPAL sensors and 3DRi technology to mining applications. This paper highlights a number of real-time OPAL/3DRi based mining applications demonstrating how this technology overcomes the limitations of traditional LiDAR to provide a real-time machine vision solution that supports mine machine autonomy.

Aug 1, 2013

By James M. Neilson

In contrast to the rather generalized title of this paper, the subject of discussion will deal with two specific cases of sliding in glacial lake clays in northern Michigan. The slides in question occurred on lands owned by the Upper Peninsula Power Company a short distance south of Lake Superior. Slope failure problems have plagued the Company's operations for many years. It is hoped that this paper may provide some insight into the causes and possible mechanisms of clay slides in general as well as providing details of the two slides specifically cited. LOCATION The Upper Peninsula Power Company's Victoria facilities lie in section 29, T. 50 N., R. 39 W., in Ontonagon County, Michigan. The power site is situated on the West Branch of the Ontonagon River, approximately five miles southwest of the town of Rockland and only one mile to the southeast of the old mining location of Victoria. The area lies wholly within the Precambrian Shield and it is geologically similar to adjacent parts of Wisconsin, Minn¬esota, and Ontario. (Figure 1). THE VICTORIA HYDROELECTRIC SITE The Victoria hydroelectric power facilities were constructed in 1930 on a portion of the West Branch where meanders are conspicuously developed. The generating station is actually sited on an abandoned meander at a place where valley widening has occurred. Water is conducted from Victoria Dam through a 6000-foot, 10-foot diameter wood stove pipe - through a surge tank - and into the powerhouse where

Jan 1, 1971

By X. K. Lan

The greater demand for high-quality large-diameter crystals has led to the robust idea of a free- flying solar-powered furnace satellite, whereby the buoyancy-driven convection effects are almost nonexistent, and diffusion-controlled crystal growth with minimal radial segregation is promoted. In the proposed solar furnace, a paraboloid of revolution imaging concentrator is used to focus the sun's radiation onto an-ampoule which holds the solid charge to be processed. The charge will start melting in the vicinity of the focal point, after which it is translated in order for the melt to resolidify as a single crystal. A ray-trace method has been developed to determine the incident concentrated solar heat flux on the ampoule surface for a perfectly-aligned configuration with an incoming columnated beam. A transient 2- dimensional conduction problem with phase change is formulated, which is solved using the commercial code FIDAP. Results highlighting the feasibility of growing GaAs, Ge and Si crystals with diameters of the order of 20 cm using the solar furnace satellite concept are presented. The transient temperature fields within various charge materials are quantified.

Jan 1, 1994

In cold regions rinsing of spent cyanide leach heaps is stopped during winter and is resumed again after snow melts. The effect of this idle time on the overall cyanide removal process was studied in this work. Samples were collected for rinsing tests from one heap at the Ryan Lode Mine of Citigold Alaska, Inc., near Fairbanks. The material was tested for cyanide removal a large column, 1.22 m high by 20 cm square, and in a small column, 1.22 m high by 10 cm in diameter. The rinse water was analyzed at regular intervals to determine the rate of cyanide removal from the solids. It was found that diffusion plays a major role in the removal of cyanide from the ore particles. Calculations showed that the insulating effect of the snow cover on the heap provides an excellent moderates the interior temperature of the heap, and would be expected to help the progress of the diffusion reaction during winter. The result expected result wil1 be higher cyanide values reporting to the rinse water after snow-melt.

Jan 1, 1993

By Henry Hu

In high pressure die casting processes, proper control of temperature die yields a high casting production rate and superior quality components, Die temperature is usually influenced by various die design and process parameters such as size and location of intemal water cooling lines, flow rates of cooling lines, and pouring temperature of molten metal. Among them, the cooling water flow rate plays a major role in controlling thermal pattern of the die_ In order to develop an effective control strategy, data of local die temperature must be collected and analyzed, In this study, a PC-based data acquisition and control system (DACS) for die temperature control has been designed, and established, The developed DACS has three input channels for temperature signals and one input channel for water flow rate signals, as well as one output channel for a water pump, and is capable of displaying data in both curve format and value format. Implementation of the DACS in a laboratory setup has also been attempted, It should be pointed out that more advanced control mechanisms can be potentially integrated into this system in future,

Jan 1, 2003

By Ebrahim Tarshizi, Livernois Ryan, Emily Sarver, Zoe Scopa, Robert Setterlind, Leah Frost

"The mines of the future present a host of challenges, which may appear exciting or daunting, depending on one’s perspective. Whether some sectors of the public recognize it or not, the demand for raw resources is not going away any time soon. In fact, it is rising, as the global population grows, urbanizes and attempts to steadily increase quality of life. Yet, at the same time that much of the highly developed world is calling for greener goods, reduced consumption and cleaner production, in other areas there are cries for clean water and sanitation, consistent energy supply, access to health care and education, personal security and support for basic human rights. The balancing act for sustainable development of our global society is, indeed, precarious and the mining community is a key player. Fortunately, many industry members have accepted this role and the responsibility to provide leadership and a solid foundation for progress. Looking ahead, we need new generations of leaders, including many mine engineers who are ready to tackle all sorts of complex problems.There are tremendous needs just for technological innovations. Increasingly tough deposits will require that the industry continues to expand scale toward “mega pits” and “super caves;” fully develop unconventional recovery techniques like in situ leaching and gasification or deep-sea extraction and seriously consider off-earth endeavors. Such work will take entirely autonomous equipment, novel separations, processing and recycling methods, and systems that can withstand extreme physical conditions, just to name a few. It will also take a level of systems integration never-before seen in the mining industry, complete with big data issues, sophisticated predecitve analytics and modeling efforts and cyber-security challenges.Moreover, increasingly complex environmental problems will require creative solutions. Addressing issues like pollution control across multiple media, emerging contaminants, optimal management of wastes, selective mining and shared use of resources between mine operations and surrounding communities and ecosystems are among the top priorities. Really, a complete paradigm shift must occur, such that the focus is on overall improvement of environmental conditions, rather than minimization of impacts. A similar shift will be required in the social realm. How can miners be safer and healthier on-site and off? How can the industry contribute to communities such that they are better off, now and longterm, for having a mine next door? How can artisanal mining practices be transformed to also contribute to sustainable development? How can the industry’s work be a factor in increasing economic and political stability? How can the public understanding of raw resources and the need for mining enterprises be improved?Given the coming challenges, there is no doubt that the mine engineers of the future will need highly diverse skillsets — meshing traditional and contemporary competencies to a degree not previously considered in mining, or most others fields. To be sure, the scope and scale of mining projects make them wholly different than most other engineering work, aside from perhaps the largest civil and urban development projects. While on-the-job experience will continue to be essential, formal education programs (i.e., at post-secondary institutions) must lay critical groundwork."

Jan 6, 2017

By W. G. Campbell

"The region discussed comprises approximately eight million acres spreading across the Arctic Circle in Yukon and North West Territories.Encouraged by four years of surface geological and geophysical work, which strongly suggested that suit-able conditions existed for the entrapment of oil and gas, a decision was reached to drill. In due course two holes were drilled; Eagle Plains No. 1 drilled to 9589 in 1957-8 and Western Minerals Chance No. 1 spudded in 1959 is being deepened this year.Thick sections of sedimentary rocks occur on both sides of the Richardson Mountains, however, most of our activities have been concentrated to date on the west side in the Eagle Plains basin. Here are found stratigraphic units ranging from Precambrian to Tertiary age. The drilling of the two exploratory wells proved the presence of these strata at depth and have confirmed the presence of promising structures. A geological cross-section across Eagle Plains presents an interpretation of these conditions.Physical and engineering aspects of exploration in the northern Yukon and North West Territories are de-pendent largely upon seasons and transportation. Reconnaissance gravity and surface geologic mapping by air presents no serious problems. However, seismic operations on the ground are greatly affected by the season, presence of permafrost and mobility of equipment.The actual drilling of the hole may well be the simple part of a wildcat undertaking once equipment and supplies are on location. Over-all planning, assembling supplies, transporting equipment and personnel seems to be the real job. Serious consideration must be given to per-ma-frost effect in the drilling pro-gram and on surface installations as well.Programming for -the various exploration activities should be under-taken well in advance of the actual doing. Considerable extra costs may be the results of crash programs. Costs are high, and the rewards uncertain. Economic evaluation is based •on the long term outlook."

Jan 1, 1960

By Elena Chiriotti, Federico Valdemarin, Jan Cenek

"SUMMARY The “28 May Station” is the only transfer station between the existing Green and Red metro lines in Baku. As part of the huge development strategy of the metro network, the complete separation of the existing underground lines has been planned at this location, in order to simplify the operation of the future metro system. The extreme challenge of the project is represented by the need of achieve the separation of such lines over a breakdown of the operation of just five weeks. The lack of direct access from the surface, a complex geology with artesian water layers, a congested underground space and sensible buildings represent additional constraints. The chosen design solution consists in creating a complex steel pipe jacking frame around the operating tunnels and then excavating under such frame two large caverns where the separation of the existing lines and the construction of the new metro tunnels will be achieved. Soil treatments have been conceived to mitigate the geotechnical risks and to reduce possible impacts on the existing structures. The paper illustrate the challenges of this extraordinary project, one of the most complex underground structures under study, the design solutions and the risk management approach used to manage the complexity and to design the mitigations measures. INTRODUCTION The metro network in the capital of Azerbaijan is rapidly growing together with its metropolitan area. The beginnings of the existing metro system started in Baku in 1967 in Soviet times. To date, only two lines (Green and Red) are in operation with a total length of 34 km, including 23 stations. The future network will be much wider: besides the construction of three completely new lines and the extension of two existing lines, the whole metro project includes the development and modernization of the existing metro sections. A consortium formed by Systra (leader), Mott MacDonald (Praha) and Saman (Korea) awarded the contract for the preliminary and detailed design of infrastructures for the extension of Baku Metro Network. This extension consists in 83 km of new lines and extension of existing lines. As part of this modernization project, the connection of the Green Line at the 28 May / Cefer Cabbarli Stations, focus of this paper, represent also it’s ""Achilles' heel"" given that the already very congested system have only one transfer station."

Jan 1, 2016

By F. D. Forgeron

"ONE OF THE FIRST DOCUMENTED APPLICATIONS of soil geochemistry in the Canadian Shield was that carried out by Chisholm in the Kenora district in 1949. This survey proved successful in outlining sulphide-associated gold veins utilizing cold-extractable metals. Since then, mining companies, government agencies - both provincial and federal - and universities have conducted soil investigations. Some of the results are documented in publications, others are on open file in provincial and federal mines departments and, unfortunately, many other investigations with both successful and unsuccessful results are buried in company files or have been discarded. This paper deals with soils within the scope of chemical studies of overburden in the Canadian Shield. The subject is a broad one and some definition is required. The soil investigations discussed herein are those aimed at the testing of specific targets more or less in the source area. This definition distinguishes soil investigations from other overburden studies which commonly monitor metal accumulations at some substantial distance from the metal source. Naturally this distinction is relative, because in many instances there is overlap."

Jan 1, 1971

By Sergio Castro, Janusz Laskowski

In the flotation in highly concentrated electrolyte solutions not only ionic strength but also chemical composition, flotation pH and mineral properties play an important role. As a result an improvement or depression may be observed. A strong improvement in the floatability of hydrophobic bituminous coals and other inherently hydrophobic minerals is characteristic for the "salt flotation process", which is carried out in concentrated electrolyte solutions at natural pH and without addition of any flotation reagents. However, pH is a key factor when saline and hipersaline waters with hydrolyzing metallic ions are used as process water. In the case of flotation of Cu-Mo sulfide ores in seawater, molybdenite is strongly depressed by the Mg2+ hydrolysis products when pH is raised to depress pyrite. Process water with a high content of Mg2+ and Ca2+ ions, and this also includes seawater, have deleterious effect on the anionic flotation of industrial minerals with fatty acids. The flotation of potash ores is carried out in NaCl-KCl saturated brine (6-7 mole/L of NaCl and KCl) with the use of long-chain amines. Such a high electrolyte concentration changes dramatically the amine Krafft point making the collector insoluble in brine; its mode of action entirely differs from that in conventional flotation processes.

Jan 1, 2014

By J Hadjigeorgiou

The stability of open stopes in underground hard rock mines is influenced by several factors including the shape and size of the excavation, surrounding stresses as well as the degree of jointing. This paper presents a design methodology for stope analysis in jointed rock masses. The proposed approach relies on geological structural data to construct realistic three-dimensional joint network models. The stability of an open stope is determined based on a limit equilibrium analysis.

Jan 1, 2000

By R. Hogg, T. F. Dumm

"A procedure for evaluating the size/specific gravity distribution of ultrafine coal and the distributions of sulfur and ash with respect to particle size and specific gravity is described. The procedure is essentially an extension of the conventional coal washability technique in which special precautions are taken to ensure particle dispersion in the heavy organic liquids, centrifuges are used to obtain adequate separation rates, and micromesh sieves are used for size separation at fine sizes. An example of the application of this technique to the evaluation of the extent of liberation of sulfur and ash in a coal sample ground to 90Z passing 200 mesh (74 um) is described.INTRODUCTIONIn order to determine the potential for deep cleaning of coal by fine grinding to liberate sulfur and ash-forming minerals, it is necessary to obtain data on the distributions of these species by size and specific gravity. In conventional coal processing operations, this information is obtained by means of a standard ""washability"" analysis. Attempts to extend this procedure to ultrafine coal, however, have generally been unsatisfactory and have often led to unreliable and inconsistent results [11. The present authors have described a modified washability procedure in which cumulative specific gravity fractionation is combined with sub-sieve size analysis (by laser diffraction/light scattering) to determine the particle size/specific gravity distribution of ultrafine coal [2]. Unfortunately, because this technique does not involve separation of the individual fractions, only limited information can be obtained on the specific distributions of sulfur and ash.The objective of the work described in this paper was to develop and evaluate a procedure for size and specific gravity fractionation of ultrafine coal and to use conventional analyses for sulfur and ash to determine their relative distribution in the coal. The procedure is essentially a simple extension of the standard washability analysis [3] but incorporating special precautions for treating ultrafine particles.EXPERIMENTAL Material The material used in the development and evaluation of the ultrafine coal fractionation procedure was a medium volatile bituminous coal from the Lower Kittanning seam. A sample of the coal (nominally - 1/4 inch), obtained from the Penn State Coal Data Base, was ground to 90% passing 200 mesh by the following two-stage grinding procedure: About 2 kg of the as-received coal were ground to about 30Z passing 200 mesh in a Model 4-E Quakertown mill (""coffee grinder""). About 1 kg of this product was then ground to about 90Z passing 200 mesh in a Holmes Model 300 Pulverizer."

Jan 1, 1989

By David Yang

Commercially available flotation technologies for recovery of mineral fines have remained essentially unchanged for several decades. Recent studies have focused simply on improving mechanical and open column cells. Such studies have explored different control strategies and have aimed to improve reagent selectivity, fine air bubble generation and particle-air contact. However, no study has questioned whether current techniques are the most efficient technology for recovering mineral fines. Given that both mechanical and open column cells have a widely accepted carrying capacity limitation, the lack of extensive research into an alternative technology is surprising. Most recently, open column flotation has become an entrenched technology, and it is undermining the efficient recovery of mineral fines worldwide. An alternative exists. Packed column flotation overcomes the above-stated problems as the technology surpasses the carrying capacity limitation of current means by several-fold and almost always achieves the best performance in many comparative pilot tests and full-scale plant operations. Filling a column with packing plates creates a network of sloped walls capable of supporting a froth bed many times deeper than conventional machines. Having froth up to 75 percent of the total column volume tolerates all feed changes encountered in the plant environment and permits maximum flexibility in concentrate quality control. Furthermore, its scale-up is straightforward by increasing column volume or the number of interconnected small cells. As the air breaks upon rising and is distributed horizontally through packing plates, the air spargers can be replaced with a simple blower, resulting in considerable savings in operation and maintenance costs. Packed flotation technology provides a break-through solution for the separation of fine and ultra-fine minerals. Its simplicity, superior performance, and low cost structure make it an appealing alternative to current technologies and allow greater flexibility in downstream processing. Future industrial applications include a wide variety of metallic and non-metallic ores. This paper focuses on some recent scale-up campaigns for nickel and copper sulphide flotation applications compared directly to conventional equipment.

Jan 1, 2014

By N. H. Coates

A small, special-purpose centrifugal compressor was developed to circulate 60 pounds per hour of helium at 1,000° F and 250 psig because standard, commercial units were not available. Performance characteristics of this compressor were determined at helium flows of 2,000 to 18,000 std cu ft per hour, pressures of 100 to 250 psig, and temperatures of 100° to 1,000° F. This range is 2 to 90 actual cu ft per minute. Several graphs show the adiabatic head developed by the compressor over this wide flow range at various combinations of temperature and pressure. A compressor performance map relates pressure ratio to mass flow, temperature, pressure, and speed. This map can be used to accurately predict compressor performance factors within the range of operating conditions covered by the experiments.

Jan 1, 1963

By Robert B. Haagensen

While light optical microscopy has long been employed by the mineral processing industry, there has been a tendency to shy away from its use for all but the most exacting purposes. Despite the usefulness of micros-copy in solving a wide variety of problems, the response to such work is often less than enthusiastic primarily due to time considerations. Microscopical techniques are therefore often relegated to the "ivory tower" and their direct and practical application to everyday problem solving over-looked. The purpose of this paper is to dispel such attitudes and promote a wider use of light microscopy. Several examples are given which point out the indispensib1e nature of optical microscopy as a rapid means of defining and solving problems in mineral processing. The application of other instrumental techniques to augment the information obtained is also discussed, particularly the value of the combined use of the optical microscope and electron probe micro-analyzer.

Jan 1, 1981

El presente artículo describe la morfología, estratografía y geología de la mina de Cercapuquio. Su geografía consiste en una zona levantada por fenómenos orogenéticos, donde después de un período de glaciación regular y se ha formado en su parte central, la cabecera del río Chacuasmayo ( o Cerca puquio); en la parte oriental, un sistema de valles paralelos entre sí, con lagunas, tributarias del río La Virgen e igualmente, y en la parte occidental, otro sistema parecido de valles paralelos, lagunares, tributarios del río Canipaco.

Aug 1, 1955

By A. I. Urvanzev, N. V. Shikhov

"In this paper, we present the study’s results of electrical separation processes on the basis of new separator designs, new technological solutions, and newly discovered effects. We considered the options of enrichment by magnet separation of magnetite and titanomagnetite ores, ores and products containing chromium and manganese, ores of non-ferrous and precious metals. During pneumo-electric separation of mixed iron ore of SMPC, 43.3% of the output of the concentrate with an iron content of 61.7% was obtained in one step, with extraction of 70.5%. The paper also presents the results of the finalization on the air-electric separator of the magnetic fraction when separating oxidized ores of MPPOO (mining and processing plant of oxidized ores) on the Jans polygrade magnetic separator. A concentrate was obtained with an iron content of 65.1% with the extraction of 95.0% and tails with an iron content of 13.0%. The possibility of obtaining low-silica concentrates from these ores with an iron content of 67.15 and a quartz of 2.88% is shown. Also, the results of tests on the enrichment of chromite ores on the firing-magnetic scheme with corona-electrostatic separation are considered. On the initial ore of the Don MPP (mining and processing plant), a concentrate with a content of 61.8% Cr2O3 was obtained with a quartz content of ~ 1.0%. The results of pneumo-electric separation with triboelectric charge of the separated particles are presented. The results of the tests indicate a principal possibility of enriching chromite ores without costly high-temperature roasting. Dry technology of enrichment of manganese ores with the use of electrical separation increases the quality of the oxidized concentrate to the first grade and raises the total extraction by 2 times. For the Chineya deposit of titanomagnetite ores with copper impurities, electroseparation operations were carried out on two samples with a Cu content of 1.93 and 3.75%, respectively. For a sample with a Cu content of 6.02%, a copper concentrate output of 24.42% was obtained with a Cu content of 23.82% and the extraction of 94.88%. The results of enrichment by electroseparation of gold-containing sulfide ores can have the practical importance. For ores of the Berezovskoye deposit, a pyritic concentrate containing 100 g / t of gold was obtained after two or three operations of IES (integrated energy systems)."

Jan 1, 2018