Search Documents

By W. F. Hosford, E. W. Kelley

Deformation studies have been conducted at room temperature on single crystals of magnesium and magnesium alloys with thorium and with lithium. Single crystals oriented to suppress shear on the easily activated basal slip systems were deformed by plane-strain compression. Compression along the C axis was accommodated by {1011} banding. Compression perpendicular to the unconstrained c axis activated {1012} twinning, and, after virtually complete twinning, deformation continued by {1011) banding in the twinned material. Compression perpendicular to the constrained c axis was accommodated by the simultaneous operation of (1012) twinning against the constraint and (1011 ) banding. Although this orientation was favorable for {1010)(1210) prism and {1011}(1~10) pyramidal slip, these modes were not observed in pure magnesium or in Mg-0.5 pct Th. However, {10i0)(1~10) prism slip was observed in crystals of Mg-4 pct Li during compression perpendicular to the constrained c axis. Fracture in all materials occurred parallel to (1124) or {l~il) depending on the orientation and composition of the specimen. THE mechanical behavior of the hcp metals is strongly anisotropic. Although several slip systems have been reported the slip is cpmmonly in the directions of closest packing, the (1210),' and this does not produce strains parallel to the c axis. Hence the inherent anisotropy. The deformation mode most easily activated in magnesium at room temperature is (0001)(1210)- basal slip. Also {1010}(1~10) prism slip and {1011)(1210) pyramidal slip have been reported, primarily at elevated temperatures.2"4 However, at room temperature the shear stresses to activate the prism and pyramidal modes are roughly a hundredfold greater than that required for basal slip.'j4 Thus prism and pyramidal slip may be expected only under special conditions of loading. Strains normal to the basal plane can be produced by twinning, however. Many twinning modes have been reported for magnesium,' with (1012) twinning the most common and relatively easy to activate. Magnesium can deform by (1012) twinning when stressed along the c axis jn tension, but not in compression. In contrast, (1011) twinning is activated by compression along the c axis and not by tension. In addition to primary twinning, secondary twinning or slip can occur within the reoriented material of primary twins.' In general at least five independent shear systems must be active to bring about an arbitrary shape change such as that in the individual grains of a deforming polycrystalline material.' Because basal slip can_ provide only two independent shear systems and (1012) twinning can only accommodate an extension of the c axis, other deformation modes must be active in magnesium for an arbitrary shape change to occur. The purpose of this investigation has therefore been to study the various deformation modes in magnesium at room temperature, with special emphasis on those modes that are less easily activated. The effect of the alloying elements, thorium and lithium, has also been investigated. In polycrystalline aggregates, unambiguous identification of deformation modes is extremely difficult and the direct evaluation of the resolved shear stresses to activate them is not feasible. On the other hand, uni-axial tension and compression experiments on single crystals may not activate some of the- deformation modes because basal slip and/or {1012) twinning cannot be suppressed in most orientations. However, it should be possible to activate all possible deformation modes using oriented single crystals and plane-strain compression. Identification of active deformation systems and evaluation of the resolved shear stresses required to activate them should be facilitated. Wonsiewicz and Backofen have recently completed an investigation of the plasticity of pure magnesium crystals at various temperatures utilizing plane-strain compression and selected crystal orientations. This technique has also been used in the present work. The seven orientations selected for study are indicated in Table I. Plane-strain compression along the c axis (orientations A and B) should activate some deformation mode _other than basal, prism, or pyramidal slip, or (1012) twinning. In orientations C and D, prism or pyramidal slip would be expected to take place. When the compressive load is applied perpendicular to an unconstrained c axis (orientations E and F) the three slip modes should be suppressed but not (10i2) twinning. In orientation G, basal slip should occur.

Jan 1, 1969

By C. J. H. Brest van Kempen

The techniques developed should provide a useful tool, not only during the initial formulation of a suitable bolting plan for a new section, but also for periodic check¬ing on the utilization factor of hardware installed in the roof. Indications are that with present practice, utilization seldom exceeds 507.. Retro-fittable bolter equipment now available (FCBS?) allows doubling of the utilization factor in many cases. We are also introducing a computer pro¬gram based on the material outlined in this paper. This program can save a great deal of time in examining the real effect of implementing alternate bolting plans or using different installation techniques. It allows fine-tuning of bolt lengths, spacing and installation tension to mini¬mize roof support cost, while maximizing safe life of the mine opening. We have developed a procedure which allows easy, site-specific quantification of the need for reinforcement of a mine roof. The concept is based on the forma¬tion of a direct link between theory and empirical data to custom-fit each mine section. In its simplest form, the proce¬dure requires only recording of roof bolt torques in a sample working place (16 to 25 bolts) several times during the first week or so after initial bolting. The way in which the torque pattern changes during this time can reveal whether or not the bolts carry enough tension to maintain stability in that specific roof. From the same data, the nature of the anchorage horizon is derived. Specifically, shale or limestone can be distinguished from sandstone. If the procedure is repeated a few times (within the same mine section) with different bolt installation tensions, we can numerically characterize the roof in terms of one single value: an "effective angle of internal friction". This number can then serve to calculate trade-offs in bolting plan design, such as bolt length, bolt spacing and optimum bolt tension. Additional refinement is possible if a sagmeter is installed in the sample work¬ing place being monitored and if bolt anchorage capacity is determined. The lat¬ter can be done automatically on each bolt as it is being installed, using a system we developed and patented. Alternately, a number of pull tests could be performed. Using the sagmeter, bolt torque and anchor¬age data, it is possible to project the safe life of the supported opening. The details of the procedures described apply specifically to tensioned roof bolting, but a brief discussion paints the way for a similar analysis of full-column resin bolting also.

Jan 1, 1986

By Michael A. Linkous, Mark J. Zdunczyk

Silica in the form of sand and sandstone is one of the most common, and at the same time, unique industrial minerals. Found in every rock type of every geologic age and virtually everywhere in the world, silica is used in products that touch just about every aspect of daily life. Imagine a world in the 1990s without computer chips, fiber optics, or glass, and you have just begun to understand how important silica is to the quality of life we enjoy. The elements silicon (Si) and oxygen (0) comprise roughly 60% of the earth's lithosphere to a depth of about 16 km. The crystal structure of silicon dioxide consists of one atom of silicon bonded to four surrounding atoms of oxygen to form a three-dimensional network of SiO, tetrahedra. This network makes up the mineral quartz (Murphy and Henderson, 1983), the most common detrital mineral in most sandstones. Quartz is also a major constituent of many igneous and metamorphic rocks and is widespread as a siliceous cementing agent in various rock types. Although quartz is common, sandstones, quartzites, and pegmatites and the unconsolidated sediments derived from them that have a silica content high enough and pure enough to meet today's market demands for quality and consistency are not common. USES AND SPECIFICATIONS Silica sand that is mined and processed for industrial uses must conform to the chemical and physical specifications set by customers. In the United States almost half of the silica sand produced is used in the manufacture of glass. Other important products include foundry sand, ground silica, blasting sand, and fracturing sand. Glass Sand Silica is the principal glass-forming oxide in a glass batch. Glass manufacturers develop model specifications for each source of silica sand used. These specifications broadly define the limits and ranges for chemical and physical properties of the sand and are used by the manufacturer in calculating the desired batch mix or formula. Some specifications may be critical to a glassmaker and require very stringent limits on the quantity of impurities in the sand. For example, the total iron oxide content of a batch is extremely crucial when making white or flint glasses (Mills, 1983). Iron is present in almost every raw material used in a glass batch and must be carefully controlled in order to obtain a consistent color in the finished product. It is difficult, however, for a raw material supplier to tightly control the chemistry of a naturally occurring material such as silica sand. To a great extent the commercial quality of a sand is determined by its geologic history. Realizing this, glass producers tailor their model specifications to each source of approved material. In general, a glass company is concerned most about the consistency of raw materials on a day-to-day basis. Soda-lime-silica glass was the earliest type of manmade glass (Baker-Can, 1967) and still accounts for most of the glass manufactured for commercial use today (Mills, 1983). It is relatively easy to melt and shape and is less expensive per ton to produce than most other types of glass (Baker-Can, 1967). Soda-lime-silica glass is used in fabricating containers, flat glass products, incandescent and fluorescent lamps, glass fiber, and many other products. Heavy minerals such as ilmenite, leucoxene, kyanite, and zircon are impurities on which strict limits are placed for a glass batch. Because of their refractory nature they either do not melt or only partially melt, which results in stones or feathers in finished glass. Aluminosilicates such as kyanite also contribute unwanted alumina to the batch as they partially melt. Limits are especially rigid for refractory mineral grains coarser than 0.60 to 0.425 mm (30 to 40 mesh). [Tables 1 and 2] present typical specifications for silica sand used in flat glass and container glass products. The percentages shown represent an average of many companies7 specifications.

Jan 1, 1994

By J. H. Tu

The technical paper correctly points out that the kriging variance is not a good measure of the uncertainty of the estimated (i.e., kriged) value of individual blocks. The authors claim that their proposed jack-knife method, which is a rekriging of each block by eliminating, in turn, one sample from m the original sample set and then taking the average of the rekriged estimates, not only gives good block estimates, but the resulting jackknife kriging standard deviation is a useful indicator of the "true uncertainty associated with block estimates." However, they immediately abandon the idea of using the block-by-block standard deviations, reasoning that these standard deviations are not independent and that there is no easy way to utilize them. There may be another reason for not using them. The jackknife standard deviations for individual blocks given in their example are mostly in the range of 0.004 to 0.005 oz/st (0.14 to 0.17 g/t) with only one block having a high value of 0.012 oz/st (0.41 g/ t). These individual block standard deviations are as low as the jackknife standard deviation for the mean grade of the entire shape, i.e., 0.0041 oz/st (0.14 g/t). Do they represent the "true uncertainty" .of the individual block estimates? Could the authors explain this? In a global shape consisting of a large number of blocks, any given sample will affect the kriged estimate of only those few blocks within its vicinity. This is the rationale for the authors' selective rekriging, making the jackknife algorithm more efficient. On second thought, why not do away with jackknifing altogether? Just cumulate and normalize, if necessary, the kriging weights of each sample used during the ordinary block kriging process, and then compute the global variance from these kriging weights and their respective sample grades? After all, isn't the global mean grade nothing but the weighted average of the samples used in the estimation? Reply by G.S. Adisoma and M.G. Hester The jackknife is one of the many tools in a practitioner's toolbox to solve estimation problems. The strengths of the technique lies in its simplicity, i.e., it uses the concept of mean and standard deviation and the fact that it can be easily combined with other tools, in this case kriging. Because the jackknife kriging (JK) estimate is also the mean of the pseudovalues, the JK standard deviation is attractive just as the standard deviation of the mean explains the variability of the data. The difference is that the pseudovalue calculation in jackknife kriging uses the ordinary kriging (OK) weighting scheme instead of simple arithmetic averaging. The data used to illustrate the jackknife technique in the paper con¬sist of high values that are roughly three times the low values. The resulting JK estimate of the block grades show that the highest estimate is roughly twice the grade of the lowest estimate. The contrast between the low and the high estimate is more evident in the JK estimate than in the OK estimate, even though the mean grades of the blocks for the two estimates are very similar. Nonetheless, in this paper, we are concentrating more on the need for a more realistic measure of uncertainty, or precision, for the estimate. Unlike its OK counterpart, the JK standard deviation of the blocks clearly reflects the original data variation. The highest JK standard deviation of the blocks is three times its lowest value. This follows our intuition that, when the samples used to estimate a block is more variable, the resulting estimation variance (or standard deviation) should be higher than the case where the samples are more uniformly valued. However, block-by-block standard deviation or variance is of little practical value in reserve estimation and classification, as well as in mine planning. One is usually more interested in quantifying not the variance of the individual block estimate, but the uncertainties associated with a much larger dimension, such as the minable reserve. Thus, the thrust of the paper is to find a simple way to obtain a single estimation variance or standard deviation associated with the reserve grade estimate. The discussion by J.H. Tu did not mention how one would obtain the global variance from the OK weights and the sample grades. As a technique that offers a data value-based measure of uncertainty for its estimate, the "leave-one-out" jackknife fills this need nicely through the block kriging shortcut approach described in the paper. Note: The first column and the last two columns of Table 3 in the paper should have contained a single number each, namely, an OK estimate of 0.0317, a JK estimate of 0.0333 and a JK standard deviation of 0.0041 oz/st, respectively, for the shape, as are obvious from the text.

Jan 1, 1997

By Milton Glicken

THE airborne geophysicist is a busy man these days. In his plane he may have the airborne magnetometer, the airborne scintillation counter, and the airborne electromagnetic surveying system. Each of these is an independent tool, but all require additional auxiliary equipment for locating the aircraft in space: recording altimeters and Shoran or aerial cameras. Now there is still another piece of equipment, the airborne magnetic gradiometer, an accessory to the magnetometer. To understand its uses, consider the function of the magnetometer itself. Aside from detecting magnetic ore, the airborne magnetometer finds greatest use in spotting intrusions of igneous material. Where there is enough contrast in magnetic susceptibility of igneous rock and adjacent formations, it outlines the intrusion. Certain minerals also influence the magnetometer directly, but with the exception of magnetite and possibly one or two others, their effect is weak and can be detected only when there is sufficient ore and the magnetometer flight passes very close to it. An igneous intrusion of infinite depth with vertical sides is represented on a magnetometer record by an anomaly, as in Fig. 1. Amplitude of the high depends on susceptibility contrast of the igneous rock. Generally speaking, the edge of the intrusion lies below the point of inflection of the curve, and this point, where the curvature changes from positive to negative on the magnetometer profile, would be near A in Fig. 1, with a counterpart, of course, on the other side. Location of the contact is one of the principal objects of the survey, but finding the precise point is not always easy, as inspection of the curve near A will show. Mineralization is often found at the contact zones, as at B. Magnetic effects, if detected, may be small, as in B', and when superimposed on the anomaly due to the instrusion they are very difficult to discern and analyze. Furthermore, if these small fluctuations are to be perceived by the magnetometer the vertical scale should be large. This increases the slopes of the anomaly and makes detection of small deviations and inflection points even more difficult. The airborne magnetic gradiometer was designed to help overcome these difficulties. What it presents is the first derivative of the magnetometer record with respect to time, that is to say, the slope at any point. Fig. 2 represents an actual magnetometer record (solid line) with the corresponding gradiometer record (dashed line) superimposed. Both records read from right to left. Vertical lines on the original magnetometer record are automatic steps designed to keep the pen from going off scale. The slope of any curve is greatest at the point of inflection or point where the curvature changes sign, and this point is a maximum (or minimum) on the gradi- ometer. The chief advantage of the gradiometer is that maxima or minima are much easier to see and to locate precisely; hence an accurate location for the point of inflection can easily be found. Note that points C and D are more sharply defined than C and D'. Similarly the small fluctuations of the original record, so important to the interpreter, are far more clearly shown at E, F, and G, than on the original record at E', F', and G'. Though not necessarily highs and lows on the gradiometer, they do show up clearly what would take a painstaking analysis to detect on the original magnetometer record. Will the gradiometer have a particular configuration which indicates an orebody? Not necessarily. The total intensity curve, or original magnetometer record, can display an orebody in various ways, depending on dimensions, orientation, latitude, and composition, as well as on direction, flight height, and instrumental sensitivity of the traverse. Where the total intensity can take on so many different shapes the gradiometer must vary too. It is generally recognized that interpretation of total intensity magnetometer records requires an expert analysis; the gradiometer can be of considerable assistance to the expert but it does not replace him. Mechanism of the gradiometer is simple. A Leeds & Northrup recorder in the aircraft records the magnetic gradient simultaneously with the total intensity, which is on another recorder. Fiducial marks are put on both records simultaneously and the speed of the paper through the recorders is kept the same on both. This makes it possible to place one record over the other for direct comparison. In the laboratory the flights are positioned on a map. Maximum and minimum points on the gradiometer, which can then be posted on the map at their proper locations, may be expected to fall along a trend crossing the direction of flight. Trends should indicate the edge of an intrusion, or some other important features, and when superimposed on the total intensity contour map help greatly to locate the points of inflection, or line of zero curvature.

Jan 1, 1956

By E. W. Felegy

THE need for improved mine communication to increase efficiency and to insure greater safety has long been recognized. General and unrestricted communication between all points underground, and between the surface and all points underground, is probably the least advanced phase of the mining industry. An ideal system of mine communication must require no fixed wire installations. The equipment must be small, lightweight, and readily portable, and the power requirements low. A system that can be used not only under normal circumstances but also in an emergency, when the continuity of wires, tracks, and pipelines may be disrupted, must function independently of any aid furnished by standard installations. Radio communication offers possibilities of meeting all the requirements necessary for an ideal communication system in underground mines. Transmission of signals must be achieved through one or both of two mediums, through the air in mine openings or through the strata. The results or lack of results obtained by early investigators showed conclusively that radio communication by space transmission cannot be accomplished effectively beyond line-of-sight distances in underground passageways. A radio system underground therefore must depend solely upon transmission through soil and strata. The application of radio to underground mine communication was investigated by many individuals and agencies at different times in the last several decades, but little success was achieved before World war 11.2-0, The results of experiments during the war, and further knowledge gained in experiments with vastly improved communication methods and equipment after the war provided the background for additional research in radio communication in underground mines. During 1950 to 1.952 the University of Minnesota sponsored an investigation to determine the possibility of developing: a system of radio communication universally applicable in underground metal mines in the Lake Superior district. The possibility of using radio equipment to determine the imminence of rock bursts in deep copper mines in that district also was investigated. The investigation supplemented previous and concurrent emergency mine communication studies of the U. S. Bureau of Mines. Testing equipment and laboratory facilities maintained by the Bureau of Mines at Duluth, Minnesota, were used in the research program, which was conducted as a mining engineering graduate research problem by the present writer under the direction of T. L. Joseph and E. P. Pfleider. The radio units used in the research program were designed and built to specification solely to conduct tests of radio communication in mines. Two identical units were used in all tests. Each unit contained a transmitter section, a receiver section, and a power-supply section, mounted on a single chassis. The entire unit was enclosed in a single 10x12x18-in. metal case provided with a leather-strap handle for carrying purposes. The front of the case was hinged to open upward and provide easy access to the single control panel on which all controls were mounted. Storage batteries supplied the operating power for all tests. Standard 6-v automobile batteries were utilized to provide adequate capacity to conduct tests for a full day without exhausting the battery. A frequency range from 30 to 200 kc was covered in eight pre-fixed steps on each unit. The carrier frequencies were crystal-controlled and amplitude-modulated. The receiver employed an essentially standard superheterodyne circuit and was sufficiently sensitive to detect signal strengths of 5 micro v. A heterodyne circuit was employed in the transmitter to obtain the low-carrier frequencies used in the units. Power output of the transmitter, usually less than 2 w, rarely exceeded 3 w in any test. Tests were conducted in mines on the Vermillion iron range in Minnesota, the Gogebic iron range in Wisconsin, the Menominee and Marquette iron ranges in Michigan, and a copper mine in the upper Michigan peninsula. All tests were conducted when the mines were operating normally, and usual mining, maintenance, and transportation activities were in progress, so that any interference caused by normal production activities could be evaluated during the tests. Tests were made between different points underground in each mine, and between underground and surface points at some mines. Test readings obtained at any one mine were calibrated in the laboratory before another series of tests were begun at the next mine. The transmitter and receiver were separated by one or more levels in each test, and generally there was no other means of communication between test points. Two 100-ft lengths of rubber-covered wire were used for antenna wires on each unit in both transmission and reception. The ends of the wires were connected to ground points in one of several methods, depending upon physical conditions at each test site. The wires were clipped to metal rods about 200 ft apart in the back, side, or bottom of the mine opening where the character of the rock permitted driving rods. Both wires were clipped to points about

Jan 1, 1954

By Dell P. Williams, Howard G. Nelson

The tensile behavior of magnesium single crystals at a temperature of 26º ± 2ºC was investigated at varying pressure levels from 760 to 8 X 10-8 tow. For crystals deformed at a constant linear strain rate of 0.061 min-1. there was no apparent effect of the vacuum environment down to 10-8 torr. However, from a vacuum of 10-5 torr down to the lowest pressure attained (8 x 10-8 tor,), the effect of the vacuum environment was to increase the strain at the end of the first linear (or easy-glide) stage and to decrease the slope of this stage; the magnitude of this effect was found to be dependent on pressure. The slope of the second linear stage was also decreased at the lower pressure levels; however, this effect appears to be caused primarity by the vacuum effect on the first linear stage. The magnitude of the vacuum-environmrnt effect was also found to be dependent upon strain rate. The reduction in flow stress at 5 x 10-8 torr, as compared to the stress in air, was obserced to be about 10 pct for a strain rate of 0.0250 min-' and 70 pct for a strain rate of 0.67 min-1. No systematic effect of pressure on the critical resolvled shear stress was observed. The data interpreted in terms of a modified form of Mott's work-hardening mechanism for hexagonal metals. It has long been known that surface conditions influence the mechanical behavior of materials. Roscoe 1 demonstrated the importance of surface conditions on mechanical behavior by testing cadmium crystals with oxide layers. He found that the "apparent" critical resolved shear stress for cadmium was increased approximately 2.5 times by the presence of an oxide layer 1000 atoms thick. The magnitude of this effect was dependent on film thickness with crystals having films less than 20 atoms thick still showing a definite increase. This observed strengthening could not be attributed to any strength of the oxide film because of 1) the thinness of the films and 2) an observed increase in the flow stress as deformation proceeded. Harper and cottrel12 obtained similar results on zinc crystals which had been etched and steamed to give artificially thick oxide films. However, in the course of this study, they also carefully examined the very early stages of plastic flow for zinc crystals which in one case had been electrolytically polished and in the other had been lightly etched to produce a thin film. They then found that the critical resolved shear stress for both surface treatments of the crystals was actually identical but that the etched crystal exhibited a much more rapid initial hardening rate. This had not been noted previously. This result indicated that, in fact, the film caused an increase in the stress for continuation of slip, rather than for the initiation of slip. Lipsett and King3 investigated the effect of evaporated gold films on the plastic behavior of cadmium single crystals. For large angles (=75 deg) between the specimen axis and the normal to the slip plane, they found that the stress-strain curve of the coated specimen always lies above that for a clean specimen. The shear strain at the end of the first linear stage was greater in clean specimens than in coated specimens and the slope of the second linear stage was

Jan 1, 1965

By Robert E. Green

Experiments were performed in order to investigate the influence of magnitude of driving force, recouery, and previous heat treatment on grain boundary migration in deformed aluminum crystals. The frequency of occurrence of strain-free grains possessing Preferred crystallographic orientations was studied both as a function of heat treatment and as a function of amount of deformation of the matrix crystal. Aluminum of such composition as to exhibit precipitation-hardening behavior was used. CONSIDERABLE work has been devoted to the factors influencing grain boundary migration in metals.1'52 Aust and Rutterl-9 have studied grain boundary migration into matrix crystals containing a striation substructure, which provided a thermally stable driving force during the course of the migration experiments. These authors state that, while variations in the striation pattern were sometimes observed, it was possible to obtain reasonably uniform and reproducible striation structure by careful control of the solidification conditions. Admittedly, this source of driving force is a unique one and has served well in numerous experiments. However, although the striation substructure provides a thermally stable driving force, the subject of its reproducibility from crystal to crystal is questionable. In fact, Aust and Rutter3 attribute the scatter shown in some of their experimental points and several anomalies in boundary migration rates to variations in the substructure driving force along a single specimen. A further limitation on striation-induced driving force is that the driving force cannot be varied over wide ranges in a controlled manner. More often used as a source of driving force is the strain energy stored in a crystal during plastic deformation. This type of driving force has the disadvantage that it is not thermally stable due to recovery taking place simultaneously with the grain boundary mobility measurements. On the other hand, this strain-induced driving force is very reproducible from crystal to crystal since it is very easy to grow single crystals possessing the same purity and crystallographic orientation and then to strain them identically. In order to measure grain boundary migration rates two different methods are primarily used. Most often the technique employed is the heat-cool-etch method1' which involves thermal cycling, while the other technique, developed by Graham and Cahn11 using an X-ray diffractometer and goniometer furnace, involves continuous heating only. Thus the influence of thermal cycling vs continuous heating is a factor to be considered in grain boundary migration rate measurements, particularly in cases where the source of driving force is the strain energy stored in the deformed matrix, and recovery is likely to occur. Numerous recent investigations have shown that extremely small impurity additions to zone-refined metals exert a marked effect on grain boundary migration rates1-5, 9, 12-27 and a few have considered the effect of the distribution of impurities.28-35 The concentration of impurities and their distribution as influenced by heat treatment must also be taken into account in migration-rate studies. In the present article consideration is given to the influence of the magnitude of driving force, recovery, and previous heat treatment on grain boundary migration rates. In order to vary the driving force over a large range it was necessary to use as a source of driving force the energy stored in the matrix crystal during plastic deformation. A majority of the investigations were performed on aluminum specimens which were of such compositions as to exhibit precipitation-hardening behavior.

Jan 1, 1965

By S. D. Baumer, P. M. Hulme

IN the late thirties, the National Carbide Co. cooperated with C. E. Wood, of the U. S. Bureau of Mines, in his investigation of the relative merits of various desulphurizers, including soda ash, caustic soda, and calcium carbide. Laboratory tests showed that carbide, when it could be made to react, is an excellent desulphurizing agent for molten iron. Sulphur content can be driven to lower levels and higher extractions obtained with carbide than with actionsany of the more common reagents. Wood's results1 are shown in Table I. Unfortunately, as the Handbook of Cupola Operation puts it, the chemical fact that carbide is a good desulphurizer was of only academic interest because it was found to be extremely difficult to devise a practical means to make it react with molten iron. Calcium carbide is formed in the electric furnace at 4000°F and above, and its softening point is probably at least 500 °F above the usual working temperatures encountered in iron and steel practice. Consequently, carbide does not form a true slag but floats as a dry powder on top of the metal and only a very small portion of it ever comes in actual contact with the iron. Stirring with a rabble, or pouring the metal over the carbide, increases the efficiency only slightly. Extractions of 20 to 30 pct can be obtained in this manner, but conventional soda slag treatment can do better than this and do it more cheaply. All attempts to lower the melting point of carbide in order to obtain a reactive, liquid slag have so far proved fruitless. Directly under the arc in a metallurgical electric furnace, carbide becomes highly reactive. Excellent sulphur removal can be obtained without any slag other than a thin layer of carbide." imilarly, good results are obtained by adding small amounts of carbide to the finishing slag in double-slag arc furnace practice. To react a liquid with a solid, it is axiomatic that the liquid has to wet the solid before anything can happen. If the solid is heavier than the liquid, the problem is easy, but it becomes more difficult when the solid is much lighter than the liquid, as in the case of carbide and liquid iron. Wood recognized this problem and solved it in a unique fashion. The results shown in Table I were obtained by spinning the carbide beneath the surface of the molten iron by means of a refractory centrifuge. This technique allowed each particle of the finely divided carbide to come into intimate contact with the metal and to be wetted thereby. Wood's centrifuge technique was successful in the laboratory where it achieved excellent and consistent results. Some attempts were made to expand this method to commercial practice, but serious difficulty was encountered in obtaining a refractory centrifuge head that would be economically feasible. About this time the war intervened and the project lay dormant for several years. In 1944, it was revived. It was suggested that the carbide could be blown into the metal with a carrier gas in an attempt to eliminate the necessity for the expensive and brittle centrifuge. The idea was first tried out in a fairly large ladle of iron using natural gas as the carrier. Considerable sulphur was removed, but it was quite obvious that the use of natural gas was not practical. Attempts then were made to blow carbide into molten iron using, in turn, nitrogen, argon, carbon dioxide, air, and oxygen. The latter two gases proved unsatisfactory. Calcium evidently prefers oxygen to sulphur because in the tests calcium oxide and carbon dioxide were produced, the sulphur still being untouched in the iron. Nitrogen, argon, and carbon dioxide gave much better results, although the efficiencies and extractions were erratic, and only a few isolated tests approached the results obtained by Wood. Table II shows typical results obtained with these gases. The sulphur removals were interesting, sometimes even encouraging, but it is evident that such erratic behavior could not be tolerated in commercial practice. A number of different types of equipment, such as sand blasting machines, refractory guns, and the like can used to blow the solid into the metal. All types required relatively large quantities of gas in order to maintain the flow of solid carbide through the system and into the metal. It was observed that the bubbles of gas breaking through the surface of the metal contained quantities of unreacted carbide. The liquid metal never came in contact with these particles and if it cannot wet them it cannot react with them. The initial work had shown that carbide had great possibilities as a desulphurizer. In practice

Jan 1, 1952

By J. D. Hunt, D. T. J. Hurle

A uariety of eutectic structures are formed in faceted/nonfaceted eutectics. The various structures are explained in terms of the absence or presence of small facets in the liquid groove. Regular structures are produced when, for purely geometric reasons facels cannot form. The presence of a facet in the liquid groove leads to the formation of an irregular or a cell-like complex regular structure, due to the relative immobility of the groove. A classification of eutectics was proposed by Hunt and jackson, based on the presence or absence of facets on the primary phases (the absence of facets may be predicted from the dimensionless entropy of melting2). Eutectics were divided into three groups: 1) eutectics in which both phases grow in a nonfaceted manner; 2) eutectics in which one phase grows faceted, the other nonfaceted; 3) eutectics in which both phases grow faceted. It was suggested that regular1 rodlike or lamellar structures1 should be formed in the first group, that irregular or complex regular structures1 should be formed in the' second, and that irregular structures1 should be formed in the third. Recently it has been shown that the structural classification is incomplete. Regular rodlike structures (InSb-NiSb eutectic3), or broken lamellar structure (Bi-Zn eutectic, Fig. 8), are formed in alloys of the second group when the faceted phase has a large volume fraction. Hunt and jackson' argued that regular structures could form in faceted/nonfaceted systems, but that such structures would be unstable in the presence of microfacets on the lamella of the faceting phase, because the growth rate at a point on such a facet would depend on the kinetic undercooling at the point of nu-cleation on the facet, and not on the local kinetic undercooling. In these circumstances it would not be possible to consistently balance the compositional and kinetic undercooling over a lamellar structure and thus obtain a stable isothermal interface. In this paper we discuss in detail the origin of the various structures formed in faceted/nonfaceted systems, pointing out that the most important factor promoting the formation of a regular structure is the absence of a facet in the liquid groove. 1) FACET FORMATION IN SINGLE-PHASE MATERIALS Facets form when there is an energy barrier for the addition of a new solid layer on an existing solid. When a barrier is present,2 growth proceeds by the lateral movement of steps across a crystallographic plane. The rate-controlling stage of the process occurs when the step is first formed. Hulme and Mullin6 have shown that faceting in single-phase materials can only occur when both interface curvatures are convex with respect to the solid and when the surface is tangential to the facet plane. When even one of the curvatures is concave a facet does not form because new layers of solid from adjacent regions can always feed the facet plane, Fig. 1. Growth under these conditions is then as easy as elsewhere. Similar considerations will apply to eutectic growth; consequently the shape of the faceted phase is extremely important. 2) LAMELLAR SPACING CHANGES IN EUTECTICS Jackson and Hunt7 have shown that the interface undercooling AT of a growing lamellar interface (neglecting kinetic undercooling) is related to the lamellar spacing, A, and growth velocity, v, by an expression of the form: where m, Ql, and nL are constants of the system given in Ref. 7. Eq. [I] is plotted for fixed v in Fig. 2. Jackson and Hunt postulate that a regular eutectic grows near, but to the right of the minimum in the AT vs A curve. They argue that the spacing cannot be to the left of the minimum because the interface is then unstable to fluctuations in A. It cannot grow too far to the right, because when the spacing becomes too wide an isothermal interface can no longer be maintained over the large-volume-fraction phase.7 It is argued that during any change in growth rate the lamellar spacing remains in the permitted range by the movement of lamellar faults. When the spacing is too wide, the fault, shown in Fig. 3, moves to the left; when the spacing is too narrow it moves to the right. The faults, however, have to be formed. heir formation has been shown to occur when local regions deviate considerably from the spacing defined by the lamellar When the spacing is locally too narrow (it passes to the left of the minimum, Fig. 2), pinching off of the narrow phase occurs. When the spacing is locally too wide, the interface on the large volume-fraction phase can no longer be maintained as an iso-

Jan 1, 1969

By J. E. Dorn, S. K. Mitra

The low -temperature tensile and creep behaviors of single crystals of copper were evaluated and analyzed in such a manner as to provide an estimate of the separate contributions of short-and long-range stress fields to strain-hardening. Furthermore, the average force-displacement diagram for thermally activated intep-section of two dislocations was estublished. This diagram plus a knowledge of the variation of dislocation spacing and the long-range back stresses with strain permits on accurate prediction of creep rates. The calculated activation energy for intersection under conditions of a constant strain rate increases linearly with the absolute tempevatus-e as required by theory. AN understanding of the detailed mechanisms for strain hardening constitutes one of the principal unsolved problems in dislocation theory. Two major models for strain hardening have been advanced in the past. The one that has received greatest attention assumes that strain hardening arises exclusively from long range interaction stresses between moving dislocations and piled-up arrays of blocked dislocations on the slip planes. This type of interaction was first announced by Taylor' who revealed that the back stress fields due to a simple uniform array of positive and negative dislocations entrapped in the deformed crystal would result in parabolic hardening. Shortly thereafter Andrade and Henderson" demonstrated that the strain hardening of fcc single crystals was not parabolic, as previously thought, and finally it was recognized that a typical stress-strain curve consisted of three successive stages of deformation, niz., the easy glide, Stage I, linear hardening, Stage 11, and the parabolic hardening, Stage 111, ranges. The objections to Taylor's somewhat na'ive model, which were presented so forcefully by cottrell; were largely removed by the more realistic details incorporated in Mott's analysis.5 But because Mott's theory for hardening via long range stress fields gave somewhat analogous results to that of Taylor's (inasmuch as it also predicted a parabolic rate of strain hardening whereas the observed rate of strain hardening in Stages I and I1 were linear), it was not widely accepted. Major consideration was therefore given to models, such as those which were advanced by Friedel and seegere that were formulated for the ad hoc purpose of yielding linear rates of strain hardening. The second major thought regarding strain hardening is based on the concept that it arises principally from short-range stress fields due to the interactions between intersecting dislocations. Cottrell and stokes7 showed, several years ago, that the constancy of the flow stress ratio at two temperatures regardless of the strain was inconsistent with the concept that strain hardening arose exclusively from long-range back stresses. The argument that strain hardening was primarily due to local interactions of intersecting dislocations was presented in considerable detail by asinski.' Extending Basinski's method of analysis of the intersection process, Mitra, Os-borne, and dorn recently demonstrated that indeed the strain hardening in aluminum single crystals arises principally from local effects coincident with intersection; however, these conclusions, too, must be modified, as will be shown later in this report. The present investigation, devoted principally to the low-temperature deformation of copper single crystals, was initiated in an attempt to ascertain whether or not the same conclusions arrived at for aluminum also apply to metals, such as copper, which have much wider stacking faults. It was soon observed that the strain hardening in copper could not be attributed exclusively to local effects between intersecting dislocations. Previously no analytical method for arriving at the possible simultaneous contributions of long-range stress fields and localized forces on intersecting dislocations was available; consequently, the separation of these two factors could not be readily accomplished. In the present report a method of estimating the separate contributions of each of these two factors to strain-hardening will be presented. The authors will show that both long-range stress fields of the type contemplated by Seeger and Friedel as well as short-range forces of the type considered by Basinski are responsible for strain hardening in fcc metals at low temperatures. This method of analysis also accounts for, in a satisfactory way, the effect of stress, temperature, and strain on the creep rate under constant stress. Furthermore, in the course of presenting their methods of analysis the authors will also reveal the rather complete agreement of their experimental data with the concepts of the theory for thermally activated intersection of dislocations. INTERSECTION MODEL As shown by seegerl0 the strain rate arising from thermally activated intersection of dislocations is given by

Jan 1, 1962

By Keith E. Dyas, John Nelson, Ronald T. Johnson

GENERAL DESCRIPTION The Bruce mine of Cyprus Mines Corp. is located in Bagdad, AZ. The mining method used is open cut-and-fill. Of the annual production of 81 647 t (90,000 st), approximately 83% is taken from load-haul-dump (LHD) stopes and the balance from slusher stopes. All ore is produced from the area between the 1250 level and the 2300 level. The average travel time from the shaft pocket to the stope is approximately 5 min. GENERAL ORE BODY REQUIREMENTS AND LIMITATIONS Size, Shape, and Dip The Bruce ore body occurs in quartz-sericite schist with Dick rhyolite on the footwall and andesite on the hanging wall. Diabase dikes are found in the hanging wall; there is also a dike coming off the footwall and crosscutting the ore body. All of the rock types are of the Precambrian Yavapai series and have been subjected to regional metamorphism. A composite of the ore body is given in Fig. 1. The deposit is of massive sulfides occurring as a steeply dipping replacement body. On the upper levels the ore is veinlike with widths from 0.6 to 4.6 m (2 to 15 ft), dipping at 1.4 to 1.5 rad (80° to 85°). On the lower levels the ore is dipping from I to 1.2 rad (60° to 70°) with widths from 3 to 16.8 m (10 to 55 ft). The strike length varies between 107 to 183 m (350 to 600 ft). The rhyolite footwall generally has a knife-edge contact with the massive sulfides. The exceptions to this are the upper levels where there is a 1.5 to 3 m (5 to 10 ft) band of silicified sericite schist between the sulfides and the rhyolite. In the southern part of the ore body the hanging wall is tuffaceous andesite and andesite. In this area the contact is generally sharp and easy to follow. However, to the north there is a large chlorite schist zone that crosscuts the bedding and comes in contact with the massive sulfides. This is apparently due to hydrothermal alteration of the andesite. The chlorite schist is highly mineralized with chalcopyrite and pyrite and quite often forms economic pockets of ore. In the massive sulfides the chief ore minerals are sphalerite and chalcopyrite. Pyrite is the predominant sulfide with considerable pyrrhotite throughout. Bright arsenopyrite ouhedrons in fine grain massive sulfides are quite common. Occasionally small amounts of galena are seen, usually near the foot or hanging wall contacts. On rare occasions tennanite is associated with massive arsenopyrite. Minor amounts of quartz, calcite, and un¬replaced remnants of sericite schist occur, but essentially pyrite is the gangue in which the ore minerals occur. The ore values are in excess of 3.5% copper and 12.5% zinc with some silver and rare gold as byproducts. Ground Conditions The massive sulfides are generally self-supporting. One exception is in the 1850 stope where the ore body is 9 to 11 m (30 to 55 ft) wide and 152 m (500 ft) long. There are flat to shallow dipping slips and seams in the ore, creating extremely blocky ground. For support, old 25.4-mm (1-in.) hoist ropes were installed tensioned to 27 t (30 st), and then cement grouted over the entire length in longholes [14 to 15 in (40 to 50 ft) in length) drilled on 3-m (10-ft) centers from the level above. This has tied the formation together very successfully and virtually eliminated the blocky ground condition. Both the hanging wall and footwall are quite shaley in some areas. Reasons for Adopting Trackless Open Cut-and-Fill Methods First, any method other than open cut-and-fill would have caused too much dilution. The use of rubber-tired mining equipment in the pro¬duction stopes requires a footwall ramp. The inclines in ore will be mined out, so this ramp in the footwall will provide access to and from the stopes (Fig. 2). This incline is very expensive, but necessary to convert existing stopes to LHD mining. 'The final cost of ore mined by the LHD machines has not been determined. As of 1972, tons per manshift in the 2150 stope-the only one to complete a full cut-had increased from 7.58 t (8.36 st) to 12.83 t (14.14

Jan 1, 1982

By G. Lucas

"Material substitution occurs continuously in response to competitive and economic pressures. Technical development can accelerate or slow substitution by improving the performance of the invading or defending material. The choices are seldom simple and have to be made in the context of continuous commercial change.The development and commercialization of a new aluminum material is examined. The material has been introduced into· several different markets, so it is possible to compare and contrast the degree of success obtained in each.IntroductionAluminum-based materials have been in use for over one hundred years and , therefore, the development of a new family of alloys is rare. In the early 1970s, Dr. L.R. Morris and his coworkers at Alcan' s Kingston Research Centre started work on what was, at the time, something of a scientific curiosity-a family of alloys strengthened by an unusual mechanism.This paper deals with the development and commercialization of what became known as the Alcan 255 alloys"". These alloys have found uses in several markets, usually as improved substitutes for existing materials. Forecasting the usefulness of a substitute material in an existing marketplace is difficult, in part, because even material users are seldom able to specify precisely their requirements. This uncertainty can cause the failure of some substitutions but can also lead to opportunities which were not initially obvious.Technical BackgroundPure aluminum is a soft, weak material. It can be strengthened by the addition of various alloying elements and by work hardening. Alloying elements usually act by forming solid solutions which are stronger than the pure metal or by precipitating during heat treating or aging and so preventing the easy movement of dislocations during deformation. Elements which can perform either role had been investigated for decades and were thought to offer little chance of technical breakthrough in 1970. An outgrowth of the then new and exciting research on directional solidification seemed, however, to offer such promise.Some aluminum-iran-manganese alloys will solidify under certain conditions as 'coupled growth' eutectics (Figs. I and 2). The microstructure shows one phase growing as long rods through the other. This is an uncommon structure and it was investigated to see if it had equally unusual properties. On deformation by rolling the rods were broken up into small equiaxed , evenly-spaced particles (Fig. 3). Materials with this structure were found to be stronger than other alloys with similar amounts of alloying addition, and to resist thermal softening remarkably well. This combination of properties was thought initially to be due directly to the particles by a dispersion strengthening mechanism, but later this was found not to be strictly true."

Jan 1, 1987

By Lindsay Norman

To many who for years have scrutinized the US mineral supply picture, recent, often strident debate on present-day security of many critical mineral supplies echoes sentiments repeatedly expressed in the past decade by the minerals industry. At no time since the last world war has such a flurry of public concern been expressed for the economy's mineral sector. Where once mineral availability problems were relegated to the newspaper's business section or not reported at all, today comprehensive analyses of our international mineral posture are discussed in detail by some of the nation's most respected and widely read periodicals. In past years, disinterest was also experienced whenever the mining industry attempted to carry its message to Congress, the public, and the government's executive branch. Among minerals professionals, the past decade was a time of particular frustration clue to serious erosion ill US ability to competitively produce the vast array of raw materials vital to the economy acid national defense. Fervent calls for immediate attention were simply not answered. These professionals have understood that mining and agriculture are the primary sources of wealth, fulfilling virtually all needs and creating and sustaining jobs. Why then has it been so difficult to raise the consciousness of the American public, and even more surprisingly, of the government and national leadership? The answer to this question is perhaps endemic to how government functions, but pore important, it begs that mining professionals capitalize on the opportunity and the attention now at hand. Carefully conceived and implemented actions by both private and public sectors are needed more than ever before in the past 35 years. To this end, it is vitally important to seek out and resolve the root causes of supply problems and not dwell on superficial solutions. The following discussion attempts to establish a simple framework to view this process. It does not presume to be an exposition of cause and effect, but hopefully identifies some needed steps. Growing Awareness in the 1970s Of all events stimulating current concern, certainly the OPEC oil embargo has left the deepest impression. It was inevitable that after such a shock, man. Americans would begin asking whether the US was as vulnerable to cutoffs of minerals as it was to oil cutoffs. Then, when serious trade security questions surfaced in sonic mineral-rich nations in Africa and the Persian Gulf, the ominous term ''resource war" began to be heard. Countries such as South Africa, Zaire, Zambia, and Zimbabwe have suddenly become key areas for testing our national security resolve. As the US witnesses the influx of Marxist influence in many sub-Saharan exporting nations and the rising threat to free world access to critical materials and energy, the assurance of adequate supplies is becoming a national issue at last. The US is now learning that self-sufficiency for many vitally important mineral commodities has vanished. Of course, it did not vanish overnight; it had been leaking away for years, and the trend was noted by industry and a few in government. Within the minerals community, suspected weaknesses in America's resource posture were sought and found. As a result, the country's heavy reliance on foreign sources fur more than a score of minerals, many extremely vital to security, has been forcefully documented and the case for drastically altering the supply unbalance hits been proposed. The renewed concern for national defense is central to almost all proposals for minimizing US foreign mineral dependence. It is not surprising that many of the voices heard today on the dependency issue are active members or alumni of the militate establishment. Unfortunately, their almost total focus on the security aspects of dependency has tended to obscure important underlying issues which are not directly defense-related. Some of the proposals advanced might mitigate the deeps-dency problems, but they still fall short of curing the underlying problems that have led to a steady loss in mineral self-sufficiency. In almost all instances these problems call be traced to increasing government influence on the free market minerals economy. Some national security proponents seek to attain total self-sufficiency in minerals. Such arguments must he tempered by existing realities. It is easy to demonstrate that the US obtains substantial quantities of sonic essential minerals from potentially insecure sources abroad. That the US will continue to do so in the foreseeable future is not in doubt Uncertainty begins, however, when we try to interpret the significance of these facts. It is important to understand that mineral dependency does not irrevocably lead to vulnerability. Unlike oil, no mineral commodity combines the same degree of universal indispensibility and centralized foreign control of supplies. Moreover, although many US-required minerals are produced by fewer countries than export oil, those minerals cannot approach petroleum in economic or industrial importance. Finally, most foreign supplies come front friendly, secure nations such as Canada, 'Mexico, and Brazil. This, aid more, constitutes a vital element in US economic health as a world trading nation. The Cost of Interruption The US is currently stronger and more resilient than many expected after absorbing the oil embargo shock and subsequent price increases. Nevertheless, major worldwide

Jan 6, 1981

By John W. Wagner, Robert K. Willardson

Single crystals of Pbl-xSnxTe have been grown from nonstoichiometric, cation-rich melts with the objective of producing as-grown, bulk material containing carrier concentrations ranging from 1016 per cu cm to 1018 per cu cm. Three specific crystal composi-tions were investigated in detail; x = 0.00, 0.10, and 0.17. Pull rates of from I to 3 mm per hr were used. Single crystals were successfully pulled from melts containing as little as 30 at. pct Te. Hall coefficients, resistivities, and carrier mobilities of these materials were determined. The relationship between the composition of the melt and the carrier concentration in the as-grown crystal has been studied for the three crystal compositions of interest. BULK single crystals of Pb,-,Sn,Te have previously been grown from stoichiometric melts.1,2 Such crystals are p-type and have relatively high carrier concentrations ranging from -9 x 1018 per cu cm for PbTe to -8 x l020 per cu cm for SnTe at 77°K. These carrier concentrations result from deviations from stoichiometry (lead vacancies) in the as-grown crystals. Since lower carrier concentrations are desirable for electrooptic device applications, these crystals are usually subjected to long-term, isothermal anneals.' This paper reports on the growth of Pbl-xSnxTe single crystals from nonstoichiometric melts with the primary objective of producing as-grown material containing relatively low (1016 to 1018 per cu cm) carrier concentrations and also reports on the general characteristics of these crystals. The phase relationships in the Pbl-xSnxTe systems are such that materials solidifying from nonstoichiometric, cation-rich melts will have smaller deviations from stoichiometry than materials grown from stoichiometric melts. Fig. 1 is the T-x phase diagram for PbTe in the vicinity of the stoichiometric composition.3 A crystal grown from a stoichiometric melt will solidify at a melting point maximum at which the solid will contain -0.5002 atom fraction of tellurium. PbTe single crystals grown in our laboratories from stoichiometric melts have carrier concentrations of 9 x 10" per cu cm, indicating that the excess tellurium in the crystals is as expected from this phase diagram. However, growth of PbTe from a lead-rich melt will result in material having a more nearly stoichiometric composition. Although the addition of Sn to the melt shifts the solidus curve further toward the tellurium-rich side,4 the general discussion given for PbTe applies to the Pbl-xSnxTe systems as well. EXPERIMENTAL Single crystals of Pb1-xSnxTe have been grown in our laboratories from nonstoichiometric, cation-rich melts using the Czochralski technique and boric oxide liquid encapsulation. The details of the growth apparatus and growth technique have been reported in a previous paper on growth of these alloys from stoichiometric melts.2 In the present study, three specific crystal compositions were investigated in detail; x = 0.00, 0.10, and 0.17. Growth of alloy crystals from nonstoichiometric melts requires considerable care, and good quality single crystals were obtained in this study only by optimizing the mechanical and thermal stability of the growth system and by using pull rates of from 1 to 3 mm per hr (Pbl-xSnxTe crystals are easily pulled from stoichiometric melts at rates of from 5 to 10 mm per hr). The liquid encapsulation technique was found to yield near-ideal conditions, since the B2O3 layer increased the thermal stability at the growth interface, permitted easy attainment of near-ideal thermal gradients, and dampened vibrations at the melt surface. The hygroscopic character of the B2O3 was a slight problem and vacuum heat treating was necessary to completely remove the water from the boric oxide. During initial growth, the seed diameter was reduced and a narrow neck (1 to 2 mm diam) of several millimeters length was grown. The latter steps were found to be necessary for the growth of single crystals, i.e., if either of these two requirements were

Jan 1, 1970

By M. L. White, J. L. Shafer, C. L. Caenepeel

Often an in situ leach is the only practical economic method for copper recovery from small low grade oxide deposits. The decision to develop a copper property by an in situ blast and leach is strongly dependent on ore grade, tonnage, hydrology, and the copper extraction and acid consumption rates. The inherent leachability of the ore will in part determine the desired amount of fracturing of the ore deposit by the blast in order to obtain a copper extraction rate that is economical. For the last several years Occidental Research Corp. (ORC), has undertaken a modest effort to address the question of how to best identify and determine the information necessary to predict and control the operation of an in situ leach for the economic recovery of copper.

Jan 2, 1979

By Paul A. Taylor

MUCH information concerning pegmatites which was thought to be true a few years ago has been proved false, and what is now actually known about some pegmatites is not true of many others. The erratic and seemingly unpredictable structure and variable composition of this class of mineral deposits has been widely emphasized. Even parts of the same pegmatite body exhibit marked differences in texture, mineral composition, width, and attitude. Constructive geological thinking in respect to pegmatites now aims to establish general laws rather than to stress the confusing diversity of features having no special economic significance. Substantial progress has been made in classifying different types of these deposits according to general features, internal structure, mineralogy, and origin. In some cases it has even been possible to block out tonnage reserves in advance of mining. It is still easy, however, to make highly erroneous predictions after a preliminary examination of a pegmatite prospect. Pegmatites are important to the economic well being of the country and to its military security. They furnish virtually all the feldspar, strategic mica, beryl, columbium, tantalum, and caesium utilized in the United States, as well as sundry other minerals and significant amounts of lithium and rare earth minerals and gems. With the exception of vermiculite, occasional ilmenite-rutile, and perhaps soda-lime feldspar and garnet deposits, basic pegmatites are of little economic importance. Consequently in this paper, as in common parlance, the term pegmatite generally relates to coarsegrained acidic rocks or what is aptly called giant granite. Available data indicating the size and importance of the production and trade in specified pegmatite minerals are summarized in Table I. Geological Features Much of the latest thinking on the economic geology of pegmatites is now available in a 115-page monograph' by a group of experts who participated with geologists of the Federal Geological Survey in the widespread wartime investigations. Doubtless the most significant feature of the monograph is indicated by the title, The Internal Structure of Pegmatites, but it also contains a vast amount of other new information and includes the assimilated concepts of many earlier writers, whose works are given in a comprehensive list of references. The shape, size, attitude, and continuity of many pegmatite bodies is controlled by the structure of the older rocks in which they occur. If the older rocks are easily penetrated, e.g., biotite schist, most of the pegmatites in a given district will be found outside the parent granite mass as exterior pegmatites. Marginal pegmatites are more prevalent if the older rocks are massive, unsheared, and sparingly jointed. Networks of pegmatites are abundant in highly-jointed rocks. In strongly foliated schists the bodies are usually lenticular, whereas in highly-folded areas they assume tear drop, pipe or pod-like, bow-shaped, or sinuous forms. Jahns2 recognizes five major shape classes: l—dikes, sills, pipes, and elongate pods; 2— dikes, sills, pipes, and pods with bends, protuberances, or other irregularities; 3-—trough-or scoop-shaped bodies with or without complicating branches; 4—bodies with the form of an inverted trough or scoop; and 5—other bodies, including combinations of the above and miscellaneous shapes. Many pegmatite deposits are scarcely big enough to be recognizable as such. Most of them, in fact, are small tabular deposits less than 4 in. wide and usually without economic concentrations of minerals. On the other hand, some pegmatites are more than a mile long and over 500 ft wide. The ratios of length to breadth range from 1 : 1 to 1 : 100. Although the vertical dimension bears no invariable relationship to strike length, tabular deposits or large lenses are often symmetrical enough to show nearly as much continuity down dip as in their horizontal extension, and some pipes or pods are amazingly persistent in the vertical plane. Small pegmatites often string along a fairly definite trend line; in a given district major bodies may lie roughly parallel, and where only a few of them do not, the erratically disposed bodies generally differ in composition from those conforming to the regular pattern. This does not apply, however, in all districts. Characteristically, pegmatite veins pinch and swell or split into branches. When they pinch out entirely it is often possible to find a new body by prospecting the extension of the strike or dip, but the chances of finding a hidden deposit are ordinarily too uncertain to justify much subsurface prospecting. Diamond drilling may yield valuable information as to the continuity of known deposits whose upper portions are well-exposed. Some deposits, in fact, can be proved up for hundreds of feet by surface trenching and then intersected by drill holes at various depths like any other vein-like deposit. Others twist and branch, apparently defying all efforts to explore them short of actual mining.

Jan 1, 1954

By B. S. Crocker

Pebble grinding was used at Lake Shore Mines in 1949. A full description of experimental evidence and test plant results was published in 1952 1 and further operating details in 1954 2.' In more recent years the term autogenous grinding has been coined and is now frequently seen in the technical literature. Autogenous crushing and/or grinding covers any grinding mill in which the larger pieces of ore are made to grind the fine pieces; the crushing and grinding may be either dry or wet. This discussion deals only with wet autogenous grinding, and only in the fine grinding part of the circuit, i.e., from 6 mesh to 92 pct —325 mesh. The term pebble milling could apply to fine autogenous grinding in which the pebbles are made from the ore itself, or it could also refer to grinding with pebbles, such as flint pebbles, from a source outside the mine. The first mill to use screened ore to grind the ore (1949) was Lake Shore Mines, Kirkland Lake, Ont. Pebbles were screened from the jaw crusher discharge and used in 5x16-ft tube mills which had been converted to 6 ft 8 in. by 16-ft grate discharge pebble mills. The same general practice was adopted the following year by the Wright-Har-greaves Mine in Kirkland Lake. Shortly after that the Neptune Mines in Nicaragua started correspondence with the writer concerning the possibility of using screened ore for grinding in their plant. They first ran some plant-scale tests which confirmed the Lake Shore findings, with the ultimate result that their plant was successfully converted in 1956 to an autogenous grinding plant. In 1957-1958 the writer was successful in converting the grinding plant of Renabie Mines in northern Ontario to autogenous grinding. In all these plants the existing grinding equipment was converted, usually by expanding the diameter of the shell to make the change from steel grinding to ore pebble grinding mills. In all the above plants primary grinding was done in either small rod mills or ball mills. These mills first reduced the pebble mill feed to about 6 mesh. The final grinding in the pebble mills varied from 75 pct —200 mesh to 92 pct —325 mesh. At Lake Shore three stages of pebble milling were used, with a different size pebble in each stage. In other parts of the world interest was being shown in this form of grinding, and in March 1952 the writer had some correspondence with the mill staff at Outokumpu in Finland, with regard to the pebble system used at Lake Shore. At Stockholm in 1957 the account of the crushing and grinding system at Outokumpu was presented in a paper by H. Tanner and T. Heikkinen.V his is the only ore grinding plant that does not use grate discharges on its pebble mills; trunnion discharges equipped with heavy reverse spirals retain the pebble load. The first new mill designed to use screened ore as a grinding medium was the Bicroft mill at Bancroft, Ont., which began operation in the fall of 1956. In 1957 this plant was followed by similar installations at Faraday Mines, also in the Bancroft area, and the North Rankin Nickel Mines in the North West Territories. In 1958 the Dyno Mill at Bancroft was converted, using the same type of grinding. Since all these plants, designed by Kilborn Engineering (1954) Ltd., were originally planned as pebble grinding mills, they were able to take full advantage of the latest design and technique. They are neat in appearance and very efficient and easy to operate. Effect of Ore Hardness: It is often commented that this type of autogenous grinding applies only to hard siliceous ores. Experience has shown that this is not so. In the past ten years the author has had an opportunity to test more than a dozen ores, several of which were quite soft. One of these was shale. The softer ores actually make better looking pebbles than the hard ores. These soft ores produced no particles in the intermediate size range which could not be ground by the largest pebbles in the mill charge. Slabby ores, such as shales, make a suitable pebble for the —6 mesh grinding. It is not generally recognized that for fine grinding a spherical medium is not essential or more efficient. Another frequent objection to pebble grinding is the belief held by some operators that there is too much variation in the hardness of their particular ore to make it acceptable as a source of pebble media. Experience has also shown that this is not a serious problem at all. The variation in pebble load due to changes in the ore hardness is nothing like as great as most people would expect, and the method used for feeding the ore and controlling the the load in the mills is more than sufficient to take care of daily variations in ore hardness. This point

Jan 1, 1960

By George S. Ansell, John B. Hudson, Stephen A. Koffler

The permeability of hydrogen through the a phase of palladium has been measured by a low pressure permeation technique under conditions such that bulk diffusion was the rate-controlling process. The observed permeability is described by the equation: J = 1.80 x 1O-3 P½exp(-3745)/RT) cc(stp)/sec/cm2/en over a range of hydrogen pressure, P, from 2.9 x 10-5 m Hg to 5.0 x 10-3 cm Hg, and over a temperature range, T, from 300" to 709°K. The fact that the permeability shows a square root dependence on pressure and a reciprocal dependence on thickness was taken as evidence that bulk diffusion, rather than surface reactions, was the rate-controlling process. The permeability data were used in conjunction with the solubility data of Salmon et al., to determine the diffusivity of hydrogen through palludium as: D = 4.94 x 10-3 exp(-5745/RT) cm2/sec There was no influence of sub structural defects observed over the temperature range employed. From the permeability data obtained, coupled with grain size measurements, it was concluded that the ratio of grain boundary diffusivity to bulk diffusivity was less than 105 over the range of temperature investigated. THE diffusive mass transport of hydrogen in the a phase of palladium has been studied previously by numerous investigators.' In spite of the large amount of attention this system has received, there is not good agreement between the results obtained in different investigations.' This is due in part to the fact that the mass transport was surface-limited during some of these studies, rather than being diffusion-controlled3-5 The reason for the disagreement in other cases is not clear. These studies made use of such techniques as rate of absorption from solutions6 and gases,' electrochemical potential,8 time lag,' and permeation10,11 to determine the mass transport behavior. Of these, the gas permeability technique is the only method which allows an easy test to determine if diffusion is the rate-controlling mechanism, thus eliminating the uncertainty regarding the limiting transport processes inherent in the other techniques. The two most recent permeability studies are those of Toda10 and Davis." Toda determined the permeability of hydrogen in the a phase of palladium over the temperature range from 170" to 290°C, and over the pressure range from 36 to 630 mm Hg utilizing a steady-state gas-permeability technique. Toda's result was: J = 1.41 x 10-3 P½ exp(-3220/RT) where J = specific permeability in cc(stp)/sec/cm2/cm, P½ = square root of the inlet pressure in (cm Hg)½, R = Universal gas constant, and T = temperature in deg Kelvin. Davis11 also employed a steady-state gas-permeability technique over the temperature range from 200" to 700°C and over the pressure range from 0.02 to 760 mm Hg. His result for the permeability of hydrogen in the a phase of palladium was: J = 3.15 x 10-3 P½ exp(-A440/RT) In the range of overlapping temperature for these two investigations, the values of the specific permeability calculated from the above two equations differ by a factor of about 1.8. In the present investigation, the permeation of hydrogen in the a phase of palladium was determined over a wide temperature range, 27" to 436oC, and over the pressure range from 2.9 x 10-5 to 5.0 x 10-3 cm Hg. This temperature range overlaps that of the previous investigations of Toda and Davis, but also covers the lower temperature range which has never before been investigated. The lower pressure range used here avoided the interaction between the dissolved hydrogen atoms observed at higher hydrogen concentrations.' MATERIALS The as-received palladium specimens were cold rolled from a casting and were supplied as 5.08 cm discs of 0.508 and 0.762 mm thickness. According to J. Bishop and Company specifications, the composition of the discs was 99.95 pct Pd, the balance being Cu, Ag, Au, and Ir. In order to obtain samples of varying grain size, the as-received discs were then heat treated. Sample 1 was treated for eight minutes in a nitrogen atmosphere at 810°C and then air-cooled. Sample D was heated first to 550°C in helium. The helium atmosphere was then immediately replaced by hydrogen and the temperature was slowly raised to 1220°C and held for 22 hr. The sample was then cooled to 550°C where the hydrogen was replaced by helium and the disc was further furnace-cooled to room temperature. Sample H was given the same heat treatment, only with hydrogen substituted for helium below 550°C. The reason that hydrogen was not used throughout the entire annealing cycle for samples D and H was to prevent the distortion encountered by low-temperature cycling in hydrogen observed by Darling." After these heat treatments were completed, the

Jan 1, 1970

By Niles E. Grosvenor

One of the most important considerations in the efficient operation of an under¬ground mine is the haulage system. Often the determining factor between profit or loss is the quick removal of ore and waste from the working places to secondary and main-line haulage areas, and so on to the outside. Important, too, is moving supplies from the surface to the working faces so that the loading process can continue with little interruption. Men must he transported in a rapid but safe manner. It has been through the efficient use and generally the combination of mine cars, track, belt conveyors and rubber-tired haulage equipment that underground operations have been able to compete with the more popular strip or surface mining. As near-surface ore bodies are exhausted, underground haulage will play an expanding part in economically furnishing the world's needs for all types of minerals. The choice of underground haulage equipment, wherever possible, should be one that will give the smallest overall cost of ore removal during the life of the mine while meeting necessary safety requirements. The reader is referred to Sec. 12 for equipment such as scrapers and load-dump-¬haul units that perform loading as well as haulage duties. 14.1-MINE CARS AND TRACK NILES E. GROSVENOR Main-Line and Secondary Haulage-Many mines today use a combination of belt and rail haulage. Even if a- belt system is used to carry the product from the face to the surface, track is used to transport workmen and supplies. A track system, when properly installed, will provide interruption-free and safe haulage. Schrecengost 2 lists the following as major advantages of track haulage: 1. Safety in transporting men in and out of the mine in personnel cars. 2. Easy and rapid transportation of supervisory personnel. 3. A temporary shutdown occasioned by a roof fall or power failure along the haulage system will not shut down the production areas. 4. Quick availability of repair parts and supplies. 5. Large pieces of coal or rock can be handled without damage to the haulage equipment. 6. In areas where quality fluctuates noticeably, different cars may be separated out for special preparation. 7. Rock or equipment may be loaded and moved out of the mine without interference with the production or preparation of the coal. 14.1.1-MINE CARS Mine cars with steel bodies are used in all types of present-day mining. Wooden cars usually are more bulky and less resistant to wear and damage, but are more easily repaired. Regardless of the type of mine car selected, it is most practical to standardize on one type or make to simplify repairs and limit the amount of spare parts necessary to stock. Rigid-body flat-bottomed cars are simpler and usually lower than others of equal capacity. Advantages are: ease of loading because of the low sides, simplicity, cheapness and high ratio of capacity to weight. The disadvantages include the

Jan 1, 1973