Search Documents

By Holbrook G. Botset

Experiments performed in this laboratory on the flow of gas-liquid mixtures through unconsolidated sands have been described and discussed in an earlier paper.4 In these earlier experiments a definite relationship was found between the liquid saturation of a sand and its permeability to the liquid or gas phase. Furthermore, the nature of the sand, the permeabilities of the sands over a range between 17 and 260 darcies, appeared to have a negligible effect upon the saturation-permeability relation. Likewise experiments indicated that the viscosity of the liquid, or the substitution of an immiscible liquid for the gas phase, had only a very slight effect on the permeability-saturation relation. This conclusion has since been definitely confirmed by the experiments of M. C. Leverett3 on the flow of oil and water through unconsolidated sands. The sands used by Leverett were of very low permeability (between 6.8 and 1.04 darcies), while the oil-water viscosity ratio varied between 90 and 0.057. Since the sands that constitute petroleum reservoirs are largely consolidated, although of widely varying degrees of consolidation, it was desirable to extend the experiments on gas-liquid mixtures to consolidated sand. In the study of consolidated sands additional variables are involved, but for the initial experiments the only new variable to be introduced was the cementing material. Experimental Procedure A comparatively limited assortment of sandstones was available for the selection of the experimental material. Of these, the Nichols buff sandstone appeared to be most suitable. It gives no visual evidence of any bedding planes, it has a firm structure, permitting easy handling, and its permeability is about 0.5 darcy. Its only disadvantage is the fact that it contains an appreciable amount of ferric oxide which, for experiments involving water, will hydrate and reduce the permeability. This

Jan 1, 1940

By D Thornton, B Smith, S Demey

Mine to Mill (MTM) optimisation, a total systems approach to the reduction of energy and cost in mining and mineral processing operations, is well-established technology. However, successful applications of MTM optimisation have been largely confined to gold, copper and lead/zinc semi autogenous grinding (SAG) operations, where the goals of tweaking the blast design to increase fines and hence throughput through the mill have been relatively easy to meet. The application of MTM optimisation in a more demanding environment, like that of a multi-stage crushing and screening aggregate operation, was conceived as part of a Department of Energy (DOE) initiative in 2004, aiming to reduce the energy consumption in the US aggregates industry. Two quarries operated by the Luck Stone Corporation of Richmond, Virginia, were selected for the demonstration sites. Dealing with ore variability and a requirement to maintain a fixed feed size distribution to the tertiary plant, whilst still aiming to increase yields of saleable products, presented some unique challenges. Despite these variables, the implementation of the MTM approach at Luck StoneÆs aggregate plant in Pittsboro, North Carolina, has led to a tangible improvement in productivity, particularly in the primary and secondary plants. The successful outcome was dependent upon several key factors, including reliable blasting and processing models, careful analysis of the rock conditions and plant configuration, understanding and buy-in from the Luck Stone operations staff, excellent collaboration with Virginia Tech staff and students, and long-term monitoring made possible through comprehensive PLC logging. This paper presents a review of the work conducted at the Pittsboro quarry and highlights the key reasons behind the successful implementation of the MTM approach in a complex plant environment.

Jan 1, 2007

By G. B. Pryde, R. M. Magraw

In laying out a new mine, provision should be made for the ultimate recovery of as much coal in any given bed as is consistent with safety and economic mining. Though each mining district, if not each individual mine, has problems that make the adoption of any hard and fast rule impossible, certain basic principles are adapted to practically all conditions. One of the most vital is the provision for barrier pillars of ample dimensions to protect all haulage and permanent airways during the life of the property. Where conditions permit, room or butt entries should be driven on the strike or slightly to the rise, and rooms turned at right angles to these entries. The width of rooms and room pillars is governed by conditions prevailing in the mines under consideration. A safe rule is: In advancing, extract not more than 25 to 35 per cent. of the entire seam; in exceptionally thick seams, considerably less than 25 per cent. should be taken. Rooms usually vary in length from 250 to 350 ft. (76 to 106 m.) with a barrier pillar of not less than 80 ft. between the last crosscut. in rooms and the back entry of the level above. All entries, rooms, and entry-and-room crosscuts should be driven .on sights and room crosscuts should be driven at, right angles to the direction of the rooms. In mines under excessively heavy cover or where roof conditions are bad, rooms should be driven narrow and a barrier pillar left at every fifth to tenth room. This barrier should be of such dimensions that one or more rooms, with pillars of usual dimensions, may be turned through it when the barrier is no longer required. Two of the advantages of such a barrier are the protection of the panel against peaking of roof load during pillar extraction and the easy closing of the entry in case of fire. Where economic conditions permit, it is preferable to follow the retreating panel system of mining. In the case of coal that outcrops, and even in cases where no outcrop is exposed, it is preferable to commence pillar extracting on the high side of the mine. Where the retreating

Jan 1, 1922

By Cerutty L

To those who have been engaged in the construction of mining and metallurgical plants during the war and post-war periods, it is quite unnecessary to point out the large increases and violent fluctuations in prices of basic commodities and the steady and persistent rise in labour costs. It may, however, be of interest to present these facts in graphic form, and survey the relative heights of the various maxima and the lead and lag of individual waves. Since Descartes demonstrated for us moderns the analogy between geometric form and algebraic statements, the two-dimensional graph has found widespread application. Mathematicians have developed for our information, if not for our confusion, the triangular diagram and the solid three-dimensional figures, which have proved so useful, at least in the hands of the metallurgists at Port Pirie. The model (Plate 1.) which is exhibited here does not pretend however, to indicate the connection between any three inter-related variables, and it is not proposed to burden members with any abstruse mathematical expression for the irregular surface of the blocks. While time is an ordinate common to all sections of the model, each illustrates separately the variation in cost of some particular quantity between the years 1914 and 1922. It is an easy matter to record such individual variations, but it would be an impossible task to state any equation describing accurately the dependence ot the prices, say, of hardwood or of galvanized iron upon that of labour at any particular point of time. The cost of living curve, which has attained such prominence, if not notoriety, in the last few years, is the result of an attempt to show the mass-effect of the components. It is the difficulty found in "assigning the correct weight to the separate items which makes the aggregate curve somewhat misleading at times.Turning to the model, it will be noticed that each section consists of half a dozen pegs.. The first in each row,that coloured red, represents the cost of some particular quantity, such as bricks, timber or coal, at Broken Hill in 1914. The next peg, that coloured blue, represents proportionately prices for that quantity in Hobart during...

Jan 1, 1922

By Theodore A. Blake

More than a quarter of a century has passed since the introduction of the machine known as the Blake crusher, the invention of Eli W. Blake, of New Haven, Conn. Although originally designed for breaking stone for road-metal, its importance for crushing ores of the precious metals, and those of iron, copper, and zinc, as well as emery, phosphates, plaster, etc., mas soon recognized, and for many years its use has been world-wide, and its construction so well known that no special description of it is deemed necessary. Following its introduction, many different machines for the same purpose, containing the same essential features of upright convergent jaws, one of which is movable with respect to the other, hut having some slight modification of such movement (generally a rubbing motion) or of the non-essential method of imparting motion to one or both of the jaws, have been offered to the public for sale and use, but have, as a rule, in time disappeared from the market. If we seek for the reason of the success of the Blake crusher, aside from its simplicity of construction, we shall find it in the adherence to the principle of crushing by simple pressure and careful avoidance of attrition. In this lies the economy of power and of wearingsurfaces. To reduce any hard and brittle material to a fine powder by many different methods—by attrition, impact, or percussion—is a comparatively easy matter; but to accomplish this by the employment of either of the above-mentioned principles involves such a consumption of wearing-surface? (generally iron) or of power, that the numerous devices that have hitherto been presented to the public as solutions of the problem of fine crushing have proved utter and complete failures when tested with reference to the power employed and the wear of iron in doing their work.. Aside from the use of crushers with the harder ores, the only two methods of fine crushing in general use, and, in the writer's opinion, worthy of consideration, are by means of stamps and rolls; the former doing their work by percussion, the latter by pressure, provided

Jan 1, 1885

By Roswell H. Johnson

The principle of sliding or graduation in royalties is accomplished either by the block, period, cumulative, or class method. The block method calls for a very low royalty rate on all oil produced up to a certain amount. This amount would normally be that which is believed to suffice to repay the cost of the well. A higher rate would be charged after the well is making a profit. This method, common in many industries, is peculiarly inadaptable to any industry such as this where the productivity per day of the units gradually and inevitably decreases. This, for reasons given later, is because it forces an early abandonment of the well and so offends against conservation. In the period method, the royalty rate is changed by some definite amount when the well produces less than a specified quantity per day or other given unit of time. While simple to explain, it operates badly because a great deal is made to depend upon a small reduction in production, whereas the reduction as a matter of fact declines rather erratically owing to the exigency of lease management, connecting of tankage, and vagaries of the gaugers. These disadvantages are obviated by the cumulative method. In this method, all the production less than a certain amount per week has one rate of royalty, or none at all, and the oil produced in excess of that amount pays an additional rate of royalty. In the long run the calculation is probably no greater than with the period method, for simple tables will be published and printed in the oil papers that can be cut out, enabling quick readings to be made. Even without the table the calculation is easy with the few royalty rates, two or three, which would be used. In this method, the amount paid in royalty declines gradually, rather than suddenly as in the period method. The following reasons might be advanced for the adoption oi cumulative royalties: 1. To distribute the burden in accordance with the capacity to pay. This principle is a unique one in business, although familiar in taxation. This is because it does not distribute reward in proportion to efficiency.

Jan 1, 1916

By Howard R. Hughes

In drilling for water and oil to reasonable depths through the generally soft yielding clay and sand formation of the Coastal Plain of Texas, Louisiana, and Mississippi, the rotating method of drilling was adopted, principally on account of the easy and quick penetration, and the low cost of the drilling plant. In favorable ground, free of heavy gravel and rock strata, as much as 1,600 ft. has been drilled in less than 36 hr., although such performances were of course rare. Hydraulic rotary drilling, or, as it is now called, rotary drilling, was used in the above States as early as 1880. The plant consisted of an ordinary derrick, a 25-h.p. boiler, a small hoist, a steam pump, and a water swivel with hose attachment, and an ordinary flat diamond-pointed bit. The successful drilling in of a phenomenal oil well by this process on Spindletop, near Beaumont, Texas, on Jan. 10, 1901, and the ascertained impracticability of drilling subsequent wells in the same locality by other methods (owing principally to heavy quicksand under pressure from below), brought rotary drilling into great prominence, practically to the exclusion of any other process throughout the Coastal Plain, and later on elsewhere. The method, as its name implies, involves the rotation of a pipe by means of machinery placed on the derrick floor. A drill bit attached to the lower end cuts a clearance for the drill pipe, with much the same motion and effect as an auger. Water forced through the drill pipe by means of a pump, and escaping through the bit, removes the cuttings and returns to the surface outside the drill pipe. In this manner the hole is kept open, permitting the drill stem to rotate freely. The pressure of the column of muddy water holds up the walls of the hole until it has been cased. Practically all the wells of the Gulf coast region, numbering nearly 10,000, have been drilled with this system. During the last five years its use has been extended to many other States and countries.

Jan 1, 1915

By Arthur L. Flagg

The Elk City mining district of Idaho occupies a position near the geographical center of Idaho county, a region of moderate elevation in the western foot-hills of the Bitter Root mountains. The district comprises an area of approximately 350 Sq. miles, bounded on the west by the Newsome district and on the south by the Dixie and Oro Grande districts. There are no mining districts to the north or east. Elk City, the principal town and the seat of the mining office for the district, is situated in a hydrographical basin surrounded by low hills. The elevation is 4,200 ft. above sea-level. Through this basin flow Elk Creek, Red river, and American river, which unite west of town to form the south fork of the Clearwater. The one township is set out from the Bitter Root Forest Reserve. Though a railroad starting from the Stites terminus of the Clearwater Short Line of the Northern Pacific railroad has been under consideration for some years, the camp is yet without railroad facilities. The projected road would follow the south fork of the Clearwater on easy grades, but would be very expensive to build and maintain. While such a road would greatly benefit those who are now operating in the camp, and in a sligh degree stimulate interest in its possibilities, there is hardly business enough to warrant its construction. At present all supplies and equipment are hauled in by wagon from Stites, a distance of 58 miles, over a wagon road constructed by the State in 1904, following in the main the old Nez Perce trail. While this is not a bad road, it is not all that might be desired. Starting at Stites at an elevation of 1,327 feet above sea-level, the road runs through low hills to Clearwater, a distance of 10 miles. In the next 16 miles the climb is steady until the Mountain House is reached, which is near the summit of Mount Pisgah. This is the highest point passed on the road, having an elevation of 6,500 ft. From the

Jan 1, 1914

By Francis A. Pocock

The writer is continually asked, if this electricity:is all you claim for it, why do not the mines put it in and use it? The best answer was given by Mr. John Fox Tallis, in his paper read before the South Wales Institute of Engineers in 1888, namely, that the reasons are similar to those which have prevented the more general employment of other systems of haulage. Managers, as a rule, are " not experienced mechanical engineers; neither are they all versed in electrical engineering." It may be said that there are a number of " able and practical electrical engineers who could do the work; but those electrical engineers are not conversant with the practical routine of colliery work and are, therefore, placed at a disadvantage by not knowing the actual requirements of mining engineers, and the many little difficulties to be met and contended with in underground workings; and, until mining engineers have acquired the necessary knowledge and a confidence in electricity, it is only natural that they will continue to follow the beaten path." In the above remarks, Mr. Tallis has hit the nail on the head. In the face of the partial failure, financially, of the haulage-plant which the Union Electric Company of Philadelphia had set to work at Lykens Valley, Pa., an electric haulage-plant was installed near Scranton, Pa. The question was not whether electricity could do the work, but whether any electrical company knew enough about the practical difficulties to attack and overcome them. That point being settled, the remainder was easy. The contract for the Erie Colliery haulage-plant was signed in January, 1889. This colliery is owned by the Hillside Coal and Iron Company, Mr. Samuel Hines, President, and Captain W. A. May, Superintendent. The company has been using arc-lamps in its breakers for three years. It is the only company in the Lackawanna Valley which has had enterprise enough to do so. Consequently, it was acquainted

Jan 1, 1890

By R. R. Estill

THE rank of the Ruhr coal ranges from a high volatile bituminous coal to an anthracite, depending to some extent on the original depth of the seam. The average Ruhr coal corresponds to a soft bituminous American coal of a coking quality. The average thicknesses of individual coal seams being mined are also comparable (59 in. against 65 in. in the United States). However, consideration of seam conditions and mining conditions other than those just mentioned emphasizes differences rather than similarities with United States soft coal. In general, the Ruhr seams now being mined are much more folded and inclined than American seams. Dips of 20" and 30" are common in seams now being worked, and 30 pct of the coal reserves in the district are in seams dipping more than 35". Only on the tops and bottoms of folds do we find rather flat coal seams. In addition to the folding there is extensive displacement by cross faulting plus a certain amount of strike faulting of an overthrust nature, which results locally in doubling or omission of seams. Because of the long history of mining in the Ruhr, nearly all coal lying near the surface has long since been mined out, and we find that the average depth of mining is at present about 2300 ft below the surface. Deep mining, folding, and faulting result in seam conditions requiring a great deal more roof support than one finds in American soft coal mines. In fact only in the anthracite district and the Rocky Mountain and Pacific coal fields do we find somewhat similar conditions. It is easy to say, therefore, that the problem of mechanization of coal cutting and loading in the German mines is quite different from that which we have so effectively met in America with our mobile cutters and loaders, duck bill loaders, and a room and pillar system of mining our drift and slope mines.

Jan 12, 1950

By C. S. Barrett, C. T. Haller

TWINNING in magnesium is known to occur profusely under certain conditions, and when it occurs in polycrystalline materials it brings about a partial or even a complete change in the preferred orientation. The amount of research on this subject, however, has not been in proportion to its importance as a mechanism of deformation and reorientation. Much of the research has been limited to twinning in single crystals. The present study' concerns polycrystalline sheet, and is an investigation of the twinning produced by plastic deformation as a function of the following variables: I. Direction and type of deformation. 2. Amount of deformation. 3. Speed of deformation. 4. Temperature of deformation. 5. Composition and temper of the sheet. 6. Twins previously produced. 7. Twins previously produced, then annealed. By proper control of these variables it is shown that, on a laboratory scale, samples can be produced that are free from preferred orientations. MATERIALS AND METHODS The materials used were samples of commercial magnesium-alloy sheets with nominal compositions given in Table I. [ ] X-ray diffraction was used in most of this work to detect the twins and to estimate the amount of twinning. Since twinning on {102} planes causes a reorientation of the crystal lattice by 86°, it is very easy to study with X-ray diffraction patterns, particularly if one notices the diffraction ring from the basal plane the 002 reflection. By properly directing the X-ray beam, it is possible to produce 002 reflections from twinned material at, say, the 6 and 12 o'clock positions on the 002 ring, with the untwinned material reflecting to 3 and 9 o'clock positions; and by judging the relative intensity of the arcs on the diffraction ring at these positions, it is possible to judge the amount of twinned material relative to the untwinned. This X-ray method of estimating the amount of twinning is generally superior to metallographic observation, for it was found

Jan 1, 1946

By W. Petruk

A study was undertaken to determine whether interrelations between mineral grains affect ore breakage during grinding, and to establish a correlation between ore breakage and mineral liberation. A base metal ore from the Brunswick No. 12 deposit in New Brunswick was ground for different periods of time in a laboratory ball mill, and both the unbroken ore and the ground products were analysed by image analysis. The results show that the mode of breakage is strongly influenced by the behaviour of pyrite. Similar size distributions were obtained for material from the 15 minute grind in a laboratory ball mill, for the grinding circuit discharge from a commercial mill, and for pyrite grains in the unbroken ore. This similarity indicates that a 15 minute grind breaks poorly bonded pyrite grains along grain boundaries, and represents the limit of easy breakage for the ore. Such a grind liberates both large separate grains of ore minerals and poorly bonded mineral grains that occur in interstices among pyrite. On the other hand the 15 minute grind does not separate moderately bonded mineral grains nor release moderately bonded interstitial minerals from pyrite; a 45 minute grind in a laboratory ball mill is required. It is assumed that, for Brunswick No. 12 ore, a 45 minute grind in a laboratory ball mill is equivalent to regrinding in a commercial mill. Grinding beyond 45 minutes in a laboratory ball mill breaks the ore by fracturing pyrite across grain boundaries and by chipping grain edges. Such intense grinding does not markedly increase sphalerite liberation from Brunswick No. 12 ore, because most of the sphalerite that can be released was liberated at the 45 minute grind. In contrast the intense grinding increases galena liberation because a significant proportion of the galena occurs as minute inclusions in pyrite. These findings show that ore breakage and coincident liberation depend upon size distributions, intergrowths, and mode of occurrence of the minerals in an ore.

Jan 1, 1988

By Richard Moldenke

The author discusses some economic conditions which have made the career of the cast-iron pipe industry in the United States a checkered one. He next describes the two new developements in the manufacture of cast-iron pipe-both along the lines of centrifugal casting. The advantages and disadvantages of both processes are presented in some detail. Finally, statistics on the production of pipe in the United States at the present time are given, as well as the plants-and their capacities-so far as these are situated in the South. No SINGLE branch of the foundry industry has been brought to a production basis of huge tonnage, low manufacturing cost, and producing material of a remarkably high quality, as has the making of cast-iron pipe. The pipe shop is an excellent illustration of the fact that repetition work in specialties leads to mechanical equipment and manipulation that lower production costs to an. astonishing degree. Hence cast-iron pipe, in dull times, has been sold at a few dollars a ton over the selling price of the pig iron used. On the other hand, these same pipe, shops make fittings .of many varieties, and in much smaller quantities, where the cost is high, and when pipe may be sold, say, at $50 a ton, the fittings on the same shipment will be sold for nearly double that price. The history of pipe-making, in the United States, is a checkered one the mortality of plants is high and, from the nature of the industry, plants must be large to live. In spite of the fact that the best processes must be used to turn out this rather strict specification material, pipe is easy to make and a pipe plant is more of a tonnage mill than the really high-class specialty foundry it should be. Every time, therefore, that the demand for pipe is strong new shops spring up, only to close when the demand has ceased, but the financial damage to the more permanent plants has been done. Both the South and the North have had abundant experiences of this kind, and when recently a northern Public Service Corporation gave its order to France, the pipe plants thus adversely affected were content to have this occur rather than see-a plant started to supply the surplus demand.

Jan 9, 1924

By D Wiseman, R Dunne

Flash flotation is a process that is included in many new mineral processing plants as part of the grinding circuit. Some of the valuable minerals can often be liberated at coarse sizes and will remain in the recirculating loads of the mill until they are reground small enough to report to the cyclone overflow. In addition, minerals of high density report to the cyclone underflow despite being fine in size. This can lead to overgrinding and makes the recovery of valuable fines by flotation difficult. Flash flotation is used to remove the readily floated coarse particles as early as possible and can therefore prevent overgrinding. It thus has the added potential to improve materials handling of the concentrates in such processes as filtration. The merits of including flash flotation within an integrated comminution-conventional flotation circuit is not easy to determine experimentally. Simple batch flotation tests are unable to provide any measure of the possible or probable improvements that are likely to occur from this circuit configuration. As a consequence expensive pilot plant programs are resorted to, to provide the information that will justify the inclusion of flash flotation into a comminution-flotation circuit. Those who have been involved in such pilot plant programs will know of the difficulty in stabilising the circuit as well as selecting the appropriate operating parameters (eg amount of concentrate to be removed in both the flash flotation and conventional flotation circuits). The interactive nature of this circuit (grinding, classification and flotation) is the root cause of these difficulties. Computer simulation, based on information derived from laboratory batch test work or plant and laboratory data, offers an alternative means by which an initial assessment of the merits of a flash flotation circuit can be determined. It can also provide the basis and focus for pilot plant testwork. Recently MacKinnon, Yan and Dunne (2003) developed a model that allows the performance of a flash flotation to be obtained within a closed circuit grinding operation. This paper provides details of an extension of this model to incorporate the interaction of flash flotation on the downstream conventional flotation circuit and allows æwhat ifÆ scenarios to be explored. Details of the laboratory batch test work methodology and the pertinent data derived from these tests that are used in the models and simulation are provided.

Jan 1, 2005

By N. H. Snyder

Coal analyses help to describe the character of coal as it lies in the ground of as it may he delivered to the user Analyses of samples of coal collected from the face of the bed in mines are plentiful, but available analyses of delivered coal are relatively few, and there is a distinct difference between "mine samples" and "delivered samples.” Mine samples are collected actor drag to a standard method. 13 The sampler cuts a channel. 2 by 6 or 3 by 4 inches from roof to, floor in the face of the bed, and excludes from the sample all partings more than 3/8 inch thick, and any lenses or concretions of sulphur or other impurities more than 2 inches in maximum diameter and 2 inch thick. Analyses of mine samples form a permanent and scientific record of the coal bed at the point sampled, they ale important in determining the character of the coal in any given mine or district These analyses, when the samples are taken by a standard method, are valuable to the operator When compared with analyses of delivered coal they show him whether his mine is being worked efficiently or whether the coal is being properly prepared, which involves the ques¬tion ii Nether he has suitable mechanical appliances for separating the impurities sties. In the purchase of coal, mine samples may serve as a sufficient guide for the experienced buyer who has knowledge of the impurities in the bed, and the degree to which these are eliminated in mining and preparing the coal To the average purchaser, however, unacquainted with these details, dependence on mine samples may be misleading The quality of coal indicated by the base samples call rarely, if ever, be attained in the delivered coal Certain impurities that are eliminated from the formally prepared mine sample may not be eliminated by the miner Some of the roof and floor may also be included if these are soft or flaky When coal prices are high and competition is lessened it is easy for the miner and the management to lower the standards of preparation, and a return to rigid stand¬ards is always difficult. In sampling delivered coal the Bureau of Mines follows a definite procedure. 14 A sample of not leas than 1000 pounds is systematically

Jan 1, 1928

Blasting is at first sight a simple operation. Blastholes are drilled in a suitable pattern, primed, charged with explosives, stemmed and finally the blastholes are connected together to give the appro- priate initiation sequence. In practice the action of the explosive takes place in the interior of an opaque rock mass and only the external faces of the rock mass to be blasted can be easily observed. The mechanisms of blasting cannot be observed directly and must be inferred from observations of the free face and meas- urements of particle movement made by sensors grouted into holes in the rock. Explosives react very rapidly, in some microse- conds and any instrumentation of a blast must have an appro- priate response time. In many mines several rock types can be encountered during production. Several different methods of blasting may be necessary to cope with changes in rock types espe- cially if weak rocks are found in the final limits. This also makes it difficult to be sure of getting a large enough volume of rock to perform a series of reproducible experiments. While there appears to be agreement on the mechanism of blasting it is unlikely that a detailed understanding of how all the variables that can be encountered in practice affect blasting. The ease of assessment of the results of blasting depends on the criteria used. It is easy to isolate, measure and count over- size boulders. It is however difficult and costly to get a complete fragment size distribution. Methods used to assess blasting can vary significantly from site to site and the ways in which data are collected, presented and analysed will vary making compari- son of blasts at several locations very difficult. The definition of an optimum blast can also vary with the type of blasting. The muck-pile profile and fragmentation will be different for a dragline to that for a truck and shovel operation. In order to be able to assess blasting the mechanism has to be understood. Th rock and explosive properties considered rele- vant to blasting can then be determined. This paper discusses the generally accepted mechanism of blasting. The on-site observa- tions to assess blasting are-then listed. The mechanism of blast- ing can also be modelled and the use of modelling to optimize hlaetina ie thPn Aiernccarl

Jan 1, 1988

By Robert B. Parsons

"It is generally acknowledged that Canadian and foreign-based mining companies are spending relatively fewer dollars in Canada and more dollars abroad than was the case not many years ago. It is common to see the Canadian tax system being fingered as one of the causes in this shift in direction. However, if one takes the time to peel away the surface of our tax system, and to probe a little deeper into its substance, it will be found that the Canadian taxation of mining is generally quite competitive. IntroductionCross-border shopping in the mining industry? - Absolutely! Economics 100 teaches that dollars are votes in the capitalist system, and mining companies are going to cast their limited number of votes where they can achieve the highest return at the least risk. The Canadian consumer knows that taxes are a major factor in cross-border shopping, and mining company executives know that the same tenet holds true in their industry. Unfortunately, mining operations are subject to such a bewildering array of tax rules that making an intelligent decision is not always an easy matter.Statutory Tax RatesConsider, for example, the ""statutory"" tax rates shown in Table 1. (Statutory tax rate in this table refers to the simple sum of federal and provincial tax rates on profits as specified in the tax legislation.) Looking only at the total statutory tax rates (such as 66070 for Manitoba) , one might quickly observe that the Canadian mining industry is subject to a truly onerous tax regime, especially as compared to the United States where statutory tax rates can be in the 34% range."

Jan 1, 1992

By C. S. Roberts

Microstructural studies of a Mg-10.3 pct Al alloy showed that discontinuous precipitation during aging multiplies the grain boundary area available for easy deformation in elevated temperature creep. An increase of strain rate for a 6.2 pct Al alloy at 400°F, where precipitation and creep are concurrent, caused an increase in the volume percentage discontinuously precipitated at the completion of the process. The relatively poor elevated temperature creep resistance of heat treated alloys of the Mg-AI-Zn type was explained in these structural terms. C resistance of the heat treatable Mg-A1 based alloys is poor compared to that of Mg-Ce based alloys. While the latter show a continuous precipitate, Mg-A1 alloys prefer a discontinuous precipitate at grain boundaries. '.:' It has been concluded that the excellent creep resistance of Mg-Ce alloys was primarily due to the continuous precipitation which especially localized at the grain boundaries.' The purpose of the present investigation was to obtain a parallel correlation, if such exists, between the poor creep resistance and the state of precipitation in Mg-A1 alloys. Discontinuous precipitation produces about three times as many true grain boundaries as originally existed. This microstructure would be expected to have a marked influence in creep, where quantity of grain boundary area is important. Experimental Procedure The two experimental alloys contained 6.2 and 10.3 pct Al. They were made from electrolytic magnesium by alloying under flux and casting in 3 in. diam permanent molds. The ingots were extruded into 1 1/4 x 1/8 in. flat stock under the following conditions: billet preheat 700°F (2 hr), container and die temperature 700°F, speed 3 fpm, and area reduction ratio 45:1. The creep specimens were machined from blanks which had been solution heat treated 24 hr at 770°F and aged 16 hr at 400°F. Attempts were made to control the grain size as closely as possible for extruded stock. The grain size after solution heat treatment was about two thousandths of an inch for the 6.2 and five thousandths for the 10.3 pct Al alloy.

Jan 1, 1957

By Julien F. Phillips, Donald E. Garrett

The production of soda ash from natural sources is one of the United States' oldest industries. The London Company, which financed the settlement of Jamestown, in the fall of 1608 exported in its first cargo from Virginia " . . . trials of pitch, tar, glass, frankincense, and soap-ashes."1 This last product, a crude mixture of sodium and potassium carbonates obtained by the burning of wood in iron pots, was the commercial soda ash of its day, used in the infant soap, glass, and bleaching industries. Besides having a good cash value, its production helped to clear the land, and it was a compact, easily shipped commodity. The extra high potassium content of these American "pot-ashes" gave them an added market as a fertilizer, a field that they dominated until the opening of the Strassfurt deposits in 1860. This form of natural soda ash disappeared forever from commercial importance with the introduction of the Le Blanc process (1791), and later the Solvay process for manufacturing soda ash. The Solvay process was rapidly accepted in the United States, and has accounted for most of the country's soda ash production since 1884. It was not until the western part of the country began to be developed that natural soda ash was again produced. A number of lakes, playas, and springs west of the Rocky Mountains were found to be rich in this mineral, and climatic conditions were ideal for its easy recovery by solar evaporation. The production of natural soda ash from these deposits has become a steadily growing industry in the United States. Production A summary of the production and value of natural sodium carbonates in the United States is presented in Table 1. Prior to 1927 the principal output came from several different companies at Owens Lake, California. Then production at Searles Lake, California, began to [ ] increase until it became the most important source. In 1948 the sale of crude trona from Green River, Wyoming, commenced and since that time production from these latter two areas has been about equal. Table 2 lists the four

Jan 1, 1960

By Greg Hodges

Sand-and-gravel aggregates have become the number-one, nonmetallic-mineral resource in the world. Surficial aggregate deposits of economic size are becoming increasingly rare in most parts of Canada. In southern Saskatchewan, this is especially true, and detection and delineation of intertill sand-and-gravel deposits with airborne electromagnetic (EM) surveys have proven very successful. Airborne and ground geophysical surveys detect such deposits by their resistivity contrast relative to the surrounding clay-rich soils. Dighem helicopter-borne electromagnetic surveys map soil variations over a large area quickly and cost effectively, greatly reducing the cost of detecting and mapping deposits compared with traditional methods (air-photo interpretation, ground EM, and drilling.). The multiple-frequency EM system used by Dighem can map variations both horizontally and vertically. Magnetic data collected simultaneously are useful in mapping bedrock geology. Both resistivity and bedrock maps aid in the important task of reducing drilling costs and person-hours in the field. The results of the survey are presented as maps of ground resistivity, which are relatively easy to interpret. These maps are produced in the field at the time of the survey, making quick follow-up of the survey possible. Airborne EM surveys can map the extent and depth of aggregate deposits more effectively than is practical from the ground. Since aggregate deposits can vary tremendously in a very short distance (<300 m) large-area EM maps can show both local area variability and also help develop intertill trends. A test survey for the Saskatchewan Highways and Transportation Department over a 3-km by 5-km area mapped all the known deposits as well as some unknown deposits, subsequently proven by drilling. The test-survey data show that the method not only detected the deposits, but also gave an estimate of the shape (volume) of each of the deposits. Comparison of the data to drill sections shows excellent correlation. Theoretical modelling demonstrates that the multifrequency system can discriminate sand and gravel from bedrock ridges. Since the successful test work, about 725 km2 of ground have been surveyed, resulting in the discovery of four new deposits, which can be used immediately, resulting in significant savings for the Saskatchewan government and taxpayer.

Jan 1, 1999