Search Documents

By Arthur E. Lord, W. Martin McCabe, Robert M. Koerner

Following the driving of each new section of tunnel, a prompt decision is required regarding the type and extent of primary support to control convergence and prevent ground failure. Sometime thereafter, the effectiveness of the in-place support must be evaluated over the entire length of excavation. It is therefore extremely desirable to have available a lightweight, portable, easy to install and interpret, cost effective monitoring system to assist with these ground control functions. Such a system can be assembled based on the acoustic emission (or microseismic) technique. This monitoring technique uses a piezoelectric transducer to detect subaudible noises associated with deformation of and/or crack propagation in the soil or rock being monitored. After detection, the signals are then amplified, filtered and electronically counted to provide a quantified assessment of the stability of the structure. In the simplest sense, the absence of emission, or counts, signifies no deformation and thus stability. Conversely, the occurrance of counts signifies instability to varying degrees. The higher the count rate, the greater the instability and the need for immediate or additional support. Described in this paper is an overview of the acoustic emission (microseismic) method, details of its use in a laboratory study measuring convergence and stand-up time in soil, and the behavior of rock samples under similar stress conditions. Field use of the method is recommended for ground control monitoring in tunnels, and some suggestions regarding monitoring procedure are presented.

Jan 1, 1979

By John P. Norton

Microcrystalline silica has been mined in Illinois from the Clear Creek Formation since the turn of the century, especially in the area around Tamms in Alexander County, in the southernmost part of the state. This silica is consumed mainly by the abrasives and coatings industries, but is also sought after for many filler/extender uses. Production has grown with the economy with several new applications overshadowing traditional markets in recent years. Many of these applications are directly or indirectly related to energy saving factors. As a result of the "energy crisis" and "resin crunch," fillers have received a great deal of renewed attention as a desirable way of stretching the available resin supplies. With feedstocks in short supply and shortages existing in the entire petrochemical industry, the use of bulk materials to improve and extend existing resin is becoming an every increasingly important facet of plastics and coatings technology. Silica is the choise of fillers in applications where inertness, hardness, and low absorption are necessary characteristics. Microcrystalline silica has the additional advantage of being relatively easy to grind because the crude ore is a friable rock composed of tiny crystallites, many less than 0.1 u in diameter. Grinding represents a significant energy input in the production of silica flours. With energy costs increasing rapidly, comparable grades of silica flour made from microcrystalline silica have advanced less in price and it is expected this trend will continue in favor of the microcrystalline silica.

Jan 1, 1978

By Ray Schmidt

When your committee approached me for a talk on "Mechanics of Secondary Metals Collection," I replied that this subject would probably not be very interesting to a group of engineers and requested permission to dwell on the Westinghouse Salvage Setup. I will attempt to avoid duplicating the points covered by Mr. Bliven. The Westinghouse Electric and Manufacturing Co. has main manufacturing Divisions in 25 cities and 9 different states, scattered throughout the country, as well as Naval Ordnance Plants in two midwest cities, and a Merchant Marine Turbine Plant, and two special War Production Plants in Eastern cities. You can, therefore, see that we must have a well rounded pro- gram with the entire respect and sponsorship of the various Division Managements. That was not so easy to get. Management has been a great deal like the general public in the past. I am sure most of you can remember the not very ancient day when each town had a ragman who had a horse and wagon and went through the streets of the town, from door to door, picking up what scrap he could accumulate. He was known as a junk man, and indeed, with the exception of the very last few years, the attitude of manufacturing management was: "We have a job to do. We have a product to manufacture. We don't have time to bother with the junk business."

Jan 1, 1943

By D E. Langberg, D R. Swinbourne

The past century has seen the development and commercialisation of many new pyrometallurgical processes based on gas injection. The driving force behind this trend in smelting and refining technology was the increased productivity and resulting increase in capital utilisation achievable. However, measurement of system variables is not easy and their effect on the rate of the reactions involved is not well characterised. One of the critical parameters is the gas-liquid interfacial area produced by gas injection. Related variables such as bubble size and velocity, and gas hold-up fractions in aqueous systems have been measured using combinations of physical (visual, audio and electrical) and chemical techniques. Models have been developed relating interfacial area to physical properties and operating variables and attempts made to extrapolate these to high temperature, liquid metal systems. The only attempts at validation of these models have used either low temperature liquid metals, such as mercury or WoodÆs Metal, or operating plant data. This paper reviews existing knowledge of the effects of system variables on total interfacial area in gas injection systems. Interfacial area is calculated from a range of published experimental aqueous and liquid metal systems and used to assess existing models. An operating region diagram was developed to assess dynamic similarity between experimental and industrial systems. It highlights areas where further research into both measurement techniques and experimental system variables is required in order to extend knowledge and guide further technical and design advances into the 21st century.

Jan 1, 2000

By M. Rudman, L. Pullum, L. J. W. Graham

Centrifugal pumps are the workhorse of hydraulic conveying systems but their performance is derated when viscous non-Newtonian fluids, such as pastes and/or coarse solids are present. The reduced performance for purely viscous Newtonian fluids may be calculated using techniques such as the Hydraulic Institute method, but similar deration for non-Newtonian fluids is not so easy to apply. As part of the AMIRA P599 project investigating high concentration suspension pumping, centrifugal pump tests were systematically conducted on a wide range of non-Newtonian coarse particle suspensions. Suspension sup to 38% v/v of coarse particles with mean diameters in the range of 1.1 < d50< 3.4 mm suspended in carrier fluids with dynamic yield stresses of 0 < t?< 17.2 Pa and shear thinning indices in the range 0.35 < n< 0.79 were examined. Techniques such as the Hydraulic Institute de-ration method require a characteristic shear rate to be assigned before application with a non-Newtonian fluid, and a method based on pump geometry, fluid rheology and flow rate is proposed. This method predicts the dramatic characteristic reduction in head at low flow rates that is often observed and explains why larger pumps are relatively insensitive to this form of head deration. Head deration due to the presence of coarse particles in non-Newtonian carrier fluids is seen to follow similar trends to that of Newtonian suspensions and often dominates the total deration procedure.

Jan 1, 2007

By Y. C. Kim, W. L. Meyer, W. Cai

Although the first published optimum pit limit design algorithm by Lerchs-Grossmann dates back to 1965, the majority of the open-pit mines in the US has not as yet adopted such a rigorous optimization algorithm. Instead, the floating cone approach initially developed by Kennecott Copper in 1961 is still used today for various reasons. However, shortcomings with the floating cone algorithm, particularly for precious metal deposits with erratic mineral distributions, have provided a renewed interest in optimizing algorithms. This paper compares the performance of the floating cone algorithm with the rigorous optimization algorithm of the Lerchs-Grossman&apos;s graph theory and the newly developed maximum network flow algorithm by Hanson (1986). The maximum flow algorithm is a modified version of the logic as initially advocated by Johnson in 1968. Comparisons are made for three different deposits in terms of the total profits generated and the computation times involved. The results of the comparison show that both algorithms produced higher total profitability pits than the floating cone in all three deposits, although the increase in profits never exceeded 1 % of the base design obtained using the floating cone. Between the graph theory and maximum flow, graph theory produced consistently higher profits. The current version of maximum flow, however, cannot be modified to produce the optimum pit. Nevertheless, the authors prefer the maximum flow over the graph theory, simply because it is easy to program as well as to explain.

Jan 1, 1987

J. L. McK. YARDLEY,* Pittsburgh, Pa. (written dlscussion ?) .-It is interesting to observe how closely Mr. Hansen agrees with other investigators to the effect that the art of electrolytic zinc has left the realm of mystery. In his introduction, lie has said practically what Thomas French said in his paper "The Future of Electrolytic Zinc. "1 The successful electrolysis of zinc from sulphate solutions has not been an easy matter, and it is only within recent years that the difficult problem of depositing high-grade zinc has been satisfactorily: accomplished on a commercial basis. The principal requisite is. that the electrolyte shall be quite free from certain impurities. The methods by which freedom from these impurities is assured are now very well understood, and with experienced superintendents there is little difficulty in obtaining a high efficiency in that part of the process. When certain underlying principles are recognized, the difficulty encountered in dealing with the filtration of the acid and slimy solutions also largely disappears, although it has been a very serious one to the uninitiated. In the dissolving of the zinc from the roasted ore, there is nothing which any competent chemical&apos; engineer cannot undertake, and any other operations connected with the electrolytic process are either of little or no difficulty, or are common to the retort process. Mr. Hansen also agrees with R. G. Hall&apos;s statement in " Some Economic Factors in the Production of Electrolytic Zinc:"2

Jan 10, 1918

By M. J. Richards, T. X. Ren

Determination of the state of an underground fire plays an important role in fire fighting, rescue and reopening operations. This is normally achieved by the analysis and interpretation of fire gases taken from the fire zone. However, drawing conclusions from gas analysis is not an easy task and needs specialist skills, expertise and experience that are usually beyond the knowledge of the officials in a mine. The complexities of a mine fire and the uncertainties of available information often make effective fire fighting decisions difficult if not impossible. This paper describes a knowledge based expert system that can aid in the diagnosis of sealed coal mine fires. Using a commercially available shell, the expert system has been designed to accommodate a series of diagnostic rules replicating the reasoning logic that would be used by human experts. The system allows the diagnosis of explosibility of the fire zone and trends of various fire ratios to be easily visualised for decision making. By continuously analysing the incoming information, the system is able to provide a rapid assessment of the situation of a sealed mine fire prevailing under specific mining and geological conditions. In addition, short term trends in fire behaviour can be predicted and possible fire control actions recommended. An example is given and shows how this system can be used as an analytical tool in various ways to assist the combating of coal mine fires. Further development of the system is discussed.

Jan 1, 1993

A simple method of designing effective fill drainage systems for slurry backfill is presented. By using the proposed method, it is easy to calculate and predict the expected fill drainage rates or to provide additional drainage systems to accelerate the fill drainage. The fundamentals of hydraulic fill and an efficient method to determine its permeability is also explained. The safety in hydraulic filling and bulkhead stability depends totally on achieving effective drainage regime for the fill. This paper provides the basis for creating such efficient drainage regimes. The recent fatal fill bulkhead failures in Australia were the result of poor drainage from the respective fill masses, and therefore it is more important to provide suitable drainage arrangements to continue using hydraulic fill to the benefit of the mining industry. At present there is no procedure available to mine operators to estimate the expected bulkhead pressures to design a satisfactory bulkhead. Some mines are constructing bulkheads after their initial investigations carried out years ago. Other mines have simply borrowed the ideas from the pioneer mines and using in their areas. It is high time that we develop a rational approach to estimate the expected bulkhead pressures for the design of bulkheads. We need a simple model that could be understood and used by the mine operators on a day-to-day basis. This paper also presents a model to predict the bulkhead pressures for designing safe bulkheads.

Jan 1, 2002

By Arthur Flagg

(New York Meeting, February, 1913.) THE Elk City mining district of Idaho occupies a position near the geographical center of Idaho county, a region of mod¬erate elevation in the western foot-hills of the Bitter Root mountains. The district comprises an area of approximately 350 sq. miles, bounded oil the west by the Newsome district and on the south by the Dixie and Oro Grande districts. There are no mining districts to the north or east. Elk City, the principal town and the seat of the mining office for the district, is situated in a hydrographical basin surrounded by low hills. The elevation is 4,200 ft. above sear level. Through this basin flow Elk Creek, Red river, and American river, which unite west of town to form the south fork of the Clearwater. The one township is set out from the Bitter Root Forest Reserve. Though a railroad starting from the Stites terminus of the Clearwater Short Line of the Northern Pacific railroad has been under consideration for some years, the camp is yet with¬out railroad facilities. The projected road would follow the south fork of the Clearwater on easy grades, but would be very expensive to build and maintain. While such a road would greatly benefit those who are now operating in the camp, and in a slight degree stimulate interest in its possibilities, there is hardly business enough to warrant its construction.

Jan 4, 1913

By Stefan Boshkov, Malcolm T. Wane

THE validity and accuracy of velocity measurements underground have been questioned repeatedly by those in mine ventilation work. The general disagreement on the subject is well illustrated in an AIME publication.&apos; Although the presence of errors is readily admitted, their magnitudes are not known and often are described by practical operators merely as "great," "small," or "of no importance." The belief that errors are of academic interest only prevails because of a justifiable claim that actual volumes of air circulated are well in excess of those required by law and safe mining practices. Poor understanding of the source and nature of errors inherent in velocity measurements, coupled with questionable determination of cross-sectional area, result in faulty techniques for the purpose of expediting ventilation surveys and render doubtful the calculated volume. Often consistency of readings is confused with accuracy. A succession of check readings showing a maximum deviation of 5 pct in the measured value of velocity usually signifies nothing more than diligent application of technique in a stable ventilating current. This article discusses the errors involved in air measurements underground. Where instrument errors are presented, the treatment is confined solely to the rotating-vane anemometer, recognized as a most useful ventilation measurement tool because of its simple design and easy operation. In the following pages a positive deviation is defined as one which has to be added to the registered air velocity to obtain the true air velocity.

Jan 1, 1956

The Mount Lyell Company&apos;s concentrating mill is situated about a quarter of a mile westward of the portal of the North Lyell tunnel, which serves the North Lyell, Royal Tharsis and Crown Lyell mines, being on the 1100-ft. level of the first named. The Comstock mine is connected with the tram system at this level by five and a half miles of steam tramway, two-foot gauge being standard throughout.The plant is well placed with regard to all essential services and has an excellent water-supply from a series of three dams on the West Queen river.MILLING ORESThe mill feed is a mixture of the outputs from the foUr mines mentioned, each of which has its characteristic ore, but, generally speaking, about half of the ore consists of siliceous schists and the other half of hard grey quartzite. The schisty ores are easy to crush, but, on grinding, while the schist slimes readily, the quartz granules are hard, resulting in the handling of heavy loads on the secondary classifiers. The quartzite ores are both hard to crush and difficultto grind.The principal sulphide materials are bornite, chalcopyrite, and pyrite, chalcopyrite being the main copper-bearing mineral.The crystallization is coarse in the schisty ores, but it has been shown that even the 200 mesh (Tyler) material contains included sulphide particles. At the present time the sizing of the final tailing averages 80% through 200 mesh.

Jan 1, 1932

By L. G. Austin

INTRODUCTION Autogenous (including semi-autogenous) grinding has probably been the most important single innovation in milling practice for the last twenty years. However, the design of these units has been largely a matter of trial-and-error, since the normal empirical laws for the design of ball mill circuits do not apply with exactitude to autogenous grinding circuits. There have been examples of autogenous mills failing to achieve output or product specifications. It is worthwhile, therefore, to attempt to develop a more detailed and precise set of design laws, using the concepts of specific rates of breakages and daughter fragment distributions (1), and performing mill simulations by computer. This type of approach has been applied to ball and rod milling (2, 3,4,5), but even for these mills it is by no means complete as yet (6), because of the amount of experimental work involved. There has not been a strong incentive for industry to develop new design procedures in ball and rod milling because the prior back-log of experience with these mills makes for easy design by empirical comparsion with existing systems. The new approach has been followed mainly by University groups (7,8,9,10), although experience in Australia (9,11) has shown the advantages of the approach. Stanley (12) has applied the approach to results from a large autogenous mill, and we will use many similar concepts to his work, but extend the concepts to a more

Jan 1, 1977

By George Cole

WHILE many parts of Canada&apos;s pre-Cambrian shield are well served by railway, it is frequently necessary for prospecting purposes to proceed farther into areas in-accessible by rail. To such areas in summer the canoe was at one time the accepted means of travel for the prospector while the dog team was much used in winter. Al-though summer travel was much improved by the development of the outboard motor, the lack of facilities for cheap transporta-tion has been a serious hindrance to the employment of capital in opening up the distant fields. The pre-Cambrian surface of Manitoba, like that of Ontario, is hummocky, with rounded hills and ridges of rock alternating with basinlike depressions and valleys oc-cupied by lakes and rivers or by many low-lying portions covered with muskeg. Routes to the mines have not usually been direct or easy and seasonal vagaries have presented problems in themselves. In summer, water transportation may be the cheapest method for the longer dis-tances but it is not every water route that will satisfy the conditions of loading freight onto a boat or scow and of conveying it without interruption to its destination. By its location, a mine may require a large program of boat transportation in summer over part of its route, to be followed by winter freighting for the remainder. In order to carry on development and produc-

Jan 1, 1940

By Vincent R. Bovino

The future of coal mining is bright - only if we realize and then manage as though we are competing in the world marketplace. Accept it or not, our market is global. We tend to think our problems are caused by the uncontrolled foreign production of coal, and the uncontrolled drop in coal prices. I submit that our problem is not the world pricing structure - part of our problem is our on-site cost structure - our productivity. We are the world&apos;s best at getting out the tons - that is, production. Most mine managers thrive on that. What is in serious doubt is our productivity - our ability to produce tons of coal in a cost effective manner. Please think about the difference: ? Production is tons of coal. ? Producitivity is decreasing the cost per ton of coal. Our future is bright, only if we can increase our productivity by trying different and new ways to manage our businesses and our people. Unlike the easy successes during the 60&apos;s and 70&apos;s, success in the decades ahead will depend on our ability to achieve greater levels of productivity. If mining and other old line smoke stack industries are experiencing difficult times in 1986, three years into an economic recovery, what will happen when the economy cycles downward? Any operation can achieve unlimited productivity by developing the resources within their employees. As an industry, we have harvested the

Jan 1, 1986

By Moxon NT, Torrace AC

The detonation pressure of an explosive is a function of its density and its velocity of detonation (VOD) and relates directly to the degree and manner in which the explosive loads the surrounding rock. The suitabil- ity of an explosive to any particular situation is determined not so much by the total energy released but more by the rate at which it is released. As the science of rock blasting advances it is becoming economically more important to quantify explosive performance, particularly with respect to quality control and fragmentation. As part of a major explosive user, BHP Central Research Laboratories have developed a number of tech- niques to determine the detonation characteristics of explosives. These include a method of continuous velocity of detonation measurement based on the SLIFER principle. This not only enables the VOD of the explo- sive to be determined, but also has the versatility to allow factors such as under priming, slow run up, the effect of water, variable energy load- ing and the velocity of the shock wave in the stemming to be assessed. Multi point VOD systems have also been developed for more routine appli- cations. With a minor modification they can be used to determine the absolute delay of detonators accurately and economically. Direct deto- nation pressure measurement methods have also been developed based on piezoresistive techniques. Future developments include the incorpo- ration of all the above techniques into a single, portable package, allow- ing easy use on the mine site.

Jan 1, 1988

By H. M. Howe

It has seemed to the writer that one important, and indeed sufficient reason, for our slow progress in learning the relation between the chemical composition and the physical properties of cast-iron, has been that the problem has not been attacked properly. It would be well to select the most probable working hypothesis which we can find, and proceed to test that hypothesis by comparison with observed facts, and by making new observations specially designed for such a test. Our first step, then, is to select the most probable working hypothesis ; and to attempt this selection, to state the hypothesis and its immediate corollaries, and to take some first steps toward testing it, is the object of the present paper. Its chief purpose is to bring the hypothesis to the attention of those who are more familiar with the evidence than the writer can pretend to be, and in a better position both to present new evidence and to discuss it. The hypothesis here selected is, that composition governs properties in the case of cast-iron, in the same general way and for the same reasons as in the case of steel, mutatis mutandis. This hypothesis, which of course makes no claim to originality, certainly seems reasonable and probable; its exposition and discussion are made easy by our existing knowledge of the constitution of normal or " carbon " steel; it therefore seems worthy of consideration.

Jan 1, 1902

By John W. Frey

[Minerals, generally of great geological age, are to a very large extent the material basis of what we know as modern civilization. In most of the so-called civilized world the use f minerals has become such a commonplace that it is easy to se sight of their importance. It was the use of minerals, obably more than anything else, that made it possible for e American people to expand from the Atlantic seaboard the Pacific in a little over one hundred years. As the 1 to use the natural wealth at hand constitutes a funda¬ental element in American life, there seems to be justification for the thought that American geography is largely mineral geography. Of all American environmental reactions, the most striking are those which have come about through the use of the metals and the power fuels. If we turn to the ancient industry of agriculture, we find very little that is unique in North America except those developments which have come about through the use of machinery and transportation, both of which are contingent upon the use of minerals. Practically every crop now grown n North America was grown in some part of Europe before merica was discovered. One can point out exceptions to statement but in general it is true. Analysis of the es of North American agriculture shows that the outstand¬ characteristics are: regional specialization (i.e., the Economic Geographer; Chief, Petroleum Section, Minerals Division, u of Foreign and Domestic Commerce.]

Jan 1, 1932

To provide coal operators with an easy-to-use stress control design procedure to minimize coal mine bumps during room-and-pillar retreat mining conducted with available continuous mining machine technology. Approach The goal of this U.S. Bureau of Mines (USBM) re¬search was to facilitate safe and efficient room-and-pillar retreat mining of bump-prone coalbeds by limiting coalbed stress adjacent to expanding gob areas through variation of section layouts. The first step was design of total-extraction pillars and their associated pillar-extraction plans. The second step was development of a coalbed strength model. The third step was development of stress limit design criteria. The fourth and final step was development of a methodology to estimate the magnitude and distribution of development and abutment loads apllied to the pillar line. The linear geometry of unlimited-width sections allowed for the accomplishment of step four with the tributary-area and linear shear-angle concepts. Increasing overburden depths required limited-width sections separated by barrier pillars to control stress within total-extraction panels. The accomplishment of step four with limited-width section designs required prediction of abutment load distributions for rectangular gobs and apportionment of these loads over mixed pillar sizes. A parametric study of the complicated interaction of various combinations of overburden depths, total-extraction panel widths, and abutment pillar widths was conducted with the USBM-developed boundary-element program MULSIM/NL.

Jan 1, 1995

By Sun Henghu

This paper analyses problems associated with cement based technique in metal mines, and provides a new mining technique of packing the tailing sand and water into solidified material. In the new technique, the cementing agent is a solidifying material containing a high percentage of water and tailing sand. The sand and water solidify into the packed body at the same time. The slurry of the packed body varies widely in concentration and suitability for different mining conditions. It consists of two liquid materials, each composed of a cementing agent, tailing sand and water. The thick liquids are transported to the packing place at the same time. Their pumping property is good; they do not solidify or block up the pipe during transportation. At the packing place, the two liquids are evenly mixed. The mixed liquid flattens out well and its solidifying speed is so fast that it solidifies into a packed body within a very short period of time. The compressed strength of the packed body can reach 1.2-5MPa in one day, which satisfies the requirements of different mining conditions. By using the new mining technique, all the tailing sand can be used again in the packed body and it is low in cost and investment. The mechanisation is easy and thus the working efficiency is increased and the use of labour decreased. Contamination problems caused by excess water drainage under the ground are resolved.

Jan 1, 1992