Search Documents

By S. Banisi, A. Ghasemi, S. Zare, F. Ghorbani, E. Nematollahi

"Comminution is the most energy intensive operation which constitutes the major portion of operating and capital costs of the mineral processing plants. Working at the maximum operating capacity of comminution equipment plays a significant role in the efficiency of the circuit. Appropriate design of cone crusher feed box could result in the choked crushing which is known as a vital factor in achieving target performance. In this research, the non-uniform cone crusher feeding at the Sarcheshmeh copper complex was studied and appropriate measures were taken to solve the problem. The problem resulted in non-uniform and high wear rate of crusher liners and high fluctuations of power draw. In recent decades, the discrete element method (DEM) has been applied successfully to study the effect of different factors on the behavior of particles flow. In this work, various designs for feed box were tested using an in-house developed DEM software called KMPCDEM©. The best feed box design obtained from the simulations was selected, constructed and installed in of the cone crushers. The new feed box design resulted in more uniform feed distribution on the distributor plate of crusher indicated by a reduction of the standard deviation of power draw measurements from 13 to 3 kWh. The better control of the crusher, 49% increase in the crusher throughput and finer and narrower product size distribution were the main outcomes of the installation of the new feed box. Furthermore, the wear rate on mantle and liners of crusher not only decreased but it also became uniform.INTRODUCTION Comminution is the most energy intensive operation which constitutes the major portion of operating and capital costs of the mineral processing plants. Reaching the maximum operating capacity in comminution equipment is a key sign of approaching the nominal productivity of the process. Due to the effect of crusher efficiency on the downstream circuit performance, optimization of the crushing circuits has received considerable attention (Herbst, & Potapov, 2004; Quist, & Evertsson, 2010; Li, Huiqi, McDowell, Glenn R, Lowndes and Ian, 2014; Cleary, Sinnott, Morrison, Cummins, & Delaney, 2017). Improving the performance of crushing circuits not only decreases the capital and operating costs but also increases the efficiency of downstream grinding circuits (Jacobson, Janssen, & Urbinatti, 2010). In cone crushers particles can be subjected to two different modes of compressive breakage; single particle breakage (free feeding) and inter-particle breakage (choked feeding). The maximum efficiency of the cone crusher directly depends on the type of feeding arrangement (Operation Manual, 1977). An appropriate feeding must lead to choked feeding the cone crusher. If the rate and method of feeding the crushers are correctly be executed, the maximum efficiency of the crushers could be available (Jacobson et al., 2010)."

Jan 1, 2018

By AIME AIME

FREE competition, long the controlling ideal of domestic trade within the United States, has had the fundamental geographical advantage of functioning in the world's largest area of unrestricted commerce. Goods moved back and forth across state lines, unimpeded by customs, and industrial operations have developed rapidly to meet the expanding needs of a pioneer country richly endowed with natural resources. Fifty years ago, antitrust laws were adopted to protect the competitive private enterprise principle. It became illegal for one person to combine with another to restrain trade or commerce among the several states or with foreign nations. The original legislative measures defining this philosophy were the Sherman Act of 1890 and the Clay- ton Act passed in 1914. The development of Europe and other parts of the world was influenced by different conditions which led to a different theory of trade. Here were many small nations, with limited natural resources and a thin market, and they attempted to protect their national economy by tariff walls. International business arrangements for the purpose of diminishing the ups and downs of the more competitive system --crux of the modern cartel operations-seemed a logical device to stabilize production and guard the interests of both workers and consumers. European governments as well as European industrial interests became convinced that if com- petition could be held in bounds the danger of business depressions and un- employment could be reduced.

Jan 1, 1944

By Walter G. Perkins

T SEEMS almost sheer presumption to attempt' to discuss Russia in its present chaotic political and economic condition, and were it not that at least two certain absolute factors are continuously at work, it would be impossible to' even approach the subject with any degree of intelligence. These are the inborn love of peace of the people and the national character of the cooperative movement. The love of peace inborn in the soul of every Russian, the desire to be left alone and to- live his life among his home village surroundings, is probably one of the two greatest factors that will make the continuance of the present conditions of civil war impossible. One army or the other may sweep up and down the country. but the Russian peasant will: remain in his own village if not literally darken out. This love of peace is evidenced by the fact that there is no country where personal safety is greater than in Russia in normal times. I have traveled in many isolated parts, carrying considerable sums of money and persolial equipment that; in itself, would be a fortune to any peasant, and have never even encountered a condition in which the most wildly imaginative person looking for adventure, 01: trouble, could muster up even a suspicion of fear. This statement applies also to Southern Siberia and Northern Turkestan, which are inhabitated by the nomadic tribes of Khirghese origin.

Jan 1, 1920

By AIME AIME

THE 129th meeting of the American Institute of Mining and Metallurgical Engineers convened at New York City, in the Engineering Societies Building, Feb. 18-20, 1924. On February 21 an excursion was made to the Bethlehem Steel Co., at Bethlehem, where about 200 members and guests were splendidly entertained. An illustrated description of the Bethlehem Plant will be published next month. The meeting and excursion were largely attended; the registration at New York totalled 1276 versus 1201 in 1923. William Kelly, long identified with the iron-mining industry of the Lake Superior district, was elected President of the A. I. M. E. for the coming year, at ,the annual business meeting, Feb. 19, succeeding E. P. Mathewson. The following Directors were also elected (the date signifies year of termination of office; the final figure indicates the "District" the Director represents).

Jan 1, 1924

By E. L. BROKENSHIRE

FLUORSPAR, a little known non-metallic mineral, referred to technically as fluorite, chemically as calcium fluoride, is a compound of calcium and fluorine in the ratio of one molecule of calcium to two of fluorine. By weight it is composed of 51.3 per cent of calcium and 48.7 per cent of fluorine. Its specific gravity is 3.2. It is brittle, has a hardness of four and can be easily scratched with a knife. It weighs about 200 Ib. per cubic foot and has a melting point of 1650" F. The color of fluorspar ranges from pure white and opaque white, according to its purity, to various hues of yellow, green, pink, lavender, blue and brown, to bluish black. Although the lumps have color, when ground the fluorspar becomes pure white. The reason for this is because the mineral usually carries no fixed pigment, the color being produced by the re- fraction of light rays within the crystal structure and small quantities of organic matter which readily oxidizes. It crystallizes in the isometric system with perfect octahedral cleavages.

Jan 1, 1929

By Aruna Mangalpady, Sandeep Kumar Jeripotula, Govinda Raj Mandela

Injuries due to work-related musculoskeletal disorders (WMSDs) are not uncommon in heavy industry like mining. Researchers acknowledged that occupational exposure to ergonomic risk factors is the chief causative factor in the development ofWMSDs. The aim of this study was to perform an ergonomic assessment of musculoskeletal disorders among surface mine workers in India. Standardized Nordic Questionnaire was used to collect subjective response from 500 workers. A stratified random sampling method according to surface mining work activity type was used to obtain the sample. Data was collected by means of a structured questionnaire, and the Statistical Package for Social Sciences (SPSS) was used to analyze data using descriptive and inferential statistical methods. A response rate of 85% was obtained out of 500 targeted groups. TheWMSDs prevalence for the 12-month period was estimated to be 44.23%. The mean and standard deviation of workers’ age were 41.31and 8.927, respectively. The study has shown that the operators of dumpers, dozers, and graders along with electricians were found to be the most susceptible to developWMSD problems. Among the most affected body parts, back disorder reported the highest. Further, it was found that working with static posture over the longer duration has a significant association with the lower back disorder (with p = 0.020) and bouncing and jarring has also significantly associated with the lower back disorder (with p = 0.023). Similarly, a significant association was found between repetitive work and neck pain (with p = 0.016). The study depicted a significant association between ergonomic hazards and WMSDs, like working with prolonged static posture, bouncing and jarring, and repetitive work.

Mar 13, 2020

By Max W. Ball

Our ever-increasing use of minerals has been the outstanding fact in our American economic development. The rise in our standard of living in the past century is without equal in human history. Nowhere in time or place has the man who works lived so well, or the man who cannot work been so well cared for. We live in a new world, even the poorest of us, that our forebears of 1849 could not have dreamed. That new world has come mainly from our use of minerals. Our per capita use of nonmineral products has grown too, but by only a modest amount. Food consumption per person has grown about 15 per cent in the past fifty years; lumber use per person ,has fallen 56 per cent and that of wood for fuel 65 per cent. Of all the products of field and forest, our use, per capita, may have increased by one fifth during the present century. In contrast, our per capita use of minerals has multiplied several times. Each of us uses 2% times as much steel and 16% times as much petroleum as our fathers used in 1900. In less than half a century our per capita consumption of all minerals has probably risen by 200 to 250 'per cent. Man once built with wood; today he builds mainly with brick and stone and steel. Once he traveled by the power of hay and oats; today he travels by the power of coal and oil. Rubber made from minerals is already better for some uses than rubber tapped from trees; before long it will be better for most and perhaps all uses. Even our ladies' graceful legs are clad in mineral fiber, where once animal or vegetable fiber would have covered them. Our high standard of living is a product of the machine.. The machine is made of minerals. The machine is driven by minerals. The machine age is a mineral age.

Jan 1, 1949

By Albert F. J. Bordeaux

(Cleveland Meeting, October, 1912.) THE immediate vicinity of the sea-shore, affording special facility for the exportation of ores, makes it possible to work certain mines in the Vladivostok district, which, in more remote places of Siberia, would remain unproductive. Outside of the city of Vladivostok the population is small and the country is very little prospected. Additional discoveries of valuable deposits like the large body of calamine which has recently been opened in the neighborhood of earlier worked lead-silver ores, in the Tetiuhe valley, are still in the field of possibilities. For many years gold alone was produced, in part from the coastal rivers and in part from a quartz-vein on Askold island near Vladivostok. But the production is diminishing, and prospectors are looking for other rivers in the interior, such as the tributaries of the Ussuri. These rivers are now more accessible than formerly, due to the slow but gradual development, of colonization by the Russian peasants. The few natives of the country, called Orodjones, are of the Chinese race. They resemble the North American Indian and are hardy fur-hunters. They have given some attention to placers and have already shown good specimens of gold-dust from the rivers Iman, Bikin, Noto, etc. Coal-mining was begun in the Vladivostok region more than 20 years ago, but in a somewhat irregular way. The industry is not as yet important and the best coal-seams are badly prospected, or ire even neglected. Copper, lead, and iron exist in several places. The amounts give some encouragement to the anticipation that the discoveries will give rise to important metallurgical works. I here present a review of the various deposits, based upon such safe information as is in hand, when I have not drawn upon my personal observations. Fig. 1 is a snap of Eastern Siberia, showing the mineral deposits.

Oct 1, 1912

By Liao Jianfeng

The Baosteel Zhanjiang 5,050m3 blast furnaces have been built with highly independent integration and innovation technologies and represented the state of the art of the world’s huge BFs. The proper of BF1 and BF2 is designed with long-campaign technology; both BFs share the same set of stockhouse, water and PCI systems; the BCQS serial-hopper no-bell top, TRT and blower are all local equipment as applied; four top-combustion stoves systems are matched; the BFG is cleaned by fully dry process; and the automation control system for the main process is self integrated. The BFs have been started up and performing with sound indicators. Their smooth proceedings symbolize China’s huge blast furnace ironmaking technology ascending a new high.

Oct 30, 2017

By Dong-dong Liu, Jian-ping Niu, Qi Liu, Shu-sen Cheng

A numerical model was developed to simulate the three-dimensional heat transfer in the belly and lower shaft region of the blast furnace wall consisting of copper steel composite stave, packing and shell. The temperature distribution of copper steel composite stave without the slag layer or refractory lining was investigated and then compared with the copper stave. The results showed that copper steel composite stave can satisfy the requirement of overheatingfree and had an analogous heat transfer behavior as copper stave but more stable cooling intensity. This model had been validated by the good agreement between the computed and measured temperature in the thermal test.

Jan 1, 2015

By J. Kemeny, J. Lyons-Baral

"Point cloud technology is now an indispensable tool in geological and geotechnical data collection, interpretation and analysis. Open pit and underground mines of all sizes are regularly collecting point cloud data as Laser Scanning (LiDAR) and Photogrammetry surveying devices have finally become affordable and the workflows fast and efficient. Past challenges of large data processing and manipulation are gone with recent technological advancements in computer hardware and software. These innovations reduce file sizes, ease rendering requirements and allow for the implementation of real-time 3D viewers and surface meshing tools. With its ability to remotely (safely), rapidly and accurately extract large quantities of georeferenced and 3D-oriented data, point cloud technology provides numerous applications to the geomechanical field. The list of uses is continuously growing, so this paper specifically focuses on digital outcrop modeling and digital terrain engineering. INTRODUCTION Point Clouds The high-resolution and increasing availability of point cloud technology is rapidly improving open pit and underground mines’ investigation, interpretation and characterization of site geology and rock mass properties (Kemeny et al., 2015; Lyons-Baral, 2012). LiDAR and photogrammetry are common remote sensing methods employed to measure the coordinates of surfaces in three dimensions (3D), providing the X, Y and Z locations, and typically the reflective intensity and/or the visible three-band color of each point (Figure 1). LiDAR uses either a time-of-flight or phase-shift measurement of a laser beam reflected off targeted surfaces and received back into the device. Photogrammetry generates point clouds by merging multiple overlapping photographs and uses stereographic plotting to define the locations of object points in 3-D space. These methods can be deployed from airplanes, unpiloted aerial systems (UAS or drones), tripods, land vehicles, and even in a mobile backpack shown in Figure 2. RADAR, Total Station-Prism and other remote sensing systems also offer very precise “point clouds”, but this paper does not address these due to their higher cost and lower versatility and mobility. Technology In the past few years point cloud acquisition device prices have dropped significantly, devices have become lighter, smaller and easier to operate, and processing and utilizing the data has also become faster and easier. Device size improvements include mobile backpacks (Figure 2) and handheld mobile LiDAR (CISRO, 2014), allowing mobile scanning in tight spaces both above and below ground or inside and outside of man-made structures. Airborne data acquisition options have expanded dramatically with the spread of UAS technology as seen in Figure 3 (Hexagon Geosystems, 2015). Once UAS usage regulations are sorted out, these versatile machines will be everywhere, offering high resolution coordinate scans, imagery and other remote sensing. While backpacks and handhelds allow access to tight quarters, UAS permit rapid data capture from narrow to broad areas with multiple perspectives reducing data “shadows.”"

Jan 1, 2016

By E A. Agorhom, M Beyuo, C Owusu, I Quaicoe

Understanding the mineralogy and liberation of gold particles in an ore is key to the development and optimisation of gold processing operations, being cyanidation or gravity separation. This can be achieved through basic historic geological information, gold deportment studies, chemical speciation and metallurgical test works. The present study assessed the nature of the occurrence of gold particles (mineralogical composition, liberation, associations and surface chemistry) and its effect on the process route (cyanidation and gravity separation) of a typical paleo placer gold ore deposit within the Tarkwaian Rock system. The investigative approach used involved chemical assay, quantitative X-ray diffraction (QXRD) and quantitative evaluation of minerals using scanning electron microscopy (QEMSCAN). The ore samples (A, B, C, D, E, F) used were obtained from six active pits of a gold mine working on this orebody. The results of the mineralogical analysis revealed that the ore is highly oxidised and comprised quartz (>80 per cent) and Muscovite mica (>6 per cent) as the major mineral phases in all the samples. Trace amounts of hematite, kaolinite and todorokite were also identified in all the samples. The chemical analysis showed presence of gold (Au) in all the samples with samples B (3.62 g/t) and C (3.96 g/t) containing the highest concentrations. Trace amounts of copper (Cu), iron (Fe), sulfur (S), aluminium (Al), arsenic (As) were also detected in all the ores. The QEMSCAN mineralogical liberation and gold association results revealed that the gold grains were relatively coarser in all samples (P80 > 80 µm Au in size) except F (P80 < 32 µm Au in size). Gold grains were highly liberated especially in sample B with the majority of the locked gold grains forming complex associations. All the samples responded well to cyanidation and gravity separation except samples C and F, respectively.

Aug 24, 2022

By Guilherme L. M. G. Carvalho, Zachary T. Fleming

In a world of 2-dimensional design documents, envisioning and understanding 3-dimensional interferences for complex foundation construction scenarios can be challenging. Videos and computer models serve as 3-dimensional spatial aids but have drawbacks related to a fixed perspective. Augmented and virtual reality (AR/VR) provide new tools to communicate design challenges and improve construction planning. This paper provides a practical look at the basics of AR/VR systems and the tools available to the foundation design and construction industry by giving a high-level example of the technologies’ use in the design and delivery phases of a complex micropile installation project for the remediation of a dam foundation. Using these technologies, GEI was able to design and deliver a complex foundation remediation solution. AR/VR benefited regulators, and the client, to help understand the design concept, construction sequencing, and approach to overcoming installation challenges. Due to its user-friendly nature and less rigorous programming and hardware requirements, AR proved to be more useful than VR for this scenario. AR/VR will likely not replace videos and computer models; however, it can be a useful 3-dimensional visualization aid that complements the project delivery process and offers benefits that traditional methods cannot. INTRODUCTION Augmented and virtual reality is a promising and rapidly developing technology within the engineering and construction world. Like any rapidly developing new technology, the language describing it can be confusing and dynamic. To eliminate the confusion some definitions must be made. AR/ VR definitions The definitions of virtual reality (VR) and augmented reality (AR) for the purposes of this paper are as follows: VR is a computer-generated immersive environment that the user experiences within a digital 3- dimensional space (Satava, 1993)AR is a composite view created by superimposing digital objects into the user’s real-world view (Azuma, 1997). Often, VR is used in an office environment and allows the user to “visit” the digital site to review site planning, construction sequences, and interference geometry. AR can be utilized in both the office and onsite environments. Like VR, the in-office application for AR is commonly site planning. AR also can be utilized in the field for applications such as seeing through the ground to locate known existing obstructions like utilities, gas tanks, etc.

Jan 1, 2019

By Felix Schmid

ABSTRACT Lateritic bauxite deposits of economic size and grade in Sierra Leone occur on granulites of the Kasila series. The high grade trihydrate ores of Mokanji are exploited by SIEROMCO since 1964. Remaining reserves are small (2 million tons) and operation moved over to the Gondama deposits of similar grade. Port Loko bauxite reserves are estimated at 100 million tons and are of relatively lower grade. It is planned to treat this ore locally into alumina. Guinea&apos;s bauxite reserves exceed those of any other nation. They occur as hard lateritic bauxite covers on plateaus of the Pre-Cambrian sedimentary formations and on doleritic intrusions. The genesis is still controversial. The Sangaredi mine has produced high grade ore for the last 10 years. Friguia exploits a relatively lower grade ore at a rate of about 2 million tpy to be treated in their local alumina plant. Kindia ore is mined at a yearly rate of 2,5 million tons since 1974. Untouched reserves at Ayékoyé and Tougué/Dabola are estimated at 6,000 million tons.

Jan 1, 1984

By Gibson J.

Further discussion at the North of England Institute of Mining and Mechanical Engineers' general meeting held in Newcastle-upon-Tyne, 3rd June 1916, on the paper published in Trans. I.Min.E., vol.LI, 1916, p.72-84, included a written contribution by Parfitt I.C. and the author's written replies to this and previous discussion

Dec 1, 1916

By P A. Lang, J G. Ayotte, R W. Humphries

Atomic Energy of Canada Limited (AECL) has the responsibility for research, and development of technologies, for the safe and permanent disposal of Canada's nuclear fuel wastes. As part of this comprehensive program, AECL is constructing an Underground Research Laboratory (URL) near Lac du Bonnet, Manitoba, to evaluate aspects of the concept of waste disposal deep in stable geological formations. No nuclear wastes will be used in the URL program.

Jan 1, 1986

By Takaaki Shibata

The Tamano Refinery has developed two new processes for removing the impurities, arsenic, antimony, and bismuth from an electrolyte. The first process involves bleeding the surface electrolyte in the electro-refining cells. The copper concentration level in the outermost layer is lower than that in any of the other layers, while the impurity levels are almost the same in all layers. Bleeding the surface electrolyte increases the amount of impurities removed in the liberator by approximately 20%. The second process involves adsorbing antimony and bismuth from the electrolyte by means of chelating resin. As the electrolyte passes through the packed column of chelating resin, antimony and bismuth are selectively adsorbed. They are then desorbed by means of hydrochloric acid, and then recovered in the form of a highly concentrated antimony chloride solution by means of evaporation. This process almost doubles the capacity for removing antimony from an electrolyte.

Jan 1, 1987

By D Giles, A C. Bailey

In the first 20 years of the 21st century, just over 20 per cent of Australian mineral exploration expenditure was dedicated to iron ore, totalling >A$8 billion and >30 million metres of drilling (Australian Bureau of Statistics, 2021). Improvements in the cost, efficiency, safety, reliability and data quality of drilling have the potential to deliver significant productivity improvements, increasing the probability of discovery and reducing the time from discovery to mining. Currently in its third year of research, Mineral Exploration Cooperative Research Centre (MinEx CRC) is focused on a new set of exploration tools and new ways to deploy those tools which recognise the fundamental importance of collecting quantity and quality data from the subsurface, to enable exploration success for all minerals, including iron ore. MinEx CRC is focused on developing more productive, safer and environmentally friendly drilling methods to discover and drill-out deposits. This includes pioneering work on Coil Tube (CT) drilling technology and innovations in Diamond and Reverse Circulation (RC) drilling techniques aimed at improved drilling optimisation and automation. In parallel, MinEx is developing new technologies for collecting data whilst drilling. This is being undertaken in four separate industry-led projects utilising geophysical, seismic, downhole analytical and 3-dimensional (3D) modelling improvements. A National Drilling Initiative (NDI) is also underway, with two drilling programs completed in 2020. The NDI is a world-first collaboration of Geological Surveys, researchers and industry, which undertakes drilling in under-explored areas of potential mineral wealth in Australia and provides a test-bed for new mineral exploration technologies.

Nov 8, 2021

By Sean Hunter

Artificial Intelligence has a long history but is currently coming strongly into focus with new advancements. This leads to questions many people are asking: what exactly is AI, how can it be used effectively in mining operations, and what foundation is required to make AI implementations successful? In mining, many AI applications exist, from drill pattern optimization to predictive maintenance. However, many implementations struggle due to data integration challenges. Mining operations generate large amounts of data from many sources, such as fleet management systems, drill sensors, process control systems, and laboratory results. Unfortunately, this data often exists in silos where it’s difficult to get it out, making AI applications unable to leverage it. Worse still, tools that use AI don’t always provide their data back to the system, creating even further data silos. All these problems make it hard to take advantage of the data at the mine, slowing down and reducing the effectiveness of AI. This paper presents a comprehensive approach to organizing mining data using an AI-ready knowledge graph system. We will first explore the evolution of AI in mining, from early expert systems to modern machine learning applications. Then, we will detail how a knowledge graph can integrate business context, operational data, and AI models into a cohesive system that enables more effective AI implementations across mining operations. The proposed method has been developed considering both the unique data challenges faced by the mining industry, while also considering best practices learned from the AI field at large. By following this approach, it’s possible to better utilize existing data, getting higher quality and more complete results faster, and in a way that’s reusable and composable.

Feb 1, 2025

By Ronald Damen, Dion Denes

"Friction fatigue is the loss of soil-pile friction around the shaft area of the pile. It has been observed during impact driving of piles, and has been modelled to a limited degree using physical scale models. This paper proposes the use of high strain dynamic pile testing to assess and quantify friction fatigue in impact driven piles. The method is applied to two case studies: one on a project off the north-west coast of Australia and one on a South Pacific Island. On both sites calcareous sand layers are present. Pile Driving Analyzer (PDA) monitoring has been conducted during impact driving of steel piles, which allowed for assessment of shaft resistance development both with depth and with progressive driving, by use of wave equation signal matching. Lessons are drawn from the case studies to improve future observations.INTRODUCTIONFriction fatigue is the loss of soil-pile friction around the shaft area of the pile, under cyclic loading or during pile driving. The phenomenon has been frequently observed in some non-silica sands, such as pumice sands and calcareous sands and has been the subject of academic study.The occurrence of friction fatigue impacts the driving behaviour of piles and the shaft friction component of the ultimate geotechnical strength (Rd,ug). If potential friction fatigue is not recognised in the design phase of a project, required pile toe levels can be significantly underestimated. This could lead to extra cost and delays, or, if no adequate pile verification is conducted, to geotechnical failure or underperformance of piles. This is especially true in remote locations, such as Pacific islands, where calcareous material is often present.A better understanding of the phenomenon would aid both pile design and driveability assessment. This paper proposes the use of high strain dynamic pile testing to assess and quantify the effect of friction fatigue from impact driving. Two case studies are presented in which high strain dynamic testing has been conducted on driven piles in calcareous sands to illustrate the method.BACKGROUNDFriction fatigueThe geotechnical strength of piles is composed of the resistance to static loading by the base of the pile and the shear resistance between the shaft of the pile and the adjacent soil. The latter is often referred to as the shaft resistance or shaft friction.During impact pile driving, a decrease in shaft resistance is often observed. Although this phenomenon is also observed during vibratory pile installation, this paper deals predominantly with impact driving. This decrease in material strength from the tip of the pile influences the shaft resistance and may be either temporary or permanent. Temporary reduction in shaft resistance is common in cohesive soils and is thought to be caused by excess pore water pressure, which has insufficient time to dissipate. This phenomenon, commonly referred to as set up, is observed to a significantly lesser extent in non-cohesive materials such as clean sands (Rausche et al., 2004)."

Jan 1, 1900