Search Documents

By Victor R. Spironello

The Bureau of Mines has studied slags associated with ferrous melting, to evaluate substitutes for the auxiliary flux mineral, fluorspar. A waste material recovered from alumina reduction cells, "used potlining," was tested in an 18-in-ID basic-lined cupola and in a 1/4-ton, pilot-scale, basic oxygen furnace (BOF). One potlining fraction, No. 1 cut, is a carbonaceous (graphitic) material and represents the bulk of the entire cell lining. The other fraction, No. 2 cut, is a refractory backup. These materials contain significant quantities of fluorine and other elements fn various compounds. The potlining fractions were blended in ratios believed representative of available materials. Both lump and pelletized forms provided extremely fluid slag. No adverse effects were found on furnace performance, chemistry or strength of the metals produced, or the environment. Fluorine recovery in the slag and fluorine losses to the scrubber water and solids were about the same as when fluorspar was used. There was apparently no lining loss from the cupola, but there was lining attack in the BOF. Since the fluidizing ability of potlining is due in part to sodium and other elements such as aluminum and silicon, less fluorine is needed in the slags when potlining is used.

Jan 1, 1983

By A. George Stern

[In the examination of bentonitic clay suspensions used for oil-well drilling fluids3/ (and for other purposes, such as a core binder for foundry sand) it is important to have comparative tests for evaluating them. A satisfactory clay for these and other purposes should have the property of forming what is commonly called a "gel," but the measurement of this property has been a real problem. To date the solution has not been satisfactory, and some of the difficulties are considered in, this, paper, which describes a simple form of instrument (identified as an eykometer) for measuring the yield point under hydrostatic conditions of non-Newtonian clay suspensions, including those muds that are thixotropic. An oil-well drilling mud serves several functions, many of which depend on the "gel" characteristics of the mud. Among the more important functions are: (a) To plaster the sides of the hole to prevent caving of the walls; (b) to prevent the loss of the circulating fluid out of the hole by seepage; (c) to carry sand and cuttings out of the hole to the surface as they are formed by the rotary drill; and (d) when circulation of the fluid stops for shut-down or other unavoidable cause, to hold the cuttings in suspension by the setting up of the gel, thereby avoiding the difficulties that result when these cuttings are allowed to fall through the fluid and pack at the bottom of the hole.]

Jan 1, 1940

By Walter B. Lenhart

This paper is one of a series on milling methods and costs being. published by the Bureau of Mines. The milling practices and special problems relating to grinding, tailings disposal, and choice of a treatment process at the Cardinal mill are discussed. The property of the Cardinal Gold Mining Co. is about 18 miles southwest of the town of Bishop, Inyo County, Calif., at an altitude of approximately 8,500 feet. The camp has been designated Bishop Creek by the postal authorities. The property comprises 33 mining claims, including fractions and millsite in sections 19, 20, 29, and 30, T. 8 S., R. 31 E. These claims are located in a general way along the strike of a band of quartzite.

Jan 1, 1938

By W. D. Kaiser

Recent legislation and expected future legislation is aimed at reducing the dust levels developed in underground coal mines. Several techniques for reducing dust levels are being evaluated. One of these is the modification of cutting parameters such as feed rates, cutting speeds, and pick configurations in order to reduce the amount of dust generated. In order to evaluate the feasibility of modifying cutting parameters to reduce dust, the Bureau of Mines commissioned Battelle to construct a small scale mining machine which could be used for evaluating the effects of those changes in cutting parameters. Specific features of this machine were that it should be highly instrumented to measure various cutting parameters, should have a wide range of feed and speed controls, and it should be possible to vary the pick configurations and geometries on the machine. In addition, it was desired that this machine should have cutting capabilities which greatly exceed present coal mining practice and also that the unit should be small enough and portable enough that it could be taken into and out of operating coal mines with a minimum of interference with the normal coal mine operations. The first step in constructing a machine to meet these requirements was to determine the cutting forces and approximate sizes of components which would be required to cut at the speeds and feeds specified by the Bureau of Mines. Initial calculations using; published data on cutting forces indicated that cutting forces in the neighborhood of 5,000 lbs and power levels of approximately 30 horsepower would be adequate for the application. However, further data developed during the course of the project indicated that when low efficiency picks are used, cutting forces and powers can be two to three times as high as these initially estimated values. After several design iterations, a design was chosen in which the cutting head was driven by four hydraulic motors which were part of a hydrostatic transmission which, in turn,

Jan 1, 1973

By George A. Savanick

An experimental hydraulic jetting device intended to operate in a 16-in-diam borehole was designed, fabricated, and used to cut coal and simulated coal samples. This device consisted of two 0.107-in-diam nozzles that rotated in a plane perpendicuIar to a 50-inch length of high-pressure tubing. Experi¬ments were also conducted with stationary jets issuing from a single 0.142-in-diam nozzle. Numerous experiments were performed using systematic variations of jet parameters coupled with assessments of cutting rates. These Bureau of Mines tests showed that when operated at 4,000 psi pressure and a 40-gpm flow rate (1) the device can fragment coal up to a distance of 8 feet from the nozzle, (2) 4,000-psi jets cut more effectively than lower pressure jets with the same nozzle diameter, (3) stationary jets do not cut as effectively as moving jets, (4) interkerf breaking occurs when the kerf spacing is less than 2 inches, and (5) if the kerfs are spaced <1/2 inch, the jet is deflected and thereby reduces cutting effectiveness.

Jan 1, 1975

By J. R. Thoenen

In the summer of 1937 the authors began a series of time studies of the various processes employed in&apos; the production of crashed stone. These studies, made at quarries situated in the eastern and southeastern parts of the United States, have not been completed, but to make results available to the industry as early as possible, it was decided to publish summarizes of the studies made to January 1, 1939, as a series of progress reports. The first of these dealt with power-shovel loading and was issued as Report of Investigations 3461 in September 1939. The second, issued in September 1939 as Report of Investigations 3467, dealt with quarry haulage. The present report discusses analyses of time studies of primary drilling a t the same group of quarries. OBJECT OF STUDY Pressure of business problems frequently requires the entire attention of quarry management, and in consequence internal plant economies often are neglected. Also, operating officials absorbed in their local problems are prone to overlook possible economies that would attract attention immediately were they critically examining another plant. The authors felt that technical studies at a number of plants, made by impartial engineers, might disclose opportunities to reduce costs or improve efficiency in internal plant processes.

Jan 1, 1940

By R. J. Leary

Iron and steel scrap has accounted for 45 to 50 percent of the metallics used by the steel industry. In an electric furnace which utilizes a 100-percent cold charge consisting of about 99 percent scrap and 1 percent pig iron, sensible heat from molten pig iron is not present as it is when hot metal is charged to open hearths and converters. A study of means for more efficient utilization of iron and steel scrap in steelmaking indicated that the time and fuel requirements to melt scrap were important cost factors, particularly in arc-furnace steelmaking. A process to preheat scrap economically prior to charging into the arc furnace has been developed, utilizing efficiently the heat from combustion of fossil fuels as a substitute for electric-arc heating in the initial stage of arc-furnace steelmaking. Scrap is loaded into a portable vertical cylindrical furnace body that is open at the top and has a perforated dropout door at the bottom. In the heating operation, the furnace body containing scrap is placed upon a hollow base connected to a flue, and then the burner and combustion-chamber unit is lowered on top of the furnace body. The stream of hot-combustion products flows down through the bed of scrap imparting heat to it, and the cooled gases exhaust through the flue. After the heating operation the furnace body containing hot scrap is transported to the arc furnace for charging. Thus, the furnace body serves as a charging bucket for top-charged arc furnaces, enabling this preheating process to be integrated into existing material-handling patterns in many arc-furnace plants.

Jan 1, 1961

By M. Bwalya, L. Mabokela, L. C. Woollacott

This paper presents a study on the ability of the King stratification modelto describe density stratification patterns that are achieved under idealizedconditions. Tests were conducted in a batch jig using artificial particles inseven density classes. All particles in a density class had essentially thesame density, size, and shape. Tests were conducted for particle systemsinvolving from two to seven components. Good agreement was obtainedbetween measured and modelled data to an extent that gave strongendorsement of the mathematical appropriateness of the core equation inthe King model. Somewhat ambiguous results were found with regard toclaims about the independencies of the single experimentally-determinedparameter required by the model.

Jan 1, 2015

By Albert L. Toenges

A phase in strip mining of bituminous coal is the overturning of the surface of the land. The purpose of this report is to acquaint the operators and others interested in stripping with the work that has been done in certain States to reclaim the surface of land from which the coal has been removed by this method of raining. The preparation of this manuscript follows an extensive study of the subject in the field in the course of which a large number of strip mines were visited. ACKNOWLEDGMENT The information used in the report was obtained through the courtesy and cooperation of the operators of the mines visited, State officials and educational institutions, and others interested in the subject.

Jan 1, 1939

By B. J. Moore

This Bureau of Mines publication estimates that U.S. helium resources as of January 1977 were 710 billion cubic feet. These resources are broken down into four classifications, as follows: Helium in measured natural gas resources and in storage, 201 billion cubic feet; helium in indicated natural gas resources, 150 billion cubic feet; helium in hypothetical natural gas resources, 175 billion cubic feet; and helium in speculative natural gas resources, 184 billion cubic feet.2 Most of the helium in natural gas is presently dissipated as natural gas is consumed as fuel and for other purposes. Helium resources of the United States may also be divided into three other categories: (1) Depleting and undiscovered natural gas resources, 589 billion cubic feet; (2) nondepleting natural gas, 83 billion cubic feet; and (3) storage, 38 billion cubic feet, of which 37 billion cubic feet is federally owned and 1 billion cubic feet is privately owned. The United States does not have any significant leasehold rights in the depleting fuel gas resources. However, through the Department of the Interior, it does have leasehold rights to about 70 percent of the helium found in nondepleting natural gas, and it owns over 90 percent of the helium in storage.

Jan 1, 1979

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Also included are tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1988

By G. L. Oldright

The data presented in this paper were collected at the smelter of the Consolidated Mining & Smelting Co. of Canada, Ltd., Trail (Tadanac), British Columbia. Many thanks are due to S. G. Blaylock, vice president and general manager, James Buchanan, smelter superintendent, and George Murray, assistant smelter superintendent, for their broad general policy in permitting these data to be taken and published. life are also grateful for the help given by the staff members stated in Paper XI, Report of Investigations Acknowledgment is given several excerpts from experiments by F. E. Lee, head of the research staff. INTRODUCTION The past reputation of zinc as an ingredient in lead blast furnace slags has been bad. Zinc is thought of as a cause of accretions in the shaft of the blast furnace, of hot tops, of the formation of "zinc mush" in the crucible and forehearth, of lead-rich slags, of viscous slags, and. of low capacity in smelting.

Jan 1, 1934

By L. K. Weaver

The Bureau of Mines has started an engineering study of oil recovery by miscible-phase displacement. As a preliminary part of the investigation a literature and patent study was made to prevent duplication of work already done, to become acquainted with those actively engaged in research of this type, and to learn where the recovery method has been attempted. This bibliography gives results of this study. The bibliography includes 254 references to U.S. and foreign patents and published literature relating to miscible-phase displacement processes of oil recovery. It is divided into the following sections: (1) U.S. patents, (2) foreign patents, (3) literature references, (4) author index, and (5) publication and source reference. The patents and literature references are listed alphabetically by author by intervals of years. References to February 1963 are included.

Jan 1, 1963

By L. K. Weaver

The Bureau of Mines has started an engineering study of oil recovery by miscible-phase displacement. As a preliminary part of the investigation a literature and patent study was made to prevent duplication of work already done, to become acquainted with those actively engaged in research of this type, and to learn where the recovery method has been attempted. This bibliography gives results of this study. The bibliography includes 254 references to U.S. and foreign patents and published literature relating to miscible-phase displacement processes of oil recovery. It is divided into the following sections: (1) U.S. patents, (2) foreign patents, (3) literature references, (4) author index, and (5) publication and source reference. The patents and literature references are listed alphabetically by author by intervals of years. References to February 1963 are included.

Jan 1, 1963

By A. George Stern

In the examination of bentonitic clay suspensions used for oil-well drilling fluids3/ (and for other purposes, such as a core binder for foundry sand) it is important to have comparative tests for evaluating them. A satisfactory clay for these and other purposes should &apos;rave the property of forming what is commonly called a "gel," but the measurement of this property has been a real problem. To date the solution has not been satisfactory, and some of the difficulties are considered in, this, paper, which describes a simple form of instrument (identified as an eykometer) for measuring the yield point under hydrostatic conditions of non-Newtonian clay suspensions, including those muds that are thixotropic. An oil-well drilling mud serves several functions, many of which depend on the "gel" characteristics of the mud. Among the more important functions are: (a) To plaster the sides of the hole to prevent caving of the walls; (b) to prevent the loss of the circulating fluid out of the hole by seepage; (c) to carry sand and cuttings out of the hole to the surface as they are formed by the rotary drill; and (d) when circulation of the fluid stops for shut-down or other unavoidable cause, to hold the cuttings in suspension by the setting up of the gel, thereby avoiding the difficulties that result when these cuttings are allowed to fall through the fluid and pack at the bottom of the hole.

Jan 1, 1940

By L. W. Higley

It is estimated that well over 20 million lb of chromium and 8 million lb of nickel, plus other metal values, are diverted annually to furnace dusts, mill scale, and contaminated swarfs in the domestic stainless and other specialty steelmaking industry. Little inroad has been made toward the in-plant recycling of these wastes to reclaim the metal values. The Bureau of Mines has devised a process for recovering about 90 pct of the chromium and molybdenum and well over 90 pct of the nickel and iron from stainless steelmaking furnace dusts, swarf, and mill scale. Other metals such as manganese are also recovered. Initial laboratory results were confirmed and expanded to include a wide variation of stainless steelmaking waste mixtures. Later experiments have included specialty steelmaking wastes other than from stainless steelmaking. Significantly, the ease of technology transfer has been demonstrated by a number of industrial-sized (19-ton) commercial electric furnace heats, in which the pelletized wastes represented some 10 to 20 pct of the furnace charge, replacing part of the normal scrap charge. Results of these successful large-scale trials are presented. Some information is also presented on incorporation into the pellets of chromium-bearing particulate wastes originating from other than steelmaking production. Cost evaluation indicates the process is economically attractive.

Jan 1, 1982

By W. L. Falke

The Bureau of Mines has developed a system that permits the "soft" soldering of aluminum and aluminum alloys with standard tin-lead solders. The method employs application of a thin nickel-copper-alloy coating to the substrate, which enables the tin-lead solders to wet readily and spread over the areas to be joined. With conventional technology, aluminum and aluminum alloys are extremely difficult to solder because tenacious surface oxide films prevent wetting. With the Bureau-developed method, the aluminum substrate is mechanically or chemically cleaned to facilitate bonding to a minute layer of zinc that is subsequently applied with an electroless zincate solution. The nickel-copper-alloy (30 to 70 pct Ni) coating is then applied electrolytically over the zinc, using immersion cell or brush-coating techniques. Development of acetate electrolytes has permitted deposition of the proper alloy coatings. The coated areas can then be readily joined with conventional tin-lead solders and fluxes. The joints so formed are ductile, strong, and relatively corrosion resistant, and exhibit strengths equivalent to those formed on copper and brass when the same solders and fluxes are used. The method has also been employed to soft-solder magnesium alloys.

Jan 1, 1983

By H. R. Appell

The Bureau of Mines is experimentally converting cellulose, the chief constituent of organic solid waste, to a low-sulfur oil, All types of cellulosic wastes, including urban refuse, agricultural wastes, sewage sludge, wood, lignin, and bovine manure, have been converted to oil by reaction with carbon monoxide and water at temperatures of 350° to 400° C and pressures near 4,000 psig, and in the presence of various catalysts and solvents, Cellulose conversions of 90 percent and better (corresponding to oil yields of 40 to 50 percent) have been obtained. A continuous reactor for use at maximum conditions up to 500° C and 5,000 psig has been operated successfully, Using sucrose as a feedstock, operation in this system has permitted a simplified and preliminary chemical study of the conversion process. Oil yields of over 30 percent have been obtained with this unit.

Jan 1, 1971

By D. E. Kirby

The electrochemical reduction of AlC13 was investigated as a process for the production of aluminum. An externally heated, single-compartment cell with a rammed refractory lining was used with molten KCl-NaCl-AlC13 electrolyte. Aluminum was deposited qt 700° to 760° C with a current of 100 to 200 amperes on a molten aluminum cathode. Chlorine was evolved at a graphite anode and collected and measured to provide a quantitative evaluation of the AlC13 reduction. Aluminum was removed from the cell by siphoning or ladling. Granular AlC13 was added periodically to replenish that depleted from the electrolyte. Concentrations of 7.5 to 17.5 percent AlC13 in the electrolyte were optimum for operation. Anode current efficiencies of 83 to 85 percent were attained, using anode current densities of 5.9 amperes per square inch and an anode-cathode distance of 4 inches. The chemically bonded, alumina liner was resistant to attack by aluminum and chlorine but susceptible to erosion at the surface of the electrolyte. Titanium diboride proved suitable for the electrical connection to the molten aluminum cathode. Aluminum of a purity equal to or better than 1100 series metal was electrowon continuously from commercial AlC13 for a period of 4-1/2 months.

Jan 1, 1970

By Albert L. Toenges

A phase in strip mining of bituminous coal is the overturning of the surface of the land. The ;purpose of this report is to acquaint the operators and others interested in stripping with the work that has been done in certain States to reclaim the surface of land from which the coal has been removed by this method of mining. The preparation of this manuscript follows an extensive study of the subject in the field in the course of which a large number of strip mines were visited. ACKNOWLEDGMENTS The information used in the report was obtained through the courtesy and cooperation of the operators of the mines visited, State officials and educational institutions, and others interested in the subject.

Jan 1, 1939