Search Documents

The purpose of this paper is to present the methods used in ground water control and the considerations that affected the development of these techniques. Production at Knob Lake is currently proceeding at depths which may be as much as 200 feet below the original standing water table. In order to produce a more saleable product and to improve operating and maintenance conditions, it is necessary to depress the water table below the mining level. Considerable success has been achieved by drilling deep wells in strategic locations and installing vertical tur-bine pumps at depths of up to 400 feet. This method is especially suitable for operation under severe winter conditions and has reduced the detrimental effects by a far greater extent than other methods of water control, Spring runoff is handled in open sumps, but all other water from four mines, with flows exceeding 16,000 g.p.m., is pumped all year 'round from about thirty-five wells. T HE Knob Lake operation of the. Iron Ore Company of Canada is located on the Quebec-Labrador border, 320 miles north of Sept Iles,

Jan 1, 1965

By J. D. Zhu

A numerical model for predicting microporosity formation in aluminum castings has been developed, which describes the redistribution of hydrogen between solid and liquid phases, the transport of hydrogen in liquid by diffusion and Darcy flow in the mushy zone, One of the key features of the model is that it uses a two-stage approach for porosity prediction, In the first stage, the volume fraction of porosity is calculated based on the reduced pressure, whereas, in the second stage, at fractions solid greater than the liquid encapsulation point, the fraction porosity is calculated based on the volume of liquid trapped within the continuous solid network, which is estimated using a correlation based on the Niyama parameter, The porosity model uses thermal data calculated using the commercial finite element package ABAQUSTM. The model has been applied to examine the evolution of porosity in a series of experimental samples cast using unmodified A356 in which the initial hydrogen content was varied from 0,048 to 0.137 [cc/100g], A comparison between the model predictions and the experimental measurements indicates good agreement in terms of the variation in porosity with distance from the chill and the variation resulting from initial hydrogen content.

Jan 1, 2005

By Mowat D. M., Louis H., Smith W. Mackey W. M., Dron R. W., Ellison C. C., Winmill T. F., Kerr G. L., Haldane J. S., Ashworth J., Garforth W., O'Shea L. T.

Discussion of Winmill's paper, including various anecdotal examples, is presented together with the author's response; topics included: the need to distinguish cubic pyrites from the rapidly decomposing rhombic form known as marcasite; the effects of moisture content in the coal and air; the possible effect of pressure; the heat insulation resulting from heap/stack size; and the means of determining pyrite and moisture contents

Dec 1, 1916

By H. D. Goodfellow, R. A. Elliott

"This paper covers the evolution of large mills and autogenous grinding and compares grinding practice in the iron ore industry with that in the base metal industries. Comments on novel methods of grinding are presented for discussion. Recent developments in the field of classification are briefly reviewed. A systems analysis approach to grinding circuits is discussed. Finally, a point is made for establishing a group within the industry with the purpose of developing a comprehensive evaluation of grinding research and development."

Jan 1, 1971

By J. L. Bellanca, L. R. Swanson

DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the official position of the National Institute for Occupational Safety and Health, Centers for Disease Control and Prevention. Mention of any company or product does not constitute endorsement by NIOSH. ABSTRACT Proximity detection systems (PDSs) for mobile machines have the potential to decrease injuries and fatalities. Early adopters of the technology have identified some challenges, which presents an opportunity to explore and improve the integration of mobile PDSs in underground coal mines. The current study applied the task-technology fit framework to investigate the fit between mobile PDS technology and mining relative to health and safety, from the perspective of leaders at two coal mines. Quantitative results from the study show that mine leaders evaluated mobile PDS favorably for training and ease of use, system feedback, user authorization and experience, and less favorably for safety, compatibility, task completion, and reliability. Qualitative results reveal specific task, mine, and system characteristics that may have influenced leaders' evaluations. The study includes considerations for safe technology integration. INTRODUCTION Striking, pinning, and crushing accidents related to mobile machines continue to be a major concern in underground coal mining. The National Institute for Occupational Safety and Health (NIOSH) linked 22 of the 75 underground mine fatalities reported between 2011 and 2015 to power haulage [1]. The Mine Safety and Health Administration (MSHA) asserts that proximity detection systems for mobile machines (mobile PDSs) could help to prevent these types of fatal injuries [2]. Mobile PDSs use a collision avoidance technology that allows the mine to establish hazard zones and employ electromagnetic sensors to detect workers equipped with a miner-wearable component (MWC) working near these mining machines. The authors characterize a mobile PDS as an automated technology, because—in line with Lee & See’s [3] definition of automation—a mobile PDS actively “selects data, transforms information, makes decisions, or controls processes” (p. 50). When the system detects workers in the established hazard zones, it issues alerts and slows or stops the mobile machine. Even though a mobile PDS may be a viable and promising safety solution, there are still a number of questions regarding how well this automated technology will fit with mining tasks and conditions. Using a mixed-methods approach, the current study explored factors that influence the fit of mobile PDSs in the underground mining environment.

Jan 1, 2019

By J. Kempken, R. Hagmann, C. -P. Reip, W. Hennig

The CSP technology symbolizes a highly productive process for the cost-effective production of steel grades with a range of sophisticated properties comprising both the inner quality of hot strip, its surface formation as well as the relating technological characteristics. Thanks to extensive development work undertaken during the last 15 years, the range of steel grades that can be produced was continuously expanded and the process technology optimized. The present paper describes the ongoing development work concerning the production of higher-strength, microalloyed pipe steels. The resulting hot strip, due to the associated thickness and the potential pipe diameters, is particularly suited for being processed to HFI-welded pipes. Based both on ferrite-pearlite as well as very fine-grained, ferrite-bainite hot-strip microstructures, strength levels of up to grade API X80 can be realized. It can be demonstrated that hot strip produced in a CSP plant has very good toughness values at temperatures down to -60°C and can even make application with required sour-gas resistance possible.

Jan 1, 2005

By Q. H. Liao, B. G. Monaghan

The options for designing slopes in complex geological conditions are reviewed. It is shown that modelling, especially numerical modelling, allows a degree of analysis that cannot otherwise be achieved. Examples are presented of how numerical modelling can be used to investigate fundamental aspects of rock mass behaviour. It is demonstrated that an important consequence of change in scale is that the mechanisms of failure also change. The complex failure of the footwall slope at Aznalcollar, a large open-pit mine in southern Spain, is discussed. Numerical modelling with UDEC (universal distinct-element code) has allowed the realistic simulation of displacements measured in the field

Jun 18, 1905

By Donald W. Gentry

This paper presents some of the results of a rock mechanics in¬strumentation program designed for, and implemented at, longwall panel 4N at the York Canyon Mine near Raton, New Mexico. The objective of this particular instrumentation program was to determine the response of the rock mass to longwall mining of a thick coal seam utilizing shield-type supports. Measurements were made in the rock along the ground surface, above the coal seam, in the coal seam and immediately below the coal seam. Longwall test panel 411 had a total developed length of 762 m (2500 ft) and a face width of 168 m (550 ft). The seam mining height in the panel area was approximately 3 m (10 ft). The average depth of overburden above the panel is 107 m (350 ft) al¬though it ranges from 73-134 m (240 - 440 ft). Roof support at the face was provided by Hemscheidt shields. These shield-type supports weigh 11.4 metric tons each.

Jan 1, 1977

By L J. de Lange

As a material asset for mining entities, the resources and reserves (RR) estimation processes are surprisingly underrepresented in the assurance landscape. When press reports expose them being inaccurately reported, or in merger and acquisitions processes, their importance becomes clear. The impact of erroneous RR numbers (both positive and negative) could have a material impact on an entity’s reputation and value.The technical nature and ‘black magic’ connotations of the RR estimation processes are possibly reasons why audit committees are not actively involved with it. Internal auditors avoid the RR processes for similar reasons. Also the traditional approach to obtain assurance on RR is expensive and is therefore only performed when it is absolutely required.However, stakeholders’ expectations of good governance are growing. Part of this increased focus is based on attaining a higher degree of certainty about the current and forecasted position of the entity. Stakeholders are also increasingly more interested in non-financial areas of entities, as the future success of an entity is more than a set of financial metrics.Consequently, the RR estimation processes should be visible on the agendas of audit committees. Monitoring of key controls is required as part of the governance obligations for senior management and the audit committee. So once it is on the audit committee’s agenda, the question then becomes, how will that agenda be supported by an assurance process that is cost-effective?The main objective of the paper is to describe a model of RR assurance that has been effectively applied in some mining companies. The paper discusses one particular approach that provides an audit committee with the required assurance regarding RR processes. The approach ties the assurance needs of the audit committee to the needs of the technical experts in the entity, therefore involving two important figures. It also offers assurance providers with a model to audit ‘through’ the RR processes rather than ‘around’ them. The paper then discusses top-down and bottom-up approaches that provide assurance at different levels of an entity.A governance audit that focuses on the RR processes is suggested as a top-down approach. A bottom-up approach assesses the design adequacy of internal control processes. A hybrid model is described which meets the needs of diverse stakeholders including the audit committee and the RR community.The hybrid model combines the expertise of professionals in both internal audit and RR. The right balance of these skills directed by a singular approach ensures that a credible result is achieved.This approach is not as expensive as some verification approaches used in the industry and can, as a result, be performed on a more regular basis.The last element of the paper looks at implementation of the reporting mechanism. An assurance process aimed at continuous improvement further enhances the robustness and reliability of RR reported by an entity.CITATION:de Lange, L J, 2016. Resources and reserve assurance processes – a framework for improved governance, in Proceedings International Mine Management Conference, pp 21-34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By P. Ashtari

Influence of Sr and Mn single and combined additions on the modification of the Fe-containing intermetallic compounds and mechanical properties of Fe-rich AA319 aluminum alloys have been investigated, The microstructural features e,g, morphology of the Fe compounds and eutectic Si has been correlated to the mechanical properties, It was demonstrated that modification of the Fe compounds from the platelet ß-Al5FeSi to the Chinese script a-Al8Fe2Si compound improves the UTS and elongation of the alloys by 10.3% and 83.9%, respectively. Moreover, the simultaneous modification of the Fe compounds and eutectic Si increases the UTS and elongation of the alloys by 15,3% and 116,1%, respectively.

Jan 1, 2005

By William C. Smith

Roof support, an important aspect of ground control, involves maintaining roof competency to ensure a safe and efficient mining environment. Wide variability in rock quality and stress distributions requires a systematic approach to roof support design that satisfies specific goals. The success of past roof sup-port in reducing the incidence of roof falls has been primarily attributed to safer roof bolting practices. However, roof falls continue to be the number one occupational hazard in underground coal mines. This U.S. Bureau of Mines report presents a general overview of roof bolting and other roof support methods used in the United States. Characteristics of bad roof and associated roof failure theories are briefly presented as background to roof support. Methods of detecting and monitoring roof behavior and/or bolt performance provide essential feedback on roof support requirements. A discussion follows on roof bolt design that assimilates roof and support parameters into useful equations or nomographs to help decide what bolt types to use and how they should be installed under different roof conditions.

Jan 1, 1993

By T Ireland, B Wright, S Weaver

All tunnels have unique characteristics that result in different fire and life safety risk. The fire safety systems for each tunnel also give different benefits at different costs. It is therefore neither pragmatic nor cost-effective to prescribe specific fire standards requirements for all tunnels. Each tunnel needs to be assessed individually but using a common process.The owner/client is normally the risk owner and needs to make the decision on what fire and life safety provisions will be provided within the tunnel. To make this decision they need to be appropriately informed. The low probability and high consequence nature of fire events creates a challenge such that traditional analysis processes, which tend to focus on a major event after it has happened, are not easily applied and do not give the best value for money. Therefore a process is required that provides the relevant information to the owner for decision-making.A quantitative risk assessment (QRA) provides a process and framework for the consideration of fire life safety risk when applied properly. This involves a risk assessment of the ‘do nothing’ option together with assessments of improvement options and their costs. It also involves consideration of benchmark safety levels for other tunnels and the open road.This paper will outline a QRA process for assessing fire and life safety risk in tunnels and how this has been used for three existing tunnels, Homer Tunnel, Lyttelton Tunnel and Mt Victoria Tunnel. Key challenges include determining an acceptable safety level, defining realistic inputs, providing sufficient complexity to get meaningful results but not so complex that transparency is lost and interpretation to enable decision-making by non-technical personnel.CITATION:Weaver, S, Wright, B and Ireland, T, 2014. A transparent and pragmatic quantitative risk assessment process for assessing fire safety in New Zealand tunnels, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 121–128 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Corby G. Anderson

Antimony has been utilized by mankind for thousands of years. However, due to recent environmental concerns, antimony is often considered to be an impurity element, Since antimnoy is commonly found in precious metal refractory ore bodies, extraction is essential. The Sunshine Mine in Kellogg, Idaho has recovered antimony from its precious metal tetrahedrite deposits since the 1940's. A plant was initially constructed as a primary antimony source during World War II. This facility also decreased the downstream smelting penalty for the silver copper-lead concentrate and provided an industrial commodity from a potential environmental nuisance.' This paper describes the Sunshine antimony processing- facility. Specifically, the relevant process chemistries involved in concentrate leaching, metal electrowinning, and sodium antimonate production will be discussed. In addition, ongoing areas of research to improve unit operations and treatments implemented to meet environmental' discharge requirements will be covered.

Jan 1, 1992

By Mark A. Rohrbach, Timothy R. Kovacs, PhD Saidin

"Crosshole Sonic Logging (CSL) testing is commonly used to verify the integrity, quality and ultimately the acceptability of the concrete in structural elements such as drilled shaft foundations, secant pile cutoff walls, and secant/tangent pile earth retention structures. Besides concrete quality, many factors can impact CSL test results (e.g. laitance, air temperature, access tube spacing, access tube debonding, etc.). Effective use of CSL testing requires fully informed qualified practitioners capable of distinguishing between abnormal readings unrelated to deficiencies in the drilled shaft concrete and similar readings indicating the presence or possible presence of drilled shaft defects. Based on data and experience gathered from CSL testing of thousands of drilled shafts across North America, this paper discusses such factors and other information useful when evaluating CSL test results, and provides practical recommendations intended to reduce the potential for incorrect test data interpretation. The CSL testing industry is lacking in a clear, universally accepted guideline for the interpretation of CSL data and acceptance criteria of these concrete elements. This paper proposes terminology and a streamlined process for use when atypical results are obtained. The proposed terminology and method are intended to simplify and expedite the submittal review and approval process. Because construction activities for these elements are often on the project’s critical path, the benefits obtained in terms of project savings and reducing costly delays areundoubtedly valuable.1. INTRODUCTIONCSL testing is used extensively throughout the world on many projects to verify the quality of concrete used for drilled shaft foundations, secant pile walls, diaphragm walls, etc. In this paper, these structural elements will be referred to as “drilled shafts,” as they are the most common subject of this test method. In the United States, CSL testing is frequently specified by state and regional transportation agencies, ports, design builders, and others. Although other methods are currently available such as Gamma-Gamma Logging and low-strain Impulse-Echo or Sonic-Echo testing, and new methods are under development such as the Thermal Integrity testing, CSL testing is likely to remain one of the most useful tools for evaluating the acceptability of constructed drilled shafts for quite some time. The popularity of CSL as a testing method can be attributed to two main factors: 1) there is no depth limitation to the method and 2) the apparent ease of interpreting the results. A third advantage of CSL testing is that, when correctly interpreted and with adequate test coverage, it is unlikely to misrepresent a defective profile resulting in acceptance of a defective or inadequate drilled shaft. In other words, CSL testing is very likely to underestimate concrete quality/drilled shaft acceptability within its area of coverage."

Jan 1, 2017

By J. W. Paul

This circular is one of a series of reports on coal mining methods and cost s which are being prepared by the U. S. Bureau of Mines for the purpose of making available to those interested in the industry a knowledge of the mining methods employed in mines where mechanical and hand loading is practiced and the cost data on the several operations pertaining to the removal of coal from the working faces and its transportation to the tipple for loading into railroad cars. The methods employed are influenced by the natural local conditions with respect to the thickness and character of the coal beds and the overlying strata, the means employed for roof support and its control, and the disadvantages incident to the development of mines in thin coal beds.

Jan 1, 1929

By M D. Sussman

A large number of countries in the world now have some regulation for labelling the presence of genetically modified organisms (GMO) in food. For the last ten years, ISO/TC 34/SC 16 has been providing methods, guidelines and requirements concerning the evaluation of molecular biomarkers including GMOs. This activity makes sure that stakeholders on all sides of commercial transactions are satisfied and their marketing or regulatory needs are met. Developing and maintaining a transparent, science-based environment for users of horizontal methods for molecular biomarker analysis is a high priority. Sampling and analysis of molecular biomarkers has become critically important for food and agricultural organisations developing, producing, distributing and selling genetically engineered, non-genetically engineered, identity preserved and/or organic crops and their derived products and preventing their respective destructive diseases. To aid in international harmonisation, a new work item proposal to develop an ISO type A management system standard (MSS) for organisations including laboratories using molecular biomarker analysis and sampling has been submitted to ISO/TC 34/SC 16. The purpose of this MSS is ensuring that determination of the presence, absence or quantification of a particular biomarker with a relationship to a product quality determinant, a marketing claim, a regulation or a plant pathogen is carried out under a suitable quality assurance / quality control system. This MSS will provide an overarching system to apply and manage molecular biomarker analysis and sampling for any organisation large, medium or small in a private, government or academic setting.CITATION:Sussman, M D, 2017. ISO/TC 34/SC 16 horizontal methods for molecular biomarker analysis – molecular biomarker analysis and sampling management system, in Proceedings Eighth World Conference on Sampling and Blending , pp 295–302 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By Arthur Grounds

Historical In the course of a paper which is necessarily limited in length, such as the present one, it is obviously impossible to describe in detail the history, development, and present position of coal preparation in Western Europe. Great Britain has been blessed with large deposits of excellent coal of nearly every type, ranging from the high-grade anthracites of South Wales, which are characterised by their very low ash and volatile con-tents, to the superb coking coals of South Wales and Durham -probably the finest in the world -with their low ash and sulphur contents, the latter constituent often well be-low l per cent. Gas coals abound in Lancashire and Yorkshire, while coals from the East Midlands, Northumberland, and Scotland are excellent for steam-raising and other industrial purposes. The excellent quality of these various coals has, in years gone by, ensured ready .sales abroad and it is not surprising, therefore; that methods of coal preparation were largely developed on the Continent in an endeavour to upgrade the inferior fuels found there, so that the prepared product could compete with British coals on the European market.

Jan 1, 1951

The quality of refractory bricks and castables could be determined by direct measurements of their material properties such as elastic properties, porosity, density, etc. using conventional static or non-destructive testing (NDT) dynamic techniques. Quality monitoring of refractory linings is much more challenging and complicated. The static methods require undesirable drilling and sample extractions from the furnace structure. A more desirable alternative is the use of NDT techniques for material quality estimation. The Acousto Ultrasonic-Echo (AU-E) technique is a new stress wave propagation approach for monitoring the quality of refractory linings in operating furnaces. In this paper, the conceptual methodology for the AU-E technique is described, the capabilities and limitations are expanded, and the results from two case studies are discussed.

Jan 1, 2005

By J Ferreira

To speed up multivariate geostatistical simulation it is common to transform the set of attributes into spatially uncorrelated factors that can be simulated independently. One decorrelation method is the method of minimum/maximum autocorrelation factors (MAF), where a two structure linear model of coregionalisation is assumed. The transformation decorrelates the theoretical model exactly, but the actual data are only approximately decorrelated. The MAF transformation can therefore be seen as a special case of a non-orthogonal approximate diagonaliser of a set of symmetric matrices. A more general approach for approximate joint diagonalisation (AJD) has been developed in the context of blind source separation. For these AJD algorithms no assumptions are made beyond symmetry of the individual matrices and so they can be applied to a family of experimental semivariogram matrices. In their application there are no restrictions on the number of structures in the linear model of coregionalisation (LMC) thus removing one of the conditions placed on the subsequent modelling of the spatial structure of the factors. In this paper the general background for the U-WEDGE AJD method is presented. It is shown that the U-WEDGE method achieves better spatial decorrelation than the MAF method. The factors derived from U-WEDGE are simulated using conditional turning bands simulation and then backtransformed to attribute space.

Sep 26, 2011

The purpose of this paper is to present the methods used in ground water control and the considerations that affected the development of these techniques. Production at Knob Lake is currently proceeding at depths which may be as much as 200 feet below the original standing water table. In order to produce a more saleable product and to improve operating and maintenance conditions, it is necessary to depress the water table below the mining level. Considerable success has been achieved by drilling deep wells in strategic locations and installing vertical tur-bine pumps at depths of up to 400 feet. This method is especially suitable for operation under severe winter conditions and has reduced the detrimental effects by a far greater extent than other methods of water control, Spring runoff is handled in open sumps, but all other water from four mines, with flows exceeding 16,000 g.p.m., is pumped all year 'round from about thirty-five wells. THE Knob Lake operation of the. Iron Ore Company of Canada is located on the Quebec-Labrador border, 320 miles north of Sept-lies, a seaport

Jan 1, 1965