Search Documents

By N. G. W. Cook

The conventional cyclic system of deep-level mining by drilling and blasting gives rise to an inadequate degree of stope sorting when mining thin reefs. This results in poor utilization of the capital facilities of a mine in the form of shafts, haulages, airways and associated equipment. Continuous and controlled removal of the thin gold-bearing portion of the reefs would permit better stope sorting and hence greater utilization of capital facilities. Results of experiments to develop hard rock cutting machines for mining are reported and the benefits which could be derived from their use are discussed.

Jan 1, 1969

By M. M. Tilman

In a Bureau of Mines investigation to develop lead alloys with improved tensile strength and creep resistance, lead-base alloys containing cadmium and antimony in nominal 1-to-1 atomic ratios were melted in air, cast, and rolled into sheet to 90 percent reduction at temperatures varying from room temperature to 175° C. Tensile testing at room temperature and stress-rupture testing at 900±3° F were conducted on the as-rolled alloys. The best tensile properties were observed in an alloy of Pb-4.2 wt pct Cd-4.5 wt pct Sb which exhibited an average tensile strength of 7,270 psi with 36 percent elongation in 2 inches. An alloy of Pb-5.5 wt pct Cd-6.0 wt pct Sb had 100-hour stress-rupture values of approximately 2,100 psi and 1,000-hour values of approximately 1,700 psi.

Jan 1, 1969

By W. D. Forgeng, R. E. Grace

The rate of copper corrosion in liquid lead was studied as a function of flow rate and temperature in a closed isothermal loop system between 350" and 500°C. Kinetic data were interpreted with the Nernst-Brunner equation and the Chilton-Colbum mass transfer analogy to heat transfer. Over the range of temperatures and flow rates employed the solution rate constant varied from 2 x 10-3 to 20 x 10-3 cm per sec. The rate constant was found to vary with the 0.76 power of the Reynolds number in the range 7500 < Re < 40,000. The results of this investigation indicate that the Cu-Pb corrosion process is controlled largely by diffusion across a boundary layer. particularly at the higher temperatures. The effective boundary layer for diffusion is found to be approximately three to four times smaller than the momentum boundary layer. CORROSION by liquid metals has long been a problem during melting, static containment, and casting. Recently, considerable emphasis has been placed on the understanding of liquid metal corrosion mechanisms in an effort to prevent mass transfer and eventual failure in liquid metal heat exchangers and in liquid-metal-fueled nuclear reactors. The present investigation was conducted to determine the relationships which exist between corrosion kinetics and hydrodynamic conditions in an isothermal loop containing a simple liquid metal-solid metal corrosion system. The Cu-Pb system was chosen for its simplicity and ease in handling. Previous isothermal Cu-Pb corrosion studies1-3 have been conducted in both static and dynamic systems but not under conditions which allow easy "scale-up" to engineering systems, such as liquid metal heat exchangers. On the other hand, most liquid metal loops which have been used to evaluate mass transfer rates4 have been driven with temperature gradients under conditions of natural convection and unknown flow rates. The primary contributions of this research are twofold: 1) to evaluate the design of a simple isothermal loop corrosion system and 2) to investigate liquid metal corrosion behavior under well-defined hydrodynamic conditions. MATERIALS AND EXPERIMENTAL WORK The apparatus used to measure the Cu-Pb corrosion rates is shown schematically in Fig. 1. The loop system consisted of 1) a reservoir made of Type 316 stainless steel containing a centrifugal pump and 2) stainless-steel tubing containing a removable copper test section. The copper test section was OFHC hard-drawn tubing, 11.0 0.05 cm in length and 0.775 ±0.005 cm ID. A Type 316 stainless-steel venturi meter* was inserted in place of the copper test sec- tion in order to determine the lead velocity as a function of pump speed at each temperature. The Cu-Pb system was chosen for this study because the solubility of copper in liquid lead is large enough to measure accurately but small enough that the diameter of the copper tubing was not changed significantly by corrosion. There are no intermediate phases formed in the system, and the solid solubility of lead in copper is vanishingly small so that back-diffusion cannot occur. Molten lead (corroding grade; 99.94+ pct Pb, 0.0015 max pct Cu) was charged from an auxiliary melting furnace into the system under an argon cover to minimize oxidation. The lead was then maintained at constant temperature by a stirred molten salt bath in which the loop was immersed to a depth just above the lead level in the reservoir, Fig. 1. The total volume of lead in the system was 320 2 cu cm.

Jan 1, 1969

By R. L. Rock

The Bureau of Mines conducted radiation-ventilation studies in six large underground uranium mines to investigate the extent of radon-daughter exposure experienced by the miners and to analyze the ventilation systems to set what changes were required to achieve recommended radiation standards. The studies entailed tracing and measuring the mines&apos; ventilating air, quantitatively and qualitaitively, from its entrance into the mines, through production areas, and lack to the surface. Pressures consumed in creating airflow through mine circuits were determined by altimeter surveys. Air quantities were measured with anemometers or by chemical smoke cloud methods. Air quantities delivered through tubing were determined using U-tube water gages to magnahelic gages to measure velocity pressures. Radon-daughters were filtered from mine air to measure alpha activity; activity levels were converted to "working levels," the established unit for reporting miner exposure. Attention was given to locating unnecessary contamination influx sources and recirculating air. The radiation-ventilation surveys showed that where basic principles of food ventilation were not followed, high alpha radiation levels invariably resulted. Some mines required more primary air for controlling radiation levels throughout active areas, but more efficient use of available air was generally possible. Premature contamination of intake air was prevalent where development Openings intersected ore or passed by worked-out stopes. Several auxiliary systems were inefficient in secondary distribution, recirculating air already too highly contaminated for ventilation. Many got these common problems can be traced try the lack of dine planning with radiation control in mind.

Jan 1, 1969

By James J. Scott

Shale formations are the Nemesis of the Mining Engineer. Shales react to changes in environment in the most unusual and unpredictable manner. Increase in temperature may cause spalling, increase moisture and compression induced fractures may occur, and if a full face is exposed it may deteriorate due to atmospheric exposure. Combine only small amounts of shale in layered fashion with hard brittle competent rock and the whole structure may be fractured and fail due to stresses generated in and around the shale. In this paper the author will discuss failure mechanisms encountered under various field conditions and remedial action which may be employed by the engineer.

Jan 1, 1969

By J. C. LaScola

Development of methanometers and anemometers for underground use in coal mines is reviewed. The first semicontinuous recording methanometer was developed in 1961 in West Germany. The Bureau of Mines developed an instrument using; pellesters that was a continuous recording methanometer. Expansion of freon gas created a vacuum which pulled the methane-air mixture through a tube to an electrically heated, catalyst-impregnated pellester where the mixture was burned. The National Coal Board of England developed a continuous recording methanometer based on the principle of the Davy flame safety lamp. A thermo-pile was used to sense the hurt output of the flame. Finally the Bureau of Mines improved its methanometer by eliminating the freon gas and using a diffuser head to a monitor methane-air mixtures. Development of recording anemometers proceeded from the use of a photo¬cell and light source to sense rotation of the Biram-type anemometer blades to the use of a Hall detector to sense, rotation by measurement of electromagnetic pulses.

Jan 1, 1969

By Verne E. Hooker

In situ stresses, based on isotropic and anisotropic relations, were evaluated using computer techniques from overcoring data obtained in dimension stone quarries along the Appalachian Piedmont, the Ozark Uplift, and the Ouachita Tectonic Belt. Stresses in the horizontal plane near the surface are compressive and range from 100 to 4,500 psi. The direction of maximum compressive stress seems to be alined with the general tectonic structure for most of the determinations. The ratio of the maximum to minimum elastic parameters in the horizontal plane ranges from 1.05 to 2.46 for these competent rocks. Isotropic versus anisotropic stress determinations show differences only as great as 25 percent in stress magnitude and 25° in orientation.

Jan 1, 1969

By Donald S. Colby

This Bureau of Mines report is essentially a handbook, or manual, for making the type of mineral resource valuation commonly required for such public policy problems as mineral leasing. The principle of resource valuation through the capitalization of cash flow is well established. A mathematical procedure, based on a simplified accounting system, is detailed for calculating cash flow from revenue, plant costs, and operating expense. Variations of procedure cover cost depletion, percentage depletion, and depletion limited to 50 percent of net income. The influence of the depletion provisions of the tax regulations on the value of a resource to an owner and to an operator is analyzed. The relationship of royalty, bonus payments, and sales price to resource value is also described, and methods for approximating resource values using these payments as input data are developed.

Jan 1, 1969

By Valerie Kollonitsch

Functional mineral pigments are used in large quantities in paint, paper, plastics, rubber, textiles, agriculture, and several other industries. U.S. consumption in 1969 is estimated at over 5 million tons a year, valued at nearly $150 million, as shown in Table 1. Originally extender pigments were employed only to lower cost. They were thought of merely as adulterants to replace more expensive prime pigments and binders. However, over the years their role has become better understood, and today their main functions are: - Increasing strength, stability, and service life. - Improving surface properties. - Enhancing application and processing properties. - Extending prime pigments. - Controlling viscosity and package stability - Lowering overall costs of the finished product. The principal minerals used as functional pigments are kaolin, ground calcium carbonate, talc, and asbestos. Other minerals include barytes, attapulgite, diatomite, mica, ground silica, wollastonite, and nepheline syenite. Several synthetic products, including precipitated calcium carbonate; precipitated, gel, and fumed silica; alumina trihydrate; and barium sulfate, compete with mineral products. They are more expensive, but often have more closely controlled particle size or other properties because they can be tailor-made according to the requirements. This paper covers only natural products selling for $10 or more a ton, approximately the lower limit for pigment grades. Data refer only to consumption in pigment applications. For example, such applications as filter aids for diatomite are not included. Key properties of the major mineral pigments are given in Table 2. It is important to note that these properties are primarily physical rather than chemical. In general, these products are sold to performance specifications for what they can do rather than on chemical composition specifications on what they contain.

Jan 1, 1969

By William O. Rasmussen

Exploration requires processing highly varying kinds and amounts of geologic information. Successful discovery dictates that this be done quickly with maximum confidence. Most phases of exploration are more or less applicable to computer reduction on a routine basis. The use of digital computers to reduce raw data into interpretable form, lets the exploration geophysicist concentrate on interpretation and presentation, and to consistently apply more sophisticated and comprehensive analytical techniques, not practical before. In applying these concepts for the past several years, various efficient programs have evolved which provide more complete evaluation of all data including the pro- vision for more unique solutions. This has resulted in greater refinement and ability to select the most advantageous drill sites in a minimum time at a minimum cost or, in rejecting as soon as possible a project on which additional effort is no longer justified. Practical examples of computer applications in magnetics (air and ground), induced polarization and resistivity are discussed.

Jan 1, 1969

By Wallace N. Thomas

The present interest in large diameter grinding mills and the rapidly rising cost of the drive in proportion to the cost of the mill establishes a need to explore the drive system in detail. The drive for a seven to eight thousand horsepower mill will cost from 1350 thousand to $600 thousand which represents nearly half the total cost of the mill package, and requires as much building space as the mill proper. Some of the drive components require a longer time to manufacture and the installation time and costs are equal to those for the mill. It is apparent that the drive has become a dominant factor in the overall mill design consideration. A new plant requires a tremendous investment in both time and money. With the high degree of competition in the mining industry, low capital cost is an exceedingly important factor in the development of a project. It is just as important, however, to insure that the equipment is going to perform satisfactorily for the anticipated life of the project without adding unplanned operating, maintenance and replacement costs. This is the position in which the engineer or designer usually finds himself and is really one of his primary functions -- establishing a realistic compromise between cost and performance.

Jan 1, 1969

By Harry Perry

A technology for producing liquid fuels from oil shale at prices competitive with crude oil prices is a necessary but not exclusive prerequisite for the development of a shale oil industry. Many other factors will affect the timing and the rate at which oil shale is commercially developed. Among the more important are: governmental policy concerning oil shale and oil resources (including the Outer Continental Shelf) that are under Federal control; oil import policy; Federal taxation of shale oil production including depletion allowances; regulatory practices; competition from other energy sources, both synthetic and natural; Federal treatment of factors affecting competing energy resources; and present legislation under which the public resources must be leased. Significant changes in any of the foregoing factors could have a controlling effect on the timing and rate of oil shale development. The effect of changes in each of these factors is evaluated.

Jan 1, 1969

By P. C. Good

The Bureau of Mines conducted a laboratory investigation of a sinter-leach method to recover aluminum and fluorine from waste carbon potlining residues from secondary cryolite recovery operations in aluminum reduction plants. After removal of carbon by burning, the residue was sintered at 900° to 1,100° C with silica and N2CO3, then crushed and leached with dilute NaOH solution, dilute Na2C03 solution, water, or water containing residual Na2O which remained in the sinter after reaction and decomposition of Na2CO3. Over 90 percent of the contained aluminum and up to 87 percent of the contained fluorine were extracted from this waste product in the form of a mixed alkaline solution. Treatment of the alkaline solution with CO2 yielded a white precipitate containing 89 percent of the original aluminum and 61 percent of the original fluorine as a mixture of synthetic cryolite and alumina, together with a variable excess of soda.

Jan 1, 1969

By d&apos, I. J. Agati

The stockpiling and reclaiming of bulk materials can be a challenging task for engineers seeking the optimum solution for plant needs, reliability, and at lowest unit cost. The objective of this paper will be to expose advantages, disadvantages and limitations of many storage and reclaiming systems to the responsible engineer and management. The paper will emphasize the practical aspect of stockpiling and reclaiming methods. Many valuable and interesting papers are available dealing with the theoretical viewpoint and application of a particular manufacturer&apos;s machine. Several of these are mentioned in the bibliography. As many practical parameters as possible will be given. After twenty years in the field of designing and selling bulk materials handling systems, the needs of the user and the plant are recognized and reasonably understood. This paper cannot give solutions to all problems In this vast field but will stress practical applications and examples of various installations. The evolution of advancements in materials handling is based upon not only technological innovations, but learning from many experiences of others and utilizing them as stepping stones to improved installations.

Jan 1, 1969

By D. McLean

For many pu@oses uniform strength is desired over a long temperature range, coupled to a band of softness at the hot end for easy shaping. Various types of material fulfill such a requirement to different degrees, depending on the regularity of their atomic structure. In long-chain polymers and vitreous glasses the irregular structure leads to a steep temperature dependence of deformation resistance and the temperature band between the hard and brittle condition and the soft condition is only about 100 C. In crystals and especially metals the atomically regular structure leads to a much smaller sensitivity over a wide temperature band, thus approaching the ideal behavim. The reason for this insensitivity is that the regular crystalline structure deforms by the movement of dislocations and the elastic interactions of dislocations in- PLASTICS, GLASSES, AND CRYSTALS The ease or otherwise of deformation varies with temperature much more in some substances than in others. This is an important matter when service over a wide temperature range is needed, especially volve energies of several hundred electron volts compared with which the energy of thermal agitation is insignificant. However, temperature affects a metal&apos;s defmmation resistance through its influence on the annealing, m coarsening, of the three-dimensional dislocation network. This coarsening is a phenomenon very similar to grain growth and ideas about grain growth can be applied to it. Taking into account also the temperature dependence of the glide resistance from alloying additions, a reasonable account can be given of the overall effect of temperature on deformation strength and of stress and grain size on deformation rake. Special structures me described. some arising from these ideas and as yet untried, which may benefit metals and polymers but not ni-treous glasses. when in addition a degree of softness suitable for shaping is required at some stage. It would be nice if one could write on this subject in as much detail about plastics, glasses, and so forth, as about metals, but there has been far more study of this matter in metals than in other substances, which is one reason why most of this paper concerns metals. However, in Fig. 1 there are shown the deformation strengths of several nonmetallic substances as a function of temperature. In many tests the attempt at deformation caused breakage and the graph lines are then drawn dashed. Long-chain plastics, a glass, and a crystalline substance are included in Fig. 1. The notable feature of all of them is the sensitivity of the

Jan 1, 1969

By A. Roy MacLean

This paper outlines the changes in modern-day coal mining that have been brought about by the increased cost of labour and the use of new and highly efficient equipment. In the latter category are mentioned the ramp-plate, the Bretby cable carrier, armoured face conveyors and the shearer-loader. Greater productivity and increased safety are emphasized.

Jan 1, 1969

By J. D. Hunt, D. T. J. Hurle

A uariety of eutectic structures are formed in faceted/nonfaceted eutectics. The various structures are explained in terms of the absence or presence of small facets in the liquid groove. Regular structures are produced when, for purely geometric reasons facels cannot form. The presence of a facet in the liquid groove leads to the formation of an irregular or a cell-like complex regular structure, due to the relative immobility of the groove. A classification of eutectics was proposed by Hunt and jackson, based on the presence or absence of facets on the primary phases (the absence of facets may be predicted from the dimensionless entropy of melting2). Eutectics were divided into three groups: 1) eutectics in which both phases grow in a nonfaceted manner; 2) eutectics in which one phase grows faceted, the other nonfaceted; 3) eutectics in which both phases grow faceted. It was suggested that regular1 rodlike or lamellar structures1 should be formed in the first group, that irregular or complex regular structures1 should be formed in the&apos; second, and that irregular structures1 should be formed in the third. Recently it has been shown that the structural classification is incomplete. Regular rodlike structures (InSb-NiSb eutectic3), or broken lamellar structure (Bi-Zn eutectic, Fig. 8), are formed in alloys of the second group when the faceted phase has a large volume fraction. Hunt and jackson&apos; argued that regular structures could form in faceted/nonfaceted systems, but that such structures would be unstable in the presence of microfacets on the lamella of the faceting phase, because the growth rate at a point on such a facet would depend on the kinetic undercooling at the point of nu-cleation on the facet, and not on the local kinetic undercooling. In these circumstances it would not be possible to consistently balance the compositional and kinetic undercooling over a lamellar structure and thus obtain a stable isothermal interface. In this paper we discuss in detail the origin of the various structures formed in faceted/nonfaceted systems, pointing out that the most important factor promoting the formation of a regular structure is the absence of a facet in the liquid groove. 1) FACET FORMATION IN SINGLE-PHASE MATERIALS Facets form when there is an energy barrier for the addition of a new solid layer on an existing solid. When a barrier is present,2 growth proceeds by the lateral movement of steps across a crystallographic plane. The rate-controlling stage of the process occurs when the step is first formed. Hulme and Mullin6 have shown that faceting in single-phase materials can only occur when both interface curvatures are convex with respect to the solid and when the surface is tangential to the facet plane. When even one of the curvatures is concave a facet does not form because new layers of solid from adjacent regions can always feed the facet plane, Fig. 1. Growth under these conditions is then as easy as elsewhere. Similar considerations will apply to eutectic growth; consequently the shape of the faceted phase is extremely important. 2) LAMELLAR SPACING CHANGES IN EUTECTICS Jackson and Hunt7 have shown that the interface undercooling AT of a growing lamellar interface (neglecting kinetic undercooling) is related to the lamellar spacing, A, and growth velocity, v, by an expression of the form: where m, Ql, and nL are constants of the system given in Ref. 7. Eq. [I] is plotted for fixed v in Fig. 2. Jackson and Hunt postulate that a regular eutectic grows near, but to the right of the minimum in the AT vs A curve. They argue that the spacing cannot be to the left of the minimum because the interface is then unstable to fluctuations in A. It cannot grow too far to the right, because when the spacing becomes too wide an isothermal interface can no longer be maintained over the large-volume-fraction phase.7 It is argued that during any change in growth rate the lamellar spacing remains in the permitted range by the movement of lamellar faults. When the spacing is too wide, the fault, shown in Fig. 3, moves to the left; when the spacing is too narrow it moves to the right. The faults, however, have to be formed. heir formation has been shown to occur when local regions deviate considerably from the spacing defined by the lamellar When the spacing is locally too narrow (it passes to the left of the minimum, Fig. 2), pinching off of the narrow phase occurs. When the spacing is locally too wide, the interface on the large volume-fraction phase can no longer be maintained as an iso-

Jan 1, 1969

By Robert L. de Beauchamp

The Bureau of Mines reviewed aluminum chloride technology to determine the problems associated with its preparation from minerals, and to ascertain the best areas for research to solve these problems. Commercial AlC13 production processes are described and the ?state of the art? for the preparation of AlC13 from aluminous materials is evaluated. Areas for further research are indicated.

Jan 1, 1969

By Peter F. Mataich

The phosphate mining industry is a highly competitive one, one in which survival depends on the plant&apos;s ability to produce at costs equal to, or below, the competition. The solution toward getting costs down is usually one of scaling up the plants to get the most tons through at the lowest possible cost. Control of these plants has been an art. Few of them are well instrumented because until a few years ago reliable instrumentation was non-existent. International Minerals and Chemical Corporation was a pioneer in applying computer techniques to ore reserves analysis and mine planning and the success in these areas led to the question of whether we could not extend the advantages of computer processing into the plant itself. There was a great deal of doubt on the operator&apos;s end that this could be done successfully because of the lack of instrumentation and the fact that plant control was largely an art that was learned only after many years of experience. However, in 1965 the instrumentation picture began to look up and the new generation of process computers just coming on the market were considerably lower in cost than the previous ones. A preliminary study of the installation costs and the probable benefits that could be realized from computer control convinced us that a process control computer should be seriously considered for a new phosphate mining plant which was being designed.

Jan 1, 1969

By Michel David

One of the most important questions that arises in ore estimation can be stated as follows: What is the error when one extends the grade of a sample to a certain volume? The theory of regionalized variables, with the concept of extension variance, provides a response to that crucial question for any kind of sample extended to any volume. For the usual "extensions" encountered in current mining practice, some simple results can be derived from that theory which was initiated by Dr. G. Matheron. These results have been applied to a stratiform lead-zinc deposit for which several estimations of grade, tonnage and related precision have been made for a series of grid sizes such as might be used in a progressive exploration program.

Jan 1, 1969