Search Documents

By G. H. Bennett

A field experiment was performed in a production unit of an operating copper room and pillar mine to compare the support capabilities provided by resin and mechanical roof bolts. Resin and mechanical roof bolts were alternately installed in eight intersections in a single entry. Rock mechanics instrumentation was installed to measure roof sag, bed separation, convergence, bolt pullout, torque, and strain. Bolt cost and installation time are included. Two analyses of the test were made. The analysis of the rock mechanics data showed there was no definite difference between the two bolting systems. From a broader analysis on a mine-wide basis it was concluded that resin bolts gave better support. A critical view of the experiment is given in the appendix.

Jan 1, 1974

By W. K. Overbey

The Bureau of Mines conducted surface joint and stress measurements, airborne remote sensing imagery studies, compass-oriented borehole televiewer surveys, numerical simulation of fractured wells, and well productivity studies in a four-quadrangle study area of Ohio, to determine the effects of earth fracture systems on the deliverability of gas storage fields. The results of these studies indicate that much useful information about a gas storage reservoir can be obtained and put to practical use by studying--(1) oriented cores for fractures and directional permeability, (2) orientation of induced hydraulic fractures for alignment of well patterns, and (3) aerial photos and multispectral scanner imagery for general surface geology comparison and to determine if some, development patterns can be generated by such results. The absence of known tectonic elements associated with flat-lying sediments, such as faults or fracture zones that can be seen on the surface, indicates that the use of remote sensors such as radar or aerial photography is not likely to be useful in picking well locations for drilling. Studies similar to those discussed here should be conducted in gently folded and strongly folded sedimentary formation areas to determine if the increased knowledge of earth fracture systems under these conditions might be beneficial in gasfield and gas storage reservoir development.

Jan 1, 1974

By J. W. Adams

Two different techniques were wed to make measurements of the absolute value of electromagnetic noise in an operating hardrock mine, Grace Mine, located near Morgantown, Pennsylvania. Diesel-powered haulage equipment is used in this mine, and the electromagnetic noise environment it creates was measured to see how it differs from the environment created by electric-powered haulage equipment. One technique measures noise over the entire electromagnetic spectrum of interest for brief time periods. Data are recorded using broadband analog magnetic tape and are later transformed to give spectral plots. The other technique records noise amplitudes at several discrete frequencies for a sufficient amount of time to provide amplitude probability distributions. The specific measured results are given in a number of spectral plots and in amplitude probability distribution plots.

Jan 1, 1974

By Barry L. Warner

This program involves the evaluation of means for suppressing fires on underground coal mine conveyor belts. Full scale conveyor belt fire tests were conducted to determine the requirements of automatically actuated water sprinkler, high expansion foam, and multi-purpose dry powder extinguishing systems, and of various fire detection devices, necessary to adequately protect underground belt heads. The program included the development of a suitable MI scale conveyor belt test fire, conducting of fire tests in which extinguishing and detection systems and equipment were evaluated, and testing to evaluate the effects of the coal mine environment on detection equipment. Preliminary testing conducted to develop a suitable test fire revealed that fire can propagate on some conveyor belting classified as fire-resistant. New fire-resistant PVC and new non-fire resistant rubber belts were used in the full scale fire tests. These tests indicated that a single branch line sprinkler system with relatively low water pressure provides adequate belt head protection. High expansion foam and multi-"purpose dry powder extinguishing systems as presently specified by regulation were found to be suitable for belt head protection, although care is required with powder systems to assure adequate distribution. Thermal type detection devices were found to be most practical for conveyor belt protection, with combustion products and optical detection methods having serious disadvantages.

Jan 1, 1974

This report presents the results of a study of mill tailings disposal practices and potential tailings dam stability problems. Recognizing the long period of time that would be required to develop the technology and practices necessary to significantly improve refuse disposal safety, the Bureau initiated this research effort as a first step in that development. Volume 1 includes a summary of conclusions and recommendations resulting from the overall research effort; discussions of disposal systems and methods, geology, seismicity, hydrology, and materials characteristics; evaluations of investigational techniques; discussions of usable interim generalized investigational, analytical and inspection procedures; discussion of general principles and presentation of a tailings technology manual outline; and discussion of needed future research am recommended programs.

Jan 1, 1974

Volume 2 presents the results of studies of Phelps Dodge Corporation's tailings embankments numbers 1West and 2 West, at Morenci, Ariz. The work involved compilation and description of pertinent factors relating to the physical features and operational characteristics of the facility, including information on embankment construction practices; investigation and research of the general geologic and seismicity characteristics of the site and vicinity; limited field exploration and materials sampling and testing at the site; installation and limited monitoring of piezometers, surface movement markers, and slope indicator casing; limited laboratory testing of materials to evaluate the basic index and engineering properties of the embankment and tailings materials; selected engineering analyses of the embankment for various types of potential "failure" conditions; and includes appendices.

Jan 1, 1974

Three complete connector assemblies and six separate contacts were submitted to a series of tests to establish the connectors permissibility and compliance with U. S. Bureau of Mines research Contract #H 0110423 D.C. portion. Test Procedure TPC-0118 was coordinated, and the test plan approved by the Bureau as fully complying with the intent of the contract for the direct current connectors. The components and connector assemblies have been demonstrated in testing that they meet or exceed all the requirements of the test procedure.

Jan 1, 1974

By Richard A. Busch

Inadequate engineering design criteria for coal refuse embankments has allowed hazardous impoundment structures in coal mining areas to be created. A necessary first step to develop adequate design criteria is the determina¬tion of basic, respresentative physical property data on the materials that constitute typical refuse embankments. An extensive field and laboratory program was undertaken by the Federal Bureau of Mines. Much physical property data was generated. Additonal petrographic analysis and large scale triaxial compression testing was performed by others. The data presented here should aid in establishing design parameters for coal refuse embankments

Jan 1, 1974

By R. Stefanko

This study concerns itself with the effects of diesel exhaust on mine ventilation systems. The approach here consisted of the development of mathematical models for emissions, dilution, and dispersion of gaseous pollutants from diesels. The general scheme was to use partial differential equations to predict concentration growths. Specifically, the following situations were modeled: 1. A single stationary diesel engine working in a single roadway. 2. A single diesel engine moving with uniform velocity in a single roadway. 3. Multiple diesel engines moving continuously in a cycle in a roadway with appreciable leakage. 4 Multiple diesel engines moving continuously in a cycle in a roadway with little or no leakage. 5. Multiple diesel engines moving randomly in a roadway with uniform air velocity.

Jan 1, 1974

This Bureau of Mines report is a reference manual of procedures used by the Bureau's Twin Cities Mining Research Center for obtaining rock properties. Included in the report are discussions on the usage of each property, descriptions of the general test methods for obtaining the properties, and instructions for performing the tests. The Instructions embrace details of the specimen configuration, test apparatus, test procedure, test conditions, and calculations needed to achieve satisfactory results. Although the procedures presented in this reference manual generally conform to recommendations of the ASTM Administrative Committee on Standards, they are not purported to be standards.

Jan 1, 1974

By Erle C. Donaldson

Subsurface injection of liquid and slurry-type industrial waste is being used as a means of waste disposal. This survey conducted by the Bureau of Mines shows that the method can be economically and environmentally attractive if the proper precautions are taken, especially when the alternative is cursory treatment and discharge at the surface. Attention is called to petroleum technology and experience that can be applied to subsurface waste injection. Part 1 of this report is a discussion of the general aspects of subsurface waste-injection systems. Part 2 is a general discussion and review of the literature concerning the geologic formations available for injection in the United States. Part 3 is a discussion if 15 case histories including information on the source and nature of the waste and the geology, surface equipment, well completion, and operation of the systems.

Jan 1, 1974

By Klaus L. Cappel

In 1972, the Bureau of Mines of the U. S. Department of the Interior commissioned the development and design of a Simulator for research and testing of mine roof supports used in long-wall mining. The purpose of the Simulator is to reproduce forces and displacements of a section of a mine roof in contact with one or more supports. This report is an account of the design process that resulted in the final configuration of the Simulator presented here. It includes discussions of engineering considerations that led to major changes in important details of the Simulator. These changes, however, did not substantially alter the basic design originally proposed, except for the elimination of certain originally-specified features that were adjudged as insufficiently cost-effective by both the Bureau of Mines and the design agent at an intermediate stage of the design.

Jan 1, 1974

Sixteen papers concerned with the technology and utilization of low-rank fossil fuels are presented as the proceedings of the 1973 lignite symposium. This symposium, the seventh in a series of biennial meetings, was cosponsored by the Bureau of Mines and the University of North Dakota.

Jan 1, 1974

By Robert L. Lagace

This final report documents the work dune by Arthur D. Little, Inc. (ADL) on behalf of the U.S. Bureau of Mines, Pittsburgh Mining and Safety Research Center (PMSRC), on Contract H0122026 (which began in August of 1971). Under this contract ADL provided technical assistance to the Bureau on a task basis on virtually all aspects of the Bureau's programs related to present and planned emergency and operational communications and miner location systems for underground coal mines. The work consisted of independent investigations, analyses, experiments, breadboard and prototype hardware development, workshops and technology transfer seminars on mine communications, and on-going evaluations and guidance related to the Bureau's contracted programs on electromagnetic noise, mine communications systems, and trapped miner location. This final report documents the work in two volumes, Volume I, "Emergency and Operational Mine Communications," and Volume II, "Seismic Detection and Location of Isolated Miners." The Tables of Contents of both Volumes are included in each Volume. Phase I of the contract was devoted to performing an in-depth assessment of electromagnetic noise measurements taken by several contractors and other investigators, and then defining a new noise measurement program and instrumentation system tailored to obtain the necessary but missing noise data. These data are required for use in the design of new emergency and operational communication systems. This work, and the follow-on coordination and guidance activities of ADL on this noise measurement program in subsequent phases of the contract, are treated in Part One of Volume I.

Jan 1, 1974

This report presents the results of studies of Kennecott Copper Corporation's tailings embankment at Magna, Utah. The stability studies described were performed on only one cross section of the embankment, utilizing; data obtained from drilling, sampling, and testing, which was limited in nature. The main objective of the data collection was to provide background information to support the overall research effort. Because of this limited scope, it is not possible to evaluate the degree of safety or adequacy of the embankment or disposal system, and the information and data contained in the body of this report must be judged in that light. The first part of this report contains discussion of site geology and seismicity, pertinent information on the refuge disposal system, a discussion of the tailings materials characteristics, a summary of the engineering analyses, and A bibliography. The second tart (appendices) contains basic geologic and engineering data supporting the discussions in the first part of the report.

Jan 1, 1974

By David A. Hill

This volume contains a summary of the results of past analyses on U.S. Bureau of Mines Contract No. 80122061 which are relevant to electromagnetic location in mine rescue situations. The analytical results indicated that detection of a trapped miner equipped with a special transmitter is feasible in most situations. Location of the miner by surface measurements is also generally feasible within certain errors. The feasibility of miner detection and the accuracy of miner location have been examined theoretically for a wide variety of situations. Agreement with experimental results is generally good in cases where measurements are available. Personnel involved in the investigation include J.R. Wait (Principal Investigator), D.A. Hill (Co-Principal Investigator), K.P. Spies, A.Q. Howard, and Lana Slusher (Administrative Assistant).

Jan 1, 1974

By A. D. McMahon

Changes in world mine and smelter supply sources of zinc have led to changes in zinc supply patterns in the United States during the past 3 years, 1970-72. The result has been a growing reliance on foreign sources of zinc metal to furnish an ever-increasing portion of expending domestic requirements. This review of fundamentals and historical developments is intended to provide background in order to place the future of the U.S. zinc industry fn perspective. The properties and uses of zinc are described. A new study on U.S. reserves is presented with description by geographical region and comparisons with older reserve data. The technology of the zinc industry from prospecting through refining is described with emphasis on the metallurgy involved in the various methods of smelting. Production, consumption, and imports are discussed and illustrated with graphs and tables to review the past and present patterns. Government actions affecting the industry are shown.

Jan 1, 1974

A compilation of papers presented at The Second WVU Conference on Coal Mine E1ectrotechnology in Morgantown, West Virginia on June 12 -14, 1974. Papers cover areas of electric power, electronic communications, detection and location of trapped miners, and electronic sensors and monitoring systems.

Jan 1, 1974

This report contains the papers presented at the Technology Transfer Seminar on Ground Control Aspects of Coal Mine Design held by the Bureau of Mines on March 6, 1973, in Lexington, Ky. Seminar attendance consisted of representatives from the coal mining industry, universities, mining consultants, instrument manufacturers, and local, State, and Federal Government. The purpose of this meeting, one of a series of Technology Transfer seminars, was to provide the coal mining industry with detailed information about recently developed techniques, equipment, and instruments which can be used in the solution of coal mine design problems and to discuss results and direction of research in mine design. The report includes opening remarks by Joseph J. Yancik, Acting Assistant Director--Mining; an overview of the Federal Bureau of mines approach to mine design; three papers an problems associated with the design of panels; five papers on coal mine roof problems; three papers on long wall problems; and the comments made by- the participants on the Bureau-industry panel discussion.

Jan 1, 1974

By C. B. Manula

This report is volume 5 of an eleven-volume final report for a Grant completed by The Pennsylvania State University for the Bureau of Mines to develop a dynamic general purpose computer simulation model for underground coal mining. The simulator developed under the Grant has a wide range of possible applications in the design and evaluation of underground coal mining systems from the standpoints of health and safety, productivity, and mine environment. The Master Design Simulator consists of nine free-standing function-oriented subsystem models linked together into an integrated, comprehensive model of an entire mining system. The subsystems comprising the Master Design Simulator include geology and reserves, methane generation, roof support, subsidence, production, rail haulage, cost, water generation, and ventilation. This volume of the final report describes the Subsidence subsystem of the Master Design Simulator. This subsystem uses the finite element method to simulate ground movement caused by an advancing mining face in an underground coal mine. The model is structured around the concept that the ground mass is a layered media of different thicknesses and material properties. Gob areas are considered to be unfilled with broken rock at the beginning of mining. After mining starts, the gob areas are filled with broken material which provides resistance to the lowering of the overlying strata. The model is tied to the Geology and Reserves subsystem, but it can also operate as a free standing routine. A case study is presented illustrating the application of the model. A detailed user's manual, including a program listing, is included in the appendices.

Jan 1, 1974