Search Documents

By Edward D. Thimons

The Bureau of Mines conducted in-mine tests to determine correction factors applicable to low-velocity airflows (below 150 fpm) measured by the smoke cloud, vane anemometer, and oil of wintergreen tracer gas techniques 0 The average correction factors found for these methods of measurement were lower than those reported in the literature for use with higher velocity measurements. All tests measured airflows with controlled average velocities ranging from 50 to 100 fpm. Correction factors averaged about 0.75 for readings taken by the centerline smoke cloud method, remotely controlled and stickheld center" line anemometer, and split traverse stick-held anemometer. For hand-held centerline anemometer and oil of wintergreen tracer gas readings, correction factors averaged about 0.67. Since special anemometers are needed to measure airflows in this low-velocity range, and since proper calibration of these anemometers is difficult and expensive, the use of anemometers for low-velocity measurement is imprac-tical. On the other hand, smoke and oil of wintergreen give results as con-sistent as those obtained with specially calibrated, low-velocity anemometers. Furthermore, they are easy to use and inexpensive.

Jan 1, 1979

By W. Fergusson

This paper takes a look at the use of rubber to provide corrosion resistance and wear resistance in the mining industry. The longer life and reduced down time involved with the use of rubber are stressed, and examples are given of applications in grinding mills, skips, discharge chutes and screens.

Jan 1, 1979

By Peter A. Hacquebard

Recent drilling programs have shown that the in-situ coal resources of Nova Scotia are very substantial. The grand totals of the measured, indicated and inferred categories amount to 232 m, 646m and 993 m tons, respectively. This vast quantity of coal occurs essentially in five main fields: Sydney, Mabou, Port Hood, Pictou and Springhill. The largest resources (84% of the total) occur in the submarine area of the Sydney coalfield. With a 65% recovery rate, there are at present 150m tons of proven, recoverable coal in Nova Scotia. At a predicted maximum annual production of 5 m tons, this amount equals a lifespan of 30 years. However, additional drilling, particularly in the Sydney offshore area, holds promise of increasing the recoverable reserve tonnage to at least 350 m tons. This figure may be compared with the 484 m tons production obtained during 191 years of mining (from 1785-1976). The geological appraisal of the remaining coal resources in the five fields mentioned is presented in three-dimensional diagrams, per individual seam and corresponding reserve area. In addition, the submarine extensions of the Sydney and Mabou coalfields are discussed in light of results obtained from off shore oil exploration wells. The terminology and standards of coal resource calculations are pointed out, and the phenomenon of seam splitting and its prediction from geological data is illustrated. The availability in Nova Scotia of either thermal or metallurgical coal is considered in relation to rank and sulphur content. This paper was presented in June 1977 at the 90th Annual Meeting of the Mining Society of Nova Scotia. The coal resource estimates, however, have been updated to include the results obtained with the offshore drilling in the Sydney Coalfield to November 1977.

Jan 1, 1979

By Brian Raymond

This paper will outline the problems and solutions of the new generation washeries, as well as the recent technological advances which are being considered for future coal preparation plants. The subjects to be covered will include: - reasons for considering coal preparation plants; - raw coal crushing and handling systems; - types of coal cleaning equipment being used versus new equipment being considered; - fine coal circuit sizing; - clean coal centrifuging and dewatering; - thermal dryer problems and changes; - fine refuse dewatering systems; - clean coal storage problems and changes; - materials handling within the plants; and - control systems for preparation plants. The design and integration of the various circuits that form a modern coal preparation plant have led to the creation of an exciting new field of industrial research. As the need for energy sources increases, efficient methods of preparing coals for specific markets will become more important.

Jan 1, 1979

By Roger K. McLimans

Sphalerite in the ores is multi-banded. Based on color and textures, bands in samples separated by a few kilometers may be correlated. Darkness of color is directly related to iron content. Isotopic and fluid inclusion data indicate that temperatures of ore deposition were 225°C-50°C. The agreement between these two sets of data suggests that chemical and isotopic equilibrium were established. The salt content and hydrogen and oxygen isotopic compositions are similar to present-day values of oil field brines suggesting a similar mode of origin. Ore transport and deposition are not adequately explained by either chloride or bisulfide complexing. Necessarily, other mechanisms were involved.

Jan 1, 1979

By Corate L. Brierley

Low-grade porphyry copper ores containing chalcopyrite as the primary mineral was leached by two strains of acidophilic, thermophilic microbes belonging to the genus Sulfolobus. Leach tests were conducted in glass columns heated to 60-70° C. Pinto Valley and San Manuel ores sized to -1/2 inch + 50 mesh were effectively leached by the thermophilic organisms, but pinto Valley and Cyprus Bagdad ores sized to -2 inch + 1/2 inch resisted leaching. Aeration did not contribute measurably to bacterial copper extraction, since two columns, one inoculated and one sterilized, having a rest/ leach cycle without recurrent aeration exhibited copper extraction patterns similar to those of the aerated columns. Distilled water can be substituted for 9K medium without diminishing copper extraction. Decreasing the pH of the leachate to about 1.8 enhanced the extraction of copper from pinto Valley ore with the thermophilic microbes. Thiobacillus ferrooxidans was found to be relatively ineffective at copper extraction from pinto Valley ore. Of eleven solvent extraction reagents tested, Adogen 364 and Warsol at concentrations of 0.1% and 0.012 were inhibitory to oxygen uptake by the two Sulfolobus strains. Di-2-ethyhexyl phosphoric acid at concentrations of 0.1%, 0.01% and 0.001% were totally inhibitory to the respiration of both organisms.

Jan 1, 1979

By Robert J. Mitchell

A general approach to mine backfill design, including laboratory testing procedures, is outlined in this paper. Relationships between certain design parameters are developed and the effect of other factors is discussed. It is concluded that the inclusion of backfill design calculations at an early stage of mine design can often produce over-all design economies. Not only are the data needed for backfill plant and tailings disposal area design, but also the pillar recovery method and over-all mine stability are dependent on the attainable fill properties.

Jan 1, 1979

By A. S. Romaniuk

More than a decade ago, CANMET management recognized the need to make better use of existing technological information in mining and extractive metallurgy-two fields basic to the economic well-being of Canada. There were at that time no indexes or files dedicated to disseminating technical information for the many minerals mined and processed in Canada, including coal. CANMET, with the nation's largest research and library resources in the minerals field, was in a unique position to fill this need. Initial efforts were concentrated on building a mining file, beginning with identification of world sources of published information, development of a special thesaurus of terms for language control and adoption of a manual indexing/retrieval system. By early 1973, this file held 8,300 references, with source, abstract and keywords given for each reference. In mid-1973, operations were computerized. Software for indexing and retrieval by batch mode was written by CANMET staff to utilize the hardware facilities of EMR's Computer Science Centre. The resulting MINTEC file-one of the few files of technological information produced in Canada-is the basis for the national literature search service in mining offered by CANMET. Attention is now focussed on building a sister-file in extractive metallurgy using the system already developed. Published information sources have been identified and a thesaurus of terms is being compiled and tested. The software developed for CANMET's file-building operations has several features, including the selective dissemination of information and production from magnetic tape of photo ready copy for publication, as in a bi-monthly abstracts journal.

Jan 1, 1979

By V. K. Karra

A mathematical model for the performance of a vibrating screen is developed in terms of an oversize partition curve. This is a normalized curve for any assemblage of particles presented for screening when their size is normalized with respect to the 50 per cent passing size (d50 ) under the prevailing screening conditions. Based on the throughfall aperture (hT) of the wire mesh on the deck, the effects of oversize (% >hT), half-size under (% <0.5 hT), deck location and feed rate were evaluated using the existing screen sizing information. All these variables and also the near-mesh (1.25 hTx 0.75 hT) content (%) of the feed affect the d50. Performance data from different decks of a double-deck screen with various feed rates, size distributions and screen apertures were used to evaluate the near-mesh factor. Effects of wet screening and material bulk density are also incorporated in the model. This generalized model is useful for the simulation of a multiple-deck screen. It furnishes the sieve analysis information of all the deck output streams and therefore has a potential use in the over-all circuit evaluation when used in conjunction with relevant crushing and grinding performance models. An example illustrating the prediction capabilities of the model is given.

Jan 1, 1979

By E. K. Stanek

This volume describes software developed for programmable calculators that is useful in the analysis and design of mine electrical power systems. The programs are equally useful for any industrial or commercial power system. All programs are written for both the HP-97 and the TI-59 programmable calculators. Listings of both versions of the twelve programs that were developed appear in the report. The programs that were developed can be broken into two groups. The first group encompasses design-oriented programs. The second group encompasses analysis programs. For each program the following items are provided: a description of the program&apos;s capabilities, the solution technique used, instructions on how to use the program, a worked out example with data and results and, finally, listings of the programs for the HP-97 and TI-59 programmable calculators. Typical problems that can be attacked with these programs include ground bed design, selection of contactor size, fuse size, relay settings, instantaneous overcurrent trip settings for trailing cables, allowable cyclic cable loading, short circuit analyses, prediction of transient voltages and others.

Jan 1, 1979

By R. Ribeiro

The designers of the new Arafertil concentrator in Brazil provided for complete automatic control of the grinding circuit to meet the operating objective of maximum throughput at a specified grind. Analog control methods were selected because of proven reliability and simple maintenance, and in order to minimize commissioning time and effort. This paper summarizes the step-by-step effort required to progress from local loop control of certain individual parameters to an integrated system capable of achieving the design goal. Emphasis is placed on the practical aspects of commissioning a control system.

Jan 1, 1979

By Michael Kaplan

An investigation was conducted of the use of a mechanical rock splitter as the primary means for rock fragmentation in underground hard rock mining systems. Analyses and scale model tests showed that reasonably sized splitters that could be mounted on the booms of conventional drill jumbos were capable of fragmenting over a ton of rock per cycle. Detailed drill-split mining systems were developed for entry development, room and pillar, bench mining, and cut and fill mining. Economic analyses of these systems showed them to be generally competitive with conventional drill-blast methods. Except for bench mining, drill-split offered substantial cost savings over drill-blast. The investigation also included a technical evaluation of the mechanical splitter, an analysis of health and safety, and a determination of the potential applicability of drilling and splitting.

Jan 1, 1979

The Environmental Session will consist of five papers dealing with various aspects of trace elements associated with coal. Analytical procedures to determine the amounts of trace elements will be discussed. Other papers will deal with trace elements in streams downstream from coal mines, potential pollution from wastes from coal preparation plants, potential recovery of trace elements, and potential pollution from trace elements as a result of the combustion of coal.

Jan 1, 1979

By J. C. Weimer

The goal of Bethlehem&apos;s mining research program is to improve both the safety and productivity of our mines through the use of new equipment, new technology and new mining methods. Although we can all agree on the value of such goals, achieving them can be a costly, time-consuming and sometimes frustrating experience. However, the potential benefits of lower costs per ton and better safety in an increasingly more stringent and confusing regulatory environment make the expended effort worthwhile. At Bethlehem we feel that the mining companies are in the best position to determine the needs of the industry, and coal companies have the incentive as well as mine sites at their disposal for testing. Therefore, the mining industry should be leading the research effort

Jan 1, 1979

By Edgar F. Cruft

It is sometimes said that "mines are made, and not found". I rather doubt that the exploration geologist would be overly sympathetic to that statement, and, of course, like most one-liners it is only partly true. As an explorationist who has been involved in building his own company over the last ten years, and by necessity has become a financier, I can appreciate what real grains of truth are in that statement, however. Because technical people are seldom taught financing in their basic training, and because they are usually not involved in it until at quite a senior level in their careers, the whole field often acquires a certain mystique. The engineering professions have too often believed financing is the province of the accountant or financial executive and just as we in the technical world are often too quick to bristle if the latter try to tread on our domain, the opposite can just as easily be true. Unfortunately, this is another example of a compartmentalized individual, and that is one thing the successful financier cannot be.

Jan 1, 1979

By Donald P. Richards

Is a shaft the same as a tunnel and can it be approached in the same manner for design and construction? The most obvious difference between a shaft and a tunnel is that of orientation; whereas a tunnel is commonly near horizontal or slightly dipping, a shaft is commonly vertical or steeply inclined. As a result, design and construction methods employed for tunneling, in general, cannot be directly applied to shafts, although some of the basic concepts of behavior are quite similar. Many of the shafts that have been sunk in various parts of the world are owned by private mining companies. Each company has generally accumulated years of experience in shaft sinking and mining techniques pertinent to its particular geographic location. When a new shaft is to be sunk or an existing shaft deepened, the tendency often seems to be to continue to use the methods that have been used successfully in the past.

Jan 1, 1979

By Konrad J. Banaszak

At least for the time being, these seems to be general but not universal agreement that Mississippi Valley type ore deposits formed entirely or in major proportion from heated connate brines (e.g. 1) Even with that agreement, major questions remain. I will present a coherent geochemical model and look at alternative views in the context of that model. The pattern of the following discussion is 1) the general geochemistry of the ore fluid, 2) the density-temperature relations and possible mechanisms of flow of those fluids, 3) the mechanisms of transportation and deposition of the ore minerals, and 4) a summary of a coherent model of genesis. The data equivocally define much about the deposits. The answer is still elusive.

Jan 1, 1979

By Christopher Haycocks

Because of growing pressure from government and consumers to produce more coal, the mining industry must improve existing techniques and devise more efficient mining methods. Mining of the thicker, shallower and geologically superior coal seams in the western United States is being subjected to increasing pressure from environmentalists; and so in order to meet the demand, the coal industry is exhausting the more accessible surface seams and beginning to mine seam of over 1,000 feet in depth and less than. 30 inches in thickness. The longwall mining system is the natural choice for extracting deep and thin coal seams, as it operates almost independently of the overburden rock stress. Due to the added fact that longwall mining is an inherently more productive method than room and pillar mining, many coal producers are looking to it as a means of increasing productivity without a corresponding cost increase. The consistent rise in application of longwall mining in the United States in the last decade illustrates the excellent potential of this technique for the future. American mining conditions are geologically different from those in Europe where longwall mining has been highly developed and extremely successful. Although numerous successes have been recorded in the U.S. with this mining system, a substantial number of failures have also occurred. These failures are due primarily to roof control problems usually over the face, in the tail entry, or both. Another problem area for American operators contemplating the use of this method has been correct selection of equipment, which should be custom fitted to local mining conditions for optimum productivity. It is essential that correct estimates for chock resistances, support densities, supported and unsupported roof spans, as well as rates of advance and length of working faces be provided to optimize mining conditions. Unless extensive pilot projects are planned engineers must choose their equipment correctly at the outset. A typical investment in longwall equipment will amount to several millions of dollars.

Jan 1, 1979

By W. I. Nissen

This Bureau of Mines report presents the design for a commercial-sized flue gas desulfurization (FGD) demonstration plant that uses the citrate process. The goal of the Bureau&apos;s citrate process is to minimize the undesirable environmental impacts of industrial plants emitting SO2-bearing gas. The FGD plant is located at the George F. Weaton powerplant, Monaca, Pa. Construction was completed in April 1979 and will be followed by preliminary testing and a 1-year testing and evaluation program. Design capacity of the FGD plant is 156,000 scfm of 0.2-volume-percent-SO2 flue gas yielding about 16 tons of sulfur per day. The plant is intended to (1) clean fly ash, SO2, and Cl- from the gas while cooling the gas in a venturi scrubber, (2) absorb SO2 from the gas using 1,200 gpm of a countercurrent-flowing citric acid-sodium citrate-sodium thiosulfate solution, (3) react the absorbed SO2 in two 13,000-gal stirred closed vessels with added H2S, thus precipitating elemental sulfur and regenerating the citrate solution for recycle, and (4) recover the sulfur from the slurry by air flotation, followed by melting in a heat exchanger and separation from the occluded citrate solution in a sulfur decanter at 35 psi and 135° C.

Jan 1, 1979

By Leo J. Vogel, E. D. Hummer, David J. Akers

INTRODUCTION An efficient refuse-disposal system is a necessary part of the modem cleaning plant. The large-scale refuse system and disposal area, engineered for the lifetime of the plant, has become more important due to the greater tonnages of refuse produced from increased quantities of mechanically mined and prepared coal. Laws and increased government regulations have affected the design and operation of disposal systems. THE EFFECT OF MINE AND PLANT OPERATION Refuse disposal starts at the mining face. The mining system, the type of roof support, the machinery used, and the degree of discipline at the face contribute to the amount and type of refuse that must be removed through the disposal system. Economies gained through modification of the mining system or mining machinery may be partially offset by increased dilution of the mined coal with impurities from associated rock formations. In some cases the change in the mining system and equipment has reduced the dilution. In all cases the ratio of impurities that must be removed from the raw-coal feed to the plant not only affects the maintenance and

Jan 1, 1979