Search Documents

During the period 1979 thru 1982, Multi Mineral Corporation conducted a mining research program at the United States Department of the Interior's Bureau of Mines Oil Shale Mining Environmental Research Facility in the Central Piceance Creek Basin, Rio Blanco County, Colorado. The program consisted of mining, environmental and geotechnical research data and the results are described in this report.

Jan 1, 1983

By D. D. Runnells

This study focused on the chemical reactions between uranium tailings fluids and cores of subjacent bedrock from the site of the Cotter Corporation uranium mill at Canon City, Colorado. Actual and synthetic tailings fluids were forced through cores of bedrock. The pH of the effluent solutions was the dominant control on the behavior of dissolved species in solution. The pH depended on the presence or absence of calcite cement in the rocks. Calcite neutralized acidic raffinates and caused the precipitation of iron, manganese, aluminum, and possibly uranium. Chloride, sulfate, and sodium were not retarded upon passage through the cores, and sulfate and chloride should be useful as tracers of escaping tailings fluids. Zinc, copper, cobalt, nickel, uranium, and vanadium exhibited high mobility under acidic conditions and were strongly retarded at elevated pH. Calcium was released due to dissolution of calcite and ion-exchange. Magnesium was not retarded in concentrated solutions, but showed moderate retardation in dilute fluids. Potassium and ammonium both showed early retardation followed by breakthrough and mobility. The behavior of molybdenum was strongly dependent on pH, with retardation at low pH and mobility at elevated pH. Selenium was highly mobile under all conditions. Selenium should be a better tracer than molybdenum for many situations. Precipitation of carnotite appears to control the solubility of uranium and, possibly, vanadium. With the exception of the precipitation of aluminum and silica, all reactions were rapid.

Jan 1, 1983

By George A. Costello

A theoretical analysis is presented for the static and dynamic response of wire rope in deep-shaft mining operations. Expressions for the stresses in the individual wires of complex wire ropes are derived, and specific results for simple strands, 7x7 ropes, 6x 19 Seale ropes both with and without internal-wire-rope cores, and 6x25 filler-wire ropes both with and without internal-wire-rope cores, are presented for the case of ropes subjected to a combination of axial loading and bending over a sheave. Consideration is also given to the dynamic overloading associated with certain mining operations, such as dumping ore into a suspended skip and accelerating a fully loaded skip upward. Experiments to determine the axial stiffness of wire rope are described. Factors affecting the service life of wire rope, such as residual stresses, contact stresses, and fatigue behavior, are discussed. Specific research areas in need of further investigation are identified.

Jan 1, 1983

During the period 1979 thru 1982, Multi Mineral Corporation conducted a mining research program at the United States Department of the Interior's Bureau of Mines Oil Shale Mining Environmental Research Facility in the Central Piceance Creek Basin, Rio Blanco County, Colorado. The program consisted of mining, environmental and geotechnical research data and. the results are described in this report.

Jan 1, 1983

By Russel R. Bohn

The objectives of this study were to: (a) determine the state of the art for the control effectiveness of various chemical dust suppressants, (b) field test the effectiveness of the dust suppressants, and (c) develop technical guidelines for selecting and implementing cost effective tailings pond dust control programs. Chemical stabilizers evaluated under field conditions were: Coherax, Calcium Lignosulfonate, Nalco 656, 655, and Magnesium Chloride. Testing in the field utilized a portable field in-situ wind tunnel. The wind tunnel was placed on the tailings surface and simulated wind speeds of up to 80 mph were used to determine wind erosion threshold velocities. Emission rate testing was performed with the wind tunnel through the use of a real-time cascade impactor. A control cost effectiveness evaluation was performed to determine how efficient the chemical stabilizers were on a dollars expended per acre basis.

Jan 1, 1983

By Robert Torbin

The objectives of the Continuous Shaft Lining (CSL) System are to reduce the costs, safety hazards, and time currently required in lining mine shafts with concrete. The CSL will line machine bored shafts downward from the shaft collar on a continuous basis using an inverted, pressurized slipforming technique. The technique for slip-forming downwards has been demonstrated and refined under this program. The approach taken involved laboratory scale testing of key features of the CSL concept. These feature tests included concrete distribution, concrete sealing, concrete slipforming and development of a reliable concrete mix. Based on these results, a full scale above-ground test facility and CSL were designed and fabricated. The objectives of these tests were to demonstrate the viability of the basic concept; to establish operating limits; and to provide input data and information for the design of a second generation shaft lining system. The results of the program have led to a CSL design and operational philosophy which will need to be tested in an underground environment before industry will accept the technology. However, the next generation CSL promises to meet all the original program technical objectives.

Jan 1, 1983

By Robert Torbin

The objectives of the Continuous Shaft Lining (CSL) System are to reduce the costs, safety hazards, and time currently required in lining mine shafts with concrete. The CSL will line machine bored shafts downward from the shaft collar on a continuous basis using an inverted, pressurized slipforming technique. The technique for slip-forming downwards has been demonstrated and refined under this program. The approach taken involved laboratory scale testing of key features of the CSL concept. These feature tests included concrete distribution, concrete sealing, concrete slipforming and development of a reliable concrete mix. Based on these results, a full scale above-ground test facility and CSL were designed and fabricated. The objectives of these tests were to demonstrate the viability of the basic concept; to establish operating limits; and to provide input data and information for the design of a second generation shaft lining system. The results of the program have led to a CSL design and operational philosophy which will need to be tested in an underground environment before industry will accept the technology. However, the next generation CSL promises to meet all the original program technical objectives.

Jan 1, 1983

By Raja V. Ramani

The potential usefulnuss of reclaimed surface-mined land has received much attention in recent times. This attention is partially due to the establishment of federal environmental reclamation standards but concern for achieving better land uses has also been shown by interested members of the mining industry. In an effort to develop a procedure for evaluating postmining land use potentials, specific mines in various regions of the U. S. were studied to determine the extent of current mined-land planning and to discover characteristics that are regional in nature. As part of this investigation, a 430-acre surface mine in Clear-field County, Pennsylvania has been studied. Established site planning principles have been applied to the case study site including formation of a data base, development of alternate land use plans, and evaluation of the economic, environmental, and social impacts of the land use alternatives. Key factors affecting site realization have been identified along with positive suggestions for applying land use planning processes to mined-land planning.

Jan 1, 1983

By Sandip K. Mukherjee

This report presents the results of the economic analysis of several applicable alternatives to increase airflow in four underground coal mines. Pressure-quantity surveys were conducted underground and measurements were also made at the main mine fan(s). The existing ventilation networks were modeled using the modified Penn State ventilation simulator. The applicable alternatives were simulated. Performance data obtained from these simulation runs were utilized to conduct the cost-effectiveness analysis. The costs for each of the alternatives included capital, operating and maintenance costs. These costs were expressed as annual ventilation costs per active section in terms of dollars per elm taking into account the economic life associated with each of the alternatives. The benefits were expressed as increased airflow quantity in the critical sections. A section of this report also deals with comparison of simulator predicted air quantity values against air quantity values measured underground. The computer outputs for each simulation run are presented in Volume II of this report.

Jan 1, 1983

By Richard Rittenhouse

This program was to develop a new base line system for automated continuous room and pillar type mining. The primary requirement estab¬lished for this machine is that the machine be capable of mining and bolting simultaneously. Additionally, this machine was to provide temporary and permanent roof control, have a productive - full - face semi-automatic mining system, leave a clean entry outby the machine, provide maximum operator protection, provide effective dust suppression and provide air scrubbing to restrict respirable dust to permissible levels. The machine has effectively demonstrated the ability to mine and bolt simultaneously. Additional above ground operation, testing, and time studies are recommended to further verify the machines abilities. Design improvements are recommended for future generation AES machines. These relate to marginal design areas such as side loading on vent duct lift cylinders, etc., that will not impair additional testing of the existing machine.

Jan 1, 1983

By Ronald Branstetter

Gaseous and particulate exhaust emissions from 20 diesel engines in service at five underground mines were measured with high accuracy instrumentation. The engines that were tested were checked for faults or maladjustments. The vehicle and engine maintenance organization was studied at each mine and an idealized maintenance program was devised. Faults were induced in a new diesel engine to determine their effect on the characteristics of the exhaust emissions. The results, conclusions and recommendations from this investigation are presented in this final report.

Jan 1, 1983

By N. Barton

Large scale tests were conducted on quartzitic gravel and crushed sand-stone to investigate pertinent geotechnical properties for backfill support of egress shafts. Such shafts are envisaged for rapid launching of deep-based missiles. The backfill support is designed to resist shaft closure under dynamic loading, and must also drain rapidly to a lower catch chamber to allow launching. Large scale tilt shear tests were performed to measure the internal shear strength of the two backfill materials. Shaft filling and emptying tests were conducted in a 12 ft deep, 3 ft diameter model section of shaft drilled in sandstone. One half of the model was smooth bored, the other half rough-surfaced to represent drill and blast surfaces. Vertical and horizontal pressure cells indicated that stress only built-up during the first 1 to 1 ½ diameters of filling, due to the high-sidewall friction of 38° for the rough shaft and 31° for the smooth shaft. Interface sliding tests were performed to confirm these figures. Static and dynamic deformation tests were also per-formed, and indicated moduli as high as 56,000 psi, which will give excellent shaft support. Both the shaft support characteristics and the ease of emptying of gravel look particularly promising.

Jan 1, 1983

By Donald James Butler

Problems resulting from underground mines in three inactive mining districts in Colorado were investigated. The purpose was to determine how these problems could be reduced or eliminated in new closings -- essentially by benefitting from lessons of the past. Mines in Leadville, Westcliffe and the Cripple Creek-Victor districts were evaluated. Two basic types of problems were found to exist in the districts: environmental degradation and hazardous conditions. Environmental problems result largely from acid and toxic drainage from the runes and from leaching of surface waste rock piles and mill tailings impoundment. The acid drainage contributes high levels of metals to streams and deposits sediment in the stream bottoms. Erosion of waste piles is a lesser problem. Hazardous conditions from open or improperly sealed mine shafts and adits, mine subsidence pits, and from deteriorating and unsafe surface structures are common to the three districts. These problems become worse with the ravages of time and vandalism. Engineering solutions which would correct or reduce many of these problems are presented. These recommendations should also be applied to new mine closures, however, more basic changes are needed to effectively implement improved mine closures. The changes must take place in the areas of legislation, mining practices and education. Legislated regulations should realistically reflect the needs of both the mine operators, protection of the environment and the best interest of the general public. Benefits should be provided for compliance with regulations instead of penalties being assessed for noncompliance. Hazardous conditions and environmental problems associated with mines can be alleviated through improved mine design and effective cloning procedures. Education should provide an appreciation by the general public of past and present problems facing mine operators. This will result in an improved mining climate which, in turn, will insure a continuing supply of minerals to meet increasing needs.

Jan 1, 1983

By J. O. Merritt

The primary objective of this research program was to recommend ranges of minimum luminance for safety in underground metal and nonmetal mining. Visual tasks critical to safety were identified and rank-ordered. Realistic, full-scale, dynamic task simulations encompassing the most important visual components of the critical tasks were installed in a large simulated workspace. Five trained observers performed the six simulated mining tasks under varying levels of luminance. Over 13,000 measurements of visual task performance were used in developing minimum luminance recommendations for the on-foot underground worker and the mobile equipment operator.

Jan 1, 1983

By C. Haycocks

The problems caused by interaction in multi-horizon mining are world wide and are not limited to the coal industry. These problems will continue to increase as mining of new seams multiplies and replaces production from mined out horizons. Interaction problems are particularly evident in the Appalachian coal fields which contain many mineable, contiguously placed coal seams. Selection of the mining sequence of these seams, historically and currently, is based primarily on considerations of seam ownership, availability, and economics. Experience has shown, however, that mining any seam can seriously affect subsequent operations in coal seams both above and below the one being mined. This interaction effect is often detrimental to the recovery cost and safety of mining the subsequent seams. Designing to avoid or minimize interaction effects represents a major challenge to the modern coal mining industry and therefore is the focus of this research. In an effort to evaluate past interaction effects and provide guidelines for future mine design, interactive ground control problems were categorized into four areas. These are pillar load transfer, massive interseam shearing, subsidence and pressure arching effects. To facilitate research, each of these areas was studied separately although in reality these subdivisions are arbitrary and have considerable overlap.

Jan 1, 1983

By Koehler Stout

Previous work done by the authors of this report indicates that hydraulically-placed backfill can be strengthened several fold by various placement methods. Sunshine mill tailings were tested by these placement methods and strength increases up to thirty times were achieved over the ordinary placement methods. A computer simulation study of the test stope in the Sunshine Mine showed that a high-modulus fill absorbs up to 27% of normal stresses versus 7% for "normal" fill while reducing maximum convergence 28% versus 8% for "normal" fill. Although high-modulus fill was not placed in the test stope during this contract, various instrumentation was purchased, designed and built to record necessary data in the stope. Stress gauges were placed in the pillars and recorded data corresponded quite closely with theoretical projections.

Jan 1, 1983

By Ronald Branstetter

Gaseous and particulate exhaust emissions from 20 diesel engines in service at five underground mines were measured with high accuracy instrumentation. The engines that were tested were checked for faults or maladjustments. The vehicle and engine maintenance organization was studied at each mine and an idealized maintenance program was devised. Faults were induced in a new diesel engine to determine their effect on the characteristics of the exhaust emissions. The results, conclusions and recommendations from this investigation are presented in this final report.

Jan 1, 1983

By Mark R. Pettitt

The development of fire hazard criteria for noise control products in underground coal mines are presented. Qualifying requisites of the criteria include maintaining miners' safety, allowing for maximum use of noise control products, and economic feasibility. The burning process is analyzed for its relationship to fire hazard criteria developed by NASA and the FAA, and the mine environment is analyzed in conjunction with the end-use applications of noise control products. Also, the interim fire hazard specification developed by MSHA is appraised as it applies to end-use applications of noise control products. From these analyses and a literature survey, fire hazard criteria are developed. They include an initial screening procedure that evaluates the level of flammability testing required. Fire tests that may be indicated are the Vertical Flame Test, the Ignition Temperature Test, and the 25-Foot Tunnel Test.

Jan 1, 1983

By Piyush K. Dutta

This report describes the design, development and manufacture of production stoper drills and results of their field tests, it is shown that underground stoper drill noise level can be reduced from 118 dBA to below 100 dBA by using these pneumatic drills. The design concept of these drills is a radical departure from the standard valved rifle bar type drill machine design to a drill featuring a valveless independent rotation system, use of an integral muffler and a shroud tube. Six drills were manufactured in a standard commercial drill manufacturing setup and organization. The design and production technology proved that commercially viable quiet drills can be made available for mine use.

Jan 1, 1983

By Alice M. Chieruzzi

This Country Documentation Report presents the development of economic indices for the Philippines for the period from 1970 through 1981. The work was done through the Bureau of Mines, Minerals Availability Program, under Contract number J01225001. This contract calls for the development of twelve index time series describing factor input costs in the mining sector of 95 countries. The twelve index time series describe the costs of: 1) mining wages, 2) construction wages, 3) equipment and repair parts, 4) bits and related steel, 5) eimber and lumber, 6) fuel, 7) powder and balsting agents, 8) tires, 9) construction materials, 10) industrial materials, 11) transportation, and 12) electrical power. These indices combined with weight factors being developed by the personnel of the Minerals Availability Field Office (MAFO) of the Bureau of Mines in Denver, Colorado, will be used to perform instantaneous updates of all costs relating to the mining industry. The indices were developed primarily for use in the Bureau's Minerals Availability Program in assessing the worldwide availability of nonfuel minerals.

Jan 1, 1983