Search Documents

By L. Salnais

"Aluminum alloy structural components f or aircraft designed prior to the early 1970s, were machined from 2024, 7075 and 7079 plate, bar and forgings in either the T3xxx of the T6xxx tempers. Protective treatments for these parts consisted of chromic acid anodizing and alkyd zinc chromate primer, plus a nitrocellulose lacquer for exterior parts.The major service problem with these parts was the frequent occurrence of exfoliation corrosion and stress corrosion cracking (S. C. C.). Therefore, 2024 and 7079 alloys, with min or exceptions, were not used in aircraft designed after the early 1970s. Replacement materials were 7075 and 7050 alloys in the overaged, exfoliation corrosion and S. C. C. resistant, T73xxx tempers.The use of improved materials together with the upgrading to chromated epoxy primers, polyurethane enamels and the introduction of water displacing corrosion inhibiting compounds have significantly reduced corrosion in aircraft. IntroductionThe prevention of corrosion in aircraft has been a challenge to aircraft designers for many decades. With the design of the first all-metal aircraft, the designer and builder were thrust into the relatively new field of protective treatments as corrosion started to become more prevalent. This resulted from the continually increasing importance and wider utilization of aircraft, and their exposure to a wider variety of ho stile environments such as urban industrial pollution, high humidity tropical areas and salt ladened marine environments.Corrosion advanced another significant step when, after World War II, designs of new and larger aircraft utilized larger and thicker metal sections in the manufacture of structural components. With thicker mill products came higher residual heat treat, fabrication and assembly stresses resulting in an increased number of stress corrosion and exfoliation corrosion problems.Apart from the exterior environment, aircraft interior s can be exposed to a number of fluids which are either directly or indirectly responsible for corrosion. The most common of the fluids is water which is usually introduced as a result of condensation, especially in pressurized fuselages, and spillage from lavatories, galley s and electrolytes from batteries. These fluid s have a degrading effect on protective treatments and are also corrosive to the substrate metal. Fluids such as phosphate ester hydraulic fluids and ester based turbine engine lubricating oil s are not corrosive to the substrate metal, albeit they do contribute to corrosion by the degrading effect on protective treatments."

Jan 1, 1988

By M. Geoghegan

Under the provisions of the U.N. Law of the Sea Convention Ireland is likely to have mineral rights to an area of continental shelf some six times its present land area. Apart from the major potential hydrocarbon basins which are currently the focus of active commercial exploration, little is known about the mineral resources of this vast area. In recent years a variety of mineral resources however have been identified from the coastal region. These include Sand and Gravel aggregates, Calcaraeous Algae (Lithothamnion), Heavy Mineral Sands and Coal deposits. The potential also exists in the coastal zone for buried placer deposits and base metal deposits. Several million cubic metres of gravel and hundreds of millions of cubic metres of sand have been identified by the Geological Survey of Irelands (G.S.I) Marine Unit off the east coast. The greater part of these deposits lies within the 10 metre depth contour and are easily recoverable. Irish aggregate needs at present are well supplied by onshore Pleistocene glacial deposits. Commercial interest in offshore deposits is in supplying coastal areas which are locally poor in aggregate and major coastal construction works. The possibility of supplying the large British and Continental European Market nearby also exists.

Jan 1, 1988

By W. Petruk

A study was undertaken to determine whether interrelations between mineral grains affect ore breakage during grinding, and to establish a correlation between ore breakage and mineral liberation. A base metal ore from the Brunswick No. 12 deposit in New Brunswick was ground for different periods of time in a laboratory ball mill, and both the unbroken ore and the ground products were analysed by image analysis. The results show that the mode of breakage is strongly influenced by the behaviour of pyrite. Similar size distributions were obtained for material from the 15 minute grind in a laboratory ball mill, for the grinding circuit discharge from a commercial mill, and for pyrite grains in the unbroken ore. This similarity indicates that a 15 minute grind breaks poorly bonded pyrite grains along grain boundaries, and represents the limit of easy breakage for the ore. Such a grind liberates both large separate grains of ore minerals and poorly bonded mineral grains that occur in interstices among pyrite. On the other hand the 15 minute grind does not separate moderately bonded mineral grains nor release moderately bonded interstitial minerals from pyrite; a 45 minute grind in a laboratory ball mill is required. It is assumed that, for Brunswick No. 12 ore, a 45 minute grind in a laboratory ball mill is equivalent to regrinding in a commercial mill. Grinding beyond 45 minutes in a laboratory ball mill breaks the ore by fracturing pyrite across grain boundaries and by chipping grain edges. Such intense grinding does not markedly increase sphalerite liberation from Brunswick No. 12 ore, because most of the sphalerite that can be released was liberated at the 45 minute grind. In contrast the intense grinding increases galena liberation because a significant proportion of the galena occurs as minute inclusions in pyrite. These findings show that ore breakage and coincident liberation depend upon size distributions, intergrowths, and mode of occurrence of the minerals in an ore.

Jan 1, 1988

By K. Y. Haramy

Coal mine bumps involve the violent, rapid failure of coal and rock around a mine excavation. Deep coal mines with strong roof and floor rocks and high-stress conditions frequently experience face and rib bumps. The bump problem is becoming more severe as mining depth increases, prompting efforts to control high stress in advance of mining. This Bureau of Mines report presents a review of the most widely used methods to detect and destress high-stress zones along coal faces and an investigation of stress-related bump problems and destressing techniques at a cooperating mine. Geotechnical instrumentation and microseismic methods were used to better understand bump occurrences in underground coal mines. Laboratory tests of the drilling-yield method for high-stress detection were conducted to determine the correlation between the volume of cuttings obtained and the magnitude of the applied stress at various confining pressures. A three-dimensional, multiple-seam computer modeling program, MULSIM, was used to evaluate the effectiveness of stress-relief methods. Modeling results indicate that dangerously high-stress areas can be controlled by either proper planning or destressing. Proper mine planning guidelines and destressing methods such as volley firing, hydraulic fracturing, and auger drilling are discussed.

Jan 1, 1988

By Y. C. Kim

Although the first published optimum pit limit design algorithm by Lerchs-Grossmann dates back to 1965, the majority of the open-pit mines in the U.S. has not as yet adopted such a rigorous optimization algorithm. Instead, the floating cone approach initially developed by Kennecott Copper in 1961 is still used today for various reasons. However, shortcomings with the floating cone algorithm, particularly for precious metal deposits with erratic mineral distributions, have provided a renewed interest in optimizing algorithms.

Jan 1, 1988

By Susanne Pignolet-Brandom

QEM*SEM is an automated scanning electron microscope/computer system that characterizes samples with regard to mineral modal abundances, mineral grain and particle sizes, mineral associations, and particle surface areas. Additional information, based on the classification of particles according to the area percentage of a mineral of interest, can be obtained for samples of particulates. QEM*SEM is capable of analyzing a wide variety of materials although it was originally developed for applications to the minerals industry.

Jan 1, 1988

By R. J. Fantel

The Bureau of Mines investigated the resources, costs, capacities, market relationships, and short- and long-run supply of phosphate rock and phosphoric acid. The 206 mines and deposits evaluated in 30 market economy countries contain an estimated 35.1 billion mt of recoverable phosphate rock (demonstrated resource level). U.S. resources are sufficient to satisfy the domestic and export markets for phosphate products well beyond the year 2000. Because of resource depletion at current producers, however, new properties (with higher cost levels) need to be developed if U.S. production levels are to be maintained. Existing worldwide capacity can satisfy expected demand through the early 1990's. Expansion at existing mines or low demand growth could mean that no new property development will be needed before the late 1990's. Worldwide, almost $8 billion could be required for development of new phosphate rock properties between now and the year 2000, given 3-pct annual growth in demand. Most properties that could develop in the 1990's would require price increases of 20 to 50 pct to break even. To earn a 15-pct rate of return on investment, prices must rise to nearly double the present level of $24 to $29 per metric ton.

Jan 1, 1988

By J. A. Herbst, Z. Rogovin, Lo. Y. C., K. Rajamani

Knowledge of the amount of time material spends in a continuous mill in a closed grinding circuit is essential for circuit performance analysis and scale-up design. A convenient method for acquiring this information involves the use of pulse tracers in residence time distribution (RTD) experiments. In typical grinding circuit experiments, RTD measurements are done by injecting a pulse tracer into the mill inlet and detecting it in the circuit exit. In this article, an easy mathematical method for calculating mean residence time and the degree of mixing of material in a mill present in a closed grinding circuit is developed. There are no restrictions on the location of the tracer injection or detection points with this method. Any convenient location in the circuit can be chosen without affecting the residence time distribution measured. The analysis of impulse response data obtained from several commercial grinding circuits using this method is presented.

Jan 1, 1988

The objective of this study was two-fold: 1. To perform a world literature search pertinent to the analysis, selection and design of hoisting systems and their components and to codify the search into a literature compendium. The search resulted in a technical data file of over 1500 hard copy items. The compendium index was also suitable for establishing a comprehensive computer-loaded data base on the subject. 2. To develop a comprehensive system of guidelines to cover salient aspects of analysis, selection and design of electrical, mechanical and structural components of a hoisting system with a view to establish parameters for maximum safety and efficiency of operation, installation and revision of the system. 3. (a) The system design of hydrostatic drives for mine hoists, usually of special nature, is considered along with oil hydraulic component selection suitable for the application; (b) The criteria for head frames of steel and/or concrete are developed with full consideration of all operating and environmental conditions.

Jan 1, 1988

The objective of this study was two-fold: 1. To perform a world literature search pertinent to the analysis, selection and design of hoisting systems and their components and to codify the search into a literature compendium. The search resulted in a technical data file of over 1500 hard copy items. The compendium index was also suitable for establishing a comprehensive computer-loaded data base on the subject. 2. To develop a comprehensive system of guidelines to cover salient aspects of analysis, selection and design of electrical, mechanical and structural components of a hoisting system with a view to establish parameters for maximum safety and efficiency of operation, installation and revision of the system. 3. (a) In-shaft equipment design and specification criteria are considered as they influence guideline preparation. (b) A comprehensive review of hoist electric drives and controls as applied to mine hoists is set forth with special reference to duty cycle calculations and their effect on electrical component selection.

Jan 1, 1988

By Les A. Beckett

The Bureau of Mines has developed MULSIM/BM, an improved computer program using the boundary-element approach for geomechanical analysis of mine plans in single or multiple coal seams. This Information Circular presents the improved features of the MULSIN/BM program. The four major improvements are the following: (1) Ability to specify up to 26 material property sets. (2) A new material model capability for gob and inserted materials such as packwalls or cribs. (3) Ability to model a large area with a grid of undivided blocks and to subdivide only a specified fine-mesh portion of these blocks into elements. (4) Specification of extraction ratios for the undivided blocks. In addition, an interactive graphics mesh generator program was written to accompany MULSIM/BM. A complete user's guide and program listings are included within the appendixes. The MULSIM/BM and mesh generator programs are available on tape from the National Technical Information Service.3

Jan 1, 1988

By Victor V. Verbinski

This report presents the development of a raw coal concentration sensor for hydro-transport of coal and refuse (rock) from underground mines, and the results of an international test series carried out at the Colorado School of Mines Research Institute in Golden, Colorado, the U.S. Bureau of Mines, Hydraulic Transport Research Facility in Pittsburgh, Pennsylvania, Saskatchewan Research Facility in Saskatoon, Saskatchewan, Canada, and the Steinkohlenbergbauverein Test Facility in Essen, West Germany. Test results are presented for a three-component sensor and also for the more rugged two-component (all nuclear) sensor.

Jan 1, 1988

The wealth of a nation may be measured in many ways, but one of the most important is its natural resources, particularly its minerals. Minerals create the wealth upon which economic prosperity and defense preparedness rest. Managing mineral resources for the benefit of all Americans continues to be an important national goal. In its 78-year history the U.S. Bureau of Mines has established itself as the world's premier mineral information and research agency. Its authoritative, comprehensive data and pioneering research have contributed significantly to a strong U. S. mineral position in the world.

Jan 1, 1988

By G. L. Bartlett

"INTRODUCTION The major objective of our research is to help reduce the incidence and severity of coal worker's pneumoconiosis (CWP). To that end, this project is designed to improve our understanding of the processes that lead to pulmonary dysfunction following mine dust exposure, and how those processes might be interrupted or attenuated. The response of the lung ' to inhaled particles is complex, and the course of development of disabling CWP is slow and unpredictable. From among the numerous cellular and molecular interactions involved in the pulmonary response to inhaled particles, this project is focussed on the role that the pulmonary alveolar macrophage (PAM) may play in regulating the activity of fibroblasts.The PAM is the lung cell that has the most immediate and the most obvious interaction with inhaled particles. Within a short period after particles are arrested in the alveolus of the lung, they are phagocytized (engulfed) by these specialized cells. The PAM then has a diverse potential repertoire of subsequent activities. Which reaction actually ensues is determined, in large part, by the nature of the phagocytized _particles. Activated PAMs produce a variety of products that may affect adjacent lung tissue, including superoxide free radical, elastase, collagenase, prostaglandins, platelet activating factor, etc. Those may well be important in the pathogenesis of CWP, but they are beyond the scope of this project. Background information that is cogent to this project has come primarily from investigations using animal models of silicosis and asbestosis. PAMs that have ingested silica particles synthesize and release molecules that control the behavior of surrounding cells. One such mediator is interleukin-1 (IL-1), a molecule that plays a central role in many aspects of the response to injury. It can stimulate fibroblasts (the cells that help to hold tissues together) to release the enzyme collagenase, resulting in breakdown of the structural collagen fibers that support the lung tissue. IL-1 also stimulates fibroblasts to undergo mitosis and to proliferate, which is an initial stage of fibrosis. Certain stimulants cause PAMs to release fibroblast growth factors (FGFs) that are distinct- from IL-1. Under other circumstances activated PAMs synthesize and release molecules that stimulate fibroblasts to accelerate synthesis of collagen fibers, thus contributing to fibrosis. Although these observations provide a valuable precedent for analysis of the mechanisms involved in CWP, their relevance to CWP cannot be assumed since most of those studies involved macrophages or fibroblasts obtained from tissues other than the lung, and because almost none of them have used CMD as the stimulating particles. Therefore, the goal of this project is to learn how exposure to CMD affects the behavior of PAMs, and in turn how products of dust-exposed PAMs affect fibroblasts and the process of fibrosis in the lung."

Jan 1, 1988

By Robert G. Bottge

The Bureau of Mines has engaged m a program to determine the availability of land for mineral exploration and development in Alaska. Land availability, based on ownership and Federal and State laws and policies, is compared with mineral terranes and mineral deposits. This is the fifth of six regional studies, which cover the State with a comprehensive set of maps and data compilations. This study covers an area of 112.3 million acres in western Alaska. In July 1986, 41.0 million acres, 37% of the study area, were available for mineral exploration and development; 14.6 million acres, 13%, were available with restrictions; and 56.7 million acres, 50%, were unavailable. Nearly 65% of the unavailable land is classified as national parks, preserves, wildlife refuges, and wild and scenic rivers. Of the 34.0 million acres of mineral terranes that underlie the study area, 12.9 million acres, 38%, are available for exploration and development; 3.6 million acres, 11%, are available with restrictions; and 17.5 million acres, 51%, are unavailable.

Jan 1, 1988

By Robert J. Evans

The Bureau of Mines is sponsoring a variety of long-term, high-risk research to advance state-of-the-art technology in U.S. underground coal mining. This report reviews the status of many Bureau projects that support fundamental underground coal mining operations; the project areas include cutting coal from the solid (extraction), hauling coal from the face (transport), and activities that sustain daily operations (logistics). Innovative equipment and technology have been developed, with these major objectives: to significantly improve coal mine productivity, to further advance coal recovery and personal safety within the mining industry, and to reduce the time needed to develop longwall panels. The majority of the prototype equipment covered in this report either has undergone or will undergo comprehensive evaluation at Bureau surface test facilities so that performance and reliability can be improved before the equipment is tested and evaluated in a working section underground.

Jan 1, 1988

This report is a proceedings of a briefing recently sponsored by the Bureau of Mines at which Bureau personnel presented findings from their research efforts to improve steelmaking techology currently used in the United States. The papers contained in this report address many areas of concern to the iron and steelmaking industry. Among these are improving arc stability in electric arc furnaces, preheating ferrous scrap to reduce energy consumption, fluorspar substitutes in steel-making, basic steelmaking refractories, corrosion of iron-based materials, improvements in stainless steel acid pickling processes, recycling of stainless steel dusts and other wastes, and use of wastes as a source of zinc for electro/galvanizing.

Jan 1, 1988

By Henry P. Cole

A series of studies are described that identify critical health and safety skills needed by underground coal miners for coping with mine emergencies. First aid and self-rescue and escape were selected as two broad performance domains that include many subordinate skills needed for preventing, recognizing, and coping with mine emergencies. The performance domains and their objectives were used to direct the development of simulation exercises that permit miners to experience mine emergencies in the safety of a training room. The exercises are based upon research with similar simulations for the training of flight crews and medical personnel in information gathering, judgment, and decision making skills. Exercise content is drawn from actual mine accident and disaster case studies. The exercises incorporate recent principles of cognitive psychology and instructional design. Initial studies in annual refresher training classes suggest the exercises are stimulating for miners and their instructors, easy to use and read, sufficiently complex and authentic to challenge experienced miners, and useful devices for both teaching and testing critical problem solving skills required for preventing and minimizing emergencies.

Jan 1, 1988

By Henry P. Cole

A comprehensive review of published research was carried out to identify methods for teaching and assessing critical but nonroutine skills needed for coping with emergency situations. Specific methods for assessing critical skills proficiency in aviation, medicine, organization management, the military, and other industrial/technical workplaces are described. The potential application of these methods for teaching and assessing (1) critical first aid and (2) self-rescue and escape skills to underground coal miners in annual refresher training is explored. Research and development activities that may improve mine health and safety training are suggested. Most of these research and development activities were completed later in the project. This additional work is reported in the project technical report #2 and the final report. The research reported in the present document was completed in 1984 -85. Many of the initial findings reported in this document are updated in the later project final report.

Jan 1, 1988

By Mark S. Sanders

There is a growing awareness among mining professionals that the human factor plays a significant role in safety and productivity. Since the 1960's, the science of human factors, or ergonomics, has been making inroads into the mining industry, and a considerable amount of research has documented human-factor-related mining problems and solutions. This Bureau of Mines report is directed toward summarizing the application of human factors to improving safety, productivity, and the general physical and psychological working conditions of miners. The aim of this report is to familiarize the readers with the role of human factors in the mining industry and the benefits that can accrue by systematically applying available human factors principles and data. The text contains 10 chapters dealing with human, equipment, and environmental factors. Each chapter builds on the previous chapter; therefore, it is recommended that the chapters be read sequentially However, if the report is used as a supplemental text, say in a mining safety course, chapters can be assigned in any order to supplement other readings.

Jan 1, 1988