Search Documents

By S. Banisi, M Nesari, J. A. Finch, N. Nobari, H. Javani

"The flotation circuit of the Sarcheshmeh copper mine, which processes 40,000 t/d of ore at 0.9% Cu, consists of rougher, cleaning and recleaning stages. Mechanical flotation cells are used in all stages. To investigate the amenability of flotation columns in the plant especially for cleaning and recleaning stages, a column was designed, constructed, and installed at the Sarcheshmeh pilot plant. The pilot plant, which has an identical circuit configuration compared to the plant, can process up to 2 t/h of ore. The overall rate constant of the ore along with the target recovery of 94% were used to size the column. A 26 cm by 550 cm column with two filter cloth spargers and a submerged froth washing system using perforated tubes was constructed. To detect the interface level a 180 cm conductivity probe consisting of 1.5 cm diameter ring electrodes was installed. The tailings flowrate controlled by a variable speed pump was used as the main control variable. The initial testing program revealed that the optimum superficial gas and wash water flowrate were 1.5 and 0.3 cds, respectively. It was observed that the cleaning stage grade when using the column could increase by 2-3% at constant overall copper recovery.IntroductionThe Sarcheshmeh copper ore body which may rank as third or fourth largest in the world contains 1 billion tomes averaging 0.90 % copper and 0.03 % molybdenum. It is in located south-east Iran and has been processing 40,000 t/d of ore since 1982. After three stages of crushing, the ore with a F80 of 12.7 mm is fed to 8 parallel ball mills in closed circuit with cyclones to produce a product 70% finer than 75 microns. The concentrate of the first stage of flotation is reground and the tailings constitutes the main component of the plant final tailings. A concentrate with an average grade of 31% Cu (chalcopyrite and chalcocite) is obtained after cleaning and re-cleaning stages in mechanical cells. Total recovery of the plant varies between 83-87 % depending on ore type and operating conditions."

Jan 1, 2000

By P. -M. Tardif, S. Outalha, R. Le

"This paper proposes a new direction to implement an underground mine communication system. It presents actual underground communication systems and discusses their technological limits. A new system based on a wireless local area network (WLAN), together with its main systems characteristics, is then proposed. This paper also presents an experimental protocol for radio frequency propagation measurements. Finally, the paper describes the projected implementation of a WLAN in an experimental mine. IntroductionDuring the last decade, a number of Canadian mining companies have invested in modern communications systems in order to automate processes and reduce operational costs. Safety of miners is also a concern, regulated by health and safety regimes.Underground communication systems rely mainly on analog technology (especially the leaky feeder). Digital upgrades have been made to modernize this technology using a coaxial or fibre optic cable to transmit voice, documents, commands, controls, and video. Therefore, all wired equipment can benefit from an increase in efficiency from the digital technology.However, when it comes to mobile equipment, the only medium was, and is, still radio waves. With the advent of the wireless local area network (WLAN) standard, one can use a technology similar to that of the cellular phone to connect transparently different equipment. WLAN enables the transmission at rates higher than 2 M bits of voice, documents, commands, controls, identification, and of course, digital video. This technology was developed with inbuilding use in mind. Now, one can try to adapt it to underground mines."

Jan 1, 2000

The operations management system at Olympic Dam has evolved over a two-year period to the state described in this paper. This evolution has been driven largely by the requirements of the recent expansion of the Olympic Dam operation from three to nine million tonnes of ore per year. Such a change process demands an holistic approach to mine management and several techniques have been employed including XPAC, Mine Works Planner as well as a basic philosophy of æjust-in-timeÆ completion. The philosophies, software and tracking mechanisms for managing a large tonnage operation are described, outlining a fully integrated scheduling system from shift to shift detailed activity planning to a 20 year production plan. Moreover, the vision of production exceeding the current limit of nine million tonnes means that there are to be further developments to this state-of-the-art system in use at the Olympic Dam mine.

Jan 1, 2000

By S. Ferlay

"The main purpose of the ZIMA VAL project (Label EUREKA EU1367 and LIFE ENV/F/000278) is to demonstrate industrial scale recovery and recycling of the main components of used dry batteries (zinc, manganese dioxide, mercury, and stainless steel) into high added value products. The originality of the ZIMA VAL process resides in:1- the use of hydrometallurgy2- alkaline treatment implementation (highly selective) for zinc and mercury3- electrochemical recovery of high quality products.4- the recycling of all the battery components (zinc, mercury, manganese dioxide, stainless steel) ·5- low operating and investment costs.The process consists of physical classification, mechanical dismantling, hydrometallurgy and electrochemistry. The purpose of the demonstration plant in FALAISE (Calvados - France) is to define the technical and technological parameters of an industrial unit for the treatment of 2400 tonnes per year of used batteries."

Jan 1, 2000

By Timms. Greg P., John W. Bennett

A field-based method for measuring the diffusive oxygen flux through covers placed on sulfidic waste rock dumps has been developed and applied at a number of mine sites. The technique provides a means of quantifying oxidation rates in dumps and can thus be used to assess the effectiveness of cover systems. Two instruments can be used. The first is portable and easy to set up, enabling a picture to be built up of the overall diffusive flux into a dump by making measurements at a sufficient number of locations. The second is installed beneath a cover and is preferred in situations where oxygen is consumed in the cover since it provides a direct measurement of the oxygen flux into the underlying waste rock.

Jan 1, 2000

By D E. Langberg, D R. Swinbourne

The past century has seen the development and commercialisation of many new pyrometallurgical processes based on gas injection. The driving force behind this trend in smelting and refining technology was the increased productivity and resulting increase in capital utilisation achievable. However, measurement of system variables is not easy and their effect on the rate of the reactions involved is not well characterised. One of the critical parameters is the gas-liquid interfacial area produced by gas injection. Related variables such as bubble size and velocity, and gas hold-up fractions in aqueous systems have been measured using combinations of physical (visual, audio and electrical) and chemical techniques. Models have been developed relating interfacial area to physical properties and operating variables and attempts made to extrapolate these to high temperature, liquid metal systems. The only attempts at validation of these models have used either low temperature liquid metals, such as mercury or WoodÆs Metal, or operating plant data. This paper reviews existing knowledge of the effects of system variables on total interfacial area in gas injection systems. Interfacial area is calculated from a range of published experimental aqueous and liquid metal systems and used to assess existing models. An operating region diagram was developed to assess dynamic similarity between experimental and industrial systems. It highlights areas where further research into both measurement techniques and experimental system variables is required in order to extend knowledge and guide further technical and design advances into the 21st century.

Jan 1, 2000

By Thomas W. Camm

This study was done to evaluate the costs of various dumping operations at waste and spoil piles. It has been theorized that accidents associated with dumping operations might be reduced by short-dumping rather than edge-dumping, but many operators have been reluctant to use short-dumping because they believe it is not as cost effective as edge-dumping. To evaluate this perception, researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health reviewed the costs of various dumping methods at waste and spoil piles. The study found that overall cost differences between the two methods were not significant in most cases. However, while overall cost differences between the two methods appear small, capital costs could be more significant when short-dumping if numerous dump sites are used concurrently. The choice of which method to use should be based on considerations of the safety of dozer and truck operators.

Jan 1, 2000

By M Scoble, E Rubio

The re-engineering of manufacturing production systems has demonstrated the benefits from using production information for optimising processes. This paper explores the techniques and issues in the acquisition and analysis of mine production data for tactical decision making in production control. The use of information and operations management tools is presented in the context of block caving studies, with particular focus on the relationship between secondary breaking and LHD production performance.

Jan 1, 2000

By Hiroshi Ono

"By newly developed ICP method, trace amounts of As(III), As(V) .,Sb(III) and Sb(V) were precisely determined within accuracy of sub ng/ml. As(III) and Sb(III) were separated from As(V) and Sb(V) by extracting into ·xylene as diethyldithiocarbamate complexes using diethylammonium diethyldithiocarbamate (DDDC), and then back-extracted into nitric acid for a quantitative determiruition by ICP-AES equipped with hydridegeneration system The recoveries of As(III) and Sb(III) were satisfactory throughout the extraction with 0.04mol/l DDDC in xylene from lmol/l hydrochloric acid solution and the back-extraction with 7 mol/l nitric acid. As(V) and Sb(V) were reduced to As(III) and Sb(III) by ascorbic acid and potassium iodide, and their quantities were determined as mentioned above. The detection limits were found to be 0.58ng/ml for As(III), 0.63ng/ml for Sb(III) using 50ml of a sample. The proposed method was applied to analysis of the real sample.Introduction In drain, arsenic(AS) concentration is prescribed below 0.lmg/l, so As must be removed. As is existed at .the form of As(III) or As(V) in solution. For t1Jeir difference of chemic;µ property, it is not easy to remove As in solution. So it is an urgent necessity to develop for determining concentration of As(III) and As(V). Antimony( Sb) has resemblance .chemical property to As. So Sb was experimented the same as As.The separation and determination of As(III) and As(V) have been carried out using several methods, such as ICP after copreclpitating separation, HPLC, direct hydride generation atomic absorption. However these methods have some problems. One of main problems is that HPLC and direct hydride generation atomic absorption methods are influenced by coexisting elements."

Jan 1, 2000

By Mitsuhiro Ohtaki, Tetsuzo Arakawa, Fujio Murata

Refining of Zn from aluminum scrap melt by some vacuum distillation processes was studied to promote aluminum scrap recycling. Effects of distillation conditions, such as melt temperature, vacuum pressure and holding time, on Zn distillation behavior were investigated theoretically and experimentally by 0.3kg/ch scale vacuum resistance furnace. Three methods to increase the surface-area/volume ratio of liquid metal, such as gas atomizing, mechanical atomizing and mechanical stirring, were tested to increase the Zn distillation rate in 5kg/ch scale vacuum resistance-furnace. It was easy to lower the remaining Zn content to less than 0.1 wt% within one minute by mechanical stirring method. A water-model simulation experiment indicated that a significant agitation of the melt by stirring would be effective to increase the distillation rate. Continuous agitation vacuum distillation process (CA VP) has been designed and the pilot plant is now in construction.

Jan 1, 2000

By Fabiola Alvarez, Ana E. Bote, Daniel Pasquevich

"The oxidation of aluminum and its alloys was extensively studied for improving the corrosion resistance in structural materials having high specific strengths. But this reaction involves the formation of a very thin barrier layer on the metallic pieces. Furthermore, the ·recent development of the directed melt oxidation process for producing metal-ceramic; composites has renewed the interest in the study of interaction between gases and metals. Oxidation experiments in the presence of different chlorine partial pressures and at different temperatures were performed in ·a thermogravimetric balance, and microstructures were analyzed by electronic microscopy and X-ray diffraction. The oxy-chlorination kinetics was determined and the oxide formed W(IS amorphous at temperatures below 600 °C and crystalline .at higher temperatures. The appropriate experimental conditions for the fastest completed oxidation was further determined.IntroductionThe use of fine powders for the manufacture of ceramic components has significant advantages. They include excellent sinterability; low sintering temperature and better microstructure leading to improved mechanical properties. The conventional method of producing fine oxide powders involves controlled precipitation and pirolysis of suitable salts. The main limitation of the high temperature decomposition route is the evolution of environmentally unacceptable and corrosive gases. Controlled precipitation of hydroxides from solutions of salts, followed by thermal treatment involves large volumes of solutions and the calcination step that can induce grain growth (1).Direct oxidation of aluminum metal for producing alumina powder requires high temperatures for the direct oxidation of molten Al alloys by a vapor phase oxidant process (2, 3) or high technological process like thermal plasma reactor ( 4).Oxidation of high purity aluminum (5, 6) below the melting temperature· is initially characterized by a nearly linear reaction rate, followed by a rate which decreases rapidly with further weight gain. However, the oxidation rate of an aluminummagnesium alloy is much faster and it does not conform to any common oxidation law, but it is nearly parabolic at temperatures between 200 and 400 °C, an nearly linear· above 400 °C."

Jan 1, 2000

Atlas Copco Wagner launched its ST1010 Scooptram load haul dumper. The ST1010 replaces the company’s Wagner ST-1000 Scooptram. The improvements to the Wagner ST1010 include increased reliability, ease of maintenance and driver comfort or ergonomics. The ST1010 has been redesigned and has added several new features and options not offered in the earlier model. These include anew boom design with side stops. Heavy reinforcements to the bogie offer better protection against the harsh working conditions in underground mining and tunneling. An auto lube system has also been added as has paint-on grip tread to reduce slips and falls during maintenance checks or repair work. Other features include a heavy-duty, auxiliary-fan motor, an isolated transverter, remote diagnostic pressure taps, a bolt-on battery box, raised air-intake, improved fuel-filter access for easier maintenance, larger wear-bars around the engine tub, and smaller, higher output batteries

Jan 1, 2000

By Mingchun Lu, Yunjin Yan

"This paper describes a new type of bell-less top installed on two relined blast furnaces at Tianjin Iron Works and another new-built at Echeng Steel Works in China. A compact installation was presented for existing furnace top innovation with the least reformation of existing top structure. A water cooling and sealing gearbox used for driving the chute discards completely the traditional idea about necessity of continuous supply of cooling gas for the gearbox. A multiring spreader and its dozens of selectable charging patterns enables an operator to achieve optimal burden distribution easily under the condition of a minimum investment of control equipment. Some useful conclusions have been made through a small-size model and a full-scale model tests. The excellent characteristics and the superiority of the new top have been fully proved at both works.IntroductionIt is known that there are some advantages with the bell-less top of a blast furnace: suitable for furnace to operate at high top pressure, capable of realizing optimal burden distribution, less investment and maintenance costs, etc. But why do most of blast furnaces in the world still remain using conventional bell top. One of the concerns is that current bell-less tops still have some shortcomings:1) The height of a current bell-less top might be lower than three or four-bell top or two-bell plus valve seal top, but still much higher than an ordinary two-bell top.2) The gearbox for driving the rotating chute is positioned onto the lip of the furnace. It is subject to attack by crude hot bf gas. Continuously pumping cooling gas (pressurized nitrogen or clean bf gas) into the gearbox is indispensable to withstand such a harsh working environment. Therefore, a plant furnished with blower8 and its ancillaries has to be built, It involves a large sum of investment and much expense in its annual running costs.3) Although the current bell-less charging device as a means of controlling burden distribution possesses a wide range of freedom, it is difficult to realize optimal burden distribution. There are some large blast furnaces realized better burden distribution, but sophisticated control means is indispensable so that the investment of control means is much higher."

Jan 1, 2000

By M Eichorn

Running a successful reagent plant trial is not an easy task, especially when trying to achieve an incremental improvement in a highly variable process, such as flotation. Cytec aims to achieve one per cent recovery improvement with 90 per cent statistical confidence. Most concentrators experience large fluctuations in recovery and so the æmagicalÆ one per cent is difficult to detect. With the aid of statistical software, including REFDISTR (proprietary) and ECHIPR, Cytec have developed a unique approach to differentiate between daily operational variation and actual process improvement. This paper describes how Cytec runs a plant trial based on extensive laboratory investigation and detailed analysis of historical plant data using statistical techniques.

Jan 1, 2000

By Hugo T. Dummett

I would like to share some observations about the mining business and place the ongoing discussion in the context of our changed world. The mining industry practices its trade in a universe defined by prices, laws and governments. Prices, as in what the industry is paid for what it produces, and the costs of goods and services. Laws that have to be transparent and fair. And governments that the industry prefers to be stable and supportive of the industry, and certainly not corrupt. However, the day-to-day realities of the mining business in 2000 are not what they were 10 years ago. Several events have occurred that have resulted in a less populated workplace that is obliged to work much smarter and faster. These include real declining prices for most mineral commodities; low and diminishing returns to company shareholders; massive restructuring of the industry through mergers, partnerships and alliances; gold’s changed role from reserve currency to just another commodity; the growing importance of native title and the startling imperatives of “sustainable development.” In addition, the “borderless world” now means that resource companies will need to pass the test of being responsible corporate guests who respect and enhance the social, moral and societal values of their host countries.

Jan 1, 2000

By J. M. Rapkoch

In late October 1996, an acid plant at a major U.S. copper smelter was faced with unexpected and rapidly increasing pressure drop across the gas cooling tower in the acid plant, indicating a build-up on the packing. This threatened to halt operations if not resolved. Earlier that month, a smaller vessel in the acid plant was found to be completely plugged with lead sulfate. It was feared that a similar fate awaited the gas cooling tower unless the scale build-up was stopped. Although lead sulfate is present in most copper smelter acid plants, this accumulation was unusually severe. An investigation was launched to find the source of the lead, determine how lead is transported to the gas cooling tower, recommend operating practices to prevent such severe scaling, and seek ways to recycle the lead value in the scale covered polypropylene packing. Late in the investigation it was learned that the lead originated from an improperly executed recycling program.

Jan 1, 2000

By K. Viking

The vibratory characteristics of full-scale sheet piles, vibratory driven into the ground, have so far not been described systematically in detail. This paper concerns the preliminary results of a series of full-scale field tests where both the driveability and induced ground vibrations have been continuously monitored. Furthermore, the results of measured ground vibration levels have been measured at two different sites characterised as having hard and easy driving conditions. In the light of the presented results, the paper briefly discusses how the complexity of a driveability and vibration prediction can be subdivided into three parts, namely, vibrator-, sheet pile-, and soil-related parameters, all of which significantly affect both the driveability and induced ground vibrations.

Jan 1, 2000

By Kallioinen Jouko

"Advanced Flotation Technology is the application driven design of Don-Oliver flotation cells to achieve the optimum performance for each type and grind of flotation. Optimum performance is the combination of both recovery and selectivity.Optimized performance is the combined product of optimized mixing and effective froth removal. Optimized mixing is applied to roughers, scavengers, cleaners and specialty cells such as those to float hydrocyclone underflows in both primary and regrind circuits in order to reduce overgrinding. Effective mixing for fine material is easy, but overmixing reduces selectivity in frothbed.Selectivity in flotation is an important target, especially when treating complex ores, and parameters in frothbed have been examined to improve the separation of minerals and eliminate circumstances that reduce separation rate.Advances in process control have been achieved with expert controls and instructive operator information data. This has gained a higher degree of understanding of cell operation and ore type being processed to be used in future process development work. Excellent results of this Advanced Flotation Technology have been achieved and designs through 7000 cu ft (200 m3) are currently available for high capacity concentrators. This paper will detail how flotation cells are more responsive to the exact requirements of the duty specified."

Jan 1, 2000

The objectives of mining grade control are presented and examples of the techniques used in various open pit and underground mines are used to define the attributes of good grade control. Reasons are discussed for the success of various improved practices. The progressive development of grade control is presented and the balance between quantitative and qualitative data is analysed. The skills and resources required for grade control on mine sites that are using best practice are also presented. A number of problems in grade control have been solved recently however there are still issues that need to be addressed. Examination of the grade control process frequently stops after sample quality has been examined. There is much more beyond this that can now be optimised using conditional simulation models. Other future directions of mining grade control are also suggested. An extensive bibliography of published papers on grade control is included that will be maintained and updated on a website.

Jan 1, 2000

By L. M. Scovell

The Internet and its related technologies will radically change the way that mines manage and control their maintenance, repair, and operating supply chains. The Internet is creating new distribution channels and offers new technology platforms with significant advantages over more traditional methods. Mines will have to re-evaluate both the strategies and the tactics employed in these areas. Mines will use e-commerce to integrate their maintenance, repair, and operating supply chains. The integration will extend beyond traditional trading partners to a worldwide network of communities with similar interests and goals. The changes will transform the way mines operate, lower mining costs, and thereby increase their chances of success in an increasingly competitive environment.

Jan 1, 2000