Search Documents

By R. MacRosty, R. Pula, P. Gebski, W. Braun

"This paper provides a progress update on three tapblock monitoring technologies that Hatch has been developing with our clients for non-ferrous smelting furnaces.The Tapblock Diagnostic System (TDS) is an advanced on-line monitoring system that uses temperature data along with embedded thermal model results to evaluate the condition of a tapblock over its campaign life. Hatch recently installed a second Tapblock Diagnostic System, some details of which are provided in this paper.The Tap-hole Acoustic Monitoring (TAM) system is installed on water-cooled copper tapblocks and uses the noise from the tapping channel to provide a qualitative indication of wear and deterioration of the tapping channel refractory. In addition, TAM can be used to monitor drilling and lancing performance, and potentially could also be used in the future as a guide for automatic drilling and lancing systems (Sadri et al., 2008).The third technology is the use of fibre optic sensors to measure temperature on the hot face and in the tapping channel of a tapblock. Fibre optic technology allows installation of numerous sensors in key locations where they are very sensitive to tapblock condition and also provide more extensive spatial coverage than is possible with traditional instruments. This paper provides an update on our efforts to address issues with premature failure of the sensor cables due to corrosion, and also converting the vast amount of data from the sensor cable into information that can be used by furnace operators."

Jan 1, 2014

By Y. M. Zhao

Reutilization of waste printed circuit boards (PCB) can not only prevent potential environmental pollution, but also achieve recycling of secondary resources. Study on recycling of discarded PCB belongs to the front edge of environmental pollution prevention and resource recycling. In order to effectively crushing waste PCB, and solve the problem of secondary pollution of fugitive odor and dust during the crushing process, a wet impacting crusher was adopted to achieve comminution liberation of PCB in water medium. 96.79% of the crushed yield was distributed in ?2mm, and metal took 97.18% in this grade of production. Size distribution of PCB particles was characterized double peaks at the sizes of ?1+0.5mm and ?0.074mm. A double Rosin-Rammler function, is called DRR function, is put forward to describe the size distribution of PCB particles. The DRR function of cumulative weight percentage oversize of PCB was non-liner fitted by self-defining DRR function of the Origin 7.0. The evaluation indexes of the fitting results are the correlation coefficients R2 of 0.9994 and residual E of 0.18671, those show that DRR function is perfectly accurate. Based on the research the mechanical separation and material properties of PCB, a wet process of reclaiming metals from PCB using a new style separator ? tapered diameter separation bed (TDSB) in water medium was designed, and the related separation mechanism was studied. The fluid field of the tapered diameter separation equipment was simulated by the Ansys Flotran software, the variation laws of the velocity in each position in the fluid field as well as the equation of axial distribution sectional max velocity were analysed according to the simulation result, the stress change and motion trajectory of the pellet in the certain fluid field were analysed. The results show that the expanding tubular structure of the varied diameter separation bed indicates gradually decreasing velocity of water flow along the axis, assuming a certain angle in the bed, as a result of the gravity?s influence, and there was corresponding change to the distribution of the flow velocity, thus the whole formed a special fluid field where velocity variations exist in different positions. When the material passed through the fluid field along with the water flow, as a result of the difference to the particle density, the granularity and the shape, there would appear the difference to the motion trajectory as well as the movement distance under the action of the fluid: The lower density materials discharge along with water flow, but the higher density materials would be kept in bottom of the bed and discharge through material mouth. Therefore, light and heavy products were separated effectively according to the density. Using tapered diameter separation bed to process the ?1mm size crushed material of waste printed circuit boards, with the discharge of water 5.5m3/h, feed-rate of the material 250g/min and with an obliquity 35°, product with 93.92% in integration efficiency and 93.73% in recovery ratio of the metal were obtained by the primary separation. Compared with other mechanical methods, the range of particle size was broaden using the TDSB to recovery metals from PCB, and lower limit size of separation almost approach to 0. An innovative process of ?wet impact crushing+ classifying+ tapered diameter separation? recycling metals from waste PCB was developed.

Jan 1, 2014

By Johnny Zhang, Yang Anguo, Li Weifeng, Xueyi Guo

"SKSTM oxygen bottom blowing smelting technology was developed by SKS-ENFI at SKS Smelter, Hunan in the 1990s to replace the conventional sintering process and thus to meet the high national EHS standard for lead.Since then, two major milestones have been achieved:1. Since 2002, the SKS oxygen bottom blowing smelting-blast furnace reduction has been in operation at SKS, YGL, Chizhou smelter etc. Now in China, about 50% of the lead (4.2 millions t/year) is produced using SKS process; and2. Since 2008, the blast furnace has been replaced by direct reduction of molten rich lead slag at YGJ smelter, which is more energy-efficient since no slag cooling is required. This two stage process (SKS Oxidation- Direct Reduction) is named as the YGL process.Since 2008, numerous technological innovations have been implemented in the furnace design, process control, and maintenance at YGL. The plant has been successfully demonstrated its unique excellent performances on all aspects from processing capacity, product quality, energy reduction, cost reduction and emission reduction. The purpose of this report is to update all the improvements with proven tracks.Meanwhile, a preliminary comparison on the following aspects between the YGL process and other similar technologies has been discussed:1. Plant design and operating conditions;2. Mass and heat balances, metal (Pb, Ag) recovery;3. Consumables, oxygen gun and refractory lining life;4. Energy consumption and operating costs;5. Sulfur capture and emission reduction etc.It is concluded that the modified SKSTM process is a clean SO2-free emission process. The process is characteristic of other features such as no extra fuel addition, low capital with a small foot-print design, low OPEX, high throughput, easy operation, long refractory lining life and high productivity (95%+ on line time annually). It offers an alternative cost-effective technology for lead smelting industry."

Jan 1, 2014

By F. Karakas

In this investigation, one of the most energy consuming stage of the cement manufacturing process, grinding stage, was studied. The aim of the study is to reduce the energy consumption. Optimum operating parameters were determined. Experimental studies were performed at three differ-ent stages. Grinding of limestone, clay and marl which are the main components of the cement, to approximately below 90 microns, was the first stage of the cement grinding. At this stage, effect of feed size and ball charge were investigated. At the second stage, the Bond work index of clinker and additives (slag, trass, limestone and gypsum) was found separately. After forming composite cement with clinker and additives, the Bond work index of this mixture was also determined, thus the results of separate grinding and grinding of mixture were compared. The Bond work index of mixture was found as 13.59 kWh/t, while the arithmetic mean of the Bond work index values of components was 14.90 kWh/t. Finally, clinker and additives (slag, trass, limestone and gypsum) were ground under the same conditions. At this stage, laboratory type of ball mill was used in order to understand grinding characteristics of the cement components. As a result of the experiments, it was found that energy consumption for the grinding will be lowered if the mills with 38 % ~ 40 % ball charge are used in the cement grinding. Moreover, grinding with mixture of clinker and additives gave better results than separate grinding of these components in terms of energy consumption.

Jan 1, 2014

By B Mohanty

Currently there exist several explosive quantity-distance (Q-D) rules variously exercised by most countries to protect personnel and property against the effects of accidental explosions. These regulations apply to manufacture, transport and storage of explosive products. This paper reviews the technical basis behind these regulations, as they apply to commercial and military explosives. The characteristics of a blast wave and missiles issuing out of an explosion site and their role in determining the level of damage to a target are discussed. The need for further research on the effect of detonation of charges of non-standard geometry, and under confined conditions such as tunnels is discussed. The challenge in estimating the net quantity of explosives involved and calculation of its TNT-equivalency is also highlighted.

Jan 1, 2014

By J. Rivoirard

Historically, linear and lognormal krigings were first created to estimate the in situ mineral resources of blocks. Nonlinear geostatistics and indicator kriging were subsequently developed to evaluate also the portion recovered when applying a cut-off on selective mining units (SMUs) within blocks. In practice these methods are generally based either on the Gaussian model with a transformation generalizing the lognormal case or on the indicators above cut-offs. Very often the indicator approach is simplified by kriging separately each indicator, and when starting from a continuous variable, a practical advantage of the discretization into classes lies in the easy treatment of a zero effect and of the high values. However, a number of so-called isofactorial models have also been developed for a discrete or continuous variable, where the full cokriging of indicators (i.e. disjunctive kriging) simplifies to the separate kriging of factors. Moreover, these models are equipped with a change of support, allowing a consistent estimation of recoverable resources on SMUs. Min-Max Autocorrelation Factors (MAF) analysis of the indicators offers a new approach for indicator modelling. In particular the first factor, the one with the highest spatial continuity, can help in choosing the type of model. For example a monotonic experimental first factor can be used directly as the basis of a discrete diffusion model, unless a continuous diffusion model such as the Gaussian model can be used on the original variable. This approach is illustrated on a uranium deposit mined selectively: estimates of recoverable resources by discrete disjunctive kriging and uniform conditioning in a Gaussian model are compared locally to short-term estimates based on two areas densely drilled.

Jan 1, 2014

By Liu Fan, Shang Yanbo, Wang Zhongming

"Besides valuable metals of Cu, Sn, WO3, Zn, there are S, Ag, CaF2, In and so on in a complex ore deposit in south China (which belongs to Hu Nan Shizhuyuan Non-ferrous Metal Limited Liability). Although it proved reserve amounts to 3.5×107 ton, its crystal character limits its utilization in large-scale. It features complex relationships between valuable minerals, finest crystallized particle size, low-graded valuable metals (Cu 0.30%, Zn 0.5-0.7%, Sn 0.2%, W<0.1%). If only tungsten minerals are considered, it means WO3 grade is too low (the cut-off grade of WO3 is 0.1% in China). Only Cu and Sn minerals are recovered from 2006 and Cu recovery is less than 70%, Sn 15-20%. Other valuable metals of W, Zn, S and CaF2 were lost in the tailings. To make good use of the ore, the technology of fully recovering Cu, Sn, W, Zn, CaF2 and rare metals are in urgent need. After systematic researches, the flow sheet of "bulk flotation of Cu-Zn minerals at first, then Cu-Zn separation, then recovering sulphide by flotation, then recovering iron minerals by magnetic separation, then bulk flotation of Sn-W minerals after desliming" is developed. Furthermore, specific Sn-W collectors of BK411 and BK412 are applied into the processes and better indexes are obtained. The industrial indexes are listed as followings: the content of Cu, Zn, Sn, WO3 of ROM ore is 0.31%, 0.65%, 0.13%, 0.03%; Cu and Zn recovery are 82.23% and 37.79% respectively; 63.76% of Sn and 34.34% of WO3 go into the Sn-W bulk concentrates. Economic benefits are remarkable."

Jan 1, 2014

By C. Y. Wang

Based on Slurry Electrolysis, and combined with the problems of extraction antimony, lead and their separation from complicated antimony-lead concentrate, a series of tests have been done in this paper. Using Slurry Electrolysis to treat complicated antimony-lead concentrate, antimony and lead can be separated in one step. And 2# metal antimony can be achieved in cathode directly at the same time. Lead in concentrate is restrained still in the residue at the form of PbCl2. After converting the residue with ammonium carbonate and removing sulfur with kerosene, the high quality of lead concentrate (Pb is above 45%, S is below 15%) and pure sulfur can be achieved, respectively. The recovery of all in Slurry Electrolysis process is as: Sb 95%, Pb 95%, Ag 80%, S 60%.

Jan 1, 2014

By H. Huang, R. N. Gow

Acidic treatment of enargite (Cu3AsS4) dissolves both arsenic and copper from the mineral and then attempts to separate them in the leach solution. The reactivity of enargite was examined in acidic to neutral solutions, over the pH range 1-7, to determine a potential range for co-dissolution. Enargite mineral samples from Butte, MT and Quirivilca, Peru were used as working electrodes in a cyclic voltammetry corrosion cell setup, which were then cycled multiple times over -1000 to 1000 mV. Surface reactions and transitions were characterized using in-situ Raman spectroscopy, which were then compared to updated EH-pH diagrams for the copper-arsenic-sulfur-water system from a previous study done under alkaline conditions. The region of co-dissolution is limited to > 600 mV vs. SHE and pH < 1 under the proposed diagram.

Jan 1, 2014

A processing scheme is presented to use one single chemical that has multiple functions to re-duce the use of chemicals and achieve more efficient mineral flotation and solids dewatering. Sti mulisensitive polymers which display hydrophilic/hydrophobic transitions in response to changes in temperature or pH have been found to be useful as such multiple function reagents. They can cause the mineral particles to be either hydrophilic or hydrophobic at one stimuli condition and the opposite at the reverse stimuli condition. Therefore, both particle surface wettability and inter-particle interaction forces are reversibly controllable. When the surface is hydrophilic, particle dispersion is achieved by repulsive inter-particle forces whereas when the surface is hydrophobic, particle aggregation is induced by inter-particle hydrophobic attractive forces. In addition, the hydrophobic surface condition allows for the attachment of particles to bubbles. Flotation and solid settling tests have been conducted with a silica suspension treated with the temperature-sensitive polymer poly (N-isopropyl acrylamide) (PNIPAM). The results indicated that PNIPAM can be used to induce a transition between hydrophilic and hydrophobic surface character at temperature lower or higher than its critical solution temperature (CST around 32oC). Thus, both effective silica dispersion or hydrophobic aggregation and flotation without adding any additional collector have been demonstrated. In tailings treatment, rapid silica settling was obtained with hydrophobic aggregation at temperature above the CST and further sediment consolidation (and water release) occurred at temperature below the CST. Contact angle measurements confirmed the hydrophilic/hydrophobic transition induced by PNIPAM.

Jan 1, 2014

By C. L. Xiao

With reference to the test report carried out by Guangzhou Nonferrous Metal Research Institute in 1983, the mineral process flow sheet of Yichun Tantalum-niobium mine is determined based on the characters of ores and successful experiences in light of the problems in the existing flowsheet: The ore is desilted before crushing; the primary slime is separately treated; the staged grinding process used while the fine slime is collectedly treated with tantalum and niobium as the main recoveries and lepidolite and feldspar powder as the secondary. The flowsheet is featured by comprehensive recovery, low investment and low energy cost.

Jan 1, 2014

By Diana Drinkwater, Tim Napier-Munn

"This paper argues that, although specialist mineral engineering expertise is essential for the efficient design and operation of mineral processing plants, the environment in which these skills are supplied to the industry has changed forever, and not for the better. Most of the mineral engineering programmes in western universities have died or are dying. The long-service mine site mentors have gone, operations are run on a staffing shoestring so that there is no longer the time (or inclination) for considered decision-making, and the FIFO model has discouraged continuity of optimisation projects and communication between professionals. At the same time the technical challenges of designing and operating effective process plants are increasing. These trends are not going to be reversed any time soon, if ever. The ability to run efficient mineral processing operations has been materially compromised as a consequence. We propose that well-designed professional development can help to recover this situation, and it can be done easily and cheaply. The workplace is the best environment for such skills development. Professional development training should be integrated with normal duties throughout the early years of a graduate’s service (and probably beyond), and the cost should be regarded as non-discretionary expenditure for the business. If such programmes are properly resourced and managed and extended over longer time periods, there will be a measureable rise in the level of technical understanding and competence within companies and a resulting beneficial impact on resource utilisation and thus shareholder value. The paper outlines some of the approaches that we believe will work, and the benefits that we expect will accrue."

Jan 1, 2014

By G. Unland

The sizing of crushers depends on the expected crushing forces. However, the crushing forces develop differently with every individual rock while it is compressed by the working surfaces of the crusher. For sizing, this compression process has to be characterized by the maximum crushing force. The maximum crushing force depends on the strength, shape and size of the rock, the amount and velocity of the imposed displacement of the working surfaces of the crusher on the rock and the conditions of the contact surfaces. From experience it is known that the strength of the material and, therefore, the crushing forces depend on the size of the specimen. This dependence is the so called size effect. The determination is based on compression tests. The force development is recorded during the compression of the specimen and for every individual test the maximum force is determined. The occurring maximum crushing forces of several rocks with the same diameter comminuted under the same conditions can be assessed by a mean value and a variance. The relationship between the mean values of the cross section related maximum crushing forces FAmax and the corresponding sizes d of the specimens can then be described by mathematical functions. They are derived from different approaches (phenomenological, statistical and statistical-physical methods). The phenomenological methods are subjective and yield functions depending on the assumptions of a person, whereas the statistical and statistical-physical methods are based on an evaluated function and the optimization of the parameters.

Jan 1, 2014

By X. Q. Cui

The surficial collapse pits of the mining areas are continuously spreading in Beiminghe iron mine of Hebei Province as a result of the exploitation, which has done a lot of damage to the circumjacent ecological environment of the mine. It is a new path to handle the mine tailings at the present time that the thickened tailings are used to backfill the collapse pits, in which way the problems of the surficial collapse and the nowhere discharge of the tailings are both solved, and the rational utilization of the mine tailings and the clean production of the mine enterprise are realized. The?200 mesh content of the tailings of Beiminghe iron mine is 76.87%, and?325 mesh content is 63.50%. Semi-industrial dehydration experiments to the tailings have been done using the hydro-cyclone classified thickening process. The results show that when FX125 hydrocyclone is adopted, the concentration of underflow can achieve 73.31%, and the yield ratio is 61.78%; when FX150 hydrocyclone is adopted, the concentration of underflow is 70.57%, and the yield ratio is 54.31%, which indicate that the minor diameter hydrocyclone is propitious to improve the yield ratio of the underflow. The semi-industrial dehydration system of hydrocyclone classified thickening process is com-posed of FX125 hydrocyclone, D3600 high-efficient thickener and D2000 thickening bucket. The capacity to tailings disposal can achieve 3.07t/h and the tailings can be thickened from 28.86% to 62.45%. Compared with the traditional thickening-filtrating process and the total tailings directly filtrating process, the hydrocyclone classified thickening process has the merits of simple flow and high thickening efficiency, so it is easy to be realized in the mine.

Jan 1, 2014

By Honggang Zhong, Wei Du, Qijie Zhai, Junjie Sun, Jingzheng Ye

"Effects of pouring temperature and cooling water flux on solidification structure of ferritic stainless steel are investigated with a thermal simulation setup. The results show that with pouring temperatures 1518° C, 1528° C, 1538° C and 1548° C, both Lmean (the mean length between columnar to equiaxed transition(CET) position and chill surface of the samples) and the mean dimension of equiaxed grains increase. On the other hand, with cooling water flux 400, 800, 1200 and 1600mL/min, Lmean gradually increases, and the mean dimension of equiaxed grains decreases. In addition, low pouring temperature and cooling water flux enlarge the ratio of fine equiaxed grains.IntroductionFerritic stainless steel plays an important role in industry products nowadays. Compared with austenitic stainless steel which contains both chromium and nickel, ferritic stainless steel can obtain good corrosion resistance despite the absence of nickel [ 1]. F erritic stainless steel has been widely applied in automotive exhaust systems [2], electrical equipment, construction and chemical industries and also has broad development prospects. At present, continuous casting technique has developed into an important technology applied in iron and steel making. The solidification structure of continuous casting slab has significant influence on the final properties of stainless steel. The developed columnar grains of ferritic stainless steel would result in negative effects on mechanical property [3]. However, fine and homogeneou& equiaxed grains can improve the comprehensive properties of ferritic stainless steel [4] Therefore, it makes great sense to promote the columnar to equiaxed grain transition (CET). Recently Baosteel has developed a new type of Cr-saved ferritic stainless steel, but the effect of continuous casting conditions on its solidification structure is unknown. It is important to investigate the effects of solidification conditions on solidification structure of this new ferritic stainless steel, which can give guidance for optimizing the production process."

Jan 1, 2014

By Yuanyuan Wang, Hong Li, Xueting Liu, Hao Bai, Kang Zhou

"Phase change materials are widely used in efficient utilization of energy and new energy technology. Especially, more attention has been paid to composite phase material, which is applied on architectural energy-saving and efficient working fluid. In this paper, stearic acid-silicon dioxide composite material was prepared by sol-gel process from tetraethyl orthosilicate (TEOS) and stearic acid (SA). The material was investigated by Field emission scanning electron microscopy (FE-SEM), Fourier transform infrared spectroscopy (FT-IR) and Differential scanning calorimeter (DSC). The FE-SEM results show that 3D-grids of silicon dioxide were formed clearly and SA was encapsulated in the silicon dioxide shell. The FT-IR results show that there were no chemical reactions between silicon dioxide and SA, which is the chemical property of the composite material, is stable. The DSC results show that the composite phase change material has favorable heat capacity. This material is expected to be used to make a cooling working fluid.1. IntroductionEnergy thermal storage becomes increasingly prominent issue in recent years, because thermal storage has been used in many aspects, for example, it can be added into building materials to improve heat conditioning. Another potential application of thermal storage materials is that the intermittent waste heat can be collected and recycled effectively by using the thermal storage facility. Thus, energy thermal storage plays a significant role in conserving available energy and improving its utilization [1]. Energy thermal storage includes sensible heat storage and latent heat storage. The latent heat storage has great heat density with a constant temperature during the phase change process [2-5]. Large quantities of latent heat storage will be absorbed and released when phase change takes place. Based on the former researches, some phase change material (PCM), such as fatty acid and paraffin waxes, has been proved to have high latent heat storage capacity and appropriate thermal properties [5-6]. However, using the PCM in energy storage systems directly is restricted, e.g. some properties of organic PCM, like form-stability and thermal conductivity, are not good enough to use. Meanwhile, almost all the inorganic PCMs are corrosive and most materials may cause sub cooling and segregation [7-9].The other problem is that the leakage when the temperature reaches the phase change point. Therefore, encapsulated composite phase change material (CPCM) emerged in order to solve the problem of leaking out, minimize the sub cooling and prevent phase segregation. [10-13] However, the easy flammability of fatty acid also has hindered the development of PCM. Accordingly, it has been found out that silicon compounds are environmentally friendly promising substitutes for halogen-containing flame retardants. Especially, silsesquioxanes are excellent in the flame retardancy. So CPCM can be encapsulated with SiO2 acting supporting material."

Jan 1, 2014

By Z. C. Zhen

Basing on character of fine ores, and employing all the advantage of dissolved-air flotation, the study within the dissertation put forth the methods of superfine metal mineral flotation with dissolved-air flotation equipment, and constructed a full set of laboratory flotation system. Experiments both in water and in slurry were respectively carried out by means of this flotation equipment. Further study was also fulfilled on mechanism of air-dissolved released devices, and the key components of system including ejector, releaser and saturator were designed. Optimizing devices parameters were chosen by taking ideal performance of the devices into consideration, according to orthogonal experiments and tests on bubbles factors, those performance factors were called air release rate, air release efficiency. The results with some minerals are better than JJF flotation machine with 30 litres bulk. The Dissolved-air Flotation(DAF) machine shows great potentiality in treating super-fine metal mineral concentration. The research indicates the Dissolved-air Flotation(DAF) system has superiority over mechanical flotation machine in fine flotation. Air-dissolved released bubbles appear on the surface of hydrophobic minerals in priority, solving collision probability less in the tradition fine mineral separation, such that the metallurgy technology of fine metallic minerals are improved. The exploratory research is a foundation for industrial pilot, commercial test and equipment maturity in the future.

Jan 1, 2014

New technology for on-line particle size analysis of mineral slurries has opened up new applications for particle size measurement. In some cases the particle size distribution of the final concentrate is an important quality issue. This paper discusses established on-line particle size analysis technologies and presents experiences on the use of a new technique employing laser diffraction in several minerals processing operations. The main innovations in the new instrument are a simple dilution system and multiple scattering correction algorithm, which allows wide solids content variations of diluted sample in the measurement cell. Representative sample for laser measurement is produced by a simple and reliable dilution system. The applications discussed are; Blaine number measurement of Fe concentrate before pelletizing, grinding of variable batches of ore and paste thickener control.

Jan 1, 2014

By J. Y. Tian

In view of the fact that many domestic iron ore-dressing plant applying flotation cells in the re-verse flotation, to improve the technical level of magnetite reverse flotation, we apply such a technological process of one stage rougher and two stages scavenger flotation column respectively. The middling from the two stage scavenger process are returned to magnetic separation for condensing. By contrast, the technological process of one stage rougher and one stage cleaning flotation cells is made up of by multi-magnetic separation and magnetic middling regrinding separations. It has been proved that the flotation column we offer can simplify the technological process structure, obtain advanced technical indexes, run the system smoothly, reduce energy consumption, and be environ-mental friendly.

Jan 1, 2014

By R. B. Sudderth, A. Quiroz G., M. Torres M., C. Salgado Q., J. Fernández O., H. Bravo P., M. Torres B.

SNF FloMin, Inc. has introduced a complete line of extractants for recovery of various metals. Among them are the CuPRO MEX™ Brand of copper extractants that are based on the well- known 2- hydroxy 5-nonylsalicylaldoxime and 2-hydroxy acetophenoneoxime. This paper presents the laboratory and pilot plant trial results for SNF FloMin’s CuPRO MEX™ 3302 reagent, the equivalent to the wellknown ACORGA® M5640 extractant, and the composition of these reagents are described. Some examples of SNF FloMin’s CuPRO-Sim™ Advanced solvent extraction simulator are presented.

Jan 1, 2014