Search Documents

By K. T. Brashear

Since the MINER Act of 2006, the minimum static load of in-situ underground mine seals has been increased from 20-psi to either 50-psi if monitoring is conducted or 120-psi if left unmonitored. These minimum strength requirements in seals must be designed, built, and maintained throughout the lifetime of the seal. Due to this, it has become necessary to assess the effectiveness of non-destructive testing (NDT) technologies to determine seal integrity, which in this case, are explored using sonic waves and tracer gases. Through both small and large scale testing, two NDT methods will be evaluated for their abilities to determine integrity of the seal. A sonic wave technique to observe a change in wave velocity to identify faults within the seal material. As a NDT method, tracer gases may be used as a potential indicator of a connection between both sides of the seal material through a series of faults and cracks within the material itself. This paper reviews the history of underground mine seals and discusses the overall assessment of sonic waves and tracer gases to serve as NDT methods for estimating the integrity of these seals.

Feb 23, 2014

By J. Brune

The disaster at the Upper Big Branch (UBB) mine 2010 has demonstrated the destructive violence of a coal dust explosion by killing 29 miners in the worst mining accident the United States has experienced in almost 40 years. This explosion brought to light that the United States mining industry must strengthen explosion prevention and explosion hazard detection practices. Recent legislation such as the Mine Improvement and New Emergency Response Act of 2006 (MINER Act) pushed the strengthening of explosion and disaster response and miner protection in addition to stricter regulations on the sealing of abandoned areas and on conveyor belt flame resistance. The focus of this new act was on how to respond to a disaster or explosion, yet not much improvement was made with respect to prevention explosion disasters. Researchers at the Colorado School of Mines have recently concluded extensive research into methane and coal dust explosion prevention practices and regulations as it may be applicable to underground mines in the United States. This research aims to forward more studies into the use and adoption of standards and procedures that have been utilized in countries with strong explosion prevention histories.

Feb 23, 2014

By M. Javier

In business mining, dilution is the result of the operating parameters that occur too often and cause serious consequences to mine performance, questioning TO WHOM BENEFITS DILUTION. Mining persists in changing perception of real meaning of dilution. The lack of interrelation between mineral processes and nature compromises the understanding of dilution; this absence of interrelation occurs due to the misinterpretation of nature, otherwise, Geomimic could be helpful to filling the gap of misinformation. NATURE provides LIMITED metals in low content deposits; it is a challenge to obtain them. Nature never considers dilution. Furthermore, though dilution is a human concept, dilution is accepted and promoted. Reality of dilution is in its errors accumulation that translates into technology level or status applied in nature. It is doubtful that dilution can continue surviving if it is ?meaningless?. It will discourse: Is dilution illegal? If the change occurs in the prediction of mining will prevail a different destiny, it is important to touch the cores of the business; otherwise, it would represent repetition of the same ?negative? effects, as usual. Mining defines many losses during the disturbance of nature, from NPV elaboration to the metal recovery to commerce, demanding BETTER DESIGN. This paper introduces and applies MANAGEMENT BY LOSS, as first steps, to limit risks and uncertainties in mining. As result, the management of dilution will be obtainable under mining practices which promotes its character of SUSTAINABILITY.

Feb 23, 2014

By W. G. Pariseau

A study of coal pillar strength was done at the Beehive Mine during a three year period, 1974?1977, in a cooperative effort involving the University of Utah, RE/SPEC, Inc., and the American Coal Company (Pariseau et al, 1977). The Beehive Mine is located in the Wasatch Plateau coal field in central Utah near Orangeville, Utah, where mines are developed from outcrops between steep canyon walls with topographic relief of a kilometer or so (3,600 ft). Coal is found in Cretaceous sediments that dip gently to the west. Detailed geology of the Wasatch Plateau is described by Doelling (1972). Mining was done in the Blind Canyon seam. An earlier Deseret Mine worked the Hiawatha seam that is lower in the stratigraphic column by about 36 m (120 ft). Mining progress and ownership changes occurred in time with mine mergers and name changes eventually to the collective Des-Bee-Dove label. At the Beehive Mine, depth varied with topography but was approximately 360 m (1200 ft) on average; seam thickness varied from 1.5 to 6 m (5 to 20 ft) and usually required two passes of the miner. The mine was eventually closed and finally reclaimed in 2003. Semborski and Oakley (2006) present a brief history of the mine and describe the reclamation work in some detail. Figure 1 shows the surface topography in the vicinity of the mine that is in the center of the figure.

Feb 23, 2014

By M. Baumann

Operating and maintaining the heavy equipment used in open-pit mining operations is an ongoing challenge for mines. Typical operations employ a combination of shovels, wheel loaders, and haul trucks to excavate and transport the material for further processing. As this is the first point of contact for the material after blasting, it is often a bottleneck of all downstream processes, thus, equipment uptime and efficiency is crucial. Automated systems for bucket tooth monitoring, payload measurement, proximity detection, and rock fragmentation analysis will be examined. The impact of these systems on operation safety, efficiency, and reliability, in real-world scenarios will be investigated. The process of managing all the above fleet of equipment in a mine can be streamlined by connecting the equipment monitoring systems to a central server. Using the central server, the distribution of this information can be automated to ensure that the right people see the data in a timely manner, improving both proactive and reactive responses to threats to safety and productivity.

Feb 23, 2014

By J. Tavares

It is no mystery why the mining industry has such lofty safety standards. In dealing with Mother Nature and gravity, the combination of the two can create significant hazards from high wall and tunnel collapses to huge landslides. The loss of production from a major disruption could be enormous. The price tag on the loss of human life is immeasurable. The evolution of geotechnical instruments and software has been ongoing for years. But the biggest innovations have occurred during the era of cell modems, internet, and wireless networks, allowing for real time data and alarms to be delivered globally anywhere and anytime to one?s computer, laptop and smartphone. Yet in some ways you can thank the urban construction projects for developing much of the technology in use by today?s mines. Due to the density of population and the billions in dollars of structures and infrastructure in cities throughout the US and the world, urban projects have faced intense scrutiny for years. Out of this scrutiny was born the necessity of real time automated monitoring of instrumentation and sensors, a defence against catastrophic failures, and real time early warning systems through alarms that can and do saves lives. It is also possible to identify areas of concern with subsequent remediation prior to failure.

Feb 23, 2014

By D. Spitty

Mining companies often have many disparate systems and repositories of data in their organization for planning and scheduling outbound mining supply chains. To optimize ore quality, throughput, transport logistics scheduling and delivery to contract, planning teams need to model and manage the value chain accurately and achieve a consolidated, enterprise view of operational performance. Planning teams coordinate a complex series of activities to ensure production forecast accuracy. They also negotiate and execute complex contracts often with disconnected and limited visibility of production forecasts, quality, and variability with little ability to accurately market potential product specifications over longer time horizons. This market is becoming increasingly dynamic, with increasing variability and the time for planning teams to react is decreasing. This is driving the need towards using science to generate the necessary scenarios required to support the decisions made by planners on a frequent basis. Resource-to-Market is a highly flexible, user-configurable supply chain management system for the mining and metal processing industries. This provides an integrated view of the supply chain that supports the dynamic nature of planning in a mining company, embraces variability of elements across the supply chain with the ability to optimize across all the functional areas of the operation to enable optimal decision making for often competing objectives such as throughput, quality, cost, revenue and profit.

Feb 23, 2014

If the communication/tracking system of an underground mine is severely damaged in a large mine accident or explosion, a surface based seismic system could be the only available tool for locating any trapped miners. This paper documents a field test of a seismic system at a room-and-pillar coal mine in Eastern Kentucky. Testing was performed at 6 different depths (450, 575, 750, 1175, 1525 and 1700 ft) above the mine. For each location underground, the miners pounded a ?set? of 5 ?repetitions? on the roof with each repetition being about one second apart. Over the 3 day field test, 63 sets of underground miners? pounding were detected by the seismic system at depths up to 1175 ft and at horizontal offsets up to 890 ft. Also during the testing, the observed signal strength generated by pounding with a crib blocks was seen to average 180% stronger than the observed signal strength generated by pounding with a sledgehammer. Ultimately, this field test was very successful and definitively demonstrated the ability of the seismic system to detect potential trapped miners? pounding up to a depth of 1175 ft.

Feb 23, 2014

By S. D. Abbott

Mines are filled with a mixture of gases, some of which are toxic, flammable, or explosive. Others serve as early reporters of impending problems. Mines monitor these gases in order to ensure the safe, efficient operation of the facility and avoid losses or disasters. Two different approaches to monitor these gases have historically been taken. One kind of device measures the amount of each gas present by using selective detectors (e.g. handhelds and spectrometers). Another kind separates the mixture of gases into the individual constituents, then measures the amount of each gas present (e.g. gas chromatographs). Handheld units are the most widely used, but gas chromatographs are the most powerful yet underutilized units available to enhance mining operations. There are many misconceptions about the nature, applicability and proper use of each type of device, and little data is available. Up to this point, many people had only the manufacturers? claims to guide them. This study was undertaken to clarify the range of applicability, important characteristics, and value in use of these units in real-world situations. An additional goal of the study was to provide ways to evaluate comparative data, and thus aid mining operations in choosing the most beneficial and reasonable ways to use such devices in various situations and contexts.

Feb 23, 2014

By A. Habibi

The FMC Westvaco Trona Mine is located near Green River, Wyoming and has an annual production of 4.5M tons. Trona is an evaporite mineral that is processed into several products, mostly soda ash. The underground mine has two active development panels and one longwall (LW) panel. The mining horizon is about 500m below surface and the surrounding strata liberates methane. Three surface-based, blowing fans provide ventilation air as a positive pressure system. The mine operates a 225m long LW face, built by Joy Mining Machinery. Headgate and Tailgate developments are driven with four entries. The recovery room, at the end of each panel, is 8m wide with three access chutes. Additional recovery room support comes for concrete blocks used with a center to center spacing of 1.5m. As the LW enters this pre-driven recovery room there are notable responses and shifting ground stresses. This study was undertaken to measure the ground response using seven vibrating wire displacement transducers. These devices were used to monitor the convergence as the LW approached the recovery room. The methane concentration in the air ventilating the recovery room was also monitored. The correlation between convergence and gas liberation was then studied. The results show that the convergence varies from 0.1m to 0.25m along the length of the recovery room. Ventilating the recovery room becomes critical as methane is liberated from oil shale as the more plastic floor material is disrupted. Appropriate methods are employed to ventilate the recovery room.

Feb 23, 2014

By R. N. Gow

Acidic treatment of enargite (Cu3AsS4) dissolves both arsenic and copper from the mineral and then attempts to separate them in the leach solution. The reactivity of enargite was examined in acidic solutions, over the pH range 1-7, to determine a potential range for co-dissolution.. Enargite mineral samples from Butte, MT and Quirivilca, Peru were used as working electrodes in a cyclic voltammetry corrosion cell setup, which were then cycled multiple times over -1000 to 1000 mV. Surface reactions and transitions were characterized using in-situ Raman spectroscopy, which were then compared to updated predominance diagrams for the copper-arsenic-sulfur system from a previous study done under alkaline conditions. The region of co-dissolution is limited to > 600 mV vs. SHE and pH < 1 under the proposed diagram.

Feb 23, 2014

By J. V. Belke

There are many aspects of a grinding mill supply and installation that can result in the mill not operating as intended, resulting in unplanned shutdowns, poor reliability and headaches for all concerned. One of the largest aspects, both in criticality and physical mass, is the mill foundation; if not properly specified, designed and constructed the mill operation will be compromised. The mill foundation starts with the design specification and loading diagram supplied by the mill builder. The importance of understanding these documents and how to apply them is critical for the start of any mill project. When designing mills with a GMD the foundation must be properly modeled to ensure that all interactions of the mill and motor structures, foundation and subsurface strata behave in the intended fashion. All of the previous efforts can be laid to waste if the construction of the mill foundation is poorly handled. Mill foundations are typically the most massive concrete structure at a processing plant and can easily cause nightmares for inexperienced contactors. This paper explores some of the more important facets along the lifecycle of the grinding mill foundation.

Feb 23, 2014

By E. O. Jacobs

A coupled solid and rock fracture mechanics model is used to analyze the blast driven fracture propagation phase, predict propagation rates, and directly measure shockwave and particle velocity. The study incorporates quasi-static pre-stress conditions for different depths below the surface. The scaled experiments include dynamic material properties and quasi-dynamic fracture mechanics which are shown to significantly affect the fracture propagation. The study was performed using three-dimensional cube-type laboratory models fabricated from Polymethylmethacrylate (PMMA). The test cubes are loaded with explosives and resulting fracture networks are studied. The dynamic evaluation of the spatial crack system is monitored using a high speed image camera. An experimental model set-up is designed to indicate the pre-stress effect on deep borehole blasting and is shown that the pre-stress conditions have a decisive influence on fracture profiles and orientation. It is found that shockwaves rapidly exceed the slower dynamic fractures and a majority of cracks occur due to detonation pressure. Experimental testing using different parameters validate that explosive fracturing can predict the outcome of fracture and crack propagation in any rock type with known material properties. This can be accomplished under great stress conditions deep below ground surface. The experimental study results can be applied to a variety of industries such as mining and quarrying, tunneling, oil and gas, and construction.

Feb 23, 2014

By P. Roghanchi

The difficulties associated with performing direct tensile strength test lead to development of indirect test methods, which are simple, less expensive, and less time consuming. Splitting tensile strength test (Brazilian test) is performed by applying two opposite concentrated compression load across the diameter of a disk specimen until the failure occurs along the loaded diameter. Theoretically, the load is applied over a small width as a line load, however, by increasing the load, the contact width between the loading jaw and the specimen increases as the specimen deforms. The main aim of this study is to investigate the stress distribution in (1) regular Brazilian specimen in traditional tests with loading jaws and (2) flattened Brazilian specimen with flat platens. A series of the splitting tensile strength tests and uniaxial compression strength tests are performed on three rock types: rhyolite, basalt, and limestone. Further, Numerical modeling studies are performed to investigate the effect of the contact between jaw and Brazilian specimen on stress distribution in the disc specimen based on the results from the experimentation. Finally, the stress distribution in the traditional Brazilian test specimen and the flattened end Brazilian test specimen were compared.

Feb 23, 2014

By A. Anani

The goal of hot mix asphalt (HMA) design is optimal material blending to meet Superpave specifications. HMA cost minimization has being modeled as linear programing (LP) (Awuah-Offei et al 2011) and mixed integer LP problems (Brown et al, 2012) and solved with commercial software such as LINDO and CPLEX. Often these software, which are designed to solve general optimization problems, have licenses that cost thousands of dollars. The objective of this study is to develop a novel solution algorithm to the HMA optimization problem presented by Brown et al. (2012), which will negate the need for expensive commercial packages and is specific to this problem. This novel algorithm is based on the branch and bound algorithm for solving mixed integer problems. The algorithm is incorporated into a software package with an easy-to-use graphical user interface. The developed algorithm is validated using a real-life HMA problem. Using this solution algorithm will save companies thousands of dollars, otherwise used to purchase software licenses.

Feb 23, 2014

By J. S. Gardner

Fortunately, few mining professionals have dealt with what all mining professionals fear---a mine disaster. Unfortunately, many have dealt with ?accidents? which may or may not claim lives but nevertheless rise to the level of a ?disaster? given the fallout of liability and litigation in today?s society.1 The undersigned authors published an article some ten years ago regarding crisis management2 based upon their collective first-hand experiences in actual disasters to that point in history. Unfortunately, disasters have occurred since that time, prompting legislation, and a fresh analysis and expansion of those basic principles is certainly in order. Without question, no two disasters are ever alike, yet general guidelines for forming an effective plan of action can be formulated?and if a mining operation is to have any chance of survival after a disaster, such a plan is vital. The primary concern as any disaster evolves remains as stated a 2003 SME article3--the protection of human life. From that point, the focus moves to any assistance that may be needed given the magnitude of the situation. Permeating throughout this process is "damage control." The first step in dealing with a disaster, however, begins long before any threat of danger arises?formulation and implementation of an Emergency Response Plan.

Feb 23, 2014

By R. Wisniewski

Every underground coal mine in the United States must deploy and operate a wireless communication and tracking system. This paper addresses the reliability and availability of an installed tracking system and the communications infrastructure that supports it. A particular interest is the requirements for the systems to operate continuously without failure after a mine disaster for 96 hours, and the requirements in the MINER Act for the tracking systems to be ?calculated to be serviceable? and the communications systems ?redundancy?. These requirements imply a certain reliability and availability. This paper describes a quantitative way to assess these systems requirements, using the tools that are available and commonly used by the Reliability, Maintainability, & Availability community.

Feb 23, 2014

By A. Bascetin

It was recently proposed to use the pastefill technology as a surface tailings management method. Surface paste is an economic and safe storage method that respects current environmental regulations. There are many problems related to accidents that occur in conventional tailings damps. In this study, the applicability of the surface paste disposal (SPD) method for a Pb-Zn mine in western Turkey was examined. Density was 3.084 and specific surface area was 0.899 m2/g. The mill tailings have very low plasticity and show characteristics of clays and silts in terms of the Unified Soil Classification System. The particle size distribution of the tailings was 39.2% particles finer than 20 µm. The results of this study showed that the physical and chemical properties of mill tailings make them suitable for SPD.

Feb 23, 2014

By M. Albrecht

In the mining industry and particularly in the processing plants, we use some large and unusual equipment. Understanding what it is and what it does is important to good operations, but how do you teach a new employee. When I started out in this field, the information on the processing equipment was easy to come by. Equipment manufacturers readily supplied it; their salesmen, often engineers themselves, knew how important the availability of this information was. Old engineers used their notebooks to train the new engineers. Over time this has changed. Equipment manufacturers have changed hands or gone out of business, and often the older engineers are gone. As a start in reversing this, this presentation will be an introduction to sizing, selecting, and operation of some of this equipment, in particular gravity separating equipment. Major portions of this have been excerpted from A Mining Engineers Notebook: Mineral processing (2).

Feb 23, 2014

By T. Good

Twin roll sizers are neither compactly designed machines nor are they configured to accommodate underground mobility; in fact, twin roll sizers leave room for improvement in many aspects of the design. The DRC1200 capitalizes on the weaknesses of these machines to make a more productive, easily maintained, and compact twin roll sizer than current market offerings. These strides were made through the inception of the Hard Rock Extraction System (HRXS), which requires a mobile sizer as part of the system. After use of a third party sizer on the HRXS, potential improvements were evident. These improvements include improved structural design to reduce overall footprint and an optimized design to reduce operating cost.

Feb 23, 2014