Search Documents

By D J. Williams

Tailings management is typically constrained by many factors that are taken as given. These include the tailings production rate that must be accommodated, the desire to deliver the tailings cheaply and easily as a slurry using centrifugal pumps, and a tailings footprint limited by the desire to minimise capital costs leading to a rapid tailings rate of rise and a low settled density. Other constraints include wall raises being delayed due to limited capital, inadequate tailings water and rainfall run-off management, and the net present value (NPV) approach to capital expenditure that puts off expenditure at the expense of performance. All of these constraints result in the tailings occupying much more volume than is necessary, being difficult to rehabilitate, and not being capable of supporting a beneficial post-mining land use or function. Ultimately, such constrained tailings storage facilities will assume very large dimensions, but each will typically be developed as a series of smaller storages that are filled rapidly and added to progressively. The optimal stage to efficiently recover process water is in the process plant, but this is limited by the desire to use centrifugal pumps rather than the more costly positive displacement pumps, which also require greater management of tailings deposition. Process water can also be recovered from the tailings storage facility (TSF) decant. Tailings water that is not recovered from the plant or the decant will be lost to entrainment within the tailings, seepage to the foundation or through the wall, or evaporation. However, tailings water is not always suitable for reuse in the plant, particularly when it becomes contaminated by the processing, and it may simply be stored on the TSF. This will exacerbate the seepage of contaminated water to the environment, and will limit the densification of the tailings that would otherwise occur due to desiccation of the tailings on exposure. If a larger tailings footprint were developed early, cycling of tailings deposition in thin lifts between a number of cells could occur, maintaining the dormant cells dry to enhance desiccation and densification, and ultimate rehabilitation. The end result would be a much reduced stored volume of tailings, the potential for upstream raising, and ease of rehabilitation to a high level. The higher initial capital cost would be overtaken by reduced ongoing capital, operating and closure costs.CITATION:Williams, D J, ?2014. An alternative whole-of-life approach to tailings management, in Proceedings Life-of-Mine 2014 , pp 285–298 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By B Hawkins, S Durkin, V Lawrence

The requirement for secondary egress from underground workings has long been regulated in Australia. Escape way systems have evolved from simple airleg rising ladders and timber ladders to steel galvanised ladders and more recently fully enclosed polyethylene ladders.The polyethylene ladder, Safescape Laddertube, was introduced to the underground mining industry in 2010. It is an enclosed cylindrical modular plastic ladder designed for use in underground escape ways and access ways. Since its first installation in May 2010, the Laddertube has been installed in 43 mines across four countries, totalling 8800 m of ladders installed to December 2013.The Cracow Gold mine is one operation using Laddertube, located 500 km north-west of Brisbane, Queensland, Australia. Upon discovering and developing both the Empire and Roses Pride orebodies, a safe and economically viable secondary egress system and surface primary ventilation exhaust shafts were necessary to support development and production activities to these workings. The need arose to merge these two critical requirements together between surface and underground mine workings some 200 m and 400 m respectively for each orebody. Neither egress has intermediate access points within their full service length from top to bottom. Several options were considered, the preferable and most feasible method adopted was Laddertube.The longest egress length requiring Laddertube within the two vertical surface exhaust shafts was 400 m long, within a 3.5 m diameter shaft. Due to the length of the vertical Laddertube system in both egresses, personnel are to be assisted by mechanical means using the Extended Ladder Climb Assist system.The Gossan Hill mine also uses Laddertube for their escape ways. Part of the Golden Grove operation, Gossan Hill is an underground sublevel open stoping mine located in the mid-west of Western Australia.With a considerable mine life remaining and a history of acidic water and stress related deterioration in vertical openings, the mine operators sought an escape way solution that would provide for the long-term needs of Gossan Hill. Laddertube was selected due to its non-corrosive properties and the ability to fill in around the ladder way to provide stability to the raise opening.Laddertube is a recent development in escape way systems, and is effectively being applied in a variety of operations, meeting the specific needs of underground mines.CITATION:Durkin, S, Hawkins, B and Lawrence, V, 2014. The application of Safescape Ladders at the Cracow and Golden Grove operations, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 311–318 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By M P. Sandy, V Louchnikov, V Eremenko, M Orunesu, O Watson

"Surface support is a key component of most ground support systems which are applied as a means of reducing the risk of rockfall occurrence and maintaining serviceability of mine development. Surface support has two primary functions: distributing the applied load throughout the system by providing connection between rock bolts retaining smaller rocks that unravel between rock bolts.Confinement is also provided to the rock mass, which may increase its capacity to resist further degradation or loosening.Surface support has been routinely installed in most underground mines around the world for many years, yet the operators are still not always certain which type is best suited for deformable ground conditions. A number of factors need to be taken into consideration prior to selecting the type of surface support liner, such as its capacity, availability, practicality of installation, manual handling and loading conditions (static or dynamic) to ensure the system’s optimal performance in terms of safety and costs.This paper presents an overview of the surface support types currently used in underground mines in Australia. Shotcrete, weld mesh, high-tensile chainlink mesh, reinforced weld mesh and high energy absorption (HEA) mesh are discussed. A detailed description of each system is provided in terms of capacity, energy absorption, installation cycle and costs. The cost of each system has been normalised to the units of energy absorbed. The information presented in this paper can be used by underground operators as a reference guide when deciding on suitable surface support type for deformable ground conditions.CITATION:Louchnikov, V, Sandy, M P, Watson, O, Orunesu, M and Eremenko, V, 2014. An overview of surface rock support for deformable ground conditions, in Proceedings 12th AusIMM Underground Operators’ Conference 2014, pp 57–66 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 24, 2014

By G Davison, C Rossimel, M Bouazza

Expanding rock bolts anchor within a rock mass more efficiently than non-expanding varieties. This is of great importance in weak ground conditions, where grouted friction bolts perform less efficiently than in good ground conditions. Filling a Split Set with demolition concrete has been shown to double the load-carrying capacity when compared to conventional use of Split Sets. This report details verification of these results by installing and pull-testing 14 Split Sets of varying grout conditions within in a fault zone. These Expanding Split Sets achieved loads double and triple that of ungrouted and normally grouted conventional Split Sets. A literature review and chemical analysis were conducted to understand the expansion process better. It was found that 20 per cent more calcium is included in expanding cement, which is responsible for its growth. Factors most affecting the expansion process were identified. Furthermore, the expansion rate of a bolt outside a borehole was measured and 6 mm of expansion across its diameter was found. The compressive properties of the cement were compared with other types, due to expanding cement becoming uncohesive after the expansion process is complete. When confined within a Split Set, compression testing demonstrated that this grout is just as strong and rigid as normal grout. Finally, the bolts were tested by shear and it was found that the Expanding Split Set (ESS) has a similar shear capacity to grouted Split Sets, which is 70 per cent higher than that of ungrouted Split Sets. These results enabled the mechanism for improved performance in weak ground conditions to be verified. Expanding grout will expand the Split Set into its borehole of varying diameter and lock it into place, creating increased friction and resistance to pull-out. This paper shows that ESSs can be a useful reinforcement technique in weak ground conditions.CITATION:Rossimel, C, Davison, G and Bouazza, M, 2014. An investigation of expanding split sets in weak ground, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 159–170 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By D Kent, R Paine

"Automated mining systems are increasingly being seen as a key requirement for a productive mining operation in the future. The importance of an integrated communication network infrastructure to support such systems is growing.This paper outlines the introduction of automated mining systems in large conventional mines as well as their growing role in block cave mines currently operating or being developed. The paper will then focus on a case study of how the communication infrastructure is fundamental to the operation of such systems and explain why the resultant communication networks require much more than just increased bandwidth (data capacity) to properly support the automation system within the overall mine operation.Mining operations already embarking down this road are discovering that the required network must be based on a true enterprise level architecture to not only enable the mine’s current plans for remote and automated mining, but also provide a scalable and integrated platform for future developments and requirements. The emerging issues for the communication network to truly support automation systems include: increased complexities of operating and maintaining multiple networks integration issues with disparate systems problems with reporting particularly as demands for corporate reporting and compatibility with enterprise systems become the norm ongoing management challenges, which will only increase with the proliferation of new technologies.The paper will explore how certain mining operations are addressing this by adopting a long-term strategy for automation deployment, which includes laying the necessary foundation architecture to meet their current requirements, while supporting their future visions for the fully automated mine.CITATION:Paine, R and Kent, D, 2014. Developing the foundation communication infrastructure to support remote and automated mining initiatives in underground mines, in Proceedings 12th AusIMM Underground Operators’ Conference 2014, pp 151–158 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 24, 2014

By B Cook, M Karakus, J Light, E K. Chanda

The aim of this research is to develop a model through which the appropriate paste recipe parameters, for example solid content and cement content, can be derived given the stope specific requirements such as stope dimensions, required strength and curing time. A large number of samples and uniaxial compressive strength (UCS) tests were conducted at the Angas Zinc Mine (AZM) paste plant and testing facility. Samples were varied in tailings solids content, cement content and sand content. The results of this testing were modelled to determine the UCS relationship to each of the parameters. The output of this modelling was an easy-to-use program that outputs the design mixture given the stope dimensions and required stope backfill-curing time. This allowed flexibility within the mining schedule for curing times of cemented paste backfill stopes. The optimised schedule using the stope specific mix design, when compared to the standard 14-day curing time used previously, resulted in a smoother weekly mine production schedule. For the modelled 12-week period (one quarter) the 14-day curing time would result in an eight-day shutdown of the mill. The cost for each shutdown is in the order of $125 000/d. Due to the unique nature of each mine’s tailings, this exact outcome would not be directly applicable to another paste fill site. However, the process in this report could be followed for another site to achieve a system similar to the output of this project. This would ultimately lead to a more optimised backfill and stoping cycle and a more optimised mine.CITATION:Chanda, E K, Karakus, M, Light, J, Cook, B and Harris, A, 2014. Optimisation of the paste fill cycle at Angas Zinc Mine, Strathalbyn, South Australia, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 259–264 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By J Harris, J Li, M Shi, P A. Kirsch, D Sprott

Australia has an enviable global reputation as a leader in health and safety outcomes in the hazardous industry of mining, in part due to an increased application of risk management regarding operational planning and mining practice. In 2010, the Australian Coal Association Research Program (ACARP) initiated a major project, RISKGATE, to build, capture and deliver a national body of knowledge to assist companies with the management of risk in coal mining. The online system contains information for tyres, collisions, fires, isolation, strata underground, ground control open cut, explosions, explosives underground, explosives open cut, manual tasks, slips/trips/falls, outbursts, coal bumps and bursts, human–machine interface, tailings dams, occupational hygiene and inrush. In 2014, RISKGATE is developing content for fitness for work (fatigue, drugs, alcohol, physical well-being, psychosocial well-being).This paper analyses underground mining fatalities in Australia and the United States since 2002 and introduces RISKGATE with a focus on the knowledge base for management of hazards in underground operations. Through capturing coal industry expert operational knowledge, RISKGATE provides a cumulative corporate memory at a time of high personnel turnover within the mining industry. This coal-based body of knowledge is a platform that can be evaluated and implemented for other mining domains and high-risk industries within the energy supply chain.CITATION:Kirsch, P A, Shi, M, Harris, J, Li, J and Sprott, D, 2014. RISKGATE and underground operations, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 11–18 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By E Hernandez, I Agustian, W Kusumohastuti

PT Freeport Indonesia is completing the first underground gyratory crusher excavation at their Deep Mill Level Zone (DMLZ) mine located in the mountains of Jayawijaya, District of West Papua, Indonesia. DMLZ is an underground block cave mine with an expected output of 80 000?t/d and a scheduled production start in 2015.In order to deliver crushed ore to the mill through the existing conveyor belt, the DMLZ block cave mine will construct two 1000?kW 1.6?×?2.3?m gyratory crushers with their own respective ore flow conveying systems underground. Each crusher is composed of top, middle, and bottom chambers with an ore bin. This system includes a series of high capacity conveyors approximately 5 km in length including transfer stations and support facilities.The development methodology required a combination of lateral development by jumbo drilling machines and vertical development by mechanised raise climbers (MRC) due to the complexity of the chamber design.This paper will discuss the project scope, design and development methodology, ground conditions, innovative survey controls, and the challenges faced due to the remote location.CITATION:Hernandez, E, Kusumohastuti, W and Agustian, I, 2014. Excavating the first underground Gyratory Crusher at the Deep Mill Level Zone mine, PT Freeport Indonesia, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 43–50 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By T A. Carter

In 2010 Agnew Gold Mine (AGM) struggled to produce the required tonnages from its stopes. The longhole rises used to create void in stopes were unreliable and often failed to gain the designed rise height. The number of firings per stope was having an adverse impact on the ground conditions at the stope brows, impeding stope productivity.Through practical experimentation with longhole drill rigs, box hole rigs and development drill rigs as well as trialling new methods in conjunction with reviewing drill hole data, drill hole accuracy was observed to be an issue on-site. Innovative dragging methods such as the reverse drag, combined with a slope instead of a vertical face on the rear of stopes, have improved dragging and a reduction of firings per stope, enabling larger production blasts.The methods trialled and subsequently implemented at AGM have facilitated the mine achieving budgeted targets for six consecutive quarters. This paper documents the use of these methods in a key lode of AGM’s operations to improve drill and blast practices in order to achieve production targets.CITATION:Carter, T A, 2014. Improving production drilling and blasting in the Kim South orebody at Agnew Gold Mine, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 251–258 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By I T. Ross

In the last 50 years there have been tremendous improvements in equipment used in development on underground mines. Compressed air powered jacklegs have been replaced by high powered electro-hydraulic drifters on sophisticated drill jumbos and load haul dump units have taken over from small shovels and rail cars.Despite the increase in power applied in key parts of the development cycle, average advance rates have fallen and costs have increased. The factor that is most often regarded as the main contributor to slowing advance rates is increased support requirements. Whilst there is no denying that the drive to improve safety has resulted in the requirement for more bolting and the installation of a skin support (mesh or shotcrete), this is not the only factor.Within the industry as a whole, many of the basic principles of development appear to have been lost over time. This paper looks at a historical case study and discusses some of the features of old development cycles that are no longer in use. This highlights some of the basics that appear to have been forgotten. These may be indicators to what may provide improvements in the conventional drill and blast development cycle.CITATION:Ross, I T, 2014. Development – back to basics, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 67–74 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By C Beal

Proper understanding and management of production drilling in sublevel cave (SLC) mines is essential for meeting production targets and for avoiding inefficiencies that could lead to costly bottlenecks. In many SLC mine management models drilling is considered a derivative activity of firing and bogging. Its scheduling is considered to be implied in a firing schedule and given an arbitrary target completion, ‘several weeks’ or ‘a month’, ahead of production firing. Like development, drilling activities are most efficient when conducted separately from other production activities. Unlike development, however, it is not apparent during planning and feasibility how far in advance of firing drilling activities ought to be conducted. This paper presents a method of defining a minimum threshold of drilled stocks above which drilling, firing and bogging operations occur most efficiently. As an example, the drilling activities, procedures, and maintenance at Glencore Xstrata’s Ernest Henry Mine are presented, and the larger scale consequences of improvements to these areas are presented to illustrate their importance in the operation of an SLC mine.CITATION:Beal, C, 2014. Understanding the role of production drilling and drilled stocks in efficient operation of a sublevel cave mine, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 235–242 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

In subterranean mining operations, access to communication networks deep underground is critical for transporting data, voice and video, and other supporting applications that are essential for efficient and safe operations. Whether accessing sophisticated ERP or maintenance management systems, engaging in fleet management, video surveillance, or access control, or protecting miners with wireless locator systems, these networks serve as a literal lifeline between workers deep within mines and surface operations. For this, mining networks require more than permanently installed network cabling, it also requires unique deployable systems designed for quick installation, extension and even relocation as the active mine site area moves, or equipment is moved in and out.

Mar 1, 2014

We have lived through a period of strong metal pricing during the past eight to 10 years. Copper has been hovering in the range of $3-$4/lb during much of the past eight years, averaging close to $3.30/lb. Gold increased steadily from less than $300/oz levels in the early 2000s, reaching almost $1,890/oz in the third quarter of 2011, before tempering back down to the $1,200-1,400/oz range in 2013. Iron ore prices started to rise in 2005 before the staggering increases experienced in 2008- 2010, reaching almost $190/metric ton in early 2011. During the past four years, iron ore prices have ranged from $100-180/t, averaging approximately $140/t. In the aftermath of such a run, it is perhaps too easy to forget where we have come from: The copper price averaged just 77 cents/lb during the six-year period from 1998 to 2003, and averaged just over $1/lb from 1989 to 1997. The gold price averaged $350/oz during the 10-year period from 1994 to 2003. Even more dramatically, iron ore traded in the range of $10-$15/t between 1985 and 2004. So, we have seen sustained, three- to four-fold increases in copper and gold prices, and 8 to 10-fold increases in iron ore prices.

Mar 1, 2014

By M. Tanaji

Over the last many decades, a significant amount of research has gone into the domain of slurry transport. However, design engineers still face many challenges with respect to prediction of pressure drop, critical velocity and other design parameters as a function of Solids % and Particle Size Distribution (PSD). The industry requirement is to transfer the slurry at the maximum concentration as possible (above 30% (volume %)) to make slurry transport more economically viable and to reduce water consumption. To facilitate the design and scale-up of slurry transport in pipelines and in process plants, there is a need for a correlation that can predict slurry pressure drops over a wide range of operating conditions and physical properties of different slurries. The objective of this study is to overcome the limited range of applicability and validity of existing correlations and to develop a generalized but more rigorous correlation applicable to a wider range of slurry sys-tems. The existing Wasp et al. (1977) method is based on multi-phase flow modeling approach. This study attempts to modify this approach by considering material-specific values of Durand?s equation co-efficient and by defining flow regimes based on particle Reynolds number. When compared with experimental data, the modified Wasp method proposed in this study predicts the pressure drop for slurry flows more accurately than other available correlations. Also, the pro-posed method requires minimal test/experimental data for a particular slurry system and can be extended over different input conditions. An iterative computer algorithm is developed to calculate the criti-cal settling velocity and pressure drop in a pipe as a function of Solids % and PSD. The solution method can easily be implemented in de-signing slurry pipes, design validation, and studying the different slurry transport scenarios. The modified method can also be extended to accurately predict pressure drops in dynamic pressure flow networks used in commercial process simulators.

Feb 23, 2014

By K. H. McDaniel

People are our most valuable resource. It is as true today as any point in mining history as we face unprecedented personnel shortages aggravated by a workforce that is aging, significant generational gaps and difficulties recruiting younger professionals all amidst increasing global mineral demand. The educational system has a similar, but slightly contrary problem. Many historically strong mining engineering programs have died. Now, fewer mining oriented universities are trying to produce more students in order to meet the demand. Moreover, their situation is aggravated by a similarly aging workforce, a general lack of mid-career PhD?s with the interest and field experience to teach effectively, an extremely slow hiring and funding process, and an inability to be competitive against private industry compensation packages. The traditional instructional model, while not necessarily broken, is most certainly dated, and can penalize programs and students where schools do not have in-house expertise in a given topic. Mining companies, like Rio Tinto, have the opportunity, if not necessarily the obligation, to positively influence how this model works. Educational Partnerships may be the key. This paper will address some observations, and possibilities, associated with Rio Tinto?s efforts in this area.

Feb 23, 2014

By E. Hasanbas

Vibrating screens and crushers are the workhorses of material sizing. Unfortunately their natural frequency is often in the range of typical supporting structures, thereby making installations prone to vibration problems. Much of the available literature regarding the support of vibrating screens is fairly confusing and outdated. This paper presents the results of utilizing accelerometers and finite element software in the analysis and design of supports for vibrating equipment. It contains data from field studies of vibrating screen and crusher installations, design of new and repair of existing supporting structures, and the correlation between field data and finite element time history analyses. Finally, the paper summarizes a method for analyzing and designing structures subjected to vibratory loads and predicting their behavior.

Feb 23, 2014

Lignite is a kind of easy-to-slime and low rank coal. It is hard to be separated by the conventional wet coal beneficiation technologies. Meanwhile, in recent decades, a large amount of fine coal (-6 mm) is generated as the mechanized mining technology has been progressively deployed in coal sector, which causes a great difficult for lignite beneficiation and upgrading due to lack of efficient technology available. In this paper, a vibrated gas-fluidized bed was used to separate the -6 mm fine lignite particles. Separation experiments of -6+3 mm and -3+1 mm lignite were carried out in a laboratory-scale vibrated gas-fluidized bed. The effects of several parameters including the superficial air velocity, vibration intensity, bed height and exterior moisture content on the separation performance were experimentally studied. The results show that the optimal separation performance was achieved when the superficial air velocity is 0.3, the vibration intensity is 1.4, the bed height is 50 mm, the exterior moisture content is below 4% (-6+3 mm) and 2% (-3+1 mm). And the probably error E values of -6+3 mm and -3+1 mm size fraction of lignite are 0.202 and 0.225 respectively. The results indicate that a vibrated gas-fluidized bed can provide an effective solution for -6 mm lignite separation.

Feb 23, 2014

By S. Bahrampour

One of the basic requirements for designing an optimized rock support for an underground opening is having reasonably enough geological information. It is often financially impractical to obtain detailed geological information about the rock surrounding the excavations. The geological and geotechnical information which are obtained during the construction phase are also usually inadequate and need periodic operation stoppage. Penn State University- J.H. Fletcher & Co. joint venture is to improve the existing instrumented roofbolter so that the 3D geological and geotechnical map of the rock mass surrounding the underground working can be generated real-time as the data is being collected. This information will also be used to design appropriate support for different sections of mines. In this paper, recent results in improving the performance of the measurement while drilling system will be discussed. Moreover, updates related to borehole probing methods for estimating the properties of the rock masses will be presented.

Feb 23, 2014

By V. Králová

The TESCAN Integrated Mineral Analyzer (TIMA), an automated mineralogy system, enables fast and quantitative mineral analyses of rocks, ores, concentrates, tailings, leach residues or smelter products. It combines BSE and EDX analysis for identification and measurement of mineral concentrations, particle size distribution, and liberation/locking parameters. In addition, it can provide bright particle searches for PGM, gold-silver ores, and/or REE. With the newly developed Automated Loading System (AutoLoader), the TIMA has become the world?s first automated mineral analyzer which permits robust, continuous and unattended sample loading. With the AutoLoader (robotics) system, the TIMA has emerged as a powerful plant support instrument. It increases the sample throughput, minimizes manual labor and enables 24/7 operations. As such, it can be used in daily, continuous mineralogy for mine geology/ore control, concentrators, leach operations, and smelter support. It will also increase the capabilities of technical service centers for mining companies, commercial laboratories, large drilling programs or pilot test campaigns. In combination with a highly automated sample preparation lab (sizing, potting and polishing), TIMA technology can establish high-throughput and fast-turnaround automated mineralogy lab modules for mine-site production support.

Feb 23, 2014

Due to the ongoing restructuring of the mining industry in central Europe with a continuous decline of the number of large underground mines and collieries, and a simultaneous decline of staff numbers in the remaining mines, the established mine rescue schemes are endangered to collapse. With the end of the mine rehabilitation at Wismut Uranium in 2014, the last remaining major mine rescue teams in Saxony, providing basic mine rescue services for all other mines in the region, will disappear. This will leave a large number of small mines and other underground operations without capable mine rescue support. Since none of these companies is able to set up a complete mines rescue unit on its own, new ways have to be found. Among others, a central mine rescue team for central Germany as well as the assistance by special trained professional fire fighters or mine rescue teams from abroad are discussed. Problems like location of the central rescue team, financing, communication and transport have to be solved. This paper provides an overview over the complexity of the problem as an example for other mining regions worldwide and will discuss national and cross-national strategies.

Feb 23, 2014