Search Documents

By G van Niekerk, M Wortley

Screening is a critical part of many mineral processing circuits and keeping the aperture of the screening media within specification is vital to ensure efficient performance of the processing plant. Typical ways of estimating and/or measuring the wear of the screening media vary from very subjective methods (for instance, using the human eye) to manually checking the width of a few of the more severely worn gaps with a measurement device. Subjective methods can be flawed by human error while manual checking can distort the polyurethane or rubber materials that are used in several types of screening media. All of these errors can cause either premature replacement of panels or, even worse, poor screening of the material.Metso Process Technology and Innovation (PTI) and Metso Screening Media Solutions (SMS) have developed an innovative method that measures screen aperture using advanced image processing techniques. Field trials of the device are presented in this paper, which shows the comparison between the different methods of measuring apertures. Case studies demonstrate how the system, when combined with ScreenTrack, MetsoÆs industry leading maintenance system, and screening media, is providing users with the best possible screening solutions.

Sep 26, 2011

By E. A. Holbrook

The data in this bulletin were obtained during an investigation of screening practice by the University of Illinois engineering experiment station and the United States Bureau of Mines under a cooperative agreement between them and the State of Illinois Geological Survey Division. Earlier work on this subject includes a study of the general practice of coal preparation in Illinois, made in 1914 and published in 1916,1 and an investigation of Illinois coal-washing methods, results of which were published in 1912 in a bulletin 2 that contained complete information on the methods then in use for sizing washed coal. OBJECTS OF THE INVESTIGATION The present investigation was limited to a study of screening as applied in preparing mineral products with the expectation of obtaining more comprehensive information on screening machinery.

Jan 1, 1925

By M. W. Harmer

Laboratory test work, pilot plant testing and plant experience with wet, fine mesh screens is discussed. High frequency, low amplitude, fine mesh, wet screens were installed on the 6th cleaner concentrate stream. These screens produce a 60% oversize recovery split of the molybdenite concentrate that is of leached equivalent quality. The undersize stream is leached with 'hot ferric chloride to remove Pb and Cu contaminates before roasting or shipment to sulfide customers. This plant modification is a good example of using existing technology in an unconventional flow sheet to yield significant cost savings.

Jan 1, 1990

By A. Garnier, K. Tremblay-Bouliane, B. Gaillet, S. Moineau, D. Tremblay

"A heptapeptide library displayed on M13 bacteriophages (phages) was screened to identify peptide sequences able to selectively bind to gold, chalcopyrite, sphalerite, pyrite, and silica ores, and to evaluate phage potential as bioflotation reagents. Many peptide sequences were isolated through biopanning and differed from known sequences. Adsorption isotherms were determined and a receptor/ligand interaction model was identified and used to compare affinity of peptide sequences toward ores. Some phage sequences have slightly lower affinity to sphalerite than other sulphides. Adsorption was higher on sulphides than on silica. Induction time measurements suggested filamentous M13 phages lower hydrophobicity of the ore surface.RÉSUMÉ Une librairie d’heptapeptides présentés sur des bactériophages M13 (phages) a été criblée afin d’identifier les séquences peptidiques affinitaires à des minerais d’or, de chalcopyrite, de sphalérite, de pyrite et de silice et d’évaluer le potentiel de ces phages en tant que de bio-réactifs de flottation. De nombreuses séquences peptidiques ont été isolées par bio-criblage et différenciées d’autres séquences connues. Des isothermes d’adsorption ont été déterminées et un modèle d’interaction récepteur–ligand a été identifié et utilisé pour comparer l’affinité des séquences peptidiques par rapport aux minerais. Certaines séquences de phages possèdent une affinité légèrement inférieure pour la sphalérite comparativement aux autres sulfures. L’adsorption sur les sulfures était plus élevée que sur la silice. Des mesures de temps d’induction suggèrent que les phages filamenteux M13 diminuent l’hydrophobicité de la surface des minerais."

Jan 1, 2016

By Frank Schmidt

Due to changing geology, rib bolting is an ever-changing problem in ground control. With the economic status of the coal market, the need for safely increasing productivity in rib bolting is at an all-time high. The current solutions used in the market often require a long installation time (e.g. if collapsed holes have to be redrilled) or result in poor quality installations that can lead to insufficient ground control. A new bolting product based on the simple screw principle has been developed to bolt ribs faster and with a more repeatable, higher level of installation quality. The paper covers the product invention and development, the fastening principle and its advantages over current systems and first experiences in the market. The first underground trials have shown that the screw anchors can be installed safely and efficiently, often faster than traditional methods. The screw anchor does not suffer from conventional bolting issues such as collapsed holes due to bad ribs. The screw anchors are designed to obtain steel failure and load testing underground shows consistent fastening in all types of conditions.

Jan 1, 2013

By Lewis. Clifford J.

The purpose of this article is to present design information and operating data on a pilot gas scrubber which is believed to be a new approach for removing noxious gases and particulate matter from the off gases of coal burning power plants and smelters. This principle of scrubbing gases, particularly, scrubbing with an aqueous slurry of lime, was conceived by the author early in 1972. The National Lime Association financed the design, fabrication and initial operation of the unit. The unit was fabricated by Hazen Research Inc. of Golden, Colorado. It has been tested on the off gases of two coal burning power plants and one smelter. The current environmental program has stimulated research and development activity directed toward the removal of sulfur oxides, oxides of nitrogen, particulate matter and other undesirable substances from gases discharged into the atmosphere. At present, most of this effort is focused on the removal of sulfur dioxide and particulate matter by aqueous scrubbing of the gases. This presentation deals particularly with the removal of sulfur dioxide using an aqueous slurry of lime as the scrubbing medium. In recent papers, the author has called attention to-the sludge problems resulting from aqueous scrubbing and to some earlier data on the pilot scrubber about to be discussed.1/

Jan 1, 1973

By Joshua Hescock, Zach Agioutantis

"The Surface Deformation Prediction System (SDPS) has been developed as an engineering tool for the prediction of subsidence deformation indices through the implementation of an influence function. SDPS provides a reliable and fast method for the prediction of mining-induced displacements, strains, tilt, and so forth at any elevation between the seam and the horizontal or varying surface topography. One of the key aspects in obtaining reliable ground deformation prediction results is the determination of the edge effect offset. The value assigned to the edge effect corresponds to a virtual offsetting of boundary lines delineating the extracted panel to allow for roof cantilevering over the mined out area. The objective of this paper is to describe the methods implemented in updating the edge effect offset code within SDPS. Using known geometric equations, the newly developed code provides a more robust calculation of the offset boundary line of the extracted panel for simplistic, as well as more complex, mining geometries. Assuming that an extracted panel is represented by a closed polyline, the new edge offset algorithm calculates a polyline offset into the extracted panel by the user-defined edge effect offset distance. Surface deformations are then calculated using this adjusted panel geometry. The MATLAB® program was used for development and testing of the new edge effect offset feature. In completing rigorous testing regimes, the new offset features will be integrated into SDPS, further increasing the speed and reliability of the programs resulting in a retrospective increase in capability and flexibility. INTRODUCTION Underground operations have been known to cause mining-induced subsidence inside and outside of the mine permit area (Karmis, Agioutantis, and Andrews, 2008). Additionally, subsidence can impact surface water bodies, such as rivers, streams, lakes, and wetlands (Karmis and Agioutantis, 2015; Newman et al., 2016), as well as infrastructure, such as roads, railroads, pipelines, and buildings. With an increase in regulatory focus on mining-induced impacts to local structures, the calculation of mining-induced subsidence indices has become necessary in determining potential damage and mitigation efforts. The accurate prediction and evaluation of mining-induced ground deformations is required to obtain underground mining permits due to potential impacts to nearby structures, as well as hydrogeological sources. The prediction of ground deformation indices is often a complex task due to the number of input parameters required, such as mining geometries, overburden lithology, surface topography, the rate of mining (Karmis, Agioutantis, and Andrews, 2008)."

Jan 1, 2017

By J. Gustavson, E. Mallard, F. Pirkle

The Sales Comparison Approach to estimating the value of a mineral property must always be attempted1 . In addition to other parameters, the approach depends heavily on the availability of transaction data. The consideration for the mineral property must be in form of cash, cash equivalent or other consideration. In other words, “What dollar amount did the property sell for?” Mineral properties are generally real estate, albeit frequently buried deeply under the overlying surface real estate, unless the property may be a quarry. In some states, transactions must be recorded in county courthouses, and the sale consideration must be included. In such cases, the appraiser’s job is made easy. In other locations, the sale considerations are withheld in the courthouse data; but occasionally a local transfer tax is collected and recorded. Again, the appraiser’s job is made easy by back calculation with knowledge of the legislated transfer tax percentage. The worst problem occurs when the consideration for a mineral real estate sale is totally withheld. That may occur in so-called nondisclosure states. A recent map2 of ten non-disclosure states in red is shown below. For the full color code, please refer to the footnote

Mar 2, 2022

By Persifor Frazer

INTRODUCTION For various reasons I have not specified the locality where the research indicated in the following pages was undertaken. It will suffice to say that it was on the grounds of a villa once remote from, but now completely surrounded by, its neighboring city, and in close proximity to an industrial establishment of great extent and importance manufacturing many kinds of steel articles and employing upwards of thirty chimney-stacks for power and process work. The problem was to discover the cause or causes of the mortality to trees and plants on the place, and to trace these causes to their origin. Before undertaking this experimental work, the bibliography accompanying this paper was compiled and studied. It appears from an examination of the careful scientific work performed by the ablest French, German, and English chemists during the last 25 years that they are unanimous in assigning the principal-in fact, the overwhelmingly predominant-cause of the destruction of vegetation to sulphur oxides, resulting either from direct- oxidation of sulphur in oil of vitriol works, etc., or from the oxidation of the sulphur from the minerals associated with commercial coal. Schröder and Schertel showed in 1884 that the sulphates deposited upon the leaves are not injurious to the plants; and Freytag proved that free sulphuric acid could not be found

May 1, 1907

By John T. Awald

The efficiency of search for porphyry copper and molybdenum deposits can be greatly increased. A model exploration system is here presented to show how geologic literature data and field surveys can be aided by modern statistical and computer methods. Assuming that major ore deposits occur in clusters, it is possible to evaluate rapidly large areas at modest cost and with minimum investment risk. An example of the success of these methods is given. Clusters of mine density and metal production covering the State of Nevada were plotted and machine contoured. Selection of a 47,300 square-mile area on the Nevada-California border was made. Within this area, detailed analyses were performed, and a 3000 square-mile site was picked for subsequent field examination. To initiate efficiently the field work, 81 stream sediment geochemical samples were collected and analyzed for copper, zinc, and molybdenum. These data established local variance and necessary statistical controls. Following this, a total of 151 geochemical samples were used to survey the 3000 square-mile area. Computer contouring of results directed attention to specific target areas for detailed geologic analysis, property acquisition and drilling. A total of 22 copper-zinc and molybdenum anomalies were identified. Four of these were recommended for further exploration. To date, two have been acquired and drilled and preliminary ore reserve and financial analysis have been made on one. The estimated cost and time for the regional exploration phases leading to these targets were thirty man-weeks and $16,000.

Jan 1, 1973

By Sirish L. Shah

It is now common to have archival history of thousands of sensors sampled every second over long time. Yet we frequently have process engineers complain:??.We are drowning in data but starving for information??. How can these rich data sets be put to use? This paper addresses the issue of information and knowledge extraction from data with emphasis on process and performance monitoring including fault detection and isolation. Most of the major plant, factory, process, equipment and tool disruptions are avoidable, and yet preventable fault detection and diagnosis strategies are not the norm in most industries. It is not uncommon to see simple and preventable faults disrupt the operation of an entire integrated manufacturing facility. For example, faults such as malfunctioning sensors or actuators, inoperative alarm systems, poor controller tuning or configuration can render the most sophisticated control systems useless. Such disruptions can cost in the excess of $1 million per day and on the average they rob the plant of 7% of its annual capacity. Over the last decade the fields of multivariate statistics and data visualization and analysis methods have merged to develop powerful sensing and condition-based monitoring systems for predictive fault detection and diagnosis.These methods rely on the notion of sensor fusion whereby data from many sensors or units are combined with process information, such as physical connectivity of process units, to give a holistic picture of health of an integrated plant. Such methods are at a stage where these strategies are being implemented for off-line and on-line deployment. This article attempts to outline the field of sensor fusion - the application of signal processing methods, in the temporal as well as spectral domains, on a multitude and NOT singular sensor signals to detect incipient process abnormality before a catastrophic breakdown is likely to occur Keywords: Process analytics, process and performance monitoring, multivariate statistical analysis, sensor-fusion

Sep 1, 2012

By Aziza A. Yousef, Suzan S. Ibrahim, Mahmoud A. Arafa, Mohamed A. Abdel Khalek

In view of the shortage of soft water all over the Middle East countries, seawater may be used to replace the fresh water in flotation beneficiation. The flotation process required about 7 m3 of fresh water/ ton ore. This article aimed to study the effect of seawater cations and anions on the flotation process of four important mineral commodities. The adsorption of collector, zeta-potential, zero point of charge and floatability of pure minerals were studied. The individual effects of different cations and anions that are predominant in seawater, within their more or less actual concentrations were studied on individual mineral and on groups of them. The troublesome Ca2+ and Mg2+ ions, in the anionic circuit could be controlled by soda ash addition to the pulp before the anionic collector. The addition of sodium silicate improved the floatation selectivity of mineral mixtures and natural ore. At the optimum conditions the calcareous phosphate ore yielded a concentrate recovery of 83% with a grade of 34% P2O5, with 0.61%MgO, which from an ore assaying (25.3% P2O5 and 9.4% MgO).

Jan 1, 2003

By Bernard B. Vannoy, Howard W. Gault, Ramesh Bobba

"Treviicos-Soletanche Joint Venture (JV) and the US Army Corps of Engineers (USACE) have installed a 3800-foot long, 275-foot deep and minimum 2-foot wide secant pile barrier wall at Wolf Creek Dam in Jamestown, KY. This paper describes the methodology employed by the JV and USACE to evaluate the overlap, thickness, and position of the barrier wall. It addresses the contractual requirements, positional uncertainty, and evaluation procedures.These procedures evolved over the course of the project as various issues were identified and procedures developed to evaluate these issues. During the project, it became clear that the JV and USACE could ascertain that the wall thickness and overlap requirements could be met if the overlap based upon Koden data was at least 0.7’ in the left-right direction. For a small number of piles with overlaps between 0.5’ and 0.7’, the piles are contractually compliant yet contain a minor degree of uncertainty in the overlap. Initially, the USACE assumption was that the amount of uncertainty of verticality measurements would require more than a 1-foot measured overlap in the left-right direction to confirm an actual, contractual 6-inch overlap. With time and experience, the limit of measured overlap was reduced in accordance with greater understanding of the equipment capabilities and tolerances. Other lessons learned include the need for Quality Control/Assurance personnel to collect data at the same starting point for every pile.For every pile the JV and USACE compared analog and digital data to provide confidence that the correct digital data was used for overlap calculations. Perhaps the most important lesson learned was the importance of the JV and USACE working together and sharing all data. Overlap analysis was performed by the JV’s Barrier Wall Specialist and a small number of USACE personnel. This resulted in a high level of experience and expertise within a small group.IntroductionThe Treviicos-Soletanche Joint Venture (JV) and the US Army Corps of Engineers (USACE) have installed a 3800-foot long, 275-foot deep, and minimum 2-foot wide secant pile barrier wall at Wolf Creek Dam in Jamestown, KY. The wall was installed through a 6-foot wide Protective Concrete Embankment Wall (PCEW) which was installed two feet into rock. The PCEW protects the embankment from erosion of drilling fluids during subsequent operations. Below the PCEW the piles were installed to a specified elevation (staggered at 475’ and 473’ below the 748.2’ work platform). The Ordovician limestone and shale bedrock is flat lying with few vertical fractures. These conditions facilitate the advancement of pilot holes with very low deviations (with considerable credit to the JV’s drillers and steering engineers). The pilot holes were spaced on 31.5-inch and 35-inch spacing. Subsequent enlargement of the pilot holes to 50’ resulted in a continuous wall. This paper addresses the requirements and procedures to assure that the wall was as wide, deep and continuous as specified."

Jan 1, 2015

By Joan Weinberg

The real gross national product (GNP) expanded by 2.3% during the second quarter, down from the anomalous 4.4% growth rate in the previous 3 months. If the expansion continues through October, it will have lasted 5 yr and become the second longest in 40 yr.2 As in the first quarter, improvement in U.S. exports played a role in the continuing--albeit slow--growth. More than 2 yr of declines in the dollar relative to currencies of other industrial countries have contributed to a slight reduction in the trade deficit in real (volume) terms, as real net exports of goods and services rose $1.9 billion (table 1). Exports grew a strong 12.1% while imports, which had fallen the previous two quarters, rose 7.4%. Manufactured goods and petroleum products accounted for most of the second quarter import increase. The American Petroleum Institute estimates that the volume of crude oil and refined products imports in the first half of 1987 surpassed those in the same period last year by 7.5%, reflecting falling domestic production and higher than expected demand. Expenditure on durable goods--those that last at least 3 yr-by both consumers and producers also contributed to the second quarter expansion. Personal consumption of durable goods rose 9.0%, after having fallen the two previous quarters. Motor vehicle purchases accounted for most of the second quarter increase and the first quarter decrease. Sales of automobiles surged in the last quarter of 1986, as consumers rushed to capture the sales tax deduction that was eliminated on January 1. Sales fell in the first quarter of 1987, but have now moved closer to the trend line exhibited in the first three quarters of 1986. Automobiles accounted for half the 0.8% July gain in retail sales, and two-thirds of the 1.4% June gain. Producers durable equipment purchases also rose this quarter, accounting for the increase in nonresidential fixed investment.

Jan 1, 1987

By S. C. Howell

The mining of taconite, to provide feed for a processing plant, requires that the flow of material continue uninterrupted. This means first, that the crude must be of a size acceptable to the primary crusher in order to reduce the delays caused by plugging the crusher with chunks. Secondly, elimination of oversize in the pit will reduce costs of all wear parts used in the mining and processing of taconite. Savings in wear parts is readily recognized in dipper teeth, bases, buckets, truck boxes, and crusher parts, both primary and secondary. During the early days of taconite mining, it was soon recognized at reserve mining company's Babbitt operations that experience in mining other ores was not always (or ?necessarily??) Applicable to excavating taconite. This was especially true in drilling and blasting. Blasting of small tonnages in single or double rows simply filled the pit with scattered chunks and provided very shallow banks for shovel loading. It also created problems for the jet piercers, since all drilling had to be performed in fractured areas. Drilling efficiency suffered and costs were extremely high. Shovel and truck efficiencies were also low and again costs were high. A high percentage of secondary breakage was required. This necessitated the use of numerous man hours to jackhammer holes in chunks, preparatory to loading and blasting. After the chunks were reduced, bull- dozer and grader hours were needed to pile the taconite for acceptable shovel loading.

Jan 1, 1968

By Kenneth N. Pike

The need to comply with environmental regulations and increase production has resulted in modifications to the East Penn blast furnace operation. Changes made include furnace design modifications, closed loop water cooling with heat recovery, automated weighing and charging, automated tuyere punching, ammonia scrubbing of tail gases and improved metal and slag handling to minimize environmental impact. These changes have resulted in a marked increase in yearly production and compliance with many of the air, water and solid waste regulations.

Jan 1, 1990

By Michael E. Stout

M.A. Industries, Inc. has developed and is now offering on a commercially available basis, complete systems to recover and recycle lead from spent SLI batteries. The system begins with the breaking and separation of the component parts of the batteries and subsequent treatment of the effluent water produced by this operation. The recyclable materials recovered from this process are metallic lead, lead paste and polypropylene. The lead paste is introduced into a process to convert it from a lead sulfate to a lead carbonate. The process also regenerates the salt solutions into reusable carbonate. The lead carbonate is then leached into an acid bath where it is later recovered by a proprietary electrolytic process. The metallic lead is recovered in a short rotary furnace producing metal for further refining and alloying. The polypropylene is further washed and then introduced to a reclaim extruder along with the proper modifiers and additives. The resulting resin can then be sold on the open market to injection molding processors. This complete system greatly reduces the amount of waste to be disposed of and completely complies with all applicable EPA guidelines.

Jan 1, 1993

By Ullrich Kammer

Metaleurop's secondary lead smelter at Oker produces 60.000 mtpy of lead and lead alloys. More than 8O2 % of the raw materials are spent lead acid batteries. The other 2O2 % consists of drosses, ashes, scrap lead, type metal, sludges, etc., and is processed in a short rotary furnace (SRF). Also, industrial batteries not fitting in the battery scrap treatment plant are processed in the SRF provided with gas/oxygen-burner. Till Sept. 199O2, a soda ash slag was used in the SRF-smelting similar to the rotary kiln-smelting at Oker. Facing the future problems of handling and dumping soda ash slag, Harz-Metall GmbH has improved SRF-smelting with a non¬hazardous slag, insoluble in water, easy to dump and cheap in fluxes. This slag is based on a CaO-SiO2 -Fe0-type. Aim of the slag smelting is to be within the temperature range of 2 1100° and 1200°C - the eutectic line of Olivine in the corresponding ternary system. Since Sept. 199O2 Harz-Metall GmbH has operated the SRF with an "Olivine-type slag" with good results. Although the material is a "leady" slag. HMG is optimistic of using it as a filling material for construction purposes.

Jan 1, 1993

By A. A. Novoselov, U. Kelm

"Large volumes of mine tailings accumulated in surroundings of porphyry copper deposits represent a growing threat to environment. They contain significant concentrations of toxic metal and metalloids which can contaminate river runoff, ground waters or can be transported by wind. Both extreme pH of fluids in tailings impoundments and high surface areas of processed mineral grains provide their increased reactivity. As a result, during only a few decades, As, Cu, and Mo can be mobilized, redistributed through the tailing column and accumulated through post-deposition leaching, evaporation and contamination with natural fluids. Those processes are reflected in the forming of secondary minerals. Gypsum, Fe oxides/hydroxides, efflorescent salts and clay minerals are typical alteration products in tailings. Here we present the results of reactive transport simulations implemented on the base of PHREEQC and SUTRA codes. The one-dimension model emulates the mass balance between rainfall, evaporation and subsurface runoff, the kinetically- and thermodynamically-driven dissolution of tailing minerals, advective and diffusive transport of tailing fluids, and precipitation of secondary phases. A typical tailing column is composed of four unequal layers with predominance of (i) evaporation, (ii) secondary mineralization above, (iii) below water table, and (iv) near the bottom of dump. Those horizons are characterized by contrasting pH, chemical composition and bulk mineralization of pore fluids, distinct accessibility of atmospheric oxygen and, as a consequence, distinct intensity of sulfide oxidation. The modeling and its verification on Chilean tailings impoundments reveal the complexity and high rates of secondary mineralization. The accumulation of toxic alteration products is controlled by fluid transport through the tailing column induced by both rainfall/evaporation and exchange with subsurface runoff. The geochemical modeling is a powerful approach which allows comparing the processes in tailing deposits produced by distinct flotation regimes and providing the long-term predictions of their environmental impact as well as identifying sectors of tailings for possible re-processing."

Jan 1, 2018

By E. Guerrini, M. Maccagni, J. Nielsen

"Lead is the most important material able to meet the current demand for energy storage. The lead acid battery is reliable, efficient and inexpensive. Continuous developments in battery construction are providing improvements in all aspects of the batteries’ performance. The lead acid battery is both the main lead product and the main raw material for lead production. More than half of the lead produced is from secondary smelters where batteries are the most important feed material. The environmental pressure on lead production has been increasing for many years, and continues to become stronger and stronger. The lead production processes and technologies themselves will require updating to meet the new regulations. Although they are very strict now, they will become even more so and current technologies may not be sufficient. Because recyclability is a strong point for the lead acid battery, the secondary smelters need to reduce the environmental impact as much as possible. In recent years, the secondary smelters underwent impressive changes in this direction, but some more improvements are possible. Electrochemistry can offer a step change improvement in making secondary lead production more environmentally friendly. Engitec has developed an electrochemical process base on a very high current density (high productivity) cell using an inexpensive electrolyte and at a relatively low cost. In this paper, the latest update on the technology is provided. INTRODUCTION The lead acid battery is considered the “walking dead” by some new technologies trying to replace it. It has played and will continue to play a very important role in our lives because it is inexpensive, fully recyclable and the existing lead and the mine reserves guaranty enough material for the extended future. According to the life cycle, the lead acid battery is the cheapest and the most effective system to store energy. Lead is practically a close loop where lead battery production consumes more than 80 % of the produced lead but contemporarily it is the most important raw material for the production of metallic lead. In fact, nowadays, the secondary production has overcome primary production and this trend is expected to continue. Primary lead is the make-up material for the existing battery production and the source of lead for the construction of the new ones."

Jan 1, 2018