Search Documents

By G. M. Martinez

The Bureau of Mines has investigated methods for the recovery of byproduct heavy minerals from sand and gravel operations in Oregon and Washington. These heavy minerals are not currently recovered except for gold in a few areas. The recovery of byproduct heavy minerals would provide a domestic source of minerals presently imported, and a more efficient use of domestic resources would be accomplished. Samples from more than 40 locations were treated by gravity separation to yield heavy mineral concentrates (black sands). Magnetite, ilmenite, zircon, rutile, chromite, platinum-group minerals, radioactive minerals and gold were identified in the concentrates. Individual zircon, ilmenite, chromite; magnetite, and gold products were recovered from selected concentrates by low-and high-intensity magnetic, high-tension, and heavy-medium separation techniques. The recovery for the individual mineral products ranged from 67 to 95 pct.

Jan 1, 1981

By D. R. Tesarik

The factor of safety, the traditional measure of stability for earth embankments, is graphically presented in factor of safety charts in this Bureau of Mines report. Factor of safety contours are drawn for homogeneous earth embankments for two contrasting situations: (1) no phreatic surface and (2) a phreatic surface that assumes 10-pct freeboard. The factor of safety can be read directly from the charts if the physical properties of the soil and the geometry of the embankment are known. The curves provide a quick first approximation of the "most stable" and "least stable" condition of the embankment. The Simplified Bishop Method was used for the safety factor calculations, and a sequence of least squares curve fitting steps was used to present the factor of safety in final chart form.

Jan 1, 1981

By G. A. Savanick

The Bureau of Mines has designed, fabricated, and field tested a water jet cutting device capable of perforating nonmetallic well casings for the purpose of completing or stimulating in situ uranium leaching wells. The device is lowered into the wellbore, where it issues a high-velocity water jet that penetrates either a polyvinyl chloride or fiberglass casing, cement, and from 1 to 4 feet into the surrounding uraniferous sandstone. The resulting perforations allow leaching solution to pass between the sandstone and the wellbore. This report describes the water jet perforator, tells how it is used, presents cost data, and discusses the results of laboratory and field tests. The tests were designed to (1) determine the optimum operating conditions for water jet perforation, (2) assess the effects of changes in these conditions, (3) evaluate the performance of the water jet perforator under actual conditions, and (4) compare this method with other methods of well completion. These tests showed that water jet perforation is superior to conventional well completion methods for selectively achieving communication between the well-bore and adjacent sand while maintaining sand control, for restoring permeability lost through wellbore damage, for stimulating poorly performing wells for completing wells with casings that have inside diameters as small as 2 inches, and for extending the effective well diameter.

Jan 1, 1981

By J. J. deBarbadillo

This Bureau of Mines report describes a process for recovering chromium and other metals from superalloy scrap. Laboratory-scale experiments were conducted to test a complex flowsheet utilizing a wide range of extractive metallurgical operations. The novel basis for the process is the fonnation of a sulfide matte in which chromium is concentrated in a discrete chromium sulfide phase. Mineral processing and hydrometallurgical procedures are used to separate chromium sulfide from the other matte constituents. The products of the process are a chromium-nickel alloy suitable for reuse in the superalloy industry, electrolytic nickel, electrolytic cobalt, and iron-molybdenum residue. Recovery of the principal elements contained in the scrap is chromium--93 percent, nickel--99 percent, cobalt--96 percent, and molybdenum--92 percent.

Jan 1, 1981

By W. L. Falke

The Bureau of Mines has developed a system that permits the "soft" soldering of aluminum and aluminum alloys with standard tin-lead solders. The method employs application of a thin nickel-copper-alloy coating to the substrate, which enables the tin-lead solders to wet readily and spread over the areas to be joined. With conventional technology, aluminum and aluminum alloys are extremely difficult to solder because tenacious surface oxide films prevent wetting. With the Bureau-developed method, the aluminum substrate is mechanically or chemically cleaned to facilitate bonding to a minute layer of zinc that is subsequently applied with an electroless zincate solution. The nickel-copper-alloy (30 to 70 pct Ni) coating is then applied electrolytically over the zinc, using immersion cell or brush-coating techniques. Development of acetate electrolytes has permitted deposition of the proper alloy coatings. The coated areas can then be readily joined with conventional tin-lead solders and fluxes. The joints so formed are ductile, strong, and relatively corrosion resistant, and exhibit strengths equivalent to those formed on copper and brass when the same solders and fluxes are used. The method has also been employed to soft-solder magnesium alloys.

Jan 1, 1983

By Kim B. Shedd

The U.S. Bureau of Mines Particulate Mineralogy Unit examined the habits of six zeolite minerals commonly occurring in domestic zeolite deposits. Mineral habit is of interest because current theory on the potential for sarcoma production in test animals emphasizes the size and shape of mineral particles, without regard to composition or structure. A scanning electron microscopic study revealed that, of these six minerals, only mordenite and erionite crystallized in acicular to fibrous habits, The fibrous varieties of these two minerals were characterized by size and shape on the transmission electron microscope, and their dimensions were compared with those of asbestos and amphibole cleavage fragments. When comminuted, these two minerals possess "fibrosity indices" similar to those of amphibole cleavage fragments. One sample, a rare woolly erionite, has uniform widths, large aspect ratios, and a "fibrosity index" similar to those of asbestos.

Jan 1, 1982

By D. E. Kirby

In line with the Bureau of Mines' goal of providing technology to maintain a supply of minerals adequate to meet national economic and strategic needs, a method for recovering chromite from lateritic materials was investigated. Laterites are a large resource of Ni, Co, and Cr, critical metals of which the United States has insufficient domestic sources. A roast-leach method was developed by the Bureau to extract nickel and cobalt from domestic laterites. A concurrent effort was made to recover chromium from either unprocessed laterites or the leach residues. This report characterizes laterites and laterite leach residues. It describes a chromite recovery procedure using conventional industrial beneficiation equipment for sizing, low-intensity magnetic separation, and gravity concentration. Concentrates containing 20.0 to 22.4 pct Cr (29.0 to 32.7 pct Cr203) and with a 1.6:1 to 1.9:1 Cr-Fe ratio were recovered from laterites and residues containing 1.3 to 2.5 pct Cr with recoveries exceeding 50 pct. Because of their low grade and fine size, these concentrates would be suitable for preparing chromium chemicals. The direct beneficiation of laterites for chromite recovery resulted in the minerals containing nickel and cobalt concentrating in slime products. No iron oxide coproducts of acceptable grade were recovered from either laterites or residues.

Jan 1, 1982

By Robert W. Waytulonis

The Federal Bureau of Mines contacted 29 organizations--mine maintenance departments and equipment manufacturers--concerning service experience and construction of diesel exhaust-gas water scrubbers. Scrubbers are used primarily on mobile diesel-powered mining equipment subject to 30 CFR 36. Because the scrubbers cool exhaust gas and act as flame arresters, their failure would compromise safety in underground mines. Scrubber maintenance problems and frequency and modes of failure were identified, and construction materials and techniques were evaluated. Three failed scrubbers were randomly selected from two cooperating mines, and their modes of failure were determined. In conjunction with failure analyses, mine water and scrubber water solution samples were chemically analyzed to characterize corrosive properties. Sludge and mineral deposits and different types of corrosion and metal fatigue were identified as problems leading to scrubber failure. The corrosion process is explained; maintenance practices, construction materials, and manufacturing methods that could be used to reduce premature failures and allow longer effective scrubber life are identified; and basic changes in scrubber design are suggested. If type 304 stainless steel is used throughout the scrubber and regular maintenance is performed, long, dependable service can be expected. Other materials such as 304L, 316, or other more exotic steel alloys may be necessary under certain conditions.

Jan 1, 1982

By William H. Pomroy

The Bureau of Mines, through a 4-year program of combined in-house and contract research, has developed the necessary hardware and software technology to provide rugged, reliable automatic fire protection for surface mining mobile equipment. One element of this program was a continuing effort to help foster rapid mining industry acceptance of the technology by keeping end user costs reasonable. This report is an analysis of the economic impact of surface mining mobile equipment fires and the cost benefit of utilizing automatic fire protection systems to abate these losses.

Jan 1, 1982

By Richard J. Mainiero

The Bureau of Mines conducted research to evaluate the optimum design for a rock-breaking explosive charge that could be fired unconfined in a gassy or dusty coal mine without the danger of igniting the flammable atmosphere. Charges of various shapes, with and without cavities, were tested in a gallery using 3-by 3-by l-ft concrete blocks as simulated boulders. For these tests the optimum charge, in terms of cost, weight, and convenience in handling, consisted of a flat l-1/2-lb charge of permissible explosive seven-eighths of an inch thick and 7 in in diameter encased in a l/2-in thick layer of fine salt (NaCI). This work demonstrated that it should be possible to produce an inexpensive explosive rock-breaker charge that would be safe to use in underground coal mines.

Jan 1, 1982

By Sterling J. Anderson

To define the technical competence and capabilities of a nonexplosive excavation concept, the Bureau of Mines conducted reduced-scale laboratory tests of a mechanical excavation tool called a rock splitter. Hydraulically actuated splitters, capable of generating both radial and axial loads on a predrilled hole, were designed and fabricated. Through paired variable testing and drifting simulation, reduced-scale splitter performance was evaluated in concrete. Testing proved that the rock splitter is capable of excavating within the highly confined drift set-ting and that it offers a distinct advantage over splitters that can generate radial loads only.

Jan 1, 1982

By L. W. Higley

It is estimated that well over 20 million lb of chromium and 8 million lb of nickel, plus other metal values, are diverted annually to furnace dusts, mill scale, and contaminated swarfs in the domestic stainless and other specialty steelmaking industry. Little inroad has been made toward the in-plant recycling of these wastes to reclaim the metal values. The Bureau of Mines has devised a process for recovering about 90 pct of the chromium and molybdenum and well over 90 pct of the nickel and iron from stainless steelmaking furnace dusts, swarf, and mill scale. Other metals such as manganese are also recovered. Initial laboratory results were confirmed and expanded to include a wide variation of stainless steelmaking waste mixtures. Later experiments have included specialty steelmaking wastes other than from stainless steelmaking. Significantly, the ease of technology transfer has been demonstrated by a number of industrial-sized (19-ton) commercial electric furnace heats, in which the pelletized wastes represented some 10 to 20 pct of the furnace charge, replacing part of the normal scrap charge. Results of these successful large-scale trials are presented. Some information is also presented on incorporation into the pellets of chromium-bearing particulate wastes originating from other than steelmaking production. Cost evaluation indicates the process is economically attractive.

Jan 1, 1982

By Theodore L. Turner

This Bureau of Mines report describes calcination of kaolinitic clay in a direct-fired 2-1/2- by 24-ft rotary kiln at 750° and 775° C. Methods for preparing kaolin feed materials and characterization of calcined products are discussed. Approximately 99 pct of the alumina in a typical eastern Georgia kaolin was soluble in HC1 after calcination at either 750° or 775° C.

Jan 1, 1982

By Roy C. Bartholomae

This Bureau of Mines report presents the results of a laboratory investigation of coal cutting mechanics and noise. These experiments were performed using linear cutting apparatus that operates over a broad cutting speed range. The influence of several coal cutting parameters on the noise, force, productivity, and specific energy associated with linear cuts was ascertained. Some basic theoretical aspects of coal cutting mechanics and noise generation are discussed, and the results of the laboratory experiments are used to formulate analytical models of the coal cutting forces and noise. The analytical model for coal cutting noise is then generalized to account for the more important effects of rotary cutting. Based on the generalized model, an estimate of the sound pressure level at an operator's position is made for a typical continuous mining machine. It is concluded that by employing linear rather than rotary cuts, using deeper depths of cut, slower cutting speeds, and more efficient cutting tools, it is possible to reduce the level of coal cutting noise, as well as provide benefits to other important areas of health and safety in underground mining.

Jan 1, 1983

By R. S. Olsen

The Bureau of Mines is engaged in research to recover aluminum from kaolinitic clay and other nonbauxitic domestic resources. As part of this work, calcined Georgia kaolin was prepared by a process that prevents slime formation and makes the leached residues fast settling and easy to filter. The leaching reaction for calcined kaolinitic clay in a 5 pct stoichiometric excess of boiling 23-to 26-pct HCI was found to be zero order. Rate constants based on the weight-fraction of aluminum in the clay were found to be between 0.095 and 0.15 min-1 depending on feed preparation and leaching parameters. The mathematical relationships between aluminum extraction and time for both batch and continuous, stirred-tank operations were derived and verified experimentally.

Jan 1, 1983

By David A. Larson

Preliminary laboratory experiments have been conducted by the Bureau of Mines to define the influence of bit geometry on methane ignitions as a step toward establishing safer mining-machine operating parameters. The experimental system was designed to simulate the operation of a continuous mining machine, using a drum-type cutterhead of normal diameter with a narrow cross section, permitting full-diameter drum cutting tests to be run on material representative of sandstone lenses (or inclusions) in coal seams. Two conical bit types were tested at shallow depths of cut with three drum speeds. Bits that rotated in the mounting block during testing did not produce ignitions. The ignition frequency for used bits was three to four times greater than for new bits at the same kerf depth.

Jan 1, 1983

By William C. McBee

Sulfur concretes have been developed by the Bureau of Mines as construction materials with physical and mechanical properties that suit them for use in acid and salt corrosive environments where conventional concretes fail. Mixture design methods were established for preparing sulfur concretes using different types of aggregates and recently developed mixed-modified sulfur cements Bench-scale testing of the sulfur concretes has shown their potential value. Corrosion resistance, strength, and durability of sulfur concrete are superior to those of conventional materials. Field in situ evaluation tests of the sulfur concretes as replacement for conventional concrete materials are in progress in corrosive areas of 24 commercial chemical, fertilizer, and metallurgical plants.

Jan 1, 1983

By Dwight L. Sawyer

To provide technology that can help decrease the dependence of the U.S. aluminum industry on imported bauxite, the main ore of aluminum, the Bureau of Mines is investigating the extraction of aluminum from abundant domestic reserves of kaolinitic clay. Miniplant studies of the continuous leaching of calcined kaolin with boiling 25-pct HC1 acid resulted in a 93- to 99-pct extraction of the acid-soluble alumina in the calcined kaolin feed. Data are presented for an acid leaching study carried out in three or four continuously stirred tank reactors (CSTR) in series, feed rates of 100 to 250 lb/hr of calcined kaolin, and total nominal residence times of 0.7 to 2.3 hr. A material balance for a 176-lb/hr calcined kaolin feed rate in a circuit consisting of three reactors, four classifiers, and five thickeners is given. Data provide detailed compositional and physical information for calcined kaolin, process liquors, and acid-leached residue solids.

Jan 1, 1983

By Wallace W. Roepke

The Bureau of Mines conducted a series of experiments using Illinois No. 6 coal to determine the effect of asymmetric wear on airborne respirable dust (ARD), specific energy, cutting force, and normal force. Plumb-bob-type bits--one new bit and four ground with different sized flats--were used. Constant-depth linear cuts at 0.32, 0.64, 1.27, and 2.54-cm cut depths were made. Both cutting force and normal force increased as the flat area increased. Specific energy demonstrated a statistically significant increase with flat area at the 0.32-and 1.27-cm cut depth only. Specific ARD showed a statistically significant decrease with increasing flat area only at the 0.64-cm cut depth. Increasing cut depth increased cutting force but decreased specific energy and specific ARD. Normal force increased with increasing cut depth for the new bit but exhibited a maximum at 0.64 cm for the bits with flats.

Jan 1, 1983

By D. K. Steele

An 18-in-diam column water elutriator was designed, tested, and operated by the Bureau of Mines for recovering nonferrous mixed metals from automobile shredder rejects. The waver elutriator separated metals from nonmetals contained in shredded nonmagnetic rejects. The unit was constructed and integrated into a local automobile shredding operation. Nonmagnetic rejects from the automobile shredder were fed onto the surface of a column of rising water. Dense materials fell through the rising water and were collected as a sink product at the bottom of the column; medium-density materials were removed as an intermediate product in a water flow through a discharge port located between the overflow and sink; and light materials were immediately carried out in the overflowing water at the top of the column as a float product. Nearly 99 pct of the mixed metals were recovered from the nonmagnetic rejects as a 70-pct-metal concentrate. Other operating conditions yielded a 93.7-pct-pure-metal product resulting in a 93.1-pct metal recovery. Float rejects are combustibles, light plastics, foam rubber, and minimal amounts of coated and uncoated copper wire. The middling discharge contained mainly medium-density rubber, plastics, glass, rock, coated and uncoated copper wire, and frequently some thin-sheet stainless steel and wrought aluminum. Maximum metal recovery in the operating program was achieved using a water velocity of 52 fpm (650 gpm). Maximum purity was obtained with a velocity of 88 fpm (1,100 gpm). .Water was recycled through a 12,000-gal baffled clarifying tank. Entrainment water losses with the float and middling rejects averaged 50 gpt of reject feed. Records maintained by the shredder operator show a 34-pct increase in nonmagnetic metals recovery during a 1-yr operation of the water elutriator as compared to recoveries from a previously used air classification system.

Jan 1, 1983