Search Documents

By D. E. Traut

A fluidized countercurrent ion-exchange system was developed, operated, and evaluated by the U.S. Department of the Interior, Bureau of Mines. The system consisted of integrated multiple-compartment absorption and elution columns in which the solution flows were continuous except for short periods when resin increments were withdrawn. The exchange of uranyl carbonate between a simulated in situ uranium leach liquor and a strong-base ion-exchange resin together with the subsequent elution with an ammonium chloride solution was studied. The effects of the number of sections, section height, amount of resin withdrawal, solution flow rate, and column diameter were investigated. The kinetic and equilibrium relationships for the absorption and elution steps were also examined. The experimental data indicate a strong interdependence between variables. Solution retention time appears to be a major limiting variable in the absorption process, while resin residence time is the determining factor in the elution process. The column was efficient over a range of conditions, but close control was needed for optimum operation.

Jan 1, 1978

By B. T. Brady

Recent theoretical, experimental, and field studies conducted by the Bureau of Mines suggest that rock failures may be predicted and, in some instances, controlled. Theoretical studies that were later corroborated by laboratory and field studies predict that a seismic anomaly will precede rock bursts and/or roof falls in mines. The seismic anomaly is predicted to consist of an increase in the number of seismic events occurring in the immediate vicinity where the failure 1s nucleated. This increase will then be followed by a dramatic decrease of seismicity in a broad region that surrounds the location of the impending failure. The dimensions of this region allow a preliminary estimate of the time to failure (measured from the time the seismicity increase began) as well as an estimate of the energy that will be released at the instant of failure. Field observations indicating that this predicted behavior does precede rock bursts and a roof fall are presented in this report. Implications of results to the problem of failure control in mines that experience massive rock failures are discussed.

Jan 1, 1978

By H. W. Kilau

The Bureau of Mines used a high-temperature rotational viscometer to test basic oxygen furnace slags to determine fluorspar requirements and to evaluate colemanite and fused boric acid as substitute fluidizers. A continuous technique of viscosity measurement was adapted to better determine the viscosity-temperature profiles of volatile fluorspar slags. Criteria used for estimating slag fluidizer effectiveness were (1) the apparent solidification temperature, and (2) the temperature range of slag crystallization. Colemanite and fused boric acid in high-basicity slag were superior fluidizers to fluorspar when compared on the basis of boron versus fluorine concentration. Fused boric acid was nearly equivalent to ceramic-grade fluorspar when compared on a simple weight basis, while colemanite was inferior to fluorspar. Fluorspar slags volatilized fluorine during viscosity testing. Colemanite and fused boric acid slags were stable, no boron losses being detected. A fluidizing limit was found for fluorspar at 2.9 percent fluorine concentration; higher concentrations impaired viscosity and caused foaming and crusting of slag. Concentrations of boron up to 4.4 percent resulted in very fluid slags with no fluidizing limit.

Jan 1, 1978

By Frank G. Horino

Drill cores from 18 exploratory holes that were drilled into the unleached saline beds were tested for mechanical properties by the Bureau of Mines. Test cores were primarily selected from zones L4B, R4B, L3, and R3A in the Piceance Creek Basin, Rio Blanco County, Colo. Regression analysis techniques were tried in an attempt to relate kerogen yield or apparent specific gravity to the parameters compressive strength, Young's modulus, and Poisson's ratio. Correlation coefficients were very poor, indicating that this type of analysis was not amenable to these data. Analysis of variance techniques were tried using a division of either greater than or less than 10% nahcolite together with the requirement of less than 3% dawsonite. Results showed that a larger percentage of nahcolite tended to lower the compressive strength and to increase Young's modulus. A second analysis was made using a division of less than 3% dawsonite and greater than 3% dawsonite together with the requirement of less than 1% nahcolite. For this analysis, a larger per-centage of dawsonite tended to increase compressive strength, Young's modulus, and Poisson's ratio. Mean compressive strength values were determined for the mining horizons of interest. Average physical properties for design purposes were also determined for the horizons of interest and for a proposed adit based only on logged geologic depths to these horizons. No consideration was given to percentages of nahcolite and dawsonite. Creep data obtained from nahcolite-and dawsonite-rich oil shales provides a best fit to a modified power equation.

Jan 1, 1978

By Raymond F. Farrell

A goal of the U.S. Department of the Interior, Bureau of Mines, is the advancement of minerals technology through the development of improved metals and minerals processing. In support of this goal, the Albany Metallurgy Research Center has developed atomic absorption spectrographic methods for the rapid analysis of A1203, CaO, Fe203, MgO, MnO, and Si02 in steelmaking slags. The application of these methods is discussed using an inexpensive pressure dissolution system. The overall coefficient of variation is 5 pct. The accuracy is the same as the reproducibility.

Jan 1, 1979

By T. L. Marchewka

As part of its program to conserve the Nation's natural resources by developing improved performance materials, the Bureau of Mines, U.S. Department of the Interior, in cooperation with the U.S. Department of Energy, has conducted an investigation of materials of construction able to withstand the high temperature and hostile environments encountered in coal gasification units. Refractory pipe liners are required when extremely hot gases or abrasive solids are transported between processing units in the gasification plants. One promising technique for producing refractory pipe (or refractory pipe liners) is centrifugal casting. For this study, the effect of processing variables such as workability, additives, reinforcement and spinning time, and centrifugal force were evaluated using four commercial refractory concretes. In addition, data on characteristics such as strength, density, abrasion, and spalling resistance of 5-inch-diam refractory pipe were developed. Techniques for forming large-diameter (19-inch) refractory pipe also were evaluated. The test results indicated that all four refractory concretes could be made into strong, homogeneous pipe, but that optimum casting parameters had to be determined for each specific composition. The investigation revealed that the major controlling factor in the production of the centrifugally cast pipe was the workability of the refractory concrete.

Jan 1, 1979

By J. L. Holman

The Bureau of Mines has extended its previous development of cast Mn-Cu damping alloys to powder metallurgy (P/M) consolidation of alloys containing 55 to 75 wt-pct Mn. Blends of minus 200-mesh elemental powders were compacted cold in directional and isostatic presses. With 1 pct binder, typical green densities ranged between 76 and 80 pct of theoretical when pressing at 30 or 48 tsi. Green strength increased with compacting pressure and copper content. As-sintered tensile strengths ranged to 60,000 psi fox a hydrogen, sintered 60Mn-40Cu alloy, along with 5-pct elongation. Sintered densities ranged between 90 and 96 pct of theoretical. Sintering (a as effective when holding for 1 hr at maximum temperatures of 900° to 1,040` C, dependent on composition. Strength and ductility were considerably lower than for equiva¬lent cast alloys. When aged to the damping condition, alloys containing 60 to 70 pct Mn exhibited >40 pct specific damping capacity (SDC) at 5,000-psi stress, considerably higher than values reported for equivalent cast material. Effects of 1 or 3 pct Sn or Zn additions on SDC and other properties were assessed. Trials were conducted on consolidating rings and gears of the 65Mn-35Cu alloy on industrial-type P/M equipment.

Jan 1, 1979

By Edward D. Thimons

The Bureau of Mines conducted in-mine tests to determine correction factors applicable to low-velocity airflows (below 150 fpm) measured by the smoke cloud, vane anemometer, and oil of wintergreen tracer gas techniques 0 The average correction factors found for these methods of measurement were lower than those reported in the literature for use with higher velocity measurements. All tests measured airflows with controlled average velocities ranging from 50 to 100 fpm. Correction factors averaged about 0.75 for readings taken by the centerline smoke cloud method, remotely controlled and stickheld center" line anemometer, and split traverse stick-held anemometer. For hand-held centerline anemometer and oil of wintergreen tracer gas readings, correction factors averaged about 0.67. Since special anemometers are needed to measure airflows in this low-velocity range, and since proper calibration of these anemometers is difficult and expensive, the use of anemometers for low-velocity measurement is imprac-tical. On the other hand, smoke and oil of wintergreen give results as con-sistent as those obtained with specially calibrated, low-velocity anemometers. Furthermore, they are easy to use and inexpensive.

Jan 1, 1979

By Jack Touseull

On November 15, 1972, the Bautsch mine, a lead-zinc mine in Paleozoic dolomites, experienced a massive rock failure involving 3 to 5 million tons. Because this failure was large and extended to the surface, it was included in the Federal Bureau of Mines investigations on "Massive Rock Failures." Analysis of the rock mechanics and mode of failure revealed that failure at the Bautsch mine was the result of the interrelationship of many factors. Factors related to the failure were found to be external and internal to the mining environment. Unlike internal factors, external factors were not apparent and, therefore, many external factors were investigated; some of which are not normally considered in rock mechanics analyses. External and internal factors determined to be of significant importance were: (1) precipitation, (2) fractures, (3) plastic clay layer, (4) topography, (5) rock alteration, (6) bedding, and (7) mining zone dimensions. Because of the conditions at the mine, failure could have been predicted without extensive instrumentation. Application of basic geologic and engineering principles to the internal and external factors could have predicted failure. Alternately, failure would, in all probability, have been delayed by years if, after 1962, mining had been curtailed in the area of failure.

Jan 1, 1980

By V. R. Spironello

The Bureau of Mines is involved in research directed toward the utilization of municipal solid waste. One of the primary objectives is the recycling of the magnetic fraction of municipal solid waste (raw refuse). This is consistent with one of the Bureau's goals, which is to minimize the requirements for mineral commodities by maximizing metals recovery from secondary domestic resources, In this investigation, cupola trials were made using combinations of refuse scrap with shredded automobile scrap under basic and acid slag practices. Furnace operating information and the behavior of alloying and tramp elements was obtained. The research showed that it is possible to utilize up to 60 percent refuse scrap in the cupola under basic practice and 30 percent under acid practice, Aluminum in refuse scrap, present in bimetallic cans, increased the recoveries of silicon and manganese charged to the cupola. Increased use of refuse scrap provided iron of lower sulfur. The alumina resulting from oxidation increased the slag volume. The aluminum and tin contents of the iron increased with increasing levels of refuse scrap in the charge. Lead was not a problem with respect to contamination of the iron. In basic practice, operation of the cupola was satisfactory since all slags were adequately fluid. In acid practice, operation became troublesome above the 45-percent level. Under both practices, the cupola iron melting rate decreased. Particulates in scrubber water and stack condensate samples contained lead, zinc, and tin, and the dust load increased. The tensile and transverse strengths of the iron produced under both practices are reported.

Jan 1, 1980

By S. D. Maksimovic

The use of vertical surface degasification boreholes with bleeder systems and the use of a timbered bleeder system to degasify gob areas were studied by the Bureau of Mines. This report describes three gob degasification studies conducted in the Pittsburgh coalbed. One study was conducted to determine the number of panels degasified with one large borehole. The study showed that the borehole provided degasification for three panels. Another study was conducted during the retreat of a 35-acre panel with a single-entry and a two-entry bleeder system and a large surface borehole. A major portion of methane emitted from the panel was carried away by the bore-hole, leaving the bleeder entries relatively free of methane. The last study was made to determine the effectiveness of a timbered bleeder system. The bleeder entries successfully degasified the gob area when enough entries were available and adequate pressure was available to force the air through roof falls.

Jan 1, 1980

By E. L. Litchfield

Four short-term studies of practical ignition problems were undertaken and completed during the course of the Bureau of Mines project "Development of Specifications for Intrinsically Safe Equipment." Conclusions were as follows: (1) the most easily ignitible mixture of propane-air in a PTB break flash apparatus is approximately 5.2 percent propane; (2) miniature lamp bulbs to be used in intrinsically safe circuits are about as incendive to coal dust-air as to methane-air and should be tested in gas mixtures containing about 7.0 to 7.5 percent methane; (3) the sodium amalgam contained in high-pressure sodium lamps does not present an ignition hazard for coal dust or methane, where the lamps contain no more than 30 milligrams of amal-gam; (4) the maximum allowable surface temperature of permissible electrical enclosures should remain at 150° C despite efforts by industry groups to raise the value to 200° C.

Jan 1, 1980

By J. S. Dunning

One Federal Bureau of Mines research goal, to minimize requirements for domestically scarce mineral commodities through conservation and substitution, can be accomplished by utilizing more abundant elements such as iron, molybdenum, and titanium. An example of this research is the study of precipitation-hardening, iron-base alloys containing molybdenum and titanium, as substitutes for the high-tonnage stainless steels that are high in imported nickel and chromium. The precipitation hardened iron-base alloys are strengthened by a dispersion of the ternary Laves phase, Fe2 (Mo, Ti). Aluminum and chromium additions changed the solid solubility limits of molybdenum and titanium in a-iron and affected the composition of precipitating phases. A baseline composition of Fe-7Mo-2Ti was selected to study the effects of aluminum and chromium additions on the precipitation-hardening mechanism and microstructure and was also used in studies of mechanical properties and oxidation resistance. The study yielded workable, precipitation-hardening alloys, with elevated temperature strengths equivalent to or superior to types 304 and 316 stainless steels. Chromium and aluminum additions in combination were more effective in providing oxidation resistance than either addition was alone.

Jan 1, 1980

By J. E. Schiller

The Bureau of Mines has investigated the surface charge of amphibole asbestos fibers and nonasbestiform cleavage fragments, as part of the Bureau's fundamental studies to provide new knowledge on the physical and chemical properties of the amphibole minerals. Microelectrophoresis was used to measure the electrophoretic mobilities, in water, of particles from six asbesti-from amphiboles and seven nonasbestiform amphiboles over the pH range of 5 through 9. The particles generally ranged in size from 2 to 5 µm wide by 10 to 30 µm long. The isoelectric point was determined for four of the minerals, and values were found to be between pH 3.5 and pH 5. The minerals studied had zeta potentials that generally ranged from -25 to -so mv in neutral solution. Attachment of colloidal positively charged AgI was also studied as a means of determining surface charge. Scanning electron microscopy of amphibole particles that had been in contact with aqueous AgI showed equal attachment of AgI to asbestos fibers and to cleavage fragments; the extent of AgI coating was the same for both. The electrophoretic mobilities of asbestos fibers were essentially the same as those of elongated cleavage fragments of the same aspect ratio (particle length divided by width). Blocky particles from both asbestiform and nonasbestiform specimens had lower mobilities.

Jan 1, 1980

By David E. Siskind

The Bureau of Mines studied airblast from surface mining to assess its damage and annoyance potential, and to determine safe levels and appropriate measurement techniques. Research results obtained from direct measurements of airblast-produced structure responses, damage, and analysis of instrument characteristics were combined with studies of sonic booms and human response to transient overpressures. Safe levels of airblast were found to be 134 dBL (0.1 Hz), 133 dBL (2 Hz), 129 dBL (6 Hz), and 105 dB C-slow. These four air-blast levels and measurement methods are equivalent in terms of structure response, and anyone could be used as a safe-level criterion. Of the four methods, only the 0.1-Hz high-pass linear method accurately measures the total airblast energy present; however, the other three were found to adequately quantify the structure response and also represent techniques that are readily available to industry. Where a single airblast measuring system must he used, the 2-Hz linear peak response is the best overall compromise. The human response and annoyance problem from airblast is probably caused primarily by wall rattling and the resulting secondary noises. Although these will not entirely be precluded by the recommended levels, they are low enough to preclude damage to residential structures and any possible human injury over the long term.

Jan 1, 1980

By Robert Blickensderfer

Equipment and procedure for the continuous roll bonding of metal strips are described. The reels, mill rolls, and furnace were located within a vacuum chamber capable of operation at a residual gas pressure of 1 x 10-4 to 1 x 10-5 torr. Several metals were successfully clad at rolling temperatures of 930° to 1,050° C in lengths up to 120 ft. The bimetals that were clad included stainless steel to carbon steel, molybdenum and nickel to stainless steel and carbon steel, and titanium to carbon steel. Bend tests of bond integrity are described, and microstructures of the interfaces are presented. The amounts of brittle intermetallic phases formed at the interface are minimized by this cladding method.

Jan 1, 1980

The Bureau of Mines studied blast-produced ground vibration from surface mining to assess its damage and annoyance potential, and to determine safe levels and appropriate measurement techniques. Direct measurements were made of ground-vibration-produced structure responses and damage in 76 homes for 219 production blasts. These results were combined with damage data from nine other blasting studies, including the three analyzed previously for Bureau of Mines Bulletin 656. Save levels of ground vibration from blasting range from 0.5 to 2.0 in/sec peak particle velocity for residential-type structures. The damage threshold values are functions of the frequencies of the vibration transmitted into the residences and the types of construction. Particularly serious are the low-frequency vibrations that exist in soft foundation materials and/or result from long blast-to-residence distances. These vibrations produce not only structure resonances (4 to 12 Hz for whole structures and 10 to 25 Hz for mid walls) but also excessive levels of displacement and strain. Threshold damage was defined as the occurrence of cosmetic damage; that is, the most superficial interior cracking of the type that develops in all homes independent of blasting. Homes with plastered interior walls are more susceptible to blast-produced cracking then modern gypsum wallboard; the latter are adequately protected by a minimum particle velocity of approximately 0.75 in/ sec for frequencies below 40 Hz. Structure response amplification factors were measured; typical values were 1.5 for structures as a whole (racking) and 4 for midwalls, at their respective resonance frequencies. For blast vibrations above 40 Hz, all amplification factors for frame residential structures were less than unity. The human response and annoyance problem from ground vibration is aggravated by wall rattling, secondary noises, and the presence of airblast. Approximately 5 to 10 pct of the neighbors will judge peak particle velocity levels of 0.5 to 0.75 in/sec as "less than acceptable" (i.e., unacceptable) based on direct reactions to the vibration. Even lower levels cause psychological response problems, and thus social, economic, and public relations factors become critical for continued blasting.

Jan 1, 1980

By Virgil J. Stachura

The Bureau of Mines has investigated techniques and instrumentation that measure accurately the airblast overpressures from surface mine blasting. The results include equivalencies between broadband research instrumentation and commercially available impulse precision sound levels meters measuring: root-mean-square, peak, fast, slow, impulse, A and C weighting, C-weighted sound exposure level (CSEL), and "linear" (flat) response. These values were obtained from field measurements and broadband FM tape recordings of production blasts at area and contour coal mines, limestones quarries, and iron mines. Frequency response was determined for 14 commercial systems.

Jan 1, 1981

By Theodore Christos

The Bureau of Mines sponsored an investigation of the thermal oxidative degradation characteristics of certain solvents and hydraulic fluids used in underground mining operations. The following halogenated solvents were studied in view of their usefulness and their flame retardant property: tetrachloroethylene, C12C = CC12; 1, 1, 2-trichloroethane, CIH2CCHC12: and trichloroethylene, C12C = CHC1. The hydraulic fluids studied were representative of five groups approved by the Mine Safety and Health Administration for underground operation, namely: glycol-water solutions, mineral oil-water emulsions, synthetics other than phosphate esters, synthetic phosphate esters, and mixtures of phosphate esters with mineral oils and other ingredients. It was observed that the partially halogenated solvents present a greater potential toxic hazard than the fully halogenated materials, due not only to the easy production of hydrogen chloride but also to their ease of oxidation leading to the formation of phosgene and carbon monoxide. The pure phosphate esters exhibited the best thermal oxidative stability of the five groups of hydraulic fluids tested. A fluid containing phosphate esters mixed with mineral oils and other unidentified ingredients appeared to be the most hazardous On the basis that it produced very toxic acrolein and phosphine.

Jan 1, 1980

By S. R. Crane

One Bureau of Mines goal is to minimize the undesirable environmental impacts associated with industrial plants emitting waste gases containing S02. To help meet this goal, a regenerable flue gas desulfurization process was developed. This process, known as the citrate process, uses a buffered weak acid solution to absorb S02 from the waste gas. The absorbed S02 is reacted with H2S to precipitate elemental sulfur and regenerate the solution for recycle. The H2S feedstock for the process, if not otherwise available, may be produced by reacting two-thirds of the recovered elemental sulfur with natural gas and steam. Laboratory investigations and pilot plant operations were conducted by the Bureau to determine if H2S from the natural gas, sulfur, and steam reaction was suitable for the citrate process. The laboratory investigations, in which an H2S generator was integrated with other citrate process operations, provided a basis for design and operation of the pilot plant. The objective of the pilot plant was primarily to provide H2S for the citrate pro-cess pilot plant at the Bunker Hill Co. lead smelter in Kellogg, Idaho. The design capacity of the pilot plant was 0.4 to 1.25 tons of H2S per day. The operation demonstrated that (1) a 77-to 79-dry-volume-percent H2S product could be produced from pilot-plant product sulfur, natural gas, and steam; (2) the product R2S regenerated the SO2-loaded citrate solution; and (3) under certain conditions over 95 percent of the natural gas could be converted to H2S.

Jan 1, 1981