Search Documents

By Shuan-cheng Gu

Roof bed separation often occurred due to the deformation incoordination of surrounding rock following the excavation of mine roadway. Bed separation has effect on the bolts, and the estimation of the influence will directly affect the safety of support systems. In this paper, the hyperbolic function model to analyze the load transfer mechanism on the bolts was simplified as the exponential function form for easy calculation. An elastic-plastic analysis model of the bolt loading occurred by the bed separation was established. And the development low that the bed separation affected to the bolt loading was discussed. According to the parameters analysis of different separation values and locations, the influence law of the bolt loading caused by roof bed separation was summarized. Finally, the effects of bed separation were considered for the bolting design, it was able to provide a reference to the anchorage design of stratified rock.

Aug 1, 2013

By E. Vesely, A. Saxena

"SAG mill liners are designed for protecting the mill shell and providing lifting power for ore charge and grinding media. Due to the impacts from the charge and the grinding media, the liner experiences dimple, plastic deformation, strain hardening, fatigue, peening and final failure. Because of the collisional environment directly measuring such dynamical loads is extremely difficult if not impossible. In this study we tried to evaluate the liner failure risk by simulating the collisions of solid particles with mill liner using Discrete Element Method (DEM). DEM simulation has been proved to be a very useful tool in evaluation of granular flow and its impacts on the solid structure. But there are certain limits in DEM coherently, such as the number of solid elements, the computer runtime, etc. Here we first present the general feature of the particle-liner collision in terms of impact force and collision energy. Then the effects of parameter selection is discussed. Our simulations show the fatal collisional event of huge impact force is very rare and the collisional events of low impact is much more frequent. The fatal event may contribute most to the liner failure. The rarity of the fatal events may be missed in a short runtime simulation. This technical challenge combined with lacking of criterion to evaluate varying impact loads in fatigue problems may further complicate the evaluation. Should we use the largest impact force alone or we should use the more frequent events is an open question and requires more effort. In order to evaluate the quality of liner design, we proposed a relative comparison method. In the end we show the implication and application of this method in liner optimization by a work example. In particular, the effects of the charge level of grinding balls and their size on the operation performance is presented.INTRODUCTION Grinding is one of the most important and expensive steps of mineral processing. A variety of grinding mills such as rod mills, ball mills, semi-autogenous (SAG) mills and autogenous (AG) mills are being utilized for comminution of mineral ores (Gupta & Yan, 2016). Up to today, SAG mills and AG mills have been widely used to reduce operation costs and increase throughput. In an AG mill, a rotating drum throws larger rocks of ore in a cascading motion which causes impact breakage of larger rocks and compressive grinding of finer particles. Unlike AG mills, SAG mills use steel grinding balls to break ores of size quite small such that they cannot be easily broken in AG mill. SAG mill liners are designed for protecting the mill shell and providing lifting power for ore charge and grinding media. Due to the impacts from the charge and the grinding media, the liner experiences dimple, plastic deformation, strain hardening, fatigue, peening and final failure. Quality and performance of SAG mill liners play a fundamental role to enhance efficiency of grinding mills, because failure of liners is the major cause for unexpected breakdown (Banisi, Hadizadeh, Mahmoudabadi, & Eilkhany, 2006)."

Jan 1, 2019

By Douglas J. Harvey, Chi-Mou Ni

"This paper presents an analysis technique for the solidification of metal castings. This method, based on a modified finite difference scheme with an irregular mesh, is capable of dealing with the complex geometries of castings. The nonlinearities in material properties of specific heat and thermal conductivity, arising from the phase change during solidification, are accounted for in the step-by-step calculations. Two solidification problems are solved with this analysis technique and the calculated results compare satisfactorily with experimental data. IntroductionCasting process design engineers are often faced with the difficult problem of designing castings to be produced porosity-free. Since the solidification of metal is affected by many interacting variables such as the thermal conductivity, density, and specific heat of both the molten metal and the mold, it is easily seen why this is a difficult task.Typically, casting tooling design is an intuitive process which builds on past successful methods. After processing equipment is constructed, trial castings are made and examined for dimensions and integrity. Changes in the tooling are generally required to improve casting soundness or to reduce cycle time. In the permanent mold process, tooling is complex and difficult to alter after initial construction. The water-cooled steel molds are part of the complete automated system. Associated holding furnaces, pouring ladles, casting conveyers, and utility connections all make other than minor adjustments a costly and time consuming task. An analytical method for using the principles of heat transfer for predicting solidification patterns would be of great value in the permanent mold process by minimizing costly changes."

Jan 1, 1986

By Viktor Lishchuk, Olof Martinsson, Tobias E. Bauer, Elena Haller

Freely accessible and non-confidential real-life geological data sets from mineral deposits are desirable for the wide range of applications in research and education. However, publicly available statistical data are limited in their number and quality—they contain reduced information about geological, geophysical, geotechnical, chemical, mineralogical, and other relevant properties of deposits. This makes such data insufficient for scientific purposes. However, the amount of geological knowledge obtained for a variety of deposits in the past allows the construction of an idealized synthetic ore body model using analytical approach. Such a model could be used for education purposes and testing basic scientific theories, e.g., visualization of deposit structure; teaching sampling strategies; testing new algorithms for mine planning; or comparing geostatistical modeling methods. This paper presents an analytical approach to simulate volcanic massive sulfide (VMS) deposits and shows how synthetic deposit model can be constructed and further used for studying sampling with drilling and simulating folding and faulting.

Jan 14, 2021

By Randall M. Wheeler

Using Computer software to analyze and interpret blast vibration effects has never been so practical. Fully digital seismographs and powerful desktop and portable computers have led to the development of fast and easy to use analysis software. This workshop will focus on new Microsoft Windows-based blast vibration analysis programs developed by White Industrial Seismology, Inc. The Windows point and click graphical environment is ideal for developing full-featured and yet intuitive software.

Jan 1, 1994

By Gerald H. Luttrell

The determination of mass balances is the first step in analyzing the performance of processing circuits. Although conceptually very simple, the mathematics associated with mass balances can be cumbersome when conflicting data sets and/or complex circuits are evaluated. Fortunately, many of the spreadsheet programs available today include powerful search routines which can be adapted to solve common mass balance problems. To demonstrate these capabilities, a generalized mass balance program has been developed using the Microsoft Excel? spreadsheet. Compared to commercial programs, the spreadsheet format is user-friendly, more versatile and easier to customize. This paper reviews the mass balance problem and describes how spreadsheet tools can be used to reconcile conflicting data.

Jan 1, 1996

By Atmesh K. Sinha

Death and injury rates in mining have been the highest of any industry; the injury severity rates in mines have also been the highest. Tentative figures reveal that 1971 was the best year yet for the bituminous coal indus¬try with the lowest number of fatal accidents. Nevertheless, 177 men were killed at a frequency rate of 0.76 per million man hours. Coal mine accident statistics have been described at various times as unacceptable and intolerable and recently resulted in the enactment of massive legislation. The 1969 Coal Mine Health and Safety Act was passed by Congress "to improve the working conditions and practices in coal mines and to prevent accidents and occupational diseases originating in the coal mining industry." The prevention of accidents in coal mines is the statutory responsibility of mining engineers and the moral responsibility of all who have any part to play in mining coal. The questions to be answered by these men may well be - What are the reasons for the high accident rate? Are the mines as safe as they can be? Are our mines sufficiently manned to insure proper supervision of production cycles and safety requirements? Are our plans for safety committees, safety campaigns, and safety inspections sufficient? Are they producing the results intended? If not, how can these be reorganized to have a greater impact? What is the real cost of an accident? What are the immediate and long-term plans for further improvements? These questions are in no way exhaustive, and the answers are not easy. There are many aspects of mine safety, and any one of them can be the subject of a lengthy discussion. The aim of this paper, therefore, is to limit the analysis to documented fatal electrical accidents in mines so that meaningful conclusions for improvement in electrical accident-experience statistics can be made. In doing this, it is also the intention to emphasize areas of missing information and propose a few suggestions for better hazard analysis.

Jan 1, 1972

By W. B. Lambert

A common decision in openpit mining is to determine the extraction sequence of notional three-dimensional production blocks so as to maximize the net present value of the extracted orebody, while adhering to precedence and operational resource constraints. This openpit block sequencing (OPBS) problem is commonly formulated as an integer program, with binary variables representing if and when each block is extracted. In practical applications, the number of blocks can be large and the time horizon can be long; therefore, instances of this problem can be difficult to solve using the exact approach of optimization. The problem is even more challenging to solve when it includes explicit minimum operational resource constraints. Our maximum value feasible pit (MVFP) algorithm generates an initial integer feasible solution for OPBS problems, in which minimum operational resource constraints are strictly enforced. As an exact approach, we present a Tailored Lagrangian Relaxation (TLR), in which the selection of constraints to dualize is guided by information provided by the MVFP algorithm. We present results and graphics to demonstrate the utility of our techniques for instances containing up to 25,000 blocks and 10 time periods.

Jan 1, 2013

By Karoly (Charles) Kocsis, August Greth, Jon Fox

"It is the duty of the mine operator to ensure the mine environment is healthy and safe for the mine workers. For deep and hot underground mines, this requires maintaining adequate working temperatures by means of mitigating the heat load generated by strata, auto-compression, mining equipment, explosives, ground water and human metabolism. The heat load is best reduced by minimizing the amount of heat transferred to the mine air from these sources and through the use of efficient ventilation with effective cooling systems. The heat emitted by mining equipment and vehicles contributes a significant proportion to the combined heat load of an underground mine. This is especially a problem for diesel equipment due to the fact that besides heat, a large amount of water vapor is produced, which increases the humidity in the production workings. Diesel engines have proven advantageous in recent history due to their high power output and reliability. However, as mines continue to become more mechanized and deeper the climatic problems introduced by elevated heat generation will continue to rise. With that, the issue of heat generated by diesel equipment must be addressed.The economic alternative for diesel engine equipment fleets in underground mines is the electric engine. Technological advances in battery technology, increased mechanical output and improved reliability have made the electric engine significantly more competitive in comparison to diesel engines. Because electric engines do not utilize internal combustion, the heat produced by them is significantly less than the diesel engines. Battery-powered mining equipment likewise eliminate diesel particulate matter (DPM) produced by diesel engines. Utilizing battery electric equipment in underground mines provides many advantages, such as: (a) reduced heat load, (b) healthier and safer environment for the mine workers and (c) reduced mine operating costs due to lower ventilation requirements"

Jan 8, 2018

By M. R. Rosen

A technique is presented for simple characterization of the performance of flocculents in various mining applications. The method utilizes three key parameters obtained from raw settling data and combines them into a single athematical parameter called the desirability coefficient. The first two parameters are the timesrequired for the slurry-supernatant interface -to fall to two selected fractions of the starting height, and the third is the clarity of the supernatant liquid. The relative values of the three parameters may be assigned different weights in order to make them correspond with laboratory and field performance requirements of a particular industry. Provision is also made of an, internal comparison of test flocculant data with that of a control.

Jan 1, 1980

By Seth L. Pearlman

A major excavation support case history for the Eastern approach to the Third Harbor Tunnel (THT) in Boston, MA is described, which uses an anchored Soil Mixed Wall (SMW). Both general and project specific information is provided regarding the design and construction of SMW walls. In addition, conclusions are presented that discuss the suitability of this particular application and other possible variations.

Jan 1, 1993

By George Brien, O&apos

The history of the lighting of mine workings dates back to the early part of the 18th century, when small candles known as tallow dips, were used. These were set or held in a lump of wet clay. When looking for gas the flame of. the candle was reduced to a mere glimmer by surrounding the wick below the flame with clay. The candle was then very cautiously raised from the floor toward the roof, the observer screening the brighter portion of the flame with his hand and watching for the first appearance of the pale blue cap above the flame, even at that time, known to indicate the presence of gas. When this appeared the candle was lowered quietly and its flame extinguished before attempting to drive out the gas. A very common and dangerous practice adopted at that time was to get rid of the gas by firing it. This was done by a person selected for his nerve rather than for his caution. Dressed in a? suit of dampened sackcloth or leather, this man well termed a "fireman", would lie prone on the floor of the roadway and light the gas above him by raising his candle fastened to the end of a long stick. If he survived, which was not always the case, he would withdraw promptly to fresh air after the flame had passed over him.

Jan 1, 1924

By G. M. Bernard

The Andacollo gold mine is located near the small town of Andacollo, Chile (population 14,000) in the fourth region. It is approximately 35 miles by paved road from the coastal city of La Serena, and Santiago lies about 300 miles to the south (see map.) Site elevation varies between 3300 feet and 4200 feet. The climate at the site is moderate but arid, with an average annual rainfall of only five inches. Because there is little rain, and the temperature varies only a few degrees (57"F to 75°F); there are no freezing, solution dilution, or pad saturation problems. The climatic conditions are ideal for heap leaching.

Jan 1, 1996

Terramin Australia LimitedÆs Angas Lead and Zinc Mine operates in the unique and picturesque environment of Adelaide Hills, 60 km South East of the Adelaide city centre itself. The mine was granted approval for construction by the South Australian Government in April 2007 and the Process Plant was constructed and commissioned in July 2008. This paper outlines the background to the plant design and the approval process given the close proximity to the local town of Strathalbyn, with a major focus on the commissioning learnings from the Concentrator startup for future reference and a review of the operational performance of the Concentrator throughout the first year of successful production versus design and expectations.

Jan 1, 2009

By V Ser, R Crosbie

To date, Anglo American Research Laboratories (AARL) has carried out several projects, based on the techniques developed in AMIRA International LimitedÆs (the mineral industries research association) AMIRA P9 project, to develop models for several Anglo Base Metals flotation plants. Further detailed analysis of the data which was generated has realised additional benefits: the various hydrodynamic measurements were useful in comparing cell operating parameters to literature sources, while the laboratory batch tests give an indication of plant recovery potential. A detailed cell by cell mass balance, which is a critical feature of the modelling process, is in its own right a valuable diagnostic tool. Several examples of how this can be used to highlight potential improvement areas in the plants are presented. The added understanding gained from sampling each cell is clear and this is shown to more than compensate for any necessary modifications needed to allow sampling to take place. The model fitting process generates an ore floatability distribution, which is used in the JK SimFloat simulation package to assess the effect of possible changes to each of the circuits. An example of an actual circuit change as a result of this approach is presented. The current limitations of and the potential improvements to the modelling process are also briefly discussed. Future models will be extended to include enhanced size and mineralogical information where the basic models suggest this has potential to improve understanding.

Jan 1, 2005

By Max W. Ball

YOU have been kind enough to ask me to speak to you on "The War and Anglo-American Relations." A speaker always takes the liberty of putting his own interpretation on the scope of his subject. I am going to exercise that privilege, and try to look back over a generation of Anglo-American relationships and forward beyond the present war. I should like particularly to consider responsibilities as well as relationships. A more accurate caption for what I am going to say would be "Anglo-American Responsibilities.?? THE WAR WILL BE WON I am assuming that sooner or later we shall win this war. History and economics point to the same conclusion, that Germany has attempted the impossible and that the seeds of defeat are already sown. As to one ecof1:omic factor, I am already on public record as believing that Germany's oil supply is inadequate for the war she has launched. That opinion is unchanged. Aside from such tangible factors, moreover, I am convinced that the spirit of freedom is unquenchable, and that no combination of powers will be able to rout it from the British Commonwealth of Nations and the United States. Stronger even than this conviction is my faith in a God who will not suffer the defeat of man's aspiration to be master of his own soul. I am sure that all of you share that faith, and that we need not argue it. We can start with the assumption that the war will end in victory. The subject we are to consider, then, is the relationship of the English-thinking peoples during the conflict, and their joint responsibilities in the difficult days that will follow it. A CANADIAN-AMERICAN No talk on such a subject is worth listening to unless the audience knows the background and fundamental beliefs of the speaker. No human statement stands alone; behind and beside and within it are the ideals and the bias of the man who makes it. Because I am a stranger to most of you, I am constrained to talk about myself before I talk about more important matters. The review may be profitable, not because of the subject, but because it may illustrate the evolution of an attitude toward England.

Jan 1, 1941

By J. R. Sturgul

Computer simulation models of working mines can be of great benefit to the mining engineer. Such models have been used in mine planning (how many trucks/shovels to have, when to add new equipment, etc.), mine design (should a dispatch system be purchased, where is the optimum location for mine equipment, etc.). A simulation model can be thought of as a dynamic representation of the mine and can easily be changed to reflect a wide variety of different situation. Often a major problem for the engineer is how to present the results of the simulation study. Using PROOF(R) animation it is now possible to interface the results of the simulation and project them onto a computer screen in cartoon fashion.

Jan 1, 1993

By Steve Linehan, John Toedter, Kelly Williams, Mark Herman, Laura Connor, Catherine E. Johnson

Minimum safe distance (MSD) calculations are used widely in military applications to determine safe standoff distances for breaching personnel. Accurate safe distances and an understanding of blast wave propagation are critical to preventing traumatic brain injury. These calculations are often based on spherical charges in open air. However, applications including explosive breaching use planar charges rather than spherical. Previous studies analyzed the shock propagation of a square planar charge of sheet explosive and concluded the anisotropic pattern conflicted with the Kingery Bulmash (KB) and MSD spherical models. It has been determined that these predictions do not adequately predict the realistic pressures in all directions and the trend has shown to be consistent across multiple charge geometries. In this series of experiments, pressures were collected from reference spheres and rectangular geometries of detonating cord and sheet explosive commonly used in breaching and improvised demolition for this comparison. This common configuration showed pressure differences at varying angles to the charge with the highest pressures measured at the 90° position perpendicular to the “door” to be breached. Lower pressures were found at the 0° and 15° positions where the breachers would normally be standing. The reflected shock from a surface such as a door was incorporated in a semi-confined situation and added to the shock observed by the breachers. Urban environments include many surrounding structures for these reflections to occur and further testing is necessary in such an environment to determine the full-scale impact. These findings may be useful to develop improved MSD calculations for breaching applications based on charge geometry, orientation to the blast, and nearby structures.

Feb 6, 2023

By Harsh Deep Chopra, Jason N. Armstrong, Susan Z. Hua

"Existence of anisotropic Curie temperature materials [E. R. Callen, Phys. Rev. 124, 1373 (1961); J. Appl. Phys. 32 S221 (1961)] is a longstanding prediction - materials that become paramagnetic at a lower temperature along certain crystal directions while remaining magnetically ordered in other directions up to a higher temperature. Validating Callen's theory, we show that all directions within the basal plane of monoclinic F e1Ss (pyrrhotite) single crystal remain ordered up to 603 K while the c-axis becomes paramagnetic at 225 K. Results prompt a re-evaluation of existing magnetic materials with a focus on magnetic characteristics along different crystal orientations above instead of below the ordering temperatures. Theoretical guidelines for identifying new materials with large anisotropy of Curie temperature are also given, and analysis protocol to characterize them in a self-consistent manner is discussed. Materials with such a large directional dependence of Curie temperature open the possibility for uniquely new devices and phenomena, including energy storage and spintronics devices.IntroductionThis paper is an overview of our recently published work on anisotropic Curie temperature materials [l]. As a background, ferromagnetic and ferrimagnetic materials are characterized by a critical temperature below which magnetic interactions prevail over thermal agitation, leading to the appearance of a spontaneous magnetization. Above this critical point, called the Curie temperature, thermal energy eventually overcomes magnetic interactions and the material becomes paramagnetic.It is less well known that the Curie temperature varies with the orientation of the crystal. In ordinary ferromagnets this orientation dependence of Curie temperature is negligible because of the vanishingly small ratio of anisotropy to exchange energy, i.e., the spherical or isotropic exchange term dominates. Thus Curie temperature in ordinary ferromagnets appears to be an isotropic property, and assigning it a single characteristic ordering temperature suffices. However, a 'small' difference is not equivalent to being the 'same', and under appropriate set of conditions the anisotropy of Curie temperature is predicted to become appreciable, as discussed in the following.In formulating the theory of 'anisotropic magnetization' [2, 3] E. R. Callen and H. B. Callen first discussed the ""interesting possibility"" of anisotropic Curie temperature [2] or ACT; Callen and Callen noted that it was W. J. Carr, Jr. who initially raised this question, and they discussed it in detail at the Conference on Magnetism and Magnetic Materials (NY, November 1960), see footnote on page 320 of Ref. [2]. Soon thereafter, E. R. Callen developed the theory underlying the anisotropy of Curie temperature and conditions conducive to its observation [4, 5]."

Jan 1, 2013

By T. W. Wong, M. A. Whitney, A. Hadadzadeh

Uniaxial compression tests were performed on cylindrical specimens, 10mm in diameter and 15mm in height, machined from an extruded AZ31B magnesium billet. The tests were conducted under isothermal conditions to a true strain of 0.5. The study compares macroscopic flow anisotropy between the extruded (ED) and transverse (TD) directions in the temperature range of 300°C to 500°C, and strain rate range of 0.001s-1 to 1s-1. Compression of ED specimens at low strain rate (0.001s-1) exhibited axisymmetric flow, and no significant differences were observed between geometries of specimens deformed above 350°C under the same strain rate. Deformation of TD specimens at low temperature and/or low strain rate resulted in elliptical cross-sections, with the anisotropy of flow being less significant at higher temperatures. Other studies performed using rolled plates have proposed that pyramidal slip and cross-slip at higher temperature eliminate the effects of initial texture, while the dominance of prismatic slip at lower temperatures will result in anisotropic flow. It is believed that the initial fiber texture common among extruded HCP-structured materials plays a role in the anisotropic deformation behaviour observed in the extruded specimens

Jan 1, 2015