Search Documents

By O. W. Bilharz

INTRODUCTION ACID mine-water drainage is a serious problem with many mines in the Tri-State zinc and lead mining district. Particularly is this true when large volumes must be considered in unwatering old mines that have refilled with water which has dissolved the products of oxidation and has become chalybeate in character. The experiences discussed in this paper have to do specifically with the unwatering of a comparatively small area west of the town of Baxter Springs, Kans., where the pumping job was complicated by water of this type and where the extremely high sulphate content particularly effected that phase of mine drainage having to do with stream pollution. LOCATION, GEOLOGY AND HISTORY The Baxter Springs area of the Tri-State mining field is situated just west of the town of Baxter Springs and is a northeasterly extension of the main mineralized zones of the Oklahoma part of the district (Fig I). The mining area is traversed with well defined shear zones which provide easy circulation of ground waters and the ore bodies are found along these shear zones as localized enrichments wherever the structural conditions are favorable (Fig 2). The ore-bearing strata is Mississippian with an overlain capping of shale of Pennsylvanian age. This shale strata carries much pyrite and marcasite at its base and undoubtedly was a contributing factor to the subsequent high iron content of the water. The area originally contained a sulphide water which discharged as an artesian flow in springs within the town and gave Baxter Springs its name. These springs were famed for many years for their mineral water. This original sulphide water was first removed about 1917 and active mining was carried on west of the town during subsequent high metal price periods. Many small mines were opened, with each localized enrichment becoming a separate mine. During the depression mining ceased and all mines in the west Baxter area were allowed to flood. No serious effort was made to again unwater until higher prices caused from the demand for metal for World War II once more focused attention on this part of the field. ORIGINAL MINING RESULTS IN OXIDATION As plans for unwatering progressed, it soon developed that the mine-water pools had become strongly acid in character and carried large amounts of sulphates in solution. This occurred in the following way. When the original sulphide water was removed, shafts sunk, and mining carried on over a number of years, ferrous sulphate was formed by the spontaneous oxidation of the pyrite beds in contact with air admitted through churn-drill holes and mine openings. These products of oxidation can be seen today in the old mines of the district as crusts of crystalline sulphates

Jan 1, 1947

By Seppo] [Kreula

Outokumpu Oy has acquired considerable experience with on-stream X-ray fluorescence analyzers and with computer control of flotation processes over several years. It became evident at the outset of this work that a reliable and accurate on-stream analyzer was more than a collection of different pieces of hardware linked together. Extensive work was done to develop an integral analyzer system, beginning with process samples through the spectrometer to report typewriters, recorders and the control computer. To date, over ten Courier-300 analyzer systems based on this development have been installed world-wide, several of which provide the key information for successful computer control systems. Computer control of flotation processes has been under development at the Pyhäsalmi concentrator since 1968. Two different control strategies have been implemented. The copper flotation is controlled by means of a mathematical model and economic criteria, whereas the "evolutionary operation principle" is applied to the zinc flotation. The computer control system installed at' the Vuonos-mine has been developed according to the same guidelines. In order to consolidate this wide experience, a flotation computer control system, Proscon-100, was developed by Outokumpu Oy, and the first system was installed at Kotalahti in 1972. In addition to the technological experience, enough information has also been gathered to illustrate the economical, benefits accruing through the use of these advanced tools of automation.

Jan 1, 1973

By James J. Bean

Although determining and controlling specific gravity of operating medium in a heavy-media plant manually presents no problem, there are advantages to automatic recording and control. The two installations discussed employ the usual method of measurement. Pneumatic control with band control and reset features is used to regulate dilution water and hence specific gravity. Difficulties have been mechanical in nature and associated with obtaining a proper I sample and maintaining tight air connections in bubble-tube piping:

Jan 1, 1950

By Karl Gunnar Holter, Frank Clement

"INTRODUCTION Typically waterproofing of conventionally excavated tunnels has been done by installing pre-fabricated sheet membranes between the primary temporary support lining and the secondary permanent inner lining. The membrane acts as a separation or sliding layer between the linings, which is often desirable. The geotextile installed behind the sheet membrane provides the required drainage and protection of the system. The design of the tunnel lining is strongly influenced and limited by the use of waterproofing sheet membranes. Since primary and secondary linings are separated from each other, forming a double-shell lining system. In that case the secondary lining must be designed for all permanent loads, although the sprayed concrete primary lining continues resists ground and water loads for a long time after construction. Significant progress has been made in sprayed concrete technology over the last two decades, with advanced admixtures, as well as the improved application technology using spraying robots. The development of new admixtures like superplasticizers based on poly-carboxylates, alkali free accelerators and silica fume, enables designers to use permanent sprayed concrete linings (SCL) increasingly for long-term service life. When designed and applied correctly, sprayed concrete can be considered as permanent. The use of spray applied membranes has seen increased use over the last decade in some countries, and demonstrated functionality and cost-effectiveness in several situations. This paper describes the use of the sprayed waterproofing membrane MasterSeal 345, an EVA polymer based product, and the practical experiences from several projects. SPRAY APPLIED WATERPROOFING MEMBRANES The sprayed waterproofing membrane is polymer based and has been especially developed for underground structures. The membrane is applied between primary and secondary concrete linings and develops high bond strength on both sides to the concrete (doubled-bonded)."

Jan 1, 2016

By Kent Zehr

Suncor Energy Inc. is an integrated producer and refiner of oil and gas headquartered in Calgary, Alberta. The bulk of revenue comes from the Oil Sands Group (OSG) operating in the McMurray formation of the Athabasca Oil Sands. Located some 25 kilometers north of Fort McMurray, Suncor OSG began life in 1967 as Great Canadian Oil Sands, the first operator to successfully enter commercial production of synthetic crude oils from the area. For most of the last decade, dramatic growth has been the standard mode of operation for Suncor OSG. Production of synthetic crude first reached 100,000 barrels per day in 1997 and less than five years later is averaging in excess of 200,000 barrels per day. Within this dynamic organization, Suncor Extraction is the business unit that processes run-of-mine ore into clean diluted bitumen for Upgrader feedstock. Extraction also delivers and places the barren sand and process affected water into tailings storage in one of several ponds from which water is recycled to support the various processes. For reference purposes, Extraction on a typical day currently receives more than 400,000 metric tons of oilsand ore, which is all processed to water based slurry for separation in one of two extraction plants. Separated tailings are disposed of as a slurry and the cleaned bitumen froth is diluted with naphtha and sent to tankage for storage until required by the Upgrading Unit. As a consequence, on a typical day Suncor Extraction pumps more than 1,000,000 tonnes of aggressive slurry into and out of the two extraction plants.

May 1, 2003

By C. H. Zhou

Cryogenic grinding of Printed Circuit Board will bring less pollution, reduce energy costs, smaller particles, regular particle size, efficient process, separation various materials due to different fracture toughness. Systemic studies of recycling discarded Printed Circuit Board (PCB) by low-temperature modification and cryogenic grinding have been made in this paper. Firstly test mechanical property of PCB at different low-temperature, including impact strength, flexural strength, and shear strength. Do experiment on the power consumption of different cooling temperature, The results show that the average power consumption is lower between -30? to -60? and the average power is decrease in evidence at -30?. Use ZKB type double roll shear crusher to crush PCB to 20mm×20mm particle size, in a temperature range of -10 ~ -30? Used R type mill to grind sample to minus 3mm under different working condition, the average power consumption is decrease in evidence from -10 ? to -30 ?, power consumption is the lest at rotational speed is 1180rpm.

Jan 1, 2014

By E. Hasanbas

Vibrating screens and crushers are the workhorses of material sizing. Unfortunately their natural frequency is often in the range of typical supporting structures, thereby making installations prone to vibration problems. Much of the available literature regarding the support of vibrating screens is fairly confusing and outdated. This paper presents the results of utilizing accelerometers and finite element software in the analysis and design of supports for vibrating equipment. It contains data from field studies of vibrating screen and crusher installations, design of new and repair of existing supporting structures, and the correlation between field data and finite element time history analyses. Finally, the paper summarizes a method for analyzing and designing structures subjected to vibratory loads and predicting their behavior.

Feb 23, 2014

By Chenyang Zhang, Zhigang Yin, Wei Sun, Jingxiang Zou, Jianyong He, Yuehua Hu, Zhijie Xu

"In this work, a novel compound 4-Amino-5-mercapto-1,2,4-triazole was first synthesized and its selective adsorption mechanism on the surface of chalcopyrite was comprehensively investigated using UV-vis spectra, zeta potential, Fourier Transform Infrared Spectroscopy(FTIR), X-ray Photoelectron Spectrscpy Measurements(XPS), and Time of Flight Secondary Ion Mass Spectrometry (ToF-SIMS) and first principle calculations. The experimental and computational results consistently demonstrated that AMT would chemisorb onto the chalcopyrite surface by the formation of a five-membered chelate ring. The first principle periodic calculations further indicated that AMT would prefer to adsorb onto Cu rather than Fe due to the more negative adsorption energy of AMT on Cu on the chalcopyrite (001) surface, which was further confirmed by the coordination bonding energies of AMT-Cu and AMT-Fe based on the simplified cluster models at a higher accuracy level (UB3LYP/Def2TZVP). The bench scale results indicated that the selective index improved significantly when using AMT as a potential chalcopyrite depressant in Cu-Mo flotation separation.INTRODUCTIONFroth flotation is one of the most important processes to separate valuable minerals from gangue by taking advantage of differences in the physical chemistry of their surface properties(Laitinen et al., 2014), particularly in their surface hydrophobicity. Hydrophobicity differences between valuable and gangue minerals could be regulated by adding different chemical additives (surfactants)(Kor, Korczyk, Addai-Mensah, Krasowska, & Beattie, 2014), such as collector and depressant. It could be conducted economically to selectively separate and enrich the complicated and/or poor ores, by adopting appropriate surfactants. For example, the beneficiation of molybdenite usually relies on a two-stage process to realize flotation separation of molybdenite from other unwanted sulphide ores(Wie & Fuerstenau, 1974). In the first step, a bulk molybdenite concentrate is produced by utilizing kerosene/ diesel oil and pine oil/alcohols as collector and frother, respectively. Second, sodium hydrosulphide, sodium cyanide, ammonium sulphide, or Nokes reagent are adopted as depressants in the separation stage. However, these depressants are usually toxicant and cannot meet the requirements of environmental protection. A large number of efforts have been taken to develop alternative environmentally-friendly depressants (Ansari & Pawlik, 2007; J. H. Chen, Lan, & Liao, 2013; Li et al., 2015; Yin, Sun, Hu, Zhai, & Guan, 2017; Yin, Sun, Hu, Zhang, Guan, Liu, et al., 2017; Yin et al., 2016). Although some novel and environmental-friendly depressants have been reported to achieve good performance in Cu-Mo flotation separation at a laboratory scale, there are still some challenging problems, including toxicity, high price or poor performance in practice, which severely limit their practical applications in Cu-Mo flotation separation on a commercial scale."

Jan 1, 2018

By Godfred Amponsah, Mehrdad Razavi

Slope failures very commonly occur during a long period of heavy rainfall and groundwater rise. The failures pose a substantial risk to people, infrastructure, and equipment downslope. In the recent past, the mining industry has faced an increase in tailings dam failure due to several reasons including pore pressure increases in the dams. Many failures have been observed to occur during times of water level fluctuations but the critical factors that influence the initiation of slope failures still need to be adequately clarified. To investigate these factors, laboratory experiments were conducted on model sandy slopes to determine pore pressure-induced slope failure initiation. This study also presents a method to examine water seepage through soil slopes using an ultraviolet (UV) dye and a UV flashlight. The small-scale model test simulation demonstrated failures induced by either water percolation from the upslope tank at a constant level or by raising the water level at intervals. A bottom chamber fully filled with water to replicate groundwater rise was also simulated. The soil slope was monitored at every stage to study the deformations and behavior until failure occurred. Results gathered from the controlled laboratory conditions were useful for the verification of the numerical modeling method created in the computer program Slide. The analysis showed that slope failure always occurred when the toe was fully saturated. High pore pressures and seepage forces reduce the shear force at the toe to almost zero causing it to slide. A comparison of slope height to water level also indicated an average of 96% water level to cause a failure. At this point, the soil slope is fully saturated and has no matric suction. The findings in this study show that, by monitoring the moisture content of slopes, failures can be predicted.

Feb 1, 2024

By Nikolaos Petropoulos, Changping Yi, Daniel Johansson, Håkan Schunnesson

The effect of jointing on fragmentation by blasting was investigated experimentally and numerically. Firstly the experimental results were presented. Then the numerical modelling based on the experiments was performed. The same conclusions can be obtained based on both experiments and numerical modelling.

Feb 1, 2020

By Frank J. Tolonen

BENEFICIATION of iron-bearing formations is one of the major problems of research at the Michigan College of Mining arid Technology. Funds for this purpose hate been supplied by the State of Michigan supplemented by contributions of labor and some supplies from the Federal Government during the depression. The iron-mining companies have cooperated in securing samples and have also furnished much valuable information relative to the various formations.

Jan 1, 1937

By R. J. Sweigard

Stabilization of slopes on abandoned mine land (AML) invariably involves some channelization to control surface drainage. Typically, these channels are lined with riprap or gabions, depending on gradient and expected flow rate. The conventional treatments pose a problem since they require frequent maintenance and replacement at times. Soil bioengineering presents an alternative to the conventional measures. In soil bioengineering, living woody plant material forms the main structural component in systems designed to prevent shallow mass slope failures, surface erosion, and channel bank erosion. An experimental application of soil bioengineering techniques was designed and implemented at an AML site in eastern Kentucky. The design consisted of live fascines and live stakes using willow branches installed with coir geotextile. Channel gradient, length, and cross-section were considered in the design.

Jan 1, 1998

By Y. Zedan

In this study, the statistical design of experiments (DOE) was applied to study and regulate the properties of near-eutectic Al-11%Si alloys. Develop regression equations for such response variables as hardness, yield stress, ultimate tensile stress, percent elongation, total cutting force, cutting power, and tool life together with other factors which, include the percentage composition of the alloying elements, and the requisite modification (Sr) level. These equations may be analyzed quantitatively to acquire an understating of the effects which the main variables and their interactions may have on the mechanical behaviour and the machinability of the alloy under investigation. The results reveal that increasing the levels of Cu and Fe content results in an increase in hardness, yield stress, and ultimate tensile strength in both modified and non-modified alloys. On the other hand, both Cu and Fe appear to affect the percentage elongation adversely, whereas the Sr-level has a positive effect on this parameter. It was found that Sr-levels have the most significant effect on the cutting forces and cutting power followed by the content in Fe and Cu. The results also reveal that the interaction coefficients of these variables have a significant effect on tool life compared to the main independent variables. This fact may be attributed to the formation of complex insoluble phases between Cu, Fe, Si, and Al as investigated using Scanning Electron Microscopy (SEM) attached to an EDX analysis system. The accuracy of the regression equations in predicting the expected properties has been verified by carrying out random experiments in the range of variation of these variables.

Jan 1, 2011

By J. A. Bakken

Thermal plasmas are interesting for a wide range of metallurgical and chemical processing applications. The 300 kW experimental reactor PRESS, which has been in use since 1987, is operated in the transferred arc mode with three or one plasma torches . Tests include remelting of silicon fines and production of ultrafine silica. Work on a novel three stage process for production of silicon metal is under way. A 1:1 model of the plasma reactor is used to measure the wall heat flux distribution calorimetrically. The cold walls of this model are divided into several water-cooled sections. The same plasma torches as in the real hot-wall reactor are used. In parallel to the experiments and calorimetric measurements theoretical work is done on numerical modelling of one and three transferred arcs. A modified version of the flow simulation program FLUENT from Creare Ltd. is used.

Jan 1, 1991

By R. A. Campbell

The electric smelting of five lowgrade Canadian manganese ores has been investigated at the Mines Branch, Department of Mines and Technical Surveys, Ottawa. Ferromanganese, silkomanganese, and spiegeleisen were produced 1by special smelting processes from these ores since the latter were too low grade to be treated by conventional smelting methods. In one case the results were considered to be sufficiently promising to justify the construction of a pilot plant, by the Company concerned, for the further development of the process.

Jan 1, 1956

By Jeffery L. Kohler

The research and development of a pattern recognition system which can predict incipient failures and safety hazards in the mine power network is described. An examination of mine electrical safety hazards revealed they are often related to the electrical equipment down-time experienced on mine sections. Based on this, a method is proposed that can improve both production and safety, without compromising either. Equipment failure modes are examined to illustrate how the ultimate failure can be predicted for enough in advance to allow a convenient and safe repair, followed by a discussion of actual monitoring system performance. Finally, the paper is concluded by projections of the system's utility to industry.

Jan 1, 1977

By Patrick M. Eduafo, Brajendra Mishra, Mark L. Strauss

Direct acid leaching of rare earth metals (REMs) from waste lamp phosphors is non-selective, leading to co-dissolution of impurities mainly calcium, phosphorus, silicon, iron and zinc. Calcining the phosphor powder at different temperatures followed by leaching with HCl isn’t efficient for the extraction of all the chief rare earths especially cerium (Ce), lanthanum (La) and terbium (Tb). Therefore, multi-stage leaching operations are required for the separation of the REMs in phosphor dust. This paper will outline a new process for extracting Ce, La, Tb, Eu and Y from waste fluorescent lamps using a three-stage leaching and separation process. A flowsheet has been developed which shows this process is selective and efficient.

Jan 1, 2015

By Kenneth Gavin, Weichao Li, Paul Doherty

"The lateral load capacity is one of the most important issues to be considered in designing piles to resist berthing loads, ship impact forces and for monopiles used in the offshore wind sector. A number of semi-empirical design approaches are available to calculate the ultimate soil resistance and assumed soil reaction profile along the piles’ embedded depth. In order to investigate the response of monopiles to lateral loading, a series of field experiments were conducted on instrumented steel pipe piles. Two lateral loading tests were performed on model piles with a diameter, D, of 340 mm and embedded depth, Lem, of 2.2 m, giving a Lem/D ratio similar to those adopted in the offshore wind sector. The piles were driven into dense sand at the University College Dublin geotechnical test bed site in Ireland. 10 pairs of strain gauges were installed on each model pile along the embedded depth at 10 levels to capture the load transfer and bending moment within the piles. The deflection and rotation at the model pile head were measured by Linear Variable Differential Transformer (LVDT) and inclinometers. The tests results were used to perform a detailed evaluation of current design methods. In the final section, discussion on the determination of the ultimate lateral load capacity for monopile design was conducted. IntroductionA pile’s lateral load capacity is determined, for design purposes, by two conditions: 1) the ultimate lateral load, Fu, divided by an appropriate safety factor; and 2) the load according to the maximum lateral deflection that the support structures can sustain. In view of the first condition, design methods to calculate the ultimate load were developed for piles used in the offshore oil and gas sectors, which tend to be much more slender than monopiles used in the wind industry. The purpose of this study was to investigate whether these design methods provide reasonable estimates of ultimate capacity, for short rigid monopiles.The methods to determine the ultimate lateral load generally follow three steps: 1) determine the ultimate soil resistance, Pu, along the pile embedded depth; 2) adopt the most appropriate soil reaction profile, Pz, along the piles embedded depth when the pile subjected to the ultimate lateral load condition (four of the most popular ones are depicted in Figure. 1); and 3) ensure equilibrium of lateral forces (see Equation 1, symbols are listed at the end of the paper) acting on the pile and bending moments (see Equation 2) about a point in pile is employed to determine the ultimate lateral load."

Jan 1, 2015

By C. Lupi

The electrorefining of primary copper is a well known technology: in this work copper scrap was directly processed in the same way. he copper and copper alloy scrap was previously pressed by means of a 20 tons apparatus in order to avoid pyrometallurgical operations. The samples obtained in this manner showed a good compactness so that they were used as anodes in the electrorefining tests. The tests were carried out on anodes made by copper scrap, copper alloy scrap and a mixture of the two. The electrorefining tests were performed at both 303 and 333 K, in a perspex cell having a volume of 500 ml using a current density of 250 A/m2. The cathode used was always a sheet of pure copper and the electrolyte composition was 40-50 g/l Cu as CuS04 and 150-200 g/l H2SO4. Current efficiency in the range of 92-97% and specific energy consumption ranging from 0.14- 0.20 kWg of copper were reached in all the tests. The refined copper deposits were analyzed by AAS to verify their purity and observed by SEM to highlight their morphology.

Jan 1, 1998

By G. Laird, N. B. Gray, N. Lawson

"Photographic, video, laser, hot film and conductivity methods are used in the experimental study of gas-liquid flows. A discussion of their capabilities and limitations are given in this paper illustrating the wide range of phenomena that can be studied. Most of these methods are limited to physical models at room temperature with transparent fluids, although they can be extended for use with opaque and hot fluids. A number of these techniques have been used by the GKW CRC in studies on industrial plants and their usage is increasing although a number of technical difficulties still need to be overcome. An in-depth discussion of the laser doppler anemometry (LDA) and particle image velocimetry (PIV) methods is given with experimental results on the flow field of an air plume in water based on advanced development of the techniques and studies carried out at the GKW CRC. The LDA method provides high resolution data on the velocity profiles, while the PIV method provides an overall view of the complex flow structure occurring at the gas-liquid regions. These two methods complement each other in providing experimental data for validating numerical models and exploring the complexities of multi phase flows.IntroductionThe injection of gases into melts is an important operation in the metallurgical industry. It is used in converters, anode furnaces, blast furnaces, ladles, bath smelters, zinc fumers and many other smelting processes. In many of these processes, the gas is injected into a molten bath resulting in the formation of bubbles that promote reaction, mixing, alloying and heat transfer. The study of gas-liquid systems presents enormous challenges to the researcher due to the complexity of the mathematical and physical modelling which require innovative numerical and experimental skills."

Jan 1, 1996