Search Documents

By M. P. Hoffman

The U.S. Bureau of Mines is developing a roof bolter with a computer-controlled drill head that will increase the safety of roof bolting in underground coal mines by allowing miners to be relocated to a safe area. To ensure secure anchorage, acceleration and strain data are broadcast from an instrumented drill steel to a data acquisition system. These data are analyzed, correlated, and transformed to pro-vide information about roof strata, then are sent to a supervisory computer executing National Institute of Standards and Technology's real-time control software. The supervisory computer sends setpoint commands to proportional-integral-derivative control loops to control drill thrust, position, revolutions per minute, and torque.

Jan 1, 1994

By D. C. Martin

Construction of the Cerro Colorado on-off leach pad in northern Chile required placement of approximately 3,000,000m3 of fill over a P1an area of approximately 600,000m in irregular terrain with relief of up to 40m. Earthwork construction was completed in approximately six months using mine waste which was placed in 4 to 6m lifts using mine haul trucks. The lift thickness was reduced and the compactive effort increased in the upper 10m to enable development of a mat and additional resistance to possible differential settlements under dynamic (earthquake) conditions. A single 80 mil (2mm) HOPE liner was used below the leach pads and this was protected from the loading and unloading equipment using an engineered liner system consisting of screened sand, gravel and silt from local sources as the bedding and cover layers, and a heel of screened gravel and primary crushed low grade ore. Settlement monitoring, field testing and subsequent assessments of liner performance have indicated an adequate design was achieved and the project proceeded with considerable savings in time and construction costs.

Jan 1, 1995

By M. R. Lastra

Island Copper Mine began gold recovery Tom molybdenum sulfide concentrates in April, 1985. Plant design capacity is 20 tons of molybdenum concentrate per day. The molybdenum concentrate is produced in a conventional copper/molybdenum flotation circuit by selective copper depression. After thickening, the molybdenum concentrate is leached with cyanide solution in a series of five leaching tanks. The leached concentrate is then filtered and soluble gold values recovered on activated carbon with a six column adsorption circuit. The gold leach extraction is approximately 80 percent with a gold adsorption on activated carbon of 97 percent.

Jan 1, 1986

By L. C. Raymond

Good afternoon. I have entitled my talk "Investment for Progress," implying thereby a spark of friendly competition by private enterprise with such government-inspired foreign aid and investment programs as the Alliance for Progress. While the subject of foreign investment is hardly a new one, the perpetual flux of the political and economic surface of this earth we inhabit makes it forever timely and forever interesting. Especially do tremendous opportunities for international investment constantly present themselves to the mineral industry, and just as often must the industry approach these opportunities with a great deal of investigation and caution. This is not to say that the mineral industry--no less than any other industry--should be unenthusiastic about the foreign scene, but like everyone who proposes to put his money where his hope is, it should consider all the factors and weigh the possible disappointments as well as the rewards.

Jan 1, 1964

By A. Torrance, M. G. Seo

Velocity of detonation (VOD) is an important variable when evaluating the performance of mine blasts. Typically, for a VOD measurement, individual probes have to be loaded into each blast hole that requires a measurement, which increases the loading time and is not representative of the whole blast. Experimental studies of electromagnetic pulse (EMP) from the detonation of explosive charges show that electric and magnetic field signals are observed when chemical explosions occur in the air, at the ground surface, and in the underground. EMP has the potential to evaluate VOD of the whole blast without impeding the loading process. Due to a variety of physical causes which make the electromagnetic effects complex, measuring EMP of the detonation of explosive charges has not been fully studied yet. Five different antennae were tested with explosives, which are commonly used in mining industry. Among the five antennae, aluminum and copper tape, and wire were successful to detect the EMP. INTRODUCTION The measurement of the velocity of detonation (VOD) helps in evaluating and comparing relative performance of explosives in mine blasts. A VOD of an explosive is usually predicted by empirical mathematical equations or measured in-hole by VOD meters. However, conventional methods to measure a VOD have constraints: only a limited number of holes can be measured because cost of consumables for such systems is very high, and systems only allow a certain number of holes to be measured. The measurement cables have to be placed into the holes prior to loading with explosives which means that preparing to take the measurement is time consuming and has to be well coordinated with the mine. In order to evaluate VOD for a whole blast, there is a possibility of using electromagnetic pulse (EMP) from the detonation of the explosives. As there are many parameters that affect the generated EMP from explosive charges, measuring EMP of the detonation of explosive charges has not been fully studied yet. Most studies conducted relate to military related explosives, not the ones frequently used in mining industry. This research has been performed to have a better understanding of EMP from the types of explosives which are commonly used in the mining industry. To discover a way to detect EMP efficiently, five different types of antennae have been studied in the air and in the underground blasting conditions: coil, monopole rod, log periodic, wire, and aluminum and copper tape. LITERATURE REVIEW Conventional methods of measuring VOD Over the years, demands for more accurate theoretical predictions and physical measurements of the effects of the explosives have increased. Especially when both demand and commodity price decline, mining companies are keen to understand the effectiveness of explosives since it has a direct relationship with fragmentation, which influences their production rate. Since the 1940s, various methods have been devised to determine VOD of explosives.

Jan 1, 2019

By W. B. Lambert

A common decision in openpit mining is to determine the extraction sequence of notional three-dimensional production blocks so as to maximize the net present value of the extracted orebody, while adhering to precedence and operational resource constraints. This openpit block sequencing (OPBS) problem is commonly formulated as an integer program, with binary variables representing if and when each block is extracted. In practical applications, the number of blocks can be large and the time horizon can be long; therefore, instances of this problem can be difficult to solve using the exact approach of optimization. The problem is even more challenging to solve when it includes explicit minimum operational resource constraints. Our maximum value feasible pit (MVFP) algorithm generates an initial integer feasible solution for OPBS problems, in which minimum operational resource constraints are strictly enforced. As an exact approach, we present a Tailored Lagrangian Relaxation (TLR), in which the selection of constraints to dualize is guided by information provided by the MVFP algorithm. We present results and graphics to demonstrate the utility of our techniques for instances containing up to 25,000 blocks and 10 time periods.

Jan 1, 2013

By Neal P. Cochran

It is always a pleasure for me to address a group of mining engineers. I am doubly grateful when I am allotted sufficient time to describe the total Office of Coal Research program. My remarks are directed to our total program but I trust you will all understand my emphasis of the utilization aspect of our activities since that is my portion of the program. From its inception, the Office of Coal Research has sought out creative ideas for improving our national use of coal by developing new uses, improved mining procedures, lower costs, and appropriate studies with respect to the resource itself. Quite early in the game, our Economics and Marketing Division contracted for studies with respect to New England export market, Western coal, and similar items. Our Mining and Preparation Division has successfully developed a packaged coal-fired boiler and has partially developed a packaged fluid-bed type boiler as well. Our Mining and Preparation Division is working in such diverse fields as treatment of sewage with coal and the separation of coal into distinct-petrographic constituents so that all fractions of the coal can be put to the best possible use. We would like to be doing more work on improved mining methods, better preparation techniques, and any other mining improvement that will benefit the industry and our program. The synthetic fuel plants I will describe later will operate seven days per week, 24 hours per day. We would like the mine to operate on this same sort of cycle and are prepared to support research that will lead to this.

Jan 1, 1970

By Leonard B. Rothfeld

For many years, pulverized coal (PC) boilers in utility power plants have been the dominant market for domestic coal. Today, two new coal utilization technologies challenge the PC boiler's dominance. Atmospheric fluidized bed combustion (AFBC) and "coal gasification/combined cycle" (GCC) stand on the verge of commercial demonstration in the utility environment at a scale of 100 MW. Developed over the past decade, these technologies respond to the demands for cleaner ways to burn coal and for more flexibility in fuel supply. In the near term, these are the "clean coal" technologies most likely to have a significant impact, because they are ready for commercial application. As for environmental acceptability, consider that just a few years ago one of the environmental slogans was "no coal in California." Indeed, the only large quantities of coal above ground in California at that time were in transit on the way to Asia. Today, thanks to new technology, we can point to two operational coal-burning plants in California and one in the works: * Cool Water GCC demonstration plant (100 MW) * California Portland Cement AFBC commercial cogeneration, near Riverside (190 000 lb/hr steam) * Energy Factors AFBC commercial cogeneration at Stockton, to be operational 1988 (44 MW)

Jan 1, 1987

By Y. H. Zhan

A new P(MAAA) latex was developed and used in separation of ultrafine apatite from calcite and silica by means of selective flocculation. The latex was found to flocculate selectively apatite from apatite/calcite and apatite/silica mixtures in the presence of sodium tripolyphosphate and sodium silicate over a pH range from 9.1 to 9.4. The separation of apatite from calcite was more selective with sodium tripolyphosphate, while the results of the separation of apatite from silica were better when sodium silicate was used. In the apatite/calcite system, 90% apatite recoveries into a concentrate containing 34% P2O5 were possible in the presence of 4 mg/l of sodium tripolyphosphate at a latex dosage of 2.2 kg/t. In the apatite/silica system, 80% of apatite could be recovered into a concentrate containing 33% P2O5 in the presence of 20 mg/l of sodium silicate at a latex dosage of 1.1 kg/t. Deposition tests were used to study the interaction between the latex and the mineral surfaces. The results revealed that deposition density of the latex on apatite was higher than on calcite; the differences between the deposition onto these two minerals were higher at pH 9.2 than at 7.2. The results point to the stronger interaction between the latex and apatite surface when compared with the latex-calcite interactions.

Jan 1, 1998

By Diler Katircioglu-Bayel

This study aims to investigate the effect of combined mechanical and ultrasonic milling on the size reduction of talc. Firstly, the talc sample was wet ground in a stirred media mill for five different times (30, 60, 90, 120, and 150 min), and the optimum result was subsequently achieved with treatment by ultrasonication. The effects of amplitude (20, 35, and 50 μm), solid content (2.5, 5, 7.5, and 10%), and sonication time (60, 120, and 240 min) on the sizes of the final product were investigated. The pre-milling by wet grinding caused a decrease in the grinding resistance of talc. Sequential ultrasonic treatment, which was applied to the talc sample, generated smaller particles in comparison to those acquired by stirred media milling alone. Experimental results were assessed based on the product particle size (d10, d50), reduction ratio, and specific energy consumption. Submicron particles prepared by ultrasonic treatment were perfectly stable compared to stirred media milling alone as investigated in terms of particle size. In addition, the effects of mechanical and ultrasonic milling on structural properties of talc particles were characterized by XRD analysis.

The purpose of this paper is to present validation studies of the mine-fire simulator using data gathered from an actual mine fire which occurred in November 1991 at the Pattiki Mine. To develop the model of the ventilation system with the fire in this validation study, the following adjustments were made: (1) flow and gas distribution in the entire ventilation network, and (2) fire parameters matching the data recorded by the monitoring system. After close correlations between simulation and real data were achieved, additional analysis of the ventilation system with the mine fire was performed. Presented and discussed in this paper are the following stages of the fire at the Pattiki Mine: (1) early fire (before the fire was detected), (2) preparation for and fire fighting with water, (3) fire sealing, and (4) fire extinguishing. This study evaluates the suitability of the computer software package for modeling underground fires. The paper also discusses the importance of the on-line monitoring system for the validation process.

Jan 1, 1995

By J. Noll, A. Miller, J. Volkwein, C. Pritchard

Hecla Limited, Magee Scientific and the U.S. National Institute for Occupational Safety and Health (NIOSH) combined efforts to evaluate an in situ air filtration system for use in an underground mine environment. The purpose of the collaboration was to determine the efficacy of such a technology for reducing the concentration of airborne diesel particulate matter (DPM), with the aim of improving air quality in underground hardrock mines. A secondary goal was to evaluate the use of an aethalometer as a means of real-time measurement of black carbon as a surrogate for DPM. The evaluation included measuring the DPM-capture efficiency of the filter when it was preloaded with dust. Toward this end, rock dust was introduced at the filter inlet to create a dust layer on the filter surface, with the intent of providing improved capture of the much smaller DPM particles. The filtration efficiency for DPM was assessed by comparing measurements of DPM taken at the inlet and outlet of the system, using both realtime and time-weighted-average approaches. The real-time measurements were performed with a Model AE33 aethalometer, and filter samples analyzed by the NIOSH 5040 method were used to assess the effects of the system on time-weighted-average concentrations of total carbon. Results showed a reduction in DPM concentrations in the range of 82 to 89 percent. While the calculated efficiencies based on the two different measurement methods were similar, the DPM levels reported by the aethalometer were higher, possibly due to differences in the performance of the size selectors used for the two methods: impactors versus cyclones. More research is required to develop a robust correlation between the two methods to support the use of the aethalometer in future mining applications. The advantages of the aethalometer are that it can measure and record DPM levels for weeks at a time and can be directly connected to a mine monitoring system, potentially at multiple locations. Ideally, such data can be used to initiate the startup of the filtration system should DPM concentrations reach an action level. This work demonstrated that in situ filtration systems, modified to collect DPM and coupled with real-time monitoring, show promise in reducing DPM concentrations in the mine environment.

Mar 1, 2017

"INTRODUCTION In recent years, there has been increasing focus on environmental and social impacts of the extractive industries, climate change and resource scarcity. The concept of the circular economy aims to replaces the “take-make-dispose” economic model with one that eliminates waste of all kinds and is restorative by design. Such closed-loop systems implicitly aim to reduce the quantity of primary extracted materials entering the economy, thereby affecting supply and demand dynamics, hence mining industry economics. For the metals industry, the ability to engage in, or adapt to the circular economy can be heavily affected by industry structure and geographical factors. Eco-efficiency initiatives that reduce waste and environmental impact may help the mining and metals industry align with some of the goals of the circular economy. This paper focuses on base metals, and explores case studies in copper, lead and zinc. It analyzes primary and secondary metal production, and recycling. It examines company structures and how these affect engagement with the circular economy. CIRCULAR ECONOMY PRINCIPLES Ellen MacArthur Foundation (2012) describes the circular economy as “an industrial system that is restorative or regenerative by intention and design”, which “replaces the ‘end-of-life’ concept with restoration”, and “aims for the elimination of waste through the superior design of materials, products, systems, and, within this, business models”. The concept is systems focused. For materials such as metals, a series of loops are considered, including maintenance of devices, reuse, refurbishment and recycling. Potential methodologies to achieve circular economy outcomes include disassembly and reassembly of manufactured goods, leasing rather than buying major appliances, and converting to renewable energy sources. The circular economy is partially aligned with the principles of eco-efficiency, which relate to reducing the environmental impact per unit of a material produced. PRIMARY AND SECONDARY METAL PRODUCTION Base metals (copper, lead, zinc and nickel) are essential ingredients in modern economies and are key commodities produced by the global mining industry. Metal production can be categorized as primary or secondary. Primary metal comes from the processing, smelting and refining of metal content extracted from ores, while secondary production comes from metals recovered from recycled streams (e.g. recycled lead-acid batteries, copper wire scrap, etc.). Metals are stored in natural, anthropogenic in-use and anthropogenic waste stocks. An example of the stocks, flows and processes associated with global copper extraction and use is shown in Figure 1."

Jan 1, 2018

By G. Pan

Although geostatistical techniques have been widely accepted as the standard methods for reserve calculations in the mining industry, the production data of many mines frequently differ from geostatistical estimations based on exploration and development drilling. The discrepancies in recovered metal amounts, commonly in the range between 10% and 30%, are related to different factors. Major causes vary from mine to mine. A common cause, however, is the ignorance of important geological constraints in reserve modeling. Three major factors appear to be related to such an unfortunate fact: 1) modelers are over-confident on geostatistical techniques, 2) it is difficult to establish geological models, and 3) mine schedules are too tight to allow detailed geological modeling work. Defining mineralization envelopes has been a major effort in geological modeling. Past experiences have showed that geological modeling is much mo~ demanding than the choice of sophisticated kriging estimators. Since building envelopes for complex ore bodies can be extremely tedious and time-consuming, computerized approaches are badly needed for mine modelers. A comprehensive procedure reported here is referred to as probability-assigned constrained kriging (PACK), which includes a built-in method for defining 3-d mineralization envelopes. The modeling technique is fast and accurate for complex precious metal deposits. The technique is demonstrated on a gold deposit. The estimation results are compared with blast-hole based production panels, showing that the estimated tonnage is 2.2% larger than the actual production and the average grade is 2.6% lower.

Jan 1, 1994

By L. B. Phelps

Many coal mining companies have potential surface mine reserves which either are known or suspected to have had prior drift mining activity on them. In many cases, there is no documentation on these mines or at best, very fragmented records. These undocumented abandoned underground mines are creating engineering, financial, and environmental difficulties and concerns for both surface coal mine operators and regulatory personnel. This paper examines the use of resistivity techniques in detecting entries of abandoned drift coal mines. The detection of such a drift mine entry would confirm the presence and orientation of an abandoned underground coal mine.

Jan 1, 1985

By Randall D. Peterson

Strip mining with draglines and other surface equipment has traditionally been the method of choice for mining shallow deposits. This is particularly true for soft deposits that require little or no blasting. High rates of productivity and low operating costs have set this standard. However, these methods can be improved. Strip mining methods are batch processes and difficult to accommodate in processing. Moreover, they are encumbered with overburden removal, reclamation expense, and human inefficiencies. This paper describes the invention of a novel shallow earth mining technique called the Softwall Mining Method. Softwall Mining is an adaptation of longwall mining for loose earth conditions. The method was specifically invented for recovering phosphatic clay ore from beds in North Central Florida, but is likely to be suitable for a number of other minerals as well. Potential deposits for which the method may be well suited include placers, disseminated deposits in soft host rocks, bauxite, soft coals and lignite deposits, and other deposits where overburden will subside readily and where the ore can be hydraulically broken and slurried. Unit operating cost advantages are expected over the current dragline systems used. The Softwall mining advantages are its high rates of productivity, control and automation of the mining process, reduction of dilution and waste, and elimination of the majority of stripping and reclamation.

Jan 1, 1998

By Michael A. Werner

"A Yieldable Structure for Use in Areas of High Rock Stress & Deformation." Rock stress of up to 9000 psi have been recorded in the mines of the Coeur d'Alene Mining district. Associated with these large stresses are rock fractures and deformation. In order to maintain openings required for mining, large wood preparation structures are constructed to provide access to the work areas for men and materials. These wood raise preparation structures are costly to construct and maintain. Therefore a steel-foam concrete structure was designed and proposed for testing which would be less costly to construct, require no maintainence and maintain its structural integrity while allowing up to 53 inches of wall rock deformation.

Jan 1, 1984

By Richard Chojnacki

The western united States is not usually noted for the production of fluorspar; however, many significant fluorspar districts do occur in the Rocky Mountain region and constitute a resource of sizable dimension and major potential. This is particularly true within the area of the West served by the rail lines of the Union Pacific Railroad (see Figure 1). Fluorspar deposits near the Union Pacific have produced over 1.3 million tons of finished fluorspar products from 2.3 million tons of ore. Approximately 80% of this production was of acid-grade and 20% of metallurgical-grade fluorspar. Production of ceramic-grade was negligible. Through the years substantial production has come from eight mining districts. Five of these have produced metallurgical-grade and three acid-grade. The best-known fluorspar producing area in the West is the Jamestown Mining District. It was one of the first producers of fluorspar in the western United States and is estimated to have produced over 500,000 tons of finished fluorspar from over a million tons of ore. The district encompasses approximately 36 square miles in central Boulder County, Colorado, about 9 miles northwest of the City of Boulder. Although small shipments were made from the district as early as 1873 or 1874, significant sustained production was not achieved until 1940 when the General Chemical Company, now a division of the Allied Chemical company, acquired the Alice, Burlington, Chancellor,

Jan 1, 1971

By Khosrow Badiozamani

Traditionally the mining industry has been lagging in application of computers in their daily or long range plan activities compared to other industries. The question then remains as to how the technology of higher computing capacity for less cost is going to affect the mining industry and how the lukewarm reception of engineers in acceptance of computerized mine planning in the past is going to change because of the new wave of high techology. These questions and the reasons for the lack of usage of computerized mine planning systems by engineers will be evaluated in this paper. In addition, alternatives available to the mining industry will be analyzed and the direction of the future "user friendly" software will be discussed.

Jan 1, 1984

By Mikael Ramström, Mark Board, Clayr Alexander, Wes Johnson

"The Coeur d’Alene mining district in northern Idaho was first discovered more than 130 years ago and has been the most prolific silver producer in the United States. The Lucky Friday Mine of Hecla Mining Co. (Fig. 1) is the oldest (76 years) and deepest mine in the district, producing approximately 725 t/day (800 stpd) from narrow, vertical lead-zinc-silver veins. Cut-and-fill stoping is currently employed at depths to about 2.3 km (7,500 ft) below ground surface, making it one of the three deepest mines in the western hemisphere. The #4 Shaft, a winze collared at approximately 1.8 km (5,900 ft) below surface and extending to a depth of nearly 2.9 km (9,600 ft), was recently completed to exploit the high-grade 30 Vein, whose resource has been identified to at least 3 km (9,700 ft) in depth.As with other deep mines worldwide, a number of challenging engineering issues occur, including: high in situ rock stress, squeezing ground, seismicity, high in situ rock temperature that requires refrigeration, diesel equipment that generates diesel particulate matter (DPM) requiring high ventilation airflow rates and long travel times for worker transport to mining areas.This article describes the methods that Hecla Mining Co. has employed during the past 50 years to combat these issues, with emphasis on the current efforts to implement continuous, mechanical mining with automated or teleremote operation and to introduce electric and battery-powered equipment to minimize refrigeration and ventilation requirements for the removal of DPMs.Geology and in situ stressThe host rock mass is an extremely thick sedimentary sequence (the Belt Series) that has been tilted vertically by mountain building. The rock mass in the current section of the mine consists of weak, heavily foliated argillites and stronger, bedded silty-argillites termed siltite. The vertical veins (80° to 85° dip) are parallel to the foliation with an approximate width of around 3 m (10 ft). There are two regional, vertical faults that parallel the vein; one forming the hangingwall of the orebody and one approximately 90 m (300 ft) in the footwall. Additionally, there are several thin, rough northdipping faults that occur in the footwall of the vein which terminate on the major vertical faults.Both the argillite and vein package rock have moderate strength, with uniaxial compressive strength averaging about 100 MPa (14,700 psi with a range from about 70 to 125 MPa), and are moderately abrasive, with CERCHAR abrasivity index of 2 to 3. The major in situ stress is horizontal and oriented in a northwest direction with magnitude about 1.5 times the vertical stress. Consequently, the Lucky Friday stress magnitude at depth is analogous to significantly deeper South African gold operations."

Jan 12, 2017