Search Documents

By J. J. Bean

The development drilling program of the Copper Cities mine indicated that the molybdenum content of the ore would be about 0.011% MoS2' The molybdenum content of the Miami mine at the same time was about 0.025% MOS2' The Miami mill had a very successful molybdenum operation which used bleeder turbine steam from the Miami power plant for the steaming operation. The much lower grade of the Copper Cities ore, the absence of a source of low cost steam and the use of sodium aerofloat as the copper collector which Miami experience indicated did not respono readily to the steaming technique made very doubtful the success of a similar operation at Copper Cities. However, the relatively few pounds of copper that could be recovered from the low grade Copper Cities heads made very desirable the recovery of the molybdenwa,as a source of additional revenue. Accordingly, shortly after the Copper Cities mill began operation, a research program was instituted to develop a suitable method of molybdenum recovery. This program explored first, the successful steaming process then in use at Miami and as expected, found it unable to decompose the sodium aerofloat copper collector. The known chemical depressants were then tried without much encouragement. Finally the copper concentrate was dried, not roasted, to 2-3% mOisture and this along with sodium ferro-cyanide and cyanide resulted in sufficient copper depression that a final molybdenum concentrate containing 1.0% CU could be made. The bench scale testing was followed by pilot plant testing. Sixteen

Jan 1, 1972

By T. Hollenberg, N. Nolten

The mining industry is one of the major energy consumers in Namibia. Energy costs increase the operating costs of Namibian mines, in particular, the processing plants, and result in an overall increase of production costs. A substantial part of the energy used is directly imported from South Africa. The cost of energy has been increasing rapidly in the past few years and will most likely continue to do so in the future. In 2015, the average wholesale price for energy from national power utility NamPower was US$87/MWh after rising more than 12 percent annually in the two previous years. At peak times, which are early in the morning and late in the evening, imported-energy prices are extremely high and have to be factored into the electricity tariffs. This problem is expected to intensify due to a projected 4 percent annual increase in energy demand. A major target of the Namibian mines, therefore, is to consider possible ways to address energy-saving challenges and to investigate possibilities for the mines to generate electricity internally during peak times. This is in alignment with the mines’ strategic plans and objectives to reduce total energy consumption and costs from both national and foreign electricity suppliers. In this paper, we explore addressing some of the key energy consumption and optimization challenges through process energy reuse and solar energy production to decrease demand for imported energy through a case study carried out in cooperation with Skorpion Zinc Mine and Refinery.

Jan 1, 2018

By D. S. Yantek, L. A. Alcorn, M. J. Lowe, H. E. Camargo

U.S. National Institute for Occupational Safety and Health (NIOSH) studies show that 43.5% of surveyed coal preparation plant workers had noise exposures exceeding the U.S. Mine Safety and Health Administration permissible exposure level of 90 dB(A). Sound levels around vibrating screens in these plants often exceed 90 dB(A). NIOSH is currently developing noise controls for horizontal vibrating screens. To characterize noise sources, NIOSH researchers performed sound pressure level (SPL) measurements on a vibrating screen at their Office of Mine Safety and Health Research laboratory in Pittsburgh. The results show that the entire screen contributes to noise below 1 kHz, and the vibration mechanism housings are most significant above 1 kHz. Constrained layer damping (CLD) treatments and an enclosure were used to reduce mechanism housing noise in this range from 1-10 kHz. These were evaluated using sound power level measurements according to ISO 3744. The CLD treatments reduced the A-weighted sound power level by 3.1 dB in the 1 to 10 kHz one-third-octave bands. A panel-on-frame vibration mechanism enclosure using various types of panels further reduced the A-weighted sound power level from the CLD configuration in the 1 to 10 kHz one-third-octave bands by 3.7, 4.0, and 3.9 dB for aluminum, steel, and Dynalam™ panels, respectively. The combination yielded a 7 dB reduction from baseline in A-weighted sound power for the same frequency range.

Jan 1, 2011

By Scott Burchmore, Jason Emery, Michael Melville

This paper presents best practice data management for monitoring of extensometers in Australian underground coal mines. This work is based on the combined experience of the authors and the available literature. The information and ideas presented herein are a culmination of many years of database development founded from mine site-based ground support design, underground inspections, extensometer data management and data analysis. Each author has more than ten years’ experience as a practicing geotechnical engineer at several operating industry wide research project focused on utilizing mechanical extensometer data for data analytics and machine learning. Principal hazard ground control management plans, stipulated in Australian coal mining legislation, outline the mandatory installation of ground monitoring devices during routine mining activities. After 20+ years of data gathering the barrier to implementing modern data analytics remains the challenges imposed by inconsistent data structure and data quality. This inconsistency is still routinely found between sites, companies and mining regions. Through the relatively simple application of a standardized database structure, the potential to shift from simplistic tracking of trigger levels, siloed at individual sites, to an industry standard method for compilation & comparison of monitoring data is enabled.

Jun 25, 2024

By David H. Carlson

The paper presents background information including data on diesel exhaust pollutants, amounts produced and standards, a desscription of mine characteristics that affect air monitoring techniques and a review of portable measurement techniques and instruments for gas and particulate matter sampling. A general review of the laboratory and field research being conducted at Michigan Technological University in the area of diesel emissions is presented. The facilities involved with this research are also described. These are the Experimental Mine, the diesel dilution tunnel test cell, the Mine Air Monitoring Lab (MAML), the portable instruments and the production mines used.

Jan 1, 1979

By E. R. Mueller

The natural lives of machines and components vary tremendously! Maintenance managers struggle constantly to maximize their equipment lives while minimizing their maintenance costs, but they normally lack the tools and techniques they need to do this properly. This paper proposes a methodology based on probabilities of failure and expected values for repairs that recognizes the variation among individual machines and components as well as the high costs associated with catastrophic failures. It enables a user to determine the optimum change-out intervals for many types of equipment. The approach proposed here is sophisticated enough to be reliable but simple enough to be applied by the maintenance staff on the shop floor. It will complement existing preventive and predictive maintenance programs.

Jan 1, 1995

By M. R. Rosen

A technique is presented for simple characterization of the performance of flocculents in various mining applications. The method utilizes three key parameters obtained from raw settling data and combines them into a single athematical parameter called the desirability coefficient. The first two parameters are the timesrequired for the slurry-supernatant interface -to fall to two selected fractions of the starting height, and the third is the clarity of the supernatant liquid. The relative values of the three parameters may be assigned different weights in order to make them correspond with laboratory and field performance requirements of a particular industry. Provision is also made of an, internal comparison of test flocculant data with that of a control.

Jan 1, 1980

By N. R. Sainath

This paper discusses the results of a laboratory investigation carried out to study the microscale flow characteristics of copper ores and the variation in flow behavior resulting from flow of leach solution. Fractures in 1.5 and 4 inch diameter cores were mapped by visual inspection. The cores were stressed in a triaxial stress field representative of in situ conditions. The permeability of the samples to water was then estimated. The samples were exposed to 20 g/l sulfuric acid and the experiment repeated. The Permeability of unleached samples ranges from 10-1 to 10-19 m2 and it increases as leaching progresses. The porosity variation and the rate of recovery of copper from the specimen during leaching were also studied.

Jan 1, 1991

By D. W. Gunkle

Processing of various ores and materials in a reducing atmosphere has been done for many years. However, the typical device currently used is a large, often high maintenance, expensive piece of equipment; the rotary kiln. While it is a very reliable and a proven technology, the rotary kiln also has its limitations. It is limited by its ability to process very fine materials without creating a huge dust loss to the air pollution control equipment. This leads us towards the development of an alternate technology; the Gas Suspension System. Gas suspension preheating of various materials has been in commercial use since the early 1950's, but recently has been expanded to include Gas Suspension Reduction. Laboratory experience has proven successful on several materials; Nickel Laterite Fines, Iron Ore Fines, Fluorspar, and Clays. The gas suspension reduction system has many advantages over the conventional reduction kiln when processing fines. They are; lower cost, more fuel efficient, able to process fines, less real estate required, etc.

Jan 1, 1998

By Cesar A. Busnardo

The carbonatite orebody in Jacupiranga is situated some 230km (140-mi) southwest of Sao Paulo and is mined by Serrana S/A de Mineragao, producing an apatite concentrate for fertilizer production and a calcite tailing for cement manufacture (see Figure 1). The orebody (Table 1) is mined by open pit and the total production is 4.5 million mt/year of carbonatite ore with a further 2.2 million mt/year of overburden. The carbonatite low-grade ore (Table 2) is fed to the concentration plant at 460 mt/h , comprising of four parallel lines of grinding, by rod mills 2.7m x 4.5m (9 x 15-ft), operating in closed circuit with hydrocyclones. The grinding circuit product is deslimed in four stages using hydrocyclones and the deslimed product is conditioned with corn starch and subsequently floated, using fatty acids as collector to, recover the apatite.

Jan 1, 1985

By S. Daniel Thompson

In underground coal mining, the specification and control of belt and bunker capacities are complicated by (1) stochastic and intermittent conveyor loading, (2) a limited ability to reduce surge at the mine face, and (3) occasional overlapping of loading from two or more mine faces on the conveyors. Recently, because of longwall mining and other factors, the capacity requirements of most mine conveying systems have risen substantially; as a result, efficient capacity design and control have become important mine planning issues. This paper reviews these design issues and their associated modeling procedures. Design considerations and modeling difficulties are also examined.

Jan 1, 1996

By R. P. King

The MODSIM mineral processing plant simulator is used to find optimal combinations of target separation specific gravities in a typical modem coal washing plant. A plant that is set up with these optimal targets can deliver up to 10% more yield at the same ash content as the same plant set up with separation targets chosen by conventional methods. MODSIM is the only simulator currently available that can simulate the liberation of pyrite and other mineral matter during open-and closed-circuit grinding operations. The simulator can therefore be used to assess the benefits of grinding operations in the flowsheet.

Jan 1, 1997

By Lawrence Lien

The reduced need for traditionally trained and educated personnel in the mining industry is systemic to the changing mining industry. Universities and other training institutions are meeting the traditional skill needs required by the industry, but are the skill needs going to be the same in the near future? The answer may be no. Mining is changing because of increased liabilities and costs of environmental and safety is-sues; lower grades of minerals in traditional mining activities and the advent of new bio-chemical processes and robotic equipment. More productive and economic alternatives, and larger, more sophisticated and automatic equipment, are also changing the industry. Engineering is more specific, accurate, precise and expensive. Measurement is more thorough and timely of progress, production, costs and productivity. And, the industry will likely be engaging in more undersea mining, possibly space-based processing, less human interaction and more remote control of events than was previously thought possible.

Jan 1, 2011

1. Theory of Wet Dust Suppression Techniques Wet dust suppression is the utilization of a liquid for the control, reduction or elimination of airborne dust, or the suppression of such dust at its source. Effective control involves: a. The confinement of the dust within the dust producing area by a curtain of moisture. b. The wetting of the dust by direct contact between the particles and droplets of moisture. c. The formation of agglomerates too heavy to remain airborne, by combining small dust particles with each other and with the droplets of liquid. From the standpoint of economy, availability and safety, water is the ideal fluid. From the standpoint of effectiveness, however, it leaves much to be desired. As a result, a tech¬nique has been devised in which very small percentages of specially formulated dust control compounds are blended with water to greatly enhance its dust suppression qualities. The terms "dust control compounds, wetting agents and surface active agents" are frequently used interchangeably. Although dust control compounds represent a specific type of wetting agent, a great many wetting agents are far from satisfactory for dust control. "Wetting Agents" is a broad category which covers such items as emulsifiers, solubilizers, detergents, foamers, penetrants, thickeners, etc. Dust control compounds, on the other hand, are carefully formulated blends in which one or more special surface active agents have been incorporated.

Jan 1, 1972

By B. G. Kelley

The MIDREX® Direct Reduction Process was developed during the 1960s by the Midland-Ross Corporation, which had pioneered shaft furnace technology and stoichiometric gas reforming for use in processing minerals. In 1969, the first MIDREX® Direct Reduction Plant was built in Portland, OR. Since then, 49 additional modules have been sold in 18 countries. For the last ten years, over 60 percent of the world's direct reduced iron has been produced in MIDREX Plants. During the quarter century since commercialization, many technical improvements have been made, including larger shaft furnaces, in-situ reforming, greater heat recovery, improved catalysts, and hot briquetting. Midrex continues to enhance the technology in the areas of economy-of-scale, energy efficiency, alternate fuels, and raw material flexibility.

Jan 1, 1998

By John D. Price

The solution to the problem expressed in the title of this paper might well be condensed into one word, AUTOMATON, But if I were to stop there, even though most of you might applaud, I am afraid that a one-word paper might not justify my coming to this meeting, So let?s explore the matter and try to learn if and to what extent the science of automaton can be applied to the problem of coal cleaning. In taking this approach we must, of course, by-pass the fact that plants In this Country and aborad have been automated to a greater or lesser extent. We will explore the matter from the beginning and not merely take the approach that because others have done it we can do it also. First, let us see just what is meant by automaton.

Jan 1, 1959

Simulation has established itself as an accepted tool for the design and optimization of complex minerals processing plants. This paper addresses the use of simulation as a tool for the design and optimization of carbon-in-pulp and carbon-in-leach (CIP/CIL) plants. The complex, interactive nature of CIP/CIL plants makes detailed experimentation an expensive and time consuming approach to CIP/CIL plant design and/or optimization. This paper discusses a simulation-based software tool that can make the process of CIP/CIL plant design and/or optimization much more cost effective. Many of the issues and problems pertaining to the use of simulation for CIP/CIL design and operation are generic. Thus, this paper also attempts to highlight generic issues that must be solved before simulation will become a more widely used design and optimization tool. Requirements for the application of simulation for CIP/CIL plant design and optimization are highlighted. Similar problems and issues can be identified for most mineral processing plants.

Jan 1, 1994

By James L. McGregor

St. Joseph Lead Company has been paying incentive bonuses for well over 40 years. In 1958 almost half of St. Joe's 1,860 employees in Southeast Missouri received some form of incentive bonus in addition to their guaranteed wages. There are very few payroll jobs in St. Joe s Southeast Missouri organization that lend themselves to a reasonably good measurement of production or quality, or both, where an incentive bonus is not paid. The term "Incentive Bonus" is used to differentiate betwen bonuses that are based on quantity or quality of work, and those that are merely additional pay of a standard amount per hour or day because of an employee being temporarily assigned to some unusual task, An employee temporarily assigned to a job where the working conditions make the job performance unusually difficult or where a special skill is used is often given a bonus of some standard amount per hour or shift in addition to his usual rate. This is merely a convenient way of paying something extra without disturbing the normal rate structure. Actually, it is differential pay similar to that almost universally paid for evening and night shift work. Bonuses of that type are not being considered in this paper. The basic reason or theory for paying incentive bonuses 9s to get improved production at lower cost, Unfortunately, it is often difficult, if not impossible, to find a yardstick by which it can be definitely proved that a particular bonus plan is accomplishing its purpose, It becomes, then, a matter of judgment on the part of management personnel as to the value of the bonus plan. The fact that St. Joe Lead Company has continued to pay bonuses for over 40 yews and has increased the number of bonus schedules used attests to a definite belief that they are beneficial to the company's successful operations.

Jan 1, 1960

By Gill Montgomery

The problems of the domestic merchant fluorspar producers are more or less common with those of many other producers of metallic and non-metallic minerals. For more than ten years the American fluorspar producers have seen an ever lowering price in the market-place for the fluorspar product, while their labor and material costs-continue to mount steadily. This cost-price squeeze has forced out of business all but a few of the merchant producers, and only two captive producers continue to operate, and one of them has announced early curtailment. The prices of domestic fluorspar, of all grades, have declined because of the competition from cheaper foreign imports, principally from Mexico, Spain and Italy. Tariff protection on fluorspar, particularly on the highest or acid grade, has never been sufficient to cover the production cost differential between foreign and domestic fluorspars. Low ocean and barge freight rates have also contributed to the barring of the product of domestic mines from, the major consuming centers along the Gulf and East Coast. Because of the freight disadvantage, all but one or two fluorspar producers in the western states have had to suspend business. More than 80% of the domestic fluorspar is being produced in Illinois and Kentucky fluorspar districts which adjoin on both sides of the Ohio River.

Jan 1, 1964

By I. O. Otunniyi

The natural hydrophobic response flotation method for beneficiation of printed circuit board comminution fines (PCB CF) still requires many studies to further basic understanding of the process and the flotation traits that the PCB CF presents. Varying particle size distribution (PSD) and water recovery under the scheme show that higher mass pull, obtained at the finer PSD, gave lower water recovery but higher value loss. The reverse also holds: the least mass pull at the coarsest PSD used, -106 + 75 µm, gave the highest water recovery per unit mass pull with the highest reverse recovery. This is unlike what obtains in primary resources processing, where higher water recovery is often with increased fines entrainment. The reverse recovery loss here is, therefore, more due to entrapment with the heavy mass pull characteristic of the method than to the entrainment of value with water. Other peculiarities of the system observed are discussed, with the goal of improving the performance of the process, and broadening the general knowledge of flotation systems.