Search Documents

By D. A. Paice

Under the first phase of this contract as reported in the Phase I report it was determined that certain types of commercially available molded case breakers are capable of interrupting mine dc power supplies of nominally 300 volts or 600 volts rating. These circuit breakers incorporate conventional overcurrent trip units but also can be operated by means of low power signals fed to a shunt trip coil. Further development in the Phase I program produced a means whereby a discriminating circuit breaker detector unit could sense the presence of illegitimate loads on the dc electrical system and cause the circuit breaker to trip. The detector unit operated by detecting the presence of 3000 Hz currents which were generated in the illegitimate loads by means of a 12 volt, 3000 Hz signal applied to the dc system. Further development of the program has continued in Phase II with the aim of verifying the practicability of the complete discriminating circuit breaker concept and developing other types of equipments required to implement a system. These other equipments include electronic means for raising the apparent impedance of high power legitimate loads and static filters for smaller loads. The results of laboratory work and limited underground tests have been successful. This report describes the system and the tests that have been conducted on the various equipments that comprise the complete Discriminating Circuit Breaker Concept.

Jan 1, 2012

By Richard Quirk

This report describes methods and techniques employed by The Glidden Co. of Cleveland, Ohio, in explorating an ilmenite-bearing sand deposit in Ocean County, New Jersey, during 1960 to determine ore reserve potential and the feasibility of mining and establishing a milling plant on the property for the production of ilmenite concentrate. The property covered approximately 1,250 acres. Comprehensive sampling by water-jet drilling indicated the deposit averaged 20 feet in thickness and contained 4.5 percent heavy minerals, of which 80 to 85 percent was ilmenite and leucoxene. Average depth of the water table as determined by auger boring was 16.8 feet. Pilot plant tests indicated that circular concentrators in combination with spiral concentrators would recover at least 80 percent of the heavy mineral content of the sands. It was estimated that sufficient ore reserve tonnage had been developed to supply the company's Baltimore chemicals division, pigments department, with a suitable grade ilmenite concentrate for a period of 20 years at the present rate of pigments production. The property was designated as Lakehurst mine and plans are in progress for mining development and plant construction.

Jan 1, 1963

By James C. Fowler

This report contains a description of the contract activities performed by ENSCO, Inc. under contract H0292025. The purpose of this project was to prove the feasibility of detecting hazards in a coal seam using a synthetic pulse radar. This work was conducted in three phases. The first was an analysis of the types of errors which might cause problems. The second was to build a breadboard radar and the third phase was to conduct a field test with the system. The work from each phase is discussed and the results of the field tests are presented. These results show propagation of the radar signal through 200 feet of coal along with reflections from 50 feet away. The final section contains recommendations for future development.

Jan 1, 1981

By Charles H. Simmons

Two versions of a VF transceiver to aid in location of trapped miners has been developed and tested. The belt worn model was produced in both transmitter and transceiver configurations. In addition, a quantity of the belt worn models were fabricated using aluminum wire instead of copper in order to reduce unit weight. Ten prototypes of a battery cap model VF transceiver were also fabricated demonstrating further unit size and weight reduction while maintaining electrical performance. Samples of- both versions were tested environmentally and the test data is included in this report. While both versions of the VF transceiver are similar electrically, and are constructed using convential manufacturing techniques, the battery cap model realizes a lower total weight, smaller volume and production cost than the belt worn version. Operationally, the battery cap model assures that the VF transceiver will always be with the miner.

Jan 1, 1981

By Joseph A. Vanous

The inductive communication system was developed under this contract for use in the hoist of deep mines. This program was a four phase program with experimental dual frequency equipment resulting from Phase I, emergency single frequency equipment developed under Phase II, and equipment documentation required under Phase III. An additional emergency system was provided under Phase IV.

Jan 1, 1976

By Galen G. Waddell

This report describes a method of measuring and analyzing the initial deformation which occurs in the medium surrounding a mine accessway as the opening is created. Discussed are (1) the hypothesis upon which the research is based; (2) the in situ rock-deformation measuring equipment developed; (3) the field tests, consisting of measuring the deformation of the medium around two 4-foot-diameter raise bores as the boring progressed; and (4) a finite-element technique to correlate theoretical with experimental results, using elastic theory. Described also are the raise-bore operation and performance. The instrumentation developed proved to have the sensitivity and resolution necessary to measure rock deformation around a full-scale raise bore during excavation. Tests show the relationships of rock deformation to progress of the raise boring and to time. The initial deformation of the opening appeared to be elastic. Using the deformation records and an estimated field stress, the modulus of elasticity was determined for the rock mass. In addition, the importance of this type of measurement in assessing support-problem areas is discussed.

Jan 1, 1971

By Peter G. Groer

The commonly used exact methods (1-2) to determine the WL measure the total a activity or the total number of a counts during three preselected time periods. Due to the half-lives involved (TRaB = 26.8 min, TRaC = 19.7) I these methods take 3S minutes to complete the a activity Ra measurements. Methods using the total a counts, obtained at times less than about one RaB half-life after the end of sampling run into statistical 214 problems. These methods are almost blind to RaB (Pb214) as a consequence of its relatively long half period (see above) and the fact that RaB is a ß emitter. The way out of this dilema is to measure RaB directly through its ß activity. Since RaB's daughter Rae (Bi214) is also a ß emitter, the two f3 spectra have to be separated to obtain RaB alone. How this is accomplished 1s described in subsequent sections describing the theory of the IWLM and its calibration. 2.0 THEORY The IWLM samples air for two minutes and counts this airs ample for two minutes starting 3 sec after the end of the sampling period. The instrument has three channels. The lower a channel, the upper a channel, and one ß channel. The total RaA counts observed are accumulated in the lower a channel, the total RaC? counts are stored in the upper a channel. The total ß counts from RaB and RaC are recorded in the ß channel. These three quantities are functions of NA, NB, and NC, the unknown concentrations

Jan 1, 1975

By Walter E. Pittman

In its role of providing technical assistance to the mining industry, the Bureau of Mines' Tuscaloosa Research Center has conducted research to develop trapped miner location systems which would aid in locating miners trapped by underground mining disasters. Efforts to produce electromagnetic systems for the location of trapped miners underground and to communicate with them were surveyed, from the 1920's to 1981. Theoretical studies of through-the-earth electromagnetic transmissions are described as well as studies of the electrical characteristics of various rocks, minerals, and soil. Several trapped miner location systems are reviewed including the Westinghouse systems, the DEVELCO system, and an automated three-dimensional location system, and the phase difference of arrival technique. Tangential research, relevant to trapped miner location systems is described. A comprehensive bibliography covering all aspects of trapped miner, through-the-earth electromagnetic location and communications systems is appended.

Jan 1, 1982

By Howard B. Hamilton

Laboratory performance of mercury filled current limiting devices (CLD) used for high speed switching of DC circuits (600 volts and below, up to 1000 amperes) using a system involving a parallel connected vacuum switch with CLD and an additional series connected vacuum switch was verified in USBM Contract #HO 357079. This report details analytical work and field experimental tests to predict and control voltage surges associated with the high switching speed associated with the switching system. It also details tests conducted to demonstrate the fault current limiting ability of the CLD. Problems associated with designing a fault current limiting system are discussed.

Jan 1, 1978

This report summarizes the results of several field tests conducted by Collins for the Bureau of Mines under contract S0122076 and contract H0232056. The field projects represent a part of Collins continuing effort on a broad study of coal mine communications. These experiments analyze the propagation characteristics of radio signals in a working coal mine environment. The intent of the program is to provide basic propagation loss characteristics by which we may evaluate various approaches to an integrated mine communications system. The goal of such a system is to satisfy both operational and emergency communications needs in the mine.

Jan 1, 1974

By Ivor Hawkes

This report describes the results of a study to evaluate new design concepts for percussive rock drills that will result in quieter machines. It is shown that by incorporating such features as an efficient muffler, a plenum chamber integral with the machine body, and shroud tubes around the drill rods, etc., noise levels are reduced from about 114 dBA to about 95 dBA with very little change in drilling performance.

Jan 1, 1977

By Peter P. Kopas

Study, analysis, fabrication and testing for canopies on Roof Bolters and Shuttle Cars in coal seams under 48?.

Jan 1, 1980

By Robert M. Baker

This document details the method whereby Allen Corporation of America gathered and analyzed data and developed an annotated bibliography of metal and nonmetal mine fire reports (1950-1979). The primary objective of this program was to develop the annotated bibliography which included MSHA accident reports and periodicals. Two additional objectives were to gather data on non-reportable fires and to conduct statistical analyses on the data to delineate trends. Data was acquired from three major areas: periodicals, MSHA fire reports, and mine safety directors. Data was separated into reportable fires (at least ½ - hour duration or injury), non-reportable fires, and opinion data. The data was then analyzed by time trends, state, ore, ignition source, burning substance, location, equipment, detection, duration, injuries, fatalities, and successful extinguishing agent. The authors make a number of recommendations: (1) improved stationary electrical equipment design and fire protection, (2) improved design of mobile equipment to separate combustibles from ignition sources, (3) improved maintenance, (4) improved housekeeping, and (5) improved training. The document is divided into two volumes and an appendix. Volume I contains data acquisition procedures, data analysis procedures, and conclusions and recommendations. Volume II contains a chronological list of mine fires and fifteen indexes to assist the reader in locating fire incident report of interest. The Appendix contains the annotated bibliography of over 300 metal and nonmetal mine fire reports and journal articles and a list of non-reportable fires.

Jan 1, 1980

By Albert Ketler

[Early Bureau of Mines research had produced a fluorescent mine illumination system which was approved by MESA under Schedule 29A for use as portable equipment Intense industry preference for machine-mounted hardware required a MESA 2G approved system. The modifications required to upgrade the portable system arc herein described.]

Jan 1, 1976

This appendix is composed of five sections, each of which is tabbed for ease of access. The sections are as follows: ? Fire incident report forms for underground mine fires. There is one form for each incident listed in Table II-1a. They are ordered chronologically with incident numbers corresponding to those in Table II-la. ? Fire incident report forms for surface mine fires. There is one form for each incident listed in Table II-lb. They are ordered chronologically with incident numbers corresponding to those in Table II-lb. ? Journal article report forms. There is one form for each article reviewed. They provide supplemental information to that contained in the fire incident report forms for selected fires. Index 11-14 keys the journal article report forms to the appropriate fire incident report forms. ? Non-reportable incident descriptions for underground mine fires. This is a listing of underground fires for which MSHA regulations do not require formal reports. ? Non-reportable incident descriptions for surface mines. This is a listing of surface fires for which MSHA regulations do not require formal reports. This appendix is intended to be used in conjunction with the tables and indexes contained in Volume II of this report and, as such, should be considered an integral part of Volume II. The indexes in the body of Volume II provide a means of ready reference to the underground and surface mine incident report forms. For those readers with interests other than those indexed, Tables II-la and II-1b can be used to locate specific incidents of interest. Complete incident information can then be obtained from the corresponding report forms in the first two sections of this appendix.

Jan 1, 1980

The safety analysis of shaft-sinking operations included a review of accident reports from coal and metal-nonmetallic mine shaft-sinking projects in the United States, a review of foreign and domestic shaft laws, and discussions with shaft contractors and Federal mine inspectors. Accident data were studied to identify the most common and the most severe types of shaft accidents and to determine their immediate and contributing causes. Additional factors such as worker training and experience, equipment and sinking procedures, regulations and enforcement practices were also investigated to determine their impact on shaft safety. The results of the study are summarized in recommendations for improved training of shaft miners and clarification of Federal shaft-sinking regulations. A guide to assist mine inspectors in examining shaft-sinking projects is also included.

Jan 1, 1977

By Donald H. Koch

The project investigated the impacts of coal and mineral storage piles on both ground and surface water quality. The study consisted of two major tacks, Task 1 had two phases. The first phase was field investigations in which ten cons and mineral stockpile sites (5 coal, 5 mineral: phosphate, lead, copper, iron, uranium) across the country were visited to determine the actual impart of coal and mineral stockpiles on writer quality. The second phase of Task I was a series of leaching experiments in which drainage from the ten coals and minerals was controlled and monitored to survey the extent to which storage piles release toxic ions to ground and surface waters. Task IT was n review of pollution abatement techniques with three generic treatment examples applied to lead-zinc ore, eastern coal, and uranium ore stockpile leachate. Major conclusions drawn from the completion of Tasks I and II include: water quality impacts are site specific, there is n high correlation between sulfide content of u material and its solution potential, and the selection of the best treatment alternative for n specific coal or mineral storage area must be based on site-specific criteria, pilot studies on representative leachate samples, and sound engineering design.

Jan 1, 1982

By Michael D. Balen

The Bureau of Mines (Bureau), in cooperation with the Alaska Division of Geological and Geophysical Surveys (ADGGS), conducted field investigations from 1987 through 1989 in the 5.7 million-acre Valdez Creek Mining District (VCMD) in south-central Alaska. The objective of the VCMD investigation was to evaluate the mineral resources and the mineral development potential of the mining district. The investigation was part of the Bureau's continuing statewide mining district evaluation program. Nineteen new mineral occurrences were identified as a result of this investigation. Reconnaissance placer sampling resulted in the identification of 10 previously unreported occurrences that primarily contain gold, however, some contain subsidiary platinum-group metals and/or tin. Reconnaissance lode sampling resulted in the identification of two gold-silver occurrences, three platinum-group metal occurrences that contain elevated quantities of subsidiary chromium, nickel and/or cobalt, three copper occurrences that contain subsidiary molybdenum or zinc, and one zinc occurrence.

Jan 1, 2011

By Dipak Sengupta

This study analyzes the safety, technology, and economic impact of eliminating safety fuse from metal/nonmetal mines, based on operation and manufacturer experience over the past five to ten years. If safety fuse is eliminated, blasting accidents will decrease with no technical impact except for some limited, specific applications. The economic impact will be minor for large operations, but will be significant enough for small operations that some small operations will likely close rather than change. The majority of the mines would probably change over, with the extra cost absorbed by the market. Elimination of safety fuse would have obvious impact on the two manufacturers of safety fuse; one manufacturer already produces an alternative system, and will remain unaffected; the other will be affected if they do not change their production strategy. There will be a very minor effect on the mining industry as a whole due to abolishment of safety fuse from the standpoint of employment or production.

Jan 1, 1980

By James H. Prout

Roof warning signals were studied in 18 mines covering 5 coal seams. The results of this study confirmed that roof talk must be interpreted for each individual mine after all other conditions are present that indicate danger of roof fall. Characteristics of roof talk pulses were studied to ascertain features used in interpretation. Roof talk pulse decay time was found to be typically 0.1 to 0.5 seconds depending on the dimensions of the entires. Time between roof talk pulses was found to correlate inversely with the degree of danger under certain conditions. Roof talk and machinery noise recordings obtained during this study were used for subjective tests of ear protectors in a simulated coal mine noise environment. These tests required a detailed interpretation of roof talk and yielded results with high statistical power. Results of these tests showed that the use of personal ear protectors in high noise levels does not degrade a miner's ability to discriminate speech and roof talk. A training course was developed to encourage coal miners to pro-tect their hearing by proper use of personal hearing protectors.

Jan 1, 1973