Search Documents

By Oliver C. Ralston

DURING the development of froth flotation for the treatment of sulphide ores, a certain amount of information was collected about a few of the nonmetallic minerals, and occasionally the gangue minerals in the sulphide ores showed an embarrassing tendency to float. However, for many years efforts were expended to develop reagents that would cause wetting and depression of these minerals. Among the nonmetallics, the minerals sulphur, graphite, and talc probably should be classified as 'natural floaters', and perhaps sericite. They respond to almost any type of flotation reagent, and their beneficiation by flotation had been attempted years ago. Flotation of sulphur is now common practice, and graphite was concentrated during the World War in many mills, most of which have now closed down. A talc mill has just been constructed, and another may soon be erected. Second to the 'natural floaters' come the 'easy floaters', cassiterite, fluorite, barite, mica, colloidal gangue, and paper pulp from white water of paper mills. That these materials responded to some of the early flotation reagents, as oleic acid, has long been known; occasional references to their behaviour are found in the very early flotation literature and in that of today. In general, however, nonmetallic minerals, valued at $2.00 to $15.00 per ton, have for a long time been regarded as cheap products and not worth much beneficiation. Consequently, only high-grade natural deposits suitable for direct mining and sale have been gouged out. Furthermore, the mining of these minerals has too frequently been in the hands of 'super-practical' men-men of no technical or other training, willing to work for a very low compensation. From the social standpoint, nonmetallics has been the field for small, untrained enterprisers with little money to spend on plant or equipment. But times have been changing. The impact of technically trained men on the old industry has revealed appalling losses and inefficien-cies and proved the value of processing materials discarded or avoided by the old regime.

Jan 1, 1937

By Yulin Zhou, WenFeng Li, Wen Chen

"In this article, with the help of the X-ray photoelectron Spectroscopy (XPS), a modern test method, all the characteristics of the chlorite,and adsorption collector A6 on the surface of chlorite have been studied. There exist abundant carboxylic C-O and C=O structures in the Carbon XPS atlas with strong adhesive ability after the reaction between new collector A6 and chlorite, which indicates that the ring structure and ether-base functional groups can strengthen the reaction between collector A6 molecule and chlorite surface. The results of XPS analysis indicate that the photoelectron spectroscopy peaks of Mg2p and Al2p moved towards low energy after collector A6 absorbed on chlorite surface, which indicates that chemical bonding through electron cloud transfer happened between collector A6 and Mg, Al ions of chlorite surface. The chemical reaction promoted the adsorption of A6 on chlorite surface and eventually improved the ability of A6 to float and collect chlorite.INTRODUCTIONThere are a large amount of iron-bearing silicate minerals such as chlorite in different types of gangue minerals in iron ore from different areas besides quartz (Yingyong et al, 2012; Qiang et al, 2009). There always exist Mg2+, Al3+ Fe3+ and other metallic ions due the isomorphic replacement among the irons of this kind of minerals. The dissolution often occurs on the surface of minerals with abundant metallic ions during grinding process, and some ions are exposed on the surface, such as Mg2+, Fe3+, Al3+, Si4+, which can increase the surface electrical behaviour of iron-bearing silicate minerals (Wanzhong & Chuanyao, 2002; Yuping et al., 2007), making it easy for the surface to react preferentially with the depressants such as causticizing starch which making it impossible for the surface to reach with conventional anionic fatty acid collector (Mowla et al, 2008). Thus, the beneficiation efficiency is dramatically decreased and the improvement of concentrate grade becomes very difficult. The conventional aliphatic acid collector has some defects such as poor selectivity, poor low temperature resistance, sensitive to water hardness, etc. Thus, the addition of synergist (Liu, & Yu, 2015) or other compound reagents (Zhou et al, 2015) can promote the adsorption of reagents to mineral surface, and improve the collecting capacity and selectivity of aliphatic acid collector to minerals. The addition of polar group to nonpolar group in aliphatic acid can improve the water solubility, dispensability and hard water resistance (Tian et al, 2013). The nitrogen atoms in amid ate aliphatic acid collector can adsorb on mineral surface by itself and supply coordinate electron which can form chelating keys to improve the collecting capacity of collector. There exist coordinate electron in oxygen atoms of ether acid collector, which, along with the oxygen on carboxyl compose chelate with metal (Luo et al, 2015). There are also exist some opinions that the ether acid can arrange into similar crown ether structure which can absorb on mineral surface. A new alicyclic unsaturated ether acid compounds collector A6 is adopted in this paper, the structural formula is listed in Figure 1. The A6 has a strong collecting ability to chlorite with strong water solubility and low temperature resistance."

Jan 1, 2016

By I. Kylmakorpi

In non-ferrous metal smelting, when the concentrate entering the furnace contains high levels of moisture, energy requirement for heating and drying increases and large volumes of exhaust are produced. To solve this problem, rotary dryers and flash dryers using direct heating, and also steam dryers using indirect heating have all been used for drying concentrate. The focus of this paper is to present the development and current applications of the Kumera Rotary steam dryer. The advantages of this technology are numerous, including reduced heating requirements, environmental friendliness, operation reliability and minimum maintenance needs; making it a top choice for drying concentrate.

Jan 1, 2008

By Etienne S. Bieler

Mr. Chairman, Ladies and Gentlemen, I come to you tonight distinctly as a physicist, not as a geologist or a mining man. My experience in applied geophysics has been short, and I do not doubt that many of you have a much larger acquaintance: with the subject than I have. A little over a year ago, the firm of Alderson, MacKay & Armstrong decided to investigate the possibility of developing a new method of electrical prospecting suitable to our northern Quebec and northern Ontario conditions, and asked me to take up the work. A preliminary survey of existing literature convinced me that the field of induction methods was most promising. I wish to give you some account of the work carried on last summer in the Rouyn district in this connection with the very able assistance of Mr. H. G. I. Watson. Geophysical methods of prospecting can be divided generally into four classes: magnetic, electrical, gravitational, and seismic. Each class depends on the existence of a definite property in which the valuable mineral to be discovered differs materially from the surrounding rocks. In the four classes, the property will be, respectively, magnetic permeability, electrical conductivity, density, and elasticity. By far the largest differences occur in the case of electrical conductivity, where it is not rare to find ratios of the order of several millions, or even billions, between ores, sulphide ores especially, and the surrounding rock. Hence the sensitiveness and delicacy of electrical methods. Of these four classes, only two, the electrical and the magnetic methods, have been put to extensive practical use in the discovery of metallic ores. The other two classes are important mainly in connection with oil detection.

Jan 1, 1928

By Nelson C. White

This paper summarizes the present state and future prospects of the potash industry, with special reference to its impact on production in Saskatchewan.

Jan 1, 1968

By Chen Feng

Compared to widespread successful deployment of robotic manipulators for repetitive and hazardous tasks in related industries such as manufacturing, the construction industry has achieved relatively limited benefits from robotics and soft automation. Unlike manufacturing, where robotic solutions benefit from the structured layout of the environment (e.g., factory assembly line), construction robots face unique challenges that arise from the rugged, dynamic, and unstructured environment of the work site, as well as the uncertainty and evolving sequence of occurring on-site events. This challenges any intended construction robots to not only replicate basic human motion, but also be capable of sensing and adapting to environmental changes, and making decisions based on the evolving state of the environment. Building upon recent advancements in robotic mapping, computer vision, and object recognition, the authors propose to introduce autonomous behavior at the basic task level for on-site construction robots to address these challenges in a flexible and extensible manner. This paper reports the outcome of the first phase of this research - a structured methodology for improved design and development of basic task automations - and focuses on algorithms developed for mobile robot navigation and relative pose estimation. The algorithms are implemented on a prototype mobile robotic platform, and evaluated in several experimental scenarios.

Aug 1, 2013

By J. Janzen

The cost to supply ventilation may exceed 40% of the total mine energy cost for underground mines and is often higher for deeper mines. The goal of Ventilation-on-Demand (VOD) is to ensure that the required quantity and quality of air is supplied to underground mining crews and diesel equipment at the least energy expenditure (minimum cost). A VOD system may include control of surface fans (Supply & Exhaust), underground booster fans, auxiliary fans and automated regulators/dampers to regulate the flow of air with more control elements providing more value. Strategically located Air monitoring stations measure air quantity and quality and provide feed-back enabling control. The modular design involving controls, intelligent instrument and intelligent motor control centres coupled with a communication network allows the quick installation, commissioning and expansion of the system as the mine develops. The result is a very robust, flexible system while reducing maintenance costs and spare parts. This paper discusses the impact of sensors, installation and commissioning on advanced controls and provides solutions for in-field applications.

Aug 1, 2013

By David A. Orava, Richard C. Swider

"The technical knowledge and practical experience accumulated by industry and others in abating acid mine drainage (AMD) is being proactively applied at every phase of the mine life cycle. This paper traces the mine life cycle from exploration to post closure monitoring and maintenance, and reviews AMD abatement measures that have become an integral component of exploration and mining activities.Attention is increasingly being given to evaluating AMD potential as part of exploration work, and studies related to project feasibility and design. Mining, mineral processing, and waste management options are selected taking into consideration their suitability to inhibit AMD. These inhibition measures are typically committed to in closure plans submit-ted at the permitting stage. Mines are operated and decommissioned, often progressively, as planned and in accordance with environ-mental protection policies."

Jan 1, 1996

By J. Y. Kim

This paper presents a novel action recognition method for observing human workers using interactions between actions and related objects on an internal construction site. This method can be used to measure work rates for labour productivity monitoring. This monitoring is critical because the performance of a construction project is significantly impacted by labour productivity. However, construction sites are generally crowded with a large number of workers and objects. Such congestion disrupts the accurate, automatic recognition of construction workers? actions. This congestion is one reason that existing automatic action recognition studies of construction areas mainly focus on workers? actions themselves. However, the crowded conditions mean that sites could offer a great deal of clues that could be used for automatic action recognition. According to psychological studies, interactions clearly take place between human actions and related objects, such as between hammering and a hammer. Humans use these interactions to recognize actions or objects more accurately. On the construction site, workers, materials, tools, and equipment are carefully planned out ahead of actual construction. The categories of workers and objects are pre-defined and, as noted, specific interactions define relations between worker actions and objects. In this paper, the interactions are limited to human workers and their hand-held objects. Action recognition results can be combined with hand-held object information to improve recognition accuracy. With the limited interactions, experiments in this paper show a significant improvement in action recognition. This paper describes the utilization of these interactions to improve construction action recognition accuracy based on human skeleton data and 2D color video from Microsoft KINECT sensor.

Aug 1, 2013

By A. Bezama

For over a decade European countries have addressed contaminated sites by developing technologies for managing both polluted soil and groundwater. This development has not only been driven by health and environmental aspects, but also because of economic pressures, as the remediation and redevelopment of derelict areas can be a meaningful alternative to undeveloped areas for the establishment of new industrial, recreational, housing and service locations. In most developing countries, however, the subject of contaminated sites is a new environmental issue that authorities have recently started to deal with. Among these countries, Chile has just started to prepare the country's legal context as well as to foster the formation of research and investigation groups that will deal with the exploration, investigation and management of contaminated sites. That requires a comprehensive technical, scientific and legal support in this stage. Goal of this article is to present the state-of-the-art technologies for site remediation currently applied in industrialized countries, in order to identify the most interesting approaches that can be implemented within the Chilean situation, especially considering the influence of the copper mining industry on the soil and groundwater quality of the environment surrounding their production facilities.

Jan 1, 2007

By A. Grimod

Rockfall drapery systems are commonly used as a simple, fast and cheap measure against the rock falling trajectories affecting very steep slopes. The system basically consists of a steel mesh, which is held on the top edge with a longitudinal cable fixed by means of a suitable number of anchors. The effect of this kind of intervention is to control the falls of the rocks, which are driven toward the bottom with slow velocity, or are stabilized on place. It can be used on any kind of slope to protect sensitive target in the mining industry, roads and railways, and inhabited areas. The falling blocks, typically smaller than 0.6 - 1.0 m in diameter, pile up into a trench (or into a ?pocket of mesh?) at the bottom. In comparison to other types of rockfall interventions, the simple drapery is cheaper, and its maintenance is easier, but on the other hand it cannot be considered the remedy for shallow instabilities, because it can only mitigate the effect of the falling trajectories. The design of simple draperies requires the analysis of several factors like the slope features (height, gradient, morphology), the geological and dynamic features (nature of the ground or rock, type of instability, erosion problem, blocks size), the environmental condition (presence of vegetation, aesthetical problem), the installation problem (accesses to the slope, safety for the workers, safety for the surrounding areas) and finally the performance required (temporary or permanent intervention, required maintenance, cost). Finally the most problematic design-step is the choice of the suitable mesh, the top longitudinal cable, and the top anchors type. Because of the highly variable nature of rockfall behaviour these structures cannot be standardized, but they have to be analyzed and designed for each case. Maccaferri has developed a new software application (MacRO 2) has a practical tool to define the mesh and the related supporting structure composed by up-slope cable and anchors. The software, based on the approach proposed by Muhunthan B. et al. (2005), allows designers to verify the top longitudinal cable, the anchors, and the mesh drapery, and to plan for maintenance procedures. Even if the method seems quite simple and rough, it is effective and lets the designer correctly foresee the materials and the geometrical features to be used on the interventions. This paper analyses the condition for the simple drapery installation, the main steps for the calculations, and it will present a case study in a U.S. mine. Nevertheless, even if the software allows a quick and simple calculation approach, onsite observations are always recommended in order to achieve a good design, with the ultimate goal of protecting property and human lives.

Aug 1, 2013

By Iina Vaajamo, Jani Jansson, Lauri Pesonen

In pyrometallurgical operations, structural integrity of a high temperature furnace plays a crucial role in the overall safety, profitability and ecological footprint of the plant. Furnace integrity is related to how reliable a furnace is and it can be compromised, for example, by having poor operating and maintenance practices, an inefficient cooling system and flaws in the overall furnace design. These flaws and poor practices might lead to unexpected shutdowns, production losses, increased emissions, or worse. This paper presents the main factors to consider when engineering a furnace and developing its operating practices, while ensuring safe and reliable operations without compromising process efficiency and quality of the final products. In this respect, Outotec’s solutions for the cooling system and for automation systems like PROSCON, Process Advisor, Sentinel and our Smelting Information Management System, are also introduced.

Jan 1, 2015

By Tony Szwilski

Using Unity 3D as a collaborative multi-user virtual on-line environment, an interactive virtual underground mine platform (IVUMP) is being developed to provide on-line access to mine safety preparedness training with a focus on mine emergency response exercises (MEREs). Communication and information flow among MERE participants and their actions can be monitored, recorded and evaluated. A mine ventilation simulation utility VFIRE is being incorporated to enhance the realism and interactive nature of the ?in-world? exercises as well as extend its functionality to include training in real-time ventilation and fire control.

Aug 1, 2013

By C. O. Swanson

THE purpose of this paper is to discuss the use of the dip needle in the field of mining geology. The subject matter is new only to the extent that it reflects the writer' s added experience in recent years. The treatment is brief, and those interested in a more extended analysis are referred to the articles listed at the end of the paper. In the discovery and tracing of mineral deposits, the clip needle, like most other geophysical instruments, can be used in two ways. One method may be termed direct; the other, indirect. The direct method is that of finding or following certain ore-bodies by virtue of their magnetic properties. Explicitly, or by inference, it is the method which many mining men and practising geophysicists have in mind when they consider whether or not a certain property should be studied by geophysical means. In the ideal case, this method demands little or no knowledge of geological conditions. The indirect method uses the clip needle as an aid to purely geological studies in working out the structure of a mineralized area. Although not as simple as the direct method, it enjoys a much wider field of usefulness. The writer's experience in the past fifteen years, which is believed to be typical, is that the indirect method finds application four or five times as often as the direct method. The indirect method is of particular value because it furnishes information concerning the relationship between geological structure and ore occurrence. Most mining engineers will agree that structural control is an important factor in the localization of ore deposits, and therefore that the subject under consideration is of some interest in mining geology. Specifically, then, the present purpose is to outline the principles and practice of using the clip needle in working? out geological structure.

Jan 1, 1941

By John L. Hatton

The author will introduce and describe the nature of Fiberglas-Reinforced Plastics. Successful applications of corrosion-resistant structures will be shown and described, including pipe, ducts, tanks and other equipment. These structures are generally designed to handle corrosive liquids and gases and have proved both satisfactory and economical in service in various industries in Canada. The specification of structures will be discussed in relation to materials, construction and workmanship, physical properties and methods of testing.

Jan 1, 1970

By O. Lashkari

Manipulation of pouring temperature is an efficient way to produce different microstructural features. In order to characterize the microstructure of rheocast billets due to different superheats of 615-695 °C, the parallel plate compression method was employed. Foundry 356 Al-Si alloy with different morphologies of primary a-Al particles were tested at different initial pressures of 4,8, 11,2 KPa, The resulted strain-time graphs were further treated mathematically to calculate viscosity of SSM billets. The interrelationships of viscosity, the microstructure and primary phase flow during compression are discussed, It is shown that the dendritic primary a-Al structure has the highest viscosity number which is almost three orders of magnitude greater than those for globular morphology, The current research have, for the first time, shown the validity and reliability of "parallel plate compression viscometry" method in characterizing microstructural evolution of Rheocast SSM billets.

Jan 1, 2005

By P. M. Shibley

"IntroductionMine drainage, surface. drainage and process liquors are the principal mine and mill effluents. The quantity and quality of these flows varies according to mineralogy, type and scale of mining, the process, tailing disposal, local ground conditions and climate.Typical contaminants remaining after solids sedimentation are colloidal or semi-colloidal particles, acids, alkalis, metals in solution, cyanides and thiosalts. Environmental regulations and guidelines have been issued in detail by the appropriate government agencies and will not be reviewed here. Revisions and additions are being made as our comprehension and abilities increase. Some contaminants of consequence have not been specifically regulated as practical treatment technology has not been identified. Thiosalts fall into that category as do the derivatives of the first stage of cyanide oxidation - cyanates.Most mining activities have present or foreseeable water treatment requirements. Because process economics can be adversely skewed by the environmental factor, the acknowledged objective of every operation must be to identify and anticipate those requirements.The evaluation and selection of water treatment techniques for mine-mill applications is complicated by the fact that most mine-mill effluents are high volume, dilute and chemically complex systems. Treatment processes applicable to most contaminants are: chemical or biological oxidation; neutralization and/or precipitation; liquid/solids separation. Other processes such as ion exchange, electro-deposition, foam fractionation, freeze crystallization and reverse osmosis offer the possibility of selective removal or concentration of contaminents. The latter tediniques, representing a slightly higher level of technology, are less suited to the large, low value flows usually encountered in the mine environment."

Jan 1, 1989

By D. W. Zandee

"IntroductionHaving mined an economic mineral bearing rock which is of insufficient grade to warrant direct smelting, upgrading or beneficiation is required to make it an economically viable ore. The first step in effecting the concentration process is comminution or sequential breaking of the rock to allow liberation and subsequent recovery of the desired mineral particles. Desirably the ore could be broken down to the point where the valuable mineral is completely liberated to maximize the chance of recovering as much of it and in as pure a form as possible. The number of energy intensive stages of breakage required to attain this goal depends on many physical characteristics of the ore such as hardness, friability, toughness, grain size, existing fracture planes and particle shapes.Commonly the distinct stages are primary, secondary and often tertiary crushing and finally grinding. To increase the efficiency of each stage of size reduction, pre-treatment sizing is common.Crusher feed is commonly scalped of large pieces or screened for reduction crushers and classified for secondary grindingcircuits.Although crushing and screening is employed for many different products, this chapter reviews current practice in larger tonnage metalliferous ore treatment plants.Current practice is to use large gyratory or jaw crushers for primary crushing and some sort of gyrating or cone crushers for additional stages of reduction. For autogenous or semiautogenous grinding circuits only the primary crushing stage is necessary, the balance of the work being performed in the grinding stage. For conventional grinding circuits using ball mills or combinations of rod and ball mills, secondary, tertiary and even quaternary crushing stages are normally required.Older type crushers such as stamp mills, double rolls, sledging mills and hammermills are no longer common but are used for small tonnage special processes.Important to efficient crushing are a variety of sizing devices such as grizzlies and vibrating screens. Products at different stages must be stored to give surge capacity and allow controlled feeding rates through mechanical and gravity feeders. These storage piles, bins and feeders as well as crushers and screens are commonly integrated into a total facility by means of conveyor systems. Most often these are endless rubber belts driven by simple or multiple drive mechanisms usually consisting of electric motors and speed reducers."

Jan 1, 1989

By J. C. Beidelman

One of the oldest settled portions of Canada is that "strip of land" extending into the Gulf of St. Lawrence, known as the Gaspe peninsula, with the Bay of Chaleur on its southern boundary. This "strip of land" is still so very sparcely populated that only at a few places does settlement extend more than a few miles from the coast. ? The peninsula is 160 miles long, 75 miles wide and with the exception of the above mentioned settlements is a mountainous wildness-void of all roads or inhabitants. Developments in the interior, of all nature, out-side of the cutting of timber by limit holders, was entirely lacking until the year 1915, when mining was first commenced. In the summer of 1844 Sir William Logan made a preliminary survey across the peninsula, from Cape Chat on the Gulf of St. Lawrence to Cascapedia on the Bay of Chaleur, passing through a country ?of which very little was known at that time. After a rather rough trip to the headwaters of the Grand Cascapedia river, Logan's party descended this river to its mouth, passing ten miles west of what is now known as the Federal mines. There is no record of Logan, or of any of his party, finding zinc or lead ores of any character on their journey across the peninsula, and until 1909 no precious or base metals were discovered within reasonable distance of Logan's survey.

Jan 1, 1924

By R. E. MacAfee

THERE have been great changes in the design, capacity, and pressure of steam generating units over the past fifty years. If we go back as far as 1890, the plants then existing were largely horizontal return tubular boilers, hand-fired, with the boilers supported on the brick sitting which was com-posed of red brick with, probably, a refractory lining one brick thick in the combustion chamber. About this time, the water tube boiler began to supplant the H.R.T. boiler and, where new plants were being constructed of any size, water tube boilers were largely installed. In those days, say from 1890 to 1905, a 250 h. p. water tube boiler was considered a large unit. These boilers were largely the straight tube type and were set with the first row of boiler tubes three to six feet above the grates. The brick setting was a combination of red brick and fire-brick. The fire-brick lining in the furnace proper was usually 9 in. thick and in the first pass 4 1/2 in., while the rest of the setting was entirely red brick. These units were largely hand-fired and were expected to produce about 100 per cent rating as a maximum. It may be well at this point to define rating, which is the evaporation of one boiler horse power per hour by each ten square feet of heating surface in the boiler. A boiler horse power is the evaporation of 34.5 pounds of steam from and at 212°F. Consequently, a boiler containing 2,000 square feet of heating surface is rated at 200 h. p. and the evaporation at 100 per cent rating is 200 X 34.5, which equals 6,900 pounds of steam per hour from and at 212°F.

Jan 1, 1939