Search Documents

By E. L. Martheleur

Introduction In October, 1945, the Coal Division of the Institute appointed a Committee on The Use of Electricity in Coal Mines, with the following terms of reference: ?To study under which conditions in each deposit the use of electricity can be brought closer to the coal face and which types of electrical machinery can be recommended?. It was not until the beginning of this year (1946) that the Committee had a chance to convene and .discuss the conclusions which are embodied in this report. Mr. McLeod, as Chief Electrician of the Dominion Coal Company, is intimately concerned with that Company's installations, and Mr. McIsaac, as Electrical Inspector of Coal Mines for Nova Scotia, is well acquainted with installations in all coal mines in the Province. The knowledge of both has been very valuable in helping to draft this report.

Jan 1, 1946

By L. H. Shang

The 319 Al-Si alloy is one of the most prominently used aluminium-based alloys in motor vehicle and engine applications, Microporosity present in 319 alloy castings reduces the load bearing capacity of the castings, The quantitative prediction of microporosity levels in Al-Si castings has been a subject of much interest for several years. In this research a new criteria function, tf 1,98 R13° (tf: local solidification time, R: cooling rate) was developed by multiple regression analyses, correlating thermal data from simulation studies to experimentally obtained microporosity values. This new criteria function gives a general prediction of microporosity in 319 Al-Si castings.

Jan 1, 2005

By Arthur Dubé

An account is given of the developments brought about in the last fifteen years by metallurgical research in the field of heat treatment of steels. The practical aspects of these developments are especially emphasized. Methods of representation of the phase-change during austenitizing and sub-critical transformation of austenite are described and the importance of time-temperature-transformation charts for the planning of heat treatment cycles is shown. Special copies such as retained austenite and internal stresses developed on quenching are also discussed in some detail. Due to the interest shown currently in these problems, it has been thought advisable to describe briefly the underlying principles and present some of the results already available.

Jan 1, 1945

By Michael E. Charles, Jaroslav J. Vocadlo

"The hydraulic transport of solids through pipelines can have many advantages over other modes of transport. Numerous successful applications both within plants and over longer distances have demonstrated the technical and economic feasibility of slurry pipelining. Solids successfully transported include kaolin, coal, iron ore, gilsonite and limestone, and others, such as sulphur and potash, are likely to be transported in Canada in the near future. However, though the technology of solids pipelining is quite advanced the underlying principles have not yet been formulated past the semi-empirical stage. The main objective of this paper is to present a discussion of the important technical and economic considerations in the design of so lids pipeline systems by reference to typical data. The Worthington slurry pumps and pilot facilities are briefly described."

Jan 1, 1972

By W. P. Campbell

Introduction OWING to the necessity of curtailing the length of this paper, nothing like an exhaustive treatment of the subject will be attempted. Instead, merely a few aspects will be considered, viz., water trouble in wells, sampling of waters, analysis, methods of reporting analysis, and the comparison of a few typical waters. The waters discussed will not be confined to those occurring in areas where oil or gas has already been found, but will include samples from areas in which drilling is being carried on in the hope that oil or gas may be found, i.e., from unproved fields. The Water Problem The problem of dealing with water encountered in oil and gas producing areas has engaged the attention of petroleum engineers from the early days of the industry. Water was not always considered a menace to oil sands; indeed, a certain amount of it was considered beneficial in some areas, but if such exist today they are very exceptional. In some fields, the problem is more acute than in others, and at times has baffled all attempts to solve it satisfactorily. Wells have been brought-in with promise of good production, but after a brief period have 'gone to water'. Whether ?it has always been a case of poor engineering in the form of unsuccessful water shut-off of 'top' or 'bottom' water, or because 'edge' water was present and water and oil were in such close contact it was impossible to remove the one without the other, is hard to say.

Jan 1, 1929

By C. S. Gibson

"MOST of the mines in the Province of Ontario in Canada are multi-level operations in steeply dipping veins; yet there is an appreciable number whose de-posits are relatively flat-lying, ranging up to 45° inclination.The veins vary in width up to several hundred feet and may or may not be branching systems. The depths of mines range from a few hundred to 8,000 feet, approximately. The primary products of the underground group are asbestos, gold, silver, cobalt, copper, nickel, iron, uranium, talc, fluorspar, gyp-sum and salt.There are a few open-pit mines. The majority are temporary in type because, as the outcrops are removed, mining is continued be-low surface. Primary products of the open pits are copper, nickel, iron, magnesium and nepheline syenite.The industry as a whole employs about 50,000 persons, approximately 60 per •cent of whom have dust-exposure occupations. The definition of a dust-exposure occupation and the requirements for •dealing with same are set forth in The Mining Act of Ontario.Results of extensive and continuing studies on the incidence and progression of silicosis have been reported periodically for years past, in annual reports of the Mines Accident Prevention Association of Ontario and in papers presented at Conferences sponsored by Mcintyre Research Foundation of Toronto, all of which have been published. The information provided therein proves the effectiveness of the means being used to prevent silicosis and allied disorders."

Jan 1, 1960

By Y. Wang

In this paper, the tribological and electrochemical corrosion properties of Al2O3/polymer nanocomposite coatings were studied using a micro-hardness test, a single-pass scratch test, an abrasive-wear test, and finally an electrochemical technique such as potentiodynamic polarization measurement, The coatings containing Al2O3 nanoparticles showed improvement in scratch and abrasive resistance compared with polymer coatings; this improvement is attributed to the dispersion hardening of Al2O3 nanoparticles in polymer coatings, Corrosion test results showed that the embedded Al2O3 nanoparticles in the polymer matrix do not sacrifice the corrosion resistance of the polymer itself.

Jan 1, 2005

By The Staff

"THE Wabana iron ore mines, owned and operated by the Dominion Steel and Coal Corporation, Limited, .are on Bell Island in Conception bay, on the east coast of Newfoundland. Mining began on surface in 1895 and, although open-pit work is still done on a small scale, the entire output may be considered to•be derived from extensive submarine workings. In 1958 the average daily production of hematite ore was close to 12,000 tons, almost all of which was concentrated in a heavy-media plant. SUMMARYThe character, occurrence, and extent of the submarine bedded deposits enabled early operators to meet prevailing market demands with the minimum attention paid to exploration. Mechanization of the mine and the pressure for sustained high tonnages since 1955 have emphasized the importance of an expanded exploration and development programme.A serious handicap has been the impossibility of utilizing normal diamond drilling methods to explore ore conditions in advance of mining faces. Drilling between tl1e bedded zones has been done but the major difficulty has been to delineate ore reserves in the lower bed, which has the greatest ore potential of the three mineable seams."

Jan 1, 1960

By W. Banda

"Trial application of air decks on a production shot improved fragmentation (32% reduction in x50). Empirical fragmentation models and digital image processing software were used to estimate fragment size distribution of the blasted muck pile. The x20, x50, and x80 passing fractions, and top size were 42, 265, 683, and 1,455 mm, respectively. Air-deck application reduced explosives load in blastholes, lowering total charging cost by US$20/hole (15% decrease) and the powder factor to an average of 0.86 kg/m3 (12% decrease). Blast results were 443,624 t of blasted material from the block (90% of total muck pile) was smaller than 900 mm.RÉSUMÉ L’application pilote de trous d’air dans le cadre du coup de mine effectué pour commencer la production a amélioré la fragmentation (une réduction de 32 % des x50). Des modèles empiriques de fragmentation et un logiciel de traitement numérique des images ont permis d’estimer la composition granulométrique des fragments du tas de déblais abattus. Les fractions de passé de crible de x20, x50, x80 et la dimension supérieure étaient représentées par des dimensions respectives de 42, 265, 683 et 1 455 mm. L’application de trous d’air a permis de diminuer la charge d’explosifs nécessaires dans les trous de mine, réduisant ainsi les coûts totaux de chargement de 20 $ US/trou (soit une réduction de 15 %) ainsi que le facteur de chargement (facteur poudre) à une moyenne de 0,86 kg/m3 (soit une réduction de 12 %). Les coups de mine ont résulté en 443 624 tonnes de matériaux abattus du bloc (soit 90 % du tas de remblais total) mesurant moins de 900 mm. INTRODUCTIONThe main objectives of production blasting are to achieve optimum rock fragmentation and to minimize overall production costs. Because blast fragmentation significantly affects the profitability of a mine, blasting is the first step of the size reduction in mining: An optimum size distribution is required to maximize the performance of mining and subsequent milling processes. If the fragmentation size distribution can be modelled and controlled, operations performance will improve. Blast fragmentation modelling is important in mineto- mill optimization: It allows the estimation of blast fragmentation distributions that can be modelled in downstream mining processes to determine the optimum blast design."

Jan 1, 2018

By T. E. Wakefield

"Final Galloway (stage) designs for vertical drill and blast shaft sinking projects evolve from complex thought patterns which integrate operational processes, systems and methods of communication, power supply, drilling, blasting, ventilating, mucking, supporting, surveying, dewatering, sealing, concrete lining and shaft furnishing. Attention to ergonomic design detail at the shaftsman / structure interface is at the heart of safe and successful multi-deck working platforms. For economy the end product must have a low mass to reduce suspension rope end loads to be able to use smaller suspension hoists and have lighter headframe structures, be robust to withstand concussion damage, be easily constructible on site, be maintainable in the shaft barrel, and comply with safety and legislated standards. This paper’s ambition is to describe a systematic design framework and sequenced thought process that delivers a product that is engineered with excellence, illustrated by making use of two designs that evolved during recent Galloway projects, one destined for a large diameter man/material shaft, the other for a ventilation shaft. The stage engineering iterative process starts with mapping permanent and sinking hoisting layouts, followed by laying out horizontal deck plans, mostly constrained by the permanent shaft purpose and configuration, whilst maximizing openings to enable muck to be removed rapidly for the best sinking cycles. Concurrently the designer needs to understand the chosen sinking methodologies in conjunction with crewing to determine the number of decks and fix their spacing. Insufficient access to move and line up formwork, set reinforcing rods and pour concrete in the confined spaces of the stage is an inherent major risk to be mitigated. An iterative and integrative process follows for the primary configuration which delves into increasing design detail, accommodating all other methodology influences, resulting in 3D layouts for further risk assessment, review and fine tuning by seasoned shaftsmen. INTRODUCTION Documented colliery shaft sinking practice from the late 1800’s makes reference to purpose built walling (bricked lining) cribs with floors suspended in sinking shafts, thereby allowing shaft lining to proceed concurrently with the excavation. Improvements were made by Sir William Galloway who introduced two decks supported at the corners by angle irons. The sinking stage, or Galloway, has developed substantially over time to be the in-barrel heart of the sinking operation, with overwhelming complexity for those who have to design one for the first time."

Jan 1, 2019

By G. G. Eichholz

SUMMARY RADIOACTIVE dynamite has been prepared by introducing a small amount of antimony-124 into the explosive. Test work is described on the effectiveness of this tracer, on radiation levels in its neighbourhood, and on different methods of .application. Factors determining the choice of isotope, amount of activity, and overall cost of this process are discussed. INTRODUCTION Instances are known in which dynamite remains unexploded in drill holes in mining operations. Usually such 'bootlegs' are easily located by inspection of the face and the powder is removed before subsequent drilling is started. Occasionally, however, serious accidents occur because workmen drill into an undetected piece of dynamite. In order to avoid such accidents it was suggested that a different method of location might be tied, such as that afforded by the use of radioactive tracers. This paper describes some experiments that were carried out under the auspices of the Department of Mines and Technical Surveys, with the active co-operation of Canadian Industries Ltd. and Canadian Refractories Ltd., to test the feasibility of such a scheme.

Jan 1, 1957

By H. J. McQueen

The irregular history of Mg wrought products is briefly described. The temperature and strain rate dependence of microstructural evolution, flow stress and ductility of Mg alloys in hot working, are described. The flow curves rose rapidly to a peak stress which was lower as temperature T rose and strain rate e declined and above 300°C the curves extended into plateaus until failure. Clearly grains not oriented for slip undergo mechanical twinning in the initial stages (a 0.15) at all temperatures. Basal slip proceeds in suitable grains and in the twins. The stress concentrations at grain and twin boundaries lead to slip on non-basal systems and to the formation of subgrains with greater dynamic recovery (DRV) at higher T or lower e. With increasing strain, misorientation builds up resulting in dynamic recrystallization (DRX) first at twin intersections and later at grain boundaries which have become quite serrated. Even after extensive straining at high temperatures, the new grains are found mainly along the boundaries of the original grains, leaving their centers with only basal slip except when nucleation at twins leads to completion of DRX throughout a grain. Despite similar shear modulus and melting point to Al, hot mechanical forming behavior of Mg alloys differ due to differences in crystal slip systems, twinning, and second phases. Moreover, the influences on forming of alloy additions (solutes, segregation in casting, dispersoids, precipitation) and impurities are not as well catalogued as for Al. Despite the benefits from dynamic recrystallization, varied grain orientation effects, heterogeneous substructures and the resulting stress concentrations result in considerably lower ductility for Mg alloys at the same stress level as for Al materials. Application of these theories to extrusion, rolling and forging and the effects on product properties are surveyed.

Jan 1, 2006

By E. C. Keeley

THE property of Buffalo Ankerite Gold Mines, Limited, is in Delora township, Porcupine area, Ontario. The southwestern part of the property is ground formerly owned by Marbuan Gold Mines, Limited, which was acquired by Buffalo Ankerite in January, 1936. Until 1938, the Ankerite (or North) mine and the Marbuan (or South) mine continued as separate operations, each developed through a surface shaft and winze to the 1050 level and each having its own mill. This meant high hoisting costs, which, in 1936 and 1937, amounted to 36 cents per ton. In 1938, the underground workings of the two mines were connected on the 1050 level, and ore from both mines was hoisted at the main, or No. 2, shaft of the North mine, location of which is shown in Figure l. This shaft was discontinued at a depth of 1150 feet because, owing to the soft nature of the talc (serpentine) rock in which it was sunk, it had to be concreted throughout, and also because of its great distance--1,100 feet and 1,400 feet, respectively-from the North and South orebodies.

Jan 1, 1945

By M. Laframboise, M. Buarzaiga

High-pressure acid leaching (HPAL) of nickel laterites has received considerable attention in recent years. High paymetals extraction, good selectivity, and advances in pressure hydrometallurgical technology are some of the reasons for this interest. Falconbridge Limited (Sudbury. Ontario) investigated the HPAL process using both fresh water and seawater for ore processing. The use of seawater resulted in a chloride concentration of 7.8 g/L in the autoclave feed. A test program was developed to study the effect of process water and leach temperature on the leaching behaviour of different ore compositions from the Koniambo deposit in New Caledonia. The work showed that salinity has a major effect on autoclave chemistry. This paper explores the results.

Jan 1, 2004

By M. W. Grabinsky, P. B. Tomory, J. Carvalho, J. H. Curran

Many underground mining operations use Split Set friction stabilizer bolts for rock support. Currently, however, little has been done to quantify the effects of various rock mechanics and operational parameters on the capacity of frictional support systems. The strength of Split Sets is usually measured by means of a pull test wherein a jacking force is applied to the bolt and a slip load is obtained. In order to evolve a rational design procedure for this type of support, an extensive database of over 900 pull test results from more than 50 mines through- out North America has been assembled and analyzed. Associated relevant rock mechanics parameters (rock type and quality) and operational details (drilling method, bit size, drive time, time to pull test) were also obtained, as completely as possible, for each test. Analysis of the information has yielded several charts that relate pull-out strength to relevant parameters and simple statistical analyses were conducted where necessary. Quantified distributions for pull-out strength were also produced for several operating conditions. The factors that most significantly affect bolt strength have been identified and specific applications to design are discussed. The information presented will assist mining engineers in designing safer and more economic support using Split Sets.

Jan 1, 1998

By J. H. C. Scrimgeour, T. Toong, R. E. Hamilton

"The principles involved in the use and application of mathematical models as an aid to the development of advanced process control computer systems are described briefly. This is followed by a brief survey of known models of this kind for the simulation of mining industry processes.The main part of the paper describes a dynamic model of the flotation process developed by Canadian General Electric. Using flotation rate constants for each species of mineral and gangue, the model provides a numerical solution of the differential equations describing cell behaviour. The cell mode] is used repeatedly as a subroutine in the •over-all-plant model. The features of the cell and plant models are described.Simulation runs from the plant model show stream .assays and other indications of plant behaviour printed typically in 1-to 10-minute steps for several hours of •Operation following typical disturbances such as changes in feed rate or reagent addition rate. The simulation can :Show expected behaviour for both uncontrolled and computer-controlled plants."

Jan 1, 1970

By Craig Ford

Inmet Mining is committed to implementing the highest corporate responsibility standards in its mining operations worldwide. Inmet is 100% owner of Minera Panama, a world-class copper project that is currently in the feasibility phase in north-central Panama. Panama has limited experience with modern mining, limited mining capacity, and the project context involves significant social, environmental and political complexity. The Project area is remote with recent in-migration of latino and indigenous people, informal and small-scale mining, local subsistence populations and considerable biodiversity value, coupled with a complex jurisdictional setting. In short, it is increasingly the kind of project mining companies are taking on because the easy projects have already been developed. With such challenging conditions, anticipating and managing social risks is critical to effective project management. To this end, between August 2007 and the third quarter of 2009 Inmet seconded Monkey Forest Consulting Ltd to the project to assist Minera Panama in building and implementing an effective, early phase external relations strategy. The team was also tasked to find and develop a locally based team that could sustain success through project development and into operations. Today?s presentation was created by Inmet and Monkey Forest and describes some of the lessons learned in implementing an effective early phase process for managing social issues.

May 1, 2010

By Greg M. Hollyer

The search for minerals in the future will be dominated by deeper exploration and the need to accurately target ?blind? deposits as more and more of the ?easy? near surface targets are exhausted. In this context, key technologies are emerging for deep exploration both in grassroots and minesite exploration, including the Titan 24 Deep Penetrating geophysical technology. Introduced in 2001, this technology has grown rapidly into an accepted approach for exploration in a variety of geologic environments, including brownfield environments where discovering additional reserves would most quickly benefit companies. Titan 24 belongs to a new class of sophisticated Distributed Acquisition Systems (DAS) which record high-volume, high-quality data simultaneously at multiple receiver stations. This data is then processed digitally, modeled using specialized inverse modeling software, and interpreted according to geologic and other parameters. The result is a robust, high-quality, high-volume data sets which provide a basis for improved imaging to depth. In this paper, the Titan 24 distributed technology is discussed. Illustrations of the vast improvement to overall exploration are showcased through results in several case studies. These include examples from two gold deposits, a porphyry deposit and a minesite. These examples show the range of applicability of the technology and the ability to effectively image mineralization, lithology, structure and alteration to depth as an aid to understanding prospective mineral deposits and targeting drills more accurately.

May 1, 2008

By A. Koning, P. Lauzon

Pressure hydrometallurgy operations require vessels to be lined with an impermeable membrane for corrosion protection and one or more courses of refractory or ceramic brick. Examples of unit operations that utilize composite lining systems include pressure oxidation autoclaves, sulphide precipitation autoclaves, chloride leach reactors, flash vessels, cyclone separators, and direct contact condensers (heater vessels and quench vessels). The refractory lining must satisfy multiple requirements: it must thermally insulate the membrane from process fluid, be structurally stable, provide erosion resistance, be chemically compatible with process fluid, and provide an economic service life. New hydrometallurgical processes are pushing the pressure, and temperature, with each new generation of plants. A fundamental understanding of all factors affecting the mechanical stability of the lining system is essential as lining designs move further away from the industry's experience base. The impact of irreversible chemical swell, operating factors, design factors, and installation factors are presented based on modifications to the traditional one-dimensional mechanical stress model. A new stability criterion - that the brick lining remain in contact with the steel shell membrane - is presented. This new stability criterion imposes new restrictions on the lining design.The effect of geometry and adding additional degrees of freedom to the analysis is explored using two-dimensional and three-dimensional Finite Element Analysis (FEA). The effect of these additional degrees of freedom on the results of the one-dimensional model are discussed.

Jan 1, 2004

By K. Nagai

The Asian projects are now in their second terms after the five-year first terms. Ultrafined-grained steels were developed in lab-scale and/or in practical process. Basic approach has been performed to explore the evolution mechanisms of ultrafine-grained microstructures. There have been investigated two approaches to make the ultrafine grains: the "recrystallization route" and the transformation route. In the "recrystallization" route, heavy deformation at low temperature is necessary for the ultra-refinement. In the transformation route, making the high density of ferrite initiation sites in the deformed austenite, especially of the heavily compressed austenite structures, is essential for the ultra-refinement, and further hindering the ferrite growth is also inevitable to utilize the high initiation rate. Strength and toughness are dramatically improved by the ultra-refinement. Fatigue property is also excellent. The poor uniform elongation can be enhanced by the design of the second phase dispersion. At the same time the application has been also pursued from various viewpoints of engineering to take advantages of the ultrafine-grained steels. Bridge, ship, construction, automobile and other high strength parts are being attempted for the application.

Jan 1, 2004