Search Documents

By Harold Margolin

The Ti-Al system certainly merits the investigative attention it has been receiving and this latest contribution by Blackburn is therefore to be welcomed. The titanium-rich end of the phase diagram shown here, as well as the diagram by crossley,17 Clark et a1.,18 and Tsujimoto and Adachi,29 reveal no other intermediate phase than Ti3A1, although a previous work by Ence and Margolin20 had reported an additional intermediate phase. Since then, Buerger Precession pictures of single crystals of 10.5, 11.5, and 12.5 wt pct A1 were made at New York university21 and the extinctions were found to be typical of a D6h a Ti structure. Some superlat-tice spots and/or streaks suggesting the presence of an Mg3Cd structure, i.e., Ti3Al, were also found. Since these specimens had been quenched from the y region20 and had revealed a Ti, it was concludedz1 that y does not exist and the structures interpreted as m + y could not be so considered. The absence of normal two-phase behavior in these structures had been indicated in the paper. Accordingly, the two-phase region y + 6 becomes a + Ti3Al and there is some agreement between the results of Blackburn and of Ence and Margolin20 as to both shape and existence above 900°C of an a + Ti3Al field. Crossley 17 proposed that Ti3Al is a line compound which decomposes congruently at 900°C. It is difficult to discount entirely the fact that clear two-phase structures, varying in amount with position in the two-phase field, could be detected above 900°C by Ence and Margolin.20 Precipitation during quenching could not have been so regular and the twin-phase syndrome17 does not apply. The heat treatment and quenching technique was essentially the same as was used by Crossley, whereas Blackburn, who used a rapid quenching procedure, also showed a two-phase a + Ti3A1 field above 900°C. If the two-phase field exists above 900° C, it is easy to picture a two-phase field which could account for the data of Crossley below 900°C without invoking a line compound existence of Ti3A1. All that would be necessary would be an 0 + Ti3Al/Ti3Al boundary which curved sharply to higher aluminum contents below 900° C. It is clear that the controversy must be solved by techniques which obtain data at elevated temperatures without quenching. It is conceivable that the difference in width of the a + Ti3N fields reported by Blackburn and by Ence and Margolin is due to the longer annealing times used by the latter investigators. The criterion for establishment of equilibrium in our work20 was the

Jan 1, 1969

By Willard C. Lacy

Rather than attempting to present a summary of the many and highly varied papers that have been presented at this symposium on sampling and grade control, I will attempt to extract the general philosophy of analysis and approach, and attempt to identify the trend of future developments. First, the term "sampling" is used with its broadest connotations. A sample consists of a representative portion of a larger mass, and must represent the mass not only in the grade of contained metals or minerals, but also in all other respects in terms of mineralogy and mineral quality (1, 5), deleterious materials, recoverability of economic components, physical behavior, geophysical response (I), and even archaeological and environmental aspects (7, 11). The sample must be taken from a locality and in such a manner and quantity that it is representative of the larger rock mass. This calls for complete and accurate geological control and an understanding of the nature and distribution of the contained chemical and physical elements and a record of the effectiveness of the different sampling methods. Second, value of a given mass of ore material is based upon its profitability - the difference between recoverable value and costs to achieve recovery, beneficiation and sale. There is a strong movement in mining geology control toward more complete analysis in determining cutoff grades and in grade control, as illustrated by the kriging of metallurgical recovery factors as well as grade at the Mercur Mine (8). To achieve a "profit- ability factor" as a guide for economic mining practice requires further integration of: 1) the value of contained metal or mineral, 2) percentage recovery of values, 3) dilution of ore with waste rock, 4) addition to, or loss of value as a consequence of by-product materials or deleterious components, 5) cost of producing a saleable product plus mini- mum profit to justify the effort (cutoff), and 6) cost of land restoration (7, 11). All these parameters vary with the rock type, rock structure, mineralogy, depth, geometry, mining and metallurgical methods, but they must be sampled and analyzed if sampling and grade control are to reflect profitability. A wide variety of deposits has been presented at this symposium; each deposit with its own problems and special solutions. Deposits containing high unit-value components, e.g. precious metals and diamonds, present special problems in the obtaining of accurate samples and generally require statistical analysis control methods or may disregard or modify occasional high or occasional low values, based upon experience (12 ) Grade control may be accurate for the long term but may vary for the short term. Bulk sampling is always essential. Deposits containing metals or minerals with low unit value are very sensitive to transport costs, and they are often very sensitive to small amounts of deleterious components or differences in physical or chemical behavior. Problems of sampling and grade control change with the genetic type of deposit, with the stage of deposit development and with the size of the information base. Precious metal epithermal deposits (2, 6, 8), because of rapid vertical zonation and erratic lateral distribution of values, have always been difficult to evaluate and maintain grade control and ore reserves. On the other hand, evaluation and grade control are relatively easy in bulk-low- grade deposits (4, 13). However, these deposits generally have a low margin of profit and are sensitive to mining and beneficiaton costs, price fluctuations and political costs. Industrial mineral deposits (5) often must be evaluated on the basis of their behavior, rather than by chemical analysis. Environmental impact generally increases with the scale of the operation, but certain elements or minerals have especially high impact effects (7, 11). In the exploration phase there is no production control of sampling procedures and careful geological observations are particularly essential. The greatest number of problems is related to the oxidized outcrop where the chemical environment of the ore body has changed and the contained values may have been enriched, depleted or values left unchanged (2, 6). Present evidence suggests that gold values may be very mobile under certain conditions (2, 6) and stable under others. Everything must be sampled in detail. Principal values and by-product or deleterious elements may vary dependent upon their position within the soil profile. Such factors as geomorphic position, erosion rate, vegetation, climate, etc., may affect the interpretation (1, 3). During the development phase it is equally easy to overtest, to have "paralysis by analysis," as to undertest (3, 6). Bulk samplng and testing are

Jan 1, 1985

By H. W. Gillett

Unlike most previous Howe lecturers, I had not the good fortune to be associated with Henry Marion Howe, nor to be directly one of his students. Yet, through his writings, he has been my teacher, as he has of all American metallurgists. Instructive as his writings are—I use the present tense because Howe thought so keenly and reasoned so surely, seeing clearly, as if by intuition, what was hazy to lesser minds, that his writings are still vital—it is not those books and papers, nor even the minds he trained in his classes, that were his most outstanding service. It was the spirit of Howe in his approach to the problems of metallurgy, his broad-mindedness and fairness, his recognition of the need for theories and hypotheses to explain metallurgical phenomena, his willingness to use them as servants, as well as his questioning attitude—his refusal to accept them as masters—that comprise his greatest service. This most thoroughly warrants the honor the Institute pays each year to his memory. These traits I so respect and honor in any man that I glory in this opportunity to do reverence to him in whom they were so notably united. Howe's Discussion of a Creep Problem I have often wished that Howe were still with us to turn his keen insight upon the problems of the use of metals at high temperatures, a field much studied but still very hazy. Indeed, 53 years ago, in a paper1 before this Institute, Howe stated a problem closely allied to some that still perplex metallurgists and engineers dealing with the high-temperature field. Howe was intrigued by a report2 from another old master, Robert Henry Thurston, on the behavior of annealed vs. cold-drawn iron wire, and in order to broaden the foundation for metallurgical generalization, Howe made experiments of his own on copper and silver. In these tests by Thurston and by Howe, the wires were rapidly loaded to determine the

Jan 1, 1939

By AIME AIME

DESTRUCTION of the plants, machines, utilities, tools, materials, and other essentials for peacetime living penalizes not only the owners of the materials destroyed, but the world as a whole. Specifically, the fundamental fallacy of any proposal for the in- discriminate destruction of the German industrial system is that it fails to differentiate between the wartime and the peacetime economy of the Reich. We are for one simple, clear objective-an effective industrial means to keep Germany from starting another war. This objective should not be con- fused, especially before the war is even won, with the appropriate punishment of Germany or with the international arrangements for the long future to be made around the peace table by the representatives of the Allied Nations after victory is achieved. This paper, therefore, does not deal with broad, complex postwar questions of diplomacy and international policy. "Unconditional surrender" implies disarmament of the German armies, the surrender of all arms, munitions, air- planes, and other ordnance material in stock piles or in process. It also should include the elimination of all German war production facilities, such as ordnance plants, munitions plants, and submarine works, and the control of raw materials required by war industries.

Jan 1, 1944

By J. J. Lillie

Sublevel stoping was first developed in the Michigan iron mines many years ago. Since that time this method, and modifications with long hole drilling, have been used in a number of non-ferrous mines and have been described in various papers and articles. With a few exceptions, the operations where sublevel methods have been applied are producers of large daily tonnages from ore bodies of considerable size. In selecting mining methods for small properties or relatively small detached ore bodies, sublevel methods often have been overlooked. The method has been used success- fully in relatively small operations at Copper Canyon, Nevada, and, more recently, in mining small ore bodies at Darwin, Calif. As a result of this experience, we believe that a review of the general procedure, the advantages noted, and the results obtained will be of interest to many operators of relatively small mines.

Jan 1, 1949

By Nathan C. Rockwood

BASIC mineral commodities may be divided into two general classifications in their market or price characteristics. In one class are commodities sold on a world-wide basis, as gold, silver, nickel, asbestos and petroleum, and in the second are those produced and sold locally. Of course, no precise line of demarcation exists between the two; coal, for instance, belongs more or less in both. If there are enough producers of any commodity to prevent control of production by any one person or group, a free market then exists and the price in a buyer's market is determined by the most favored producer-meaning the producer, with the lowest production cost or the lowest cost of transportation, or both, to the particular market, or place of use. With minerals in the first classification, their high intrinsic value far outweighs the transportation cost and a uniform market price is accepted as an essential element in the economy of distribution. But with common minerals of small. intrinsic value and relatively high transportation costs, economists are reluctant to admit that a uniform price may also be an essential element in distribution.

Jan 1, 1940

By Thomas T. Read

EVERYONE engaged in the teaching of mining engineering will, I suppose, agree that the most difficult subject to teach is "Mining Methods." One primary difficulty is that the students taking the course have either had no previous experience in mining, or else they have had; either seeming to be somewhat of a drawback. The students who are unfamiliar with mines find it difficult to visualize underground conditions, as described and illustrated with sketches and maps, while those who have had underground experience seem to 'find it difficult to visualize anything much different from that which they have already seen. This reminds one of the remark about the Presbyterian doctrine of predestination, to the effect that "you are damned ,if you do; and damned if you don't."

Jan 1, 1930

By K. Reinhardt

THE idea of burning blast-furnace gases directly in gas-engines, instead of under steam-boilers, as had previously been done, was first put into practice barely ten years ago, almost simultaneously in Great Britain, Germany and Belgium. The pioneers of this movement made their first experiments with small engines. After these experiments had given satisfactory results, and it had been shown that the thermal value of the poor blast-furnace gases, in spite of defective scrubbing, could with safety be directly transformed into mechanical work in the gas-engine, there very soon arose a considerable demand for gas-engines of large power, similar to the large steam-engines employed in metallurgical works. In face of these sudden requirements, the gas-engine builders were placed in a difficult position; for up to that time the gas-motor was considered as suitable for small engines only, and it was generally believed that the limit of size bad been attained with 100 to 150 effective h.p. in a single cylinder. Manufacturers of gas-motors, however, did not underrate the advantages offered by this new field for their manufactures, and it so happened that in Germany the Berlin-Anhaltische Maschinenbau-Gesellschaft, of Dessau, was the first to undertake the construction of a 600-h.p. two-cycle gas-engine, with two cyl¬inders of the Oechelhäuser-Junkers type, for the Hoerder Mining & Smelting Company. The engine was started in 1898, and, with a few improvements and alterations, is still working satisfactorily. This engine worked with astonishingly high of efficiency, considering the period. The builders were therefore

Nov 1, 1906

By Elmer A. Jones

Development work in mines of St. Joseph Lead Co., Southeast Missouri, using trackless loading equipment shows definite advantages: Speed of cleaning, ability to work on steep grades and sharp crosscuts, good later tracking conditions, and possibility of wasting rock in old abandoned stopes.

Jan 1, 1950

By James K. Richardson

Today, the enigma of the "missing man" in the metal mining industry equals, and frequently surpasses in objective importance, the problems of ore development, drilling, sampling, pumping, milling techniques, geophysical prospecting, or any one of a hundred highly technical subjects. Unfortunately, as engineers, we have confined our attentions, in the main, to the scientific phases of mineral technology, relegating our man power problems to the background. But what good has all our scientific study and preparation been if we can't get the ore mined, milled, or smelted? What has happened to our labor supply? Where is the good old miner who could timber, drill a round, lay track, or do any job underground?

Jan 1, 1949

Jan 1, 1884

By Augustus Locke

WHY should I, a geologist, be coming before you to talk about finding ore? Certainly, the great discoveries of the past have not been made by geologists, but by men of very different tastes and training. If, in the year 1800, the course of ore discovery could have been foreseen, there would have been no reason to put it into the hands of geologists or other men of technical preparation. It was not geologists but explorers, Indian fighters, prospectors, manual laborers, and hardy financiers, who initiated the American mining industry. Then why this association of geological technique with ore finding? Why this feeling that the way to find ore is to apply to the problem what we call geo- logical principles? Well, to put it broadly, the old method has run out on us. It no longer works. Or, to put it another way, the cost of finding ore by the old method has mounted so high that one old district after another has become, practically speaking, dead, and various other old districts that are still going apparently at full strength are actually beginning to limp, and, with the cost of discovery mounting yearly, to fear, more than they will acknowledge, that the end is approaching.

Jan 1, 1926

By FLOYD T. TAYLOR

IN 1833, less than one hundred years ago, Michael Faraday discovered and stated the laws of electrolysis. His discovery formed the foundation of a new use of metals which has now reached a variety of application not ordinarily appreciated. Furthermore, things can be done with electro-deposited coatings which have thus far defied other methods. Some of the uses of electro-deposited coatings are interesting. The tonnage of metals already finding an outlet through such a channel is considerable. In general electro-deposits have two characteristics: ornament plus utility; utility plus ornament. Both these factors are usually found associated in electro- deposits. Ornament plus utility was probably the first use. For example, the silver-plating of tableware, having its real birth in Birmingham, England, about 1844. However, this same ornament plus utility retarded the development of electro-plating, because in the beginning, electro-plated articles were branded with the odium of imitation and shunned accordingly. The gold brick of the swindler may be an exception to this statement.

Jan 1, 1929

By Thomas T., Read

IT does not seem practicable to review all the other specialized curricula that have developed in the mineral industries field in so much detail as has been given for petroleum. Nor is it easy to draw a definite line between true curricula, leading to a designated degree in the special subject, and options, which may range from the mere substitution of one or two courses for others ' in the final years to differences so extensive as almost to amount to separate curricula. Even to attempt to catalogue all the options that have been offered at one time or another would , require too much space. The remainder of this discussion, there- fore, will be confined to three topics which seem to be of major importance. Mining and metallurgical curricula will be covered in a later chapter. Geology The first, from the historical view, is geology in its relation to the mineral industries. Previous, chapters have made clear that in the early years of mineral industry instruction in the United States economic geology and mining engineering, so overlapped one another that men who were by training and experience economic geologists were appointed professors of mining, while men who had graduated as mining engineers sometimes developed into professors of geology. Even today men whose basic training was in- geology as a pure science, and who perhaps took a doctor's .degree in that subject, have attained such distinction in the mineral industries as to be universally accepted as "mining men," and their right to be regarded as mining engineers would not be questioned, even though 'they did not .take a degree in engineering. Nevertheless the distinction does exist, and has been made a concrete reality in recent years by the enactment of

Jan 1, 1941

By T. W. Turk, S. A. Sass

The engineering design features of the Mercur Gold Project crushing, grinding, carbon-in-leach, bullion, reagent, and tailings disposal areas will be discussed in this paper. It presents a project overview and flowsheet along with selected design alternatives. During the engineering phase, major equipment and other features were selected to optimize design within site location and environmental constraints. The project team organization and procedures were adopted to accommodate multiple optimization studies while maintaining a tight engineering schedule.

Jan 1, 1985

By A. P., Svenningsen

ECONOMICAL handling of a minimum of 25,000 tons of minus 3/4-in. ore per day, grinding it to 2 per cent on 65 mesh, and effecting a high recovery of the copper at the lowest possible cost were the principal aims in the design of the new Morenci concentrating plant. Dealing with a tonnage of this magnitude, it is obvious that lost motion cannot be tolerated. When ore is carried on a conveyor an unnecessarily long distance or elevated to a greater height than necessary, or when pulp flows in a launder by a circuitous route thereby losing elevation and distance, we have lost motion which is always costly both from the standpoint of construction and operation. In addition to the 25,000 tons of ore which must be handled, 100,000 tons of water per day has to be carried through the plant in the treatment of the ore. Though water is not so difficult to handle as the ore, the combined tonnage represents a figure which could easily run into a considerable monetary loss per day if all phases of the design were not carefully followed with the idea of eliminating any unnessary handing of materials.

Jan 1, 1942

By AIME AIME

UNDER the auspices of the Institute's Committee on Industrial Preparedness, a symposium was arranged for the Annual Meeting on the subject "Ores, Metals, and the War," with many well-known Government men and industrialists participating. Wilfred Sykes, president of the Inland Steel Co., of Chicago, presided, with C. K. Leith and Clyde Williams as vice-chairmen, Mr. Williams presiding over the latter part of the meeting. On the Auditorium stage in the Engineering Societies Building was a formidable corps of "experts," with an audience of several hundred to hear what they had to say and to ask questions.

Jan 1, 1942

By R. Gilman Brown

INTRODUCTION. MINES are interesting by reason of what they have done for man, or of what has been done for them by nature. Not all are interesting on both scores. Many profitable mines are commonplace to the geologist; and many presenting unique geological conditions have been sad failures commercially. The Standard group at Bodie has produced in 25 years, $14,500,000, paying $5,000,000 in dividends.' On the other hand, this output has been mined (almost wholly above the 1,000-ft. level) from a system of more than 100 veins, ranging in thickness-from 0.5 in. of "specimen rock" to 30 ft. of clay and quartz; distributed through a zone about 2,000" ft. in width, and representing from three to five distinct periods of formation. This group, therefore, by reason of its industrial record as well as its geological features, may fairly be regarded as doubly interesting. The Bodie district occupies an island of recent (Tertiary) hornblende-andesite, surrounded by a complex of igneous rocks and breccias. It lies at the summit of the eastern foot-hills of the Sierra Nevada mountains, and within the Great Basin, a few miles from its western edge, marked here by Mono lake on the line of the Great Fault. The average elevation of the outcroppings of the veins may be taken at about 5,700 ft. The andesite projects from south to north in a great tongue, 12,000 ft. long and 5,000 ft. wide, reaching an extreme height at the northern end of perhaps 1,000 ft. above the adjoining small canyons. These separate it from the main mass of the foot-hill

Jul 1, 1907

By G. Caetani

I. INTRODUCTION. WE owe to the courtesy of Mr. R. M. Raymond, Manager of the El Oro Mining & Railway Co., Ltd., the permission of publishing in this paper the results of a series of experiments and tests made in view of determining the economical limit to which the fine grinding of the ore by tube-mills could be carried on. For the sake of clearness, the following definitions are given of certain terms used in this paper, as well as of the units and screens in the experiments. Slime : In a general way " slime" is that mill-product, of which from 90 to 95 per cent, will pass a 200-mesh screen (0.067 mm. aperture), and which is treated as one class of material in the El Oro cyanide-plants. As a screen-product, slime constitutes all material that *ill pass a 200-mesh, screen. In sizing, the following products are distinguished:- Coarse Sand : That material remaining on a 100-mesh (0.111 mm. aperture) screen. Fine Sand : That passing through. 100-mesh and remaining on a 200-mesh (0.067 mm. aperture) screen. Slime: That passing through 200-mesh. Fines, which pass through 200-mesh and settle in 30 seconds, and silt, which does not settle in 1 minute. Sand-index : The number proportional to its total fineness considered from the economical point of view, as explained on page 93. Absolute extraction : The percentage of values actually brought into solution. Actual extraction: The percentage of values actually brought to the ziuc-boxes. Units : Dollars, U. S. Currency; pounds; and short tons (2,000 lb.). Gold is valued at $20.67, and silver at $0.50 per ounce. Screens : In the sizing-tests the screens used were:¬ Mesh (per 1 in.), . 24 30 40 60 80 100 150 200 250 Aperture (mm.), . 0.740 0.515 0.424 0.250 0.159 0.111 0.090 0.067 0.058 Strengths of solution : Strengths are expressed in the percent- . age of KCN contained, though the sodium cyanide, which is

Jan 1, 1906

By John D. Wiebmer

First, a definition of a small scale miner is in order. The US Bureau of Mines classifies him as one who produces 360 t/d (400 stpd) of ore or less. In Canada, he would be refered to as a "junior company." Mexico identifies the small scale miner as one whose gross income from operations is less than $880,000 per year. A small surface mine in India employs less than 400 people, and a small underground mine employs less than 150. Peru considers a small scale miner one who produces less than 54 000 t/y (60,000 stpy) of ore. Obviously, the term is relative. What may be a small mine in one country is a medium or large mine in another. This lack of agreement is understandable since small scale mining does not often cross national boundaries. Rather, its effects are felt at the regional and local levels within each nation. Its importance doesn't lie with any huge contribution to the GNP or balance of trade. Instead, its value is as a local employer and as a frontrunner in geologic exploration.

Jan 2, 1979