Search Documents

By J. E. Chappelear

We are concerned with the problem of calculating the forces produced by passing waves on a submerged object (in particular a drilling barge) located on the ocean floor. We employ the linearized theory of waves (the Airy1 theory), since solutions are generally more easily obtained in such a theory. It will be indicated how an approximate solution to the problem can be obtained for waves of finite height by use of a linear combination of Airy waves. We shall assume the submerged object has an infinite length, thus neglecting diffraction and making the problem two-dimensional. We find that there is not a considerable difference between our solution and the usual engineering solution. The force, as a function of time, is plotted in Figs. 4 and 5, together with the usual solution for easy comparison. So far, no experiments have been found to compare with the results. As will be shown, the calculations can be extended to waves of finite height (Stokes2-Struik3 waves) in an approximate fashion. This can be done by calculating the force produced by each Fourier component of the wave, separately, and omitting the coupling between the various harmonics produced by Bernoulli's theorem. The problem and its boundary conditions will be briefly stated. We seek a function, +, the velocity potential, which is harmonic, ?2?=0...........(1) and which satisfies the boundary conditions ??/?n =0 .......(2) (the normal derivative of + is zero) on the ocean floor and the sides of the barge, and s??/?y = ?..........(3) on the ocean surface, where s = g/w2........(4) The physical reasons for these choices and an interpretation of ? are given by Lamb.' As previously stated, we assume also that the problem is two-dimensional. We set up our coordinates such that x = 0 is the center of the barge and y = 0 is the ocean floor. The coordinates are shown in Fig. 1, together with the location of the barge on the bottom. Our solution may be decomposed into a function which is symmetric about x = 0,?e, and one which is antisymmetric, +,, ? = ? + ?o...........(5) Thus directly above the barge we have as boundary conditions that for x = 0, ?o = 0, ...........(6) and ??e/?x = 0........(7) Now, far from the barge, we have that (for x positive and assuming the waves are incident from the left) ?e ? Ae cosh ky cos k (x + a) , . . . (8) and ?e ? Ao cosh ky cos k (x + ß) . . . . (9) where + means ". .. approaches ... for x large." Let us put Ae, Ao, and k equal to one, and remember that, in accordance with the derivation of Eq. 3, a sinusoidal time factor is to be supplied. Then we may rewrite Eq. 8 for ?e, and we find that

Jan 1, 1958

By Frank H. Kingdon

and eventually we would have trouble. That is, these little localized overstresses may not be important if the structure is loaded a few times, but may be important if the structure is loaded many thousands of times. The existence of localized stress has been demonstrated by direct experimentation with delicate extensometers by the elaborate investigations of Coker. Localized stresses four, five, and six times those that we would get by the ordinary laws of mechanics exist in most of our structures. These stresses, ordinarily, under steady load do no damage but if they are repeated many times may start progressive failure. So far, we have seen no failure that could not be explained by localized high stress at a nick, a crack, a point where one heat treatment stopped and another began, or where there was local faulting, or any one of a dozen causes. In the case of drill rods, the actual distribution of stress must be different from that which any mathematical analysis could predict. It would seem that the spread of damage from the localized overstresses, so far as we can see now, explains the phenomenon known as fatigue. The Ideal Drill Steel By Frank H. Kingdon The essential qualities of a drill steel are: (I), It must be easily forged; (2), the forged bit end must permit easy heat treatment to obtain hardness to resist chipping; (3)) the bar or body must be stiff to resist bending or twisting and yet tough to resist shock and vibration, with resulting breakage, (4), the forged shank end must be easily heat treated to obtain hardness with great toughness. Minor requirements are that the bit and the shank are in alignment with the body; that the shank is of the proper shape and length and the shank collar or lugs of the proper diameter and length; that the hole is free from obstruction; that the striking end of the shank is flat and square; that the bit is of the proper shape, with the cutting and reaming edges formed full and to the required size; that the reaming edges are concentric with the axis of the steel, and that there are no sharp corners at the shoulder where the bit blends into the body. The essential qualities of a bit, are: That its shape be such that maximum cutting speed can be maintained for as great a distance as possible before wear of the gage and cutting edge reduces the speed of penetration to a point where a change of steel is made necessary; that the size or diameter of the drill hole corresponding to the gage of the bit can be maintained with the least possible reduction as the depth of the hole increases, and that the bit can be correctly and readily formed and heat treated. The following features of bit design require attention: Shape,

Jan 1, 1922

SLAG composition, slag constitution, reactions in slag, and reactions between slag and metal-in other words, the physical chemistry of slags-are matters of great importance to the open-hearth operator, whether or not he makes use of any detailed knowledge of them. Although this is a relatively young branch of the science of steel- making, much progress has been made; however, much remains to be learned, and many of the statements that can be made at present are probably--or even certainly-subject to future change. Nevertheless, the physical chemistry of slags is sufficiently developed to provide a reasonably secure basis for real understanding of steelmaking reactions. FUNDAMENTALS OF SLAG CONTROL By way of introduction, some time is spent in this chapter on effecting an easy transition from some of the more "practical" manifestations of slag to discussions couched in the more formal language of physical chemistry. This necessitates a certain amount of repetition, but it is felt that the purpose of the chapter is best served in this way. Reactions in the metal phase have products that find their way into the slag and are important components thereof; they are discussed in detail in the preceding chapter. Some substances distribute themselves Between slag and metal in definite fashion, and others are found only in the slag. Their reactions are a large reason for this chapter. Limitations of Slag Control. The open-hearth process is essentially oxidizing and cannot be otherwise operated. (Oxygen gradients in the furnace, the mechanism of oxygen inflow, and similar subjects are discussed in Chapter XIX.) As shown in the calculations of material and heat balances for the charge (see Chapter XV), from 25 to 50 lb. of oxygen will flow from air or combustion gases into the charge or molten bath during the heat for each ton of liquid steel

Jan 1, 1944

By James F. Howe

EveRy engineer and user of wire rope is desirous of information that will enable him to determine whether the performance of any particular piece of rope is satisfactory, and what conditions can be changed so as to increase the life of a rope. In most cases, it is far from easy to analyze the conditions of service and tell which is the greatest factor in determining the life of wire rope. If we start on a layout for an entirely new rope system, the task of making conditions satisfactory is simplified so far as the engineering details are concerned; but if the plant requiring wire rope is in operation, any change is likely to involve the expenditure of considerable money to replace and change over machinery that must be kept in constant operation, because a large monetary loss will result from a shutdown for even a few days. Often wire rope is kept operating under bad conditions, as the user thinks that it is cheaper and quicker to replace the rope than to make alterations in the hoisting machinery. A typical case is a metal mine operating in what is now almost the center of a large mining city, where it owns a few acres of mineral rights. It was expected that the shaft would go to a depth of 1000 ft. (305 m.), so a moderate-sized rope, about 1 1/4in. (31.7 mm.), was used on a 6-ft. drum with a 7-ft. head-frame sheave and rather short lead from drum to head sheave. This mine has gone deeper each year until it is now 2500 ft. deep and the rope speed has been increased from 1500 ft. per min. to over 3000 ft. The original rope just filled the drum in one layer, now it overwinds three layers. The original ropes were probably 6 X 19 crucible steel and lasted from 12 to 18 mo.; now, the highest grade plow steel is used, yet the average service is only about 6 mo. The cause is not hard to find. If the engineers had known at the outset what would be done with this hoist, the design would have been very different. Conditions at this mine, from a wire-rope standpoint, have gradually become worse and it is difficult to see how rope service on this hoist can be compared with the service of previous years with any fairness to the wire-

Jan 1, 1923

By A. T. Beckwith

THE Lehigh Navigation Coal Company Inc. operates steep-pitch, relatively deep mines in the Panther Creek Valley, at the eastern end of the southern anthracite coal field. Commercially minable coal beds are the Mammoth,† Primrose, Orchard, and Buck Mountain,‡ their respective thicknesses average 50, 15, 1o and 12 ft. Sand slates immediately overlie and underlie these beds, though in some locations sandstone or conglomerate beds occur. Underground operations extend to a depth of 1200 ft. below the surface, and comprise a bulk of virgin work on the lower levels, and a small amount of remining on the upper levels. With increase in depth, ventilation has become a more important factor. DEVELOPMENT In early days slopes or drifts were driven in the outcropping coal on the hillsides. Subsequent development was by water-level tunnels, with portals above high water in Panther Creek. These tunnels have been maintained because they intercept and drain much water that enters the mined-out portion of the bed and otherwise would follow down to the deep workings. Below these tunnels, the coal was customarily developed by slopes. Muleways, which are zigzag chutes easy to travel, were also driven to connect lower openings with the water levels. When it became necessary to go still deeper, the slopes were abandoned, and vertical multicompartment shafts were sunk from the surface. Levels have been at vertical intervals of from 195 to 250 ft. Recent practice has been toward the latter spacing; splitting the total lift, however, by starting to mine from chutes extending halfway up to the level above. Chutes customarily are spaced at 50, 60 or 70-ft. centers along the gangways. At some mines, additional shafts have been sunk from the surface to the level containing the main pumping station, and these carry the discharge lines from the pumps. As the mines are ventilated by the exhausting system, both the hoisting and so-called water shafts serve as intakes. The main fan is always on the surface, and is connected with the return airways from the various levels by an air hole or a vertical shaft. For economy, when the present deepest levels were developed, main return-air shafts or air holes were not extended to the new level, but connections were made from the new level to that above by two or more holes. It is doubtful that this method will be continued, as complications in the system, increased resistance to flow, and other difficulties undoubtedly will counterbalance any economies this provision may afford.

Jan 1, 1942

AT the meeting of the Board of Directors held on June 25, 1926, and in response to numerous in-dividual suggestions for changes, a committee on Re-vision of the Constitution and By-Laws of the Insti-tute was appointed, consisting of C. F. Rand, Archi-bald Douglas and H. Foster Bain. Various confer-ences were held, much correspondence conducted and a preliminary draft was prepared. It proved imprac-ticable to complete the work in time to submit the matter to the membership for approval or disapproval at the annual meeting in 1927, and the Committee was continued with instructions to prepare a report as a basis of action in 1928. After Mr. Rand's death George Otis Smith was appointed in his place and the tentative draft herewith submitted has been pre-pared in its present form by Messrs. Smith, Douglas and Bain, though not differing in any material mat-ter from an earlier draft approved by Mr. Rand. In preparing this the Committee has kept in mind primarily the desirability of simplification and of making the By-Laws conform to the actual practice of the Institute as worked out through experience. The Constitution and By-Laws adopted in 1912, and which with minor amendments only still govern the Insti-tute, are full of specific provisions regarding pro-cedure; such as that laid down for guidance of the Papers and Publications Committee. Many of these have proved unworkable and in practice have not been always strictly followed. It now seems wise to write into the Constitution and By-Laws only the general fun-damental principles to he followed and to provide for such easy change in methods of following them out as will permit efficient conduct of the business. It is this thought that has guided the Committee in rewrit-ing many of the sections. With this in view also the Constitution, as such, has been shortened to the brief-est feasible statement of fundamentals. All matters relating to means of making these principles effec-tive have been put into the By-Laws or in the hands of committees whose work is subject to control and whose rules are subject to approval or disapproval by the Board of Directors. Many suggestions for changes have come to the Committee that have not been incorporated in this draft. Some of these are in themselves excellent but have not been incorporated here because the Commit-tee discovered no sentiment for them such as would be likely to secure their approval, or found them out of harmony with the general plan followed herein.

Jan 9, 1927

By D. McLean

For many pu@oses uniform strength is desired over a long temperature range, coupled to a band of softness at the hot end for easy shaping. Various types of material fulfill such a requirement to different degrees, depending on the regularity of their atomic structure. In long-chain polymers and vitreous glasses the irregular structure leads to a steep temperature dependence of deformation resistance and the temperature band between the hard and brittle condition and the soft condition is only about 100 C. In crystals and especially metals the atomically regular structure leads to a much smaller sensitivity over a wide temperature band, thus approaching the ideal behavim. The reason for this insensitivity is that the regular crystalline structure deforms by the movement of dislocations and the elastic interactions of dislocations in- PLASTICS, GLASSES, AND CRYSTALS The ease or otherwise of deformation varies with temperature much more in some substances than in others. This is an important matter when service over a wide temperature range is needed, especially volve energies of several hundred electron volts compared with which the energy of thermal agitation is insignificant. However, temperature affects a metal's defmmation resistance through its influence on the annealing, m coarsening, of the three-dimensional dislocation network. This coarsening is a phenomenon very similar to grain growth and ideas about grain growth can be applied to it. Taking into account also the temperature dependence of the glide resistance from alloying additions, a reasonable account can be given of the overall effect of temperature on deformation strength and of stress and grain size on deformation rake. Special structures me described. some arising from these ideas and as yet untried, which may benefit metals and polymers but not ni-treous glasses. when in addition a degree of softness suitable for shaping is required at some stage. It would be nice if one could write on this subject in as much detail about plastics, glasses, and so forth, as about metals, but there has been far more study of this matter in metals than in other substances, which is one reason why most of this paper concerns metals. However, in Fig. 1 there are shown the deformation strengths of several nonmetallic substances as a function of temperature. In many tests the attempt at deformation caused breakage and the graph lines are then drawn dashed. Long-chain plastics, a glass, and a crystalline substance are included in Fig. 1. The notable feature of all of them is the sensitivity of the

Jan 1, 1969

By James Howe

EVERY engineer and user of wire rope is desirous of information that will enable him to determine whether the performance of any particular piece of rope is satisfactory, and what conditions can be changed so as to increase the life of a rope. In most cases, it is far from easy to analyze the conditions of service and tell which is the greatest factor in determining the life of wire rope. If we start on a layout for an entirely new rope system, the task of making conditions satisfactory is simplified so far as the engineering details are concerned; but if the plant requiring wire rope is in operation, any change is likely to involve the expenditure of consider-, able money to replace and change over machinery that must be kept in constant operation, because a large monetary loss will result from a shutdown for even a few days. Often wire rope is kept operating under bad conditions, as the user thinks that it is cheaper and quicker to replace the rope than to make alterations in the hoisting machinery. A typical case is a metal mine operating in what is now almost the center of a large mining city, where it owns a few acres of mineral rights. It was expected that the shaft would go to a depth of 1000 ft. (305 m.), so a moderate sized rope, about 1 ¼ in. (31.7 mm.), was used on a 6-ft. drum with a 7-ft. head-frame sheave and rather short lead from drum to head sheave. This mine has gone deeper each year until, it is now 2500 ft. deep and the rope speed has been increased from 1500 ft. per min. to over 3000 ft. The original rope just filled the drum in one layer, now it overwinds three layers. The original ropes were probably 6 X 19 crucible steel and lasted from 12 to 18 mo.; now, the highest grade plow steel is used, yet the average service is only about 6 mo. The cause is not hard to find. If the engineers had known at the outset what would be done with this hoist, the design would have been very different. Conditions at this mine, from a wire rope standpoint, have gradually become worse and it is difficult to see how rope service on this hoist can be com-pared with the service of previous years with any fairness to the wire-

Jan 2, 1922

By James F. Howe

EveRy engineer and user of wire rope is desirous of information that will enable him to determine whether the performance of any particular piece of rope is satisfactory, and what conditions can be changed so as to increase the life of a rope. In most cases, it is far from easy to analyze the conditions of service and tell which is the greatest factor in determining the life of wire rope. If we start on a layout for an entirely new rope system, the task of making conditions satisfactory is simplified so far as the engineering details are concerned; but if the plant requiring wire rope is in operation, any change is likely to involve the expenditure of considerable money to replace and change over machinery that must be kept in constant operation, because a large monetary loss will result from a shutdown for even a few days. Often wire rope is kept operating under bad conditions, as the user thinks that it is cheaper and quicker to replace the rope than to make alterations in the hoisting machinery. A typical case is a metal mine operating in what is now almost the center of a large mining city, where it owns a few acres of mineral rights. It was expected that the shaft would go to a depth of 1000 ft. (305 m.), so a moderate-sized rope, about 1 1/4in. (31.7 mm.), was used on a 6-ft. drum with a 7-ft. head-frame sheave and rather short lead from drum to head sheave. This mine has gone deeper each year until it is now 2500 ft. deep and the rope speed has been increased from 1500 ft. per min. to over 3000 ft. The original rope just filled the drum in one layer, now it overwinds three layers. The original ropes were probably 6 X 19 crucible steel and lasted from 12 to 18 mo.; now, the highest grade plow steel is used, yet the average service is only about 6 mo. The cause is not hard to find. If the engineers had known at the outset what would be done with this hoist, the design would have been very different. Conditions at this mine, from a wire-rope standpoint, have gradually become worse and it is difficult to see how rope service on this hoist can be compared with the service of previous years with any fairness to the wire-

Jan 1, 1923

By J. M. Callow

H. A. MEGRAW, New York, N.,Y.-One interesting thing that might be brought out in this connection is the cost of making sulphide gas. I had a communication the other day which suggested that, in view of the high cost of oil, sulphur and sodium sulphide, we might make use of a well-known chemical reaction to form this sulphide gas by the use of aluminum sulphide. It is difficult to see any advantage in this, however, since aluminum has been affected just as much as any other commodity by the rise in prices, due, to war conditions. RUDOLF GAHL, Miami, Ariz. (communication td the Secretary*) Mr. Callow refers to my paper, History of Flotation at Inspiration, which was presented at the Arizona meeting of the Institute. These notes of Mr. Callow's contain much valuable information on flotation practice, as is to be expected from an article written by an author of Mr. Callow's experience in this branch of metallurgy. Nevertheless, I cannot help contradicting a number of the statements made in the references to my paper. In passing, I will also say a word about the reference in Mr. Callow's paper to the article by Messrs. Laist and Wiggin entitled "Flotation Concentration at Anaconda, Mont." Mr. Callow calls attention to the fact that evidently Callow flotation machines are not very sensitive, inasmuch as one man per shift handles four 800-ton sections of Callow machines or 3,200 tons per day at the Inspiration plant. While-it has been the experience of the Inspiration company that the four sections of Callow machines in the Inspiration concentrator are easily handled by one American operator per shift, it is only fair to state that each man operating four sections is assisted by two Mexican helpers who constantly clean the bottoms of the machines. The tonnage per section, by the way, whether equipped with Callow,, Inspiration or Minerals Separation machines, is considerably in excess 4 800 tons.. Mr. Callow further says that local opinion at Inspiration is that, two 800-ton sections consisting of two 10-compartment and four 6-compartment Minerals Separation machines (these machines are of the Hebbard type) is the limit that one man can properly attend. I do not hesitate to say that I consider it perfectly feasible to have four such sections operated by one man, perhaps assisted by "one helper. The Minerals Separation machines of this type have undoubtedly an advantage as far as easiness of operation is concerned,

Jan 4, 1917

By John R. Spencer

A capillary tube variable volume cell is described, which has operated satisfactorily over a range of 100°F and 3,500 psi to 550°F and 1,500 psi. The cell contents are entirely visible over the length of the capillary with the exception of a space at the top amounting to three per cent of the total volume. Observations on the critical behavior of simple systems have been greatly facilitated by the apparatus, it being possible to establish the critical conditions for a particular mixture in the course of a day's run. INTRODUCTION Many types of apparatus have been designed for obtaining data on the phase relationships of hydrocarbon systems. Such apparatus can in general be subdivided into two classifications; (l), indirect measurement of phase volume, and (2), direct visual observation of phase volume, each of which has outstanding advantages and disadvantages. Indirect measurement of phase volume requires the use of rather elaborate apparatus including internal probes in which are located the device for determining the locus of the interface between phases. Such equipment is by its very nature costly, and is complex from the standpoint of operating technique. Probing techniques can be used, however, over wide ranges of temperature and pressure with a high degree of reproducibility. Apparatus for visual observation of phase behavior obviously has the advantage of enabling the experimenter to see exactly what takes place, but because the material to be tested is contained in a cell constructed of both metal and glass, is limited severely as to the temperature range of operation. Furthermore. the maximum pressure usually is limited by the choice of material used for sealing the glass to the metal, and by the strength of the glass itself. In the interest of increased efficiency of observation, as much of the cell as possible should be visible to the eye. Glass capillary tubes have been used successfully but have always given difficulty at the metal-to-glass seal. An apparatus has been devised to overcome the problems of sealing and resistance to temperature effects that have heretofore been the limiting factor with glass apparatus in the observation of phase volumes at elevated temperature and pressure. APPARATUS The objective which dictated the general arrangement of the apparatus (Figs. 1 and 2) was simplicity of operation. The air bath, A, was constructed of an iron framework to which was attached approximately one inch of glass wool bats which were covered on the outside with "Masonite." A roughly octagonal center piece was installed to provide forced circulation of the air by the fan, B, past the heaters, D, cell, F, and thermoregulator, C, respectively. The entire top of the box is removable to facilitate charging of the cell and to permit easy maintenance. Two windows are provided before and behind the cell to allow the operator to observe the contents against the background fluorescent light, E. The heaters,

Jan 1, 1951

By L. P. Davidson

ThE new electrolytic zinc plant of the American Zinc Company of Illinois commenced operation in April 1941. The simple flowsheet using the standard current density and the economic reasons that dictated it are given herewith. The Evans-Wallower Zinc Co. built an electrolytic zinc plant at Monsanto, Ill., in 1929 and operated it for about two years. The plant stood idle from 1932 and was purchased by the American Zinc Co. in 1940. Because of the condition of the equipment, excepting the motor generator set, a complete rebuilding was necessary. The Fairmont City plant of the American Zinc Co. could treat the leach residues, the purification cake and the skimmings from the melting furnace in its various plants. This possibility permitted a simple flowsheet with good economic results. The flowsheet is shown in Fig. I. The calcined concentrates are leached in mechanically agitated tanks with spent electrolyte and such ferric iron solution as necessary. When the acid has been neutralized and the iron coagulated, the fluid is discharged to settling tanks. The underflow from these thickeners is filtered on a Moore filter; the filter cake leaves the plant for retreatment and the filtrate joins the thickener overflow. Zinc dust is added to this solution until the copper and cadmium are precipitated. The pulp is filtered through Shriver presses, which deliver the purified solution to stor- age tanks, and the copper-cadmium-zinc cake is shipped for retreatment and recovery of these three metals. The purified solution is electrolyzed; the regenerated acid is returned for use in the leaching plant and the cathode zinc, after stripping, goes to the melting furnace, from which it is cast in slabs. The skimmings from the melting furnace are shipped to the Fairmont City plant for reduction to metal in the retort furnaces. The choice of this simple flowsheet was made possible only because of the facilities of the Fairmont City plant. The long leaching pried, with high acid content and high temperature which characterize the high-density process, gives a higher zinc extraction but also dissolves more impurities, which must be removed. The same is true to a lesser degree of the multi-step leaching of the western low-density plants. By the sacrifice of some initial extraction, solutions can be obtained that are relatively easy to purify and give good ampere efficiency. This loss in initial extraction is made up in the retreatment of the residues in the Waelz plant. The impurities that accompany the zinc thus extracted are inconsequential when the Waelz product is treated in a distillation plant. It was recognized that this flowsheet would require a somewhat greater amount of sulphuric acid—-eithcr as acid or as sulphate sulphur in the calcine—because of poorer washing. The sulphuric acid plant at Fairmont City could deliver 60" Bè. acid to compensate for the sulphate loss and the cost would be less than the cost of more intensive washing.

Jan 1, 1943

By G. B. Craig, G. L. Montgomery

A simple technique has been developed which reveals glide dislocations in zone-refined aluminum as etch pits. The technique has been tested quantitatively by making dislocation counts on aluminum single crystals deformed in pure bending. The method has the advantage of being insensitive to the orientation of the surface under examination. A number of etchants which will reveal dislocations in annealed aluminum have been reported.'-' These etchants apparently depend on decoration of the dislocations by an impurity (probably iron) and cannot, therefore, be used to reveal fresh glide dislocations. In addition, it is unlikely that screw dislocations will be etched because of their small attraction for impurity atoms. Amelinckx6 has reported that glide dislocations located along slip traces can be revealed by fluo-rated aqua regia. This work indicated that dislocations themselves, irrespective of decoration by impurity atoms, are responsible for the etch pits. However, as a result of additional etching experiments, Wyon and Marchin7 concluded that dislocations alone are not sufficient to explain the localization of etch pits on slip lines in aluminum using chemical etch-pitting techniques. In addition, their results show that glide dislocations are revealed only on surfaces approximately parallel to a (100) axis and that not all slip systems are attacked. These observations have been confirmed by the present authors. The technique described in this article is insensitive to the orientation of the surface, and reveals dislocations on all glide systems. Fig. 1 shows a deformed region in the neighborhood of a scratch. Dislocations can be seen along three slip traces. In the present work, single crystals of zone-refined aluminum are polished for from 2 to 5 min in a chemical polishing reagent held at 100°C, as described by Herenguel and second:' H2Sol 60 pct H3PO4 30 pct HNO3 10 pet The samples are then coated with a thin oxide film by annealing in air at 450°C for 1 hr and cooling in the furnace. After deformation, dislocation etch pits are developed by immersing the specimen in the same polishing solution which is now held at a temperature of 50°C. The formation of small hydrogen bubbles indicates that etching has occurred. The sample is immediately removed from the solution. Prolonged etching results in enlargement of the pits and, in regions of high dislocation density, the overlapping and loss of resolution of individual pits. It is the experience of the authors that contact with iron will ruinously contaminate the reagent. With careful etching, dislocations separated by half a micron can be resolved optically and the method has been shown to be sufficiently sensitive to reveal dislocations produced during the pre-easy glide region of deformation, Fig. 2. A few examples of glide-dislocation configurations, as revealed by this technique, are shown in Figs. 1 to 4.

Jan 1, 1964

By T. W. Smoot

Bentonites are composed chiefly of montmorillonites which are clay minerals generally distinguished from other clay minerals by their surface activity and extremely fine particle sizes. The uses of bentonite are many and varied, depending principally on one or more of the following characteristics: 1) Thixotropy, 2) Dispersion, 3) Plasticity, 4) Swelling, 5) Surface area, activity, ab- and adsorbtive properties. Some of the major uses of bentonite are briefly reviewed as are the mineralogical and physical properties. The uses of X-ray diffraction, differential thermal analysis and other tests for physical properties are reviewed as to their uses in evaluation. In the past 40 years, the industrial uses of bentonite have grown to include many applications. The physical and chemical properties of bentonites are such that they can be used as catalysts, adsorbants, plasticizers, binders, drilling muds, and pelletizers. Not all bentonites, however, can be used for all of these purposes and some are probably of little or no value for any use. The purpose of this paper is to briefly review the mineralogical, physical, and chemical characteristics and variations of bentonites. The determination of these characteristics and their uses in industry are also reviewed so that these determinations can be used as guides for evaluation. DEFINITION OF BENTONITE The word bentonite, as used in this paper, refers to a clay material, usually (but not necessarily) the result of the in-place-weathering of volcanic ash. Its mineralogical composition is dominated by the clay mineral montmorillonite and generally carries other clay minerals and silica minerals as the major 'impurities'. For this discussion, such a definition is justified since most of the economic uses of bentonite~ depend upon the physical and chemical characteristics of the montmorillonite minerals involved. The terms montmorillonite and bentonite have been used almost interchangeably in industry although the latter is much more commonly used. Therefore, where montmorillonite is discussed, it should be understood that the major feature of a bentonite is the subject. STRUCTIJRE OF MONTMORILLONlTE The economic importance of bentonites is generally based on one or more of the following characteristics of montmorillonite: 1) high-thixotropy and easy dispersion in water, 2) high-plasticity, 3) swelling properties, 4) large surface area/unit mass, 5) high surface activity, and 6) adsorptive properties. To understand these properties, an appreciation of the structural scheme of montmorillonite is helpful. Montmorillonite IS one of the three-layer clay minerals composed essentially of hydrous aluminum silicates. The essential building blocks of these layered silicate:; are: 1) silica tetrahedron composed of a silicon atom surrounded by four oxygen atoms, and 2) aluminun (iron, magnesium, etc.) octahedral unit that, ideally, has one of these atoms surrounded by six hydroxal units. Fig. 1 is a diagrammatic sketch of the montmorillonite structure. In the montmorillonite structure, the tetrahedron are pointed inward and attached to the octahedral units so that the O= atoms replace the hydroxal units where they are bonded; hence two-thirds of the hydroxal units

Jan 1, 1962

By L. P. Davidson

ThE new electrolytic zinc plant of the American Zinc Company of Illinois commenced operation in April 1941. The simple flowsheet using the standard current density and the economic reasons that dictated it are given herewith. The Evans-Wallower Zinc Co. built an electrolytic zinc plant at Monsanto, Ill., in 1929 and operated it for about two years. The plant stood idle from 1932 and was purchased by the American Zinc Co. in 1940. Because of the condition of the equipment, excepting the motor generator set, a complete rebuilding was necessary. The Fairmont City plant of the American Zinc Co. could treat the leach residues, the purification cake and the skimmings from the melting furnace in its various plants. This possibility permitted a simple flowsheet with good economic results. The flowsheet is shown in Fig. I. The calcined concentrates are leached in mechanically agitated tanks with spent electrolyte and such ferric iron solution as necessary. When the acid has been neutralized and the iron coagulated, the fluid is discharged to settling tanks. The underflow from these thickeners is filtered on a Moore filter; the filter cake leaves the plant for retreatment and the filtrate joins the thickener overflow. Zinc dust is added to this solution until the copper and cadmium are precipitated. The pulp is filtered through Shriver presses, which deliver the purified solution to stor- age tanks, and the copper-cadmium-zinc cake is shipped for retreatment and recovery of these three metals. The purified solution is electrolyzed; the regenerated acid is returned for use in the leaching plant and the cathode zinc, after stripping, goes to the melting furnace, from which it is cast in slabs. The skimmings from the melting furnace are shipped to the Fairmont City plant for reduction to metal in the retort furnaces. The choice of this simple flowsheet was made possible only because of the facilities of the Fairmont City plant. The long leaching pried, with high acid content and high temperature which characterize the high-density process, gives a higher zinc extraction but also dissolves more impurities, which must be removed. The same is true to a lesser degree of the multi-step leaching of the western low-density plants. By the sacrifice of some initial extraction, solutions can be obtained that are relatively easy to purify and give good ampere efficiency. This loss in initial extraction is made up in the retreatment of the residues in the Waelz plant. The impurities that accompany the zinc thus extracted are inconsequential when the Waelz product is treated in a distillation plant. It was recognized that this flowsheet would require a somewhat greater amount of sulphuric acid—-eithcr as acid or as sulphate sulphur in the calcine—because of poorer washing. The sulphuric acid plant at Fairmont City could deliver 60" Bè. acid to compensate for the sulphate loss and the cost would be less than the cost of more intensive washing.

Jan 1, 1943

By John R. Spencer

A capillary tube variable volume cell is described, which has operated satisfactorily over a range of 100°F and 3,500 psi to 550°F and 1,500 psi. The cell contents are entirely visible over the length of the capillary with the exception of a space at the top amounting to three per cent of the total volume. Observations on the critical behavior of simple systems have been greatly facilitated by the apparatus, it being possible to establish the critical conditions for a particular mixture in the course of a day's run. INTRODUCTION Many types of apparatus have been designed for obtaining data on the phase relationships of hydrocarbon systems. Such apparatus can in general be subdivided into two classifications; (l), indirect measurement of phase volume, and (2), direct visual observation of phase volume, each of which has outstanding advantages and disadvantages. Indirect measurement of phase volume requires the use of rather elaborate apparatus including internal probes in which are located the device for determining the locus of the interface between phases. Such equipment is by its very nature costly, and is complex from the standpoint of operating technique. Probing techniques can be used, however, over wide ranges of temperature and pressure with a high degree of reproducibility. Apparatus for visual observation of phase behavior obviously has the advantage of enabling the experimenter to see exactly what takes place, but because the material to be tested is contained in a cell constructed of both metal and glass, is limited severely as to the temperature range of operation. Furthermore. the maximum pressure usually is limited by the choice of material used for sealing the glass to the metal, and by the strength of the glass itself. In the interest of increased efficiency of observation, as much of the cell as possible should be visible to the eye. Glass capillary tubes have been used successfully but have always given difficulty at the metal-to-glass seal. An apparatus has been devised to overcome the problems of sealing and resistance to temperature effects that have heretofore been the limiting factor with glass apparatus in the observation of phase volumes at elevated temperature and pressure. APPARATUS The objective which dictated the general arrangement of the apparatus (Figs. 1 and 2) was simplicity of operation. The air bath, A, was constructed of an iron framework to which was attached approximately one inch of glass wool bats which were covered on the outside with "Masonite." A roughly octagonal center piece was installed to provide forced circulation of the air by the fan, B, past the heaters, D, cell, F, and thermoregulator, C, respectively. The entire top of the box is removable to facilitate charging of the cell and to permit easy maintenance. Two windows are provided before and behind the cell to allow the operator to observe the contents against the background fluorescent light, E. The heaters,

Jan 1, 1951

By C. W. Donnelly, Louise B. Freeman, Coleman D. Hunter

It is with pride that the authors of this paper report. that during 1944 the production of petroleum in Kentucky passed its all-time peak, 9,496,985 bbl. being contributed. The delivery of natural gas, especially from eastern Kentucky, was maintained and possibly exceeded the highest deliveries of the past. To raise the production of oil and gas was not easy with inferior and worn-out equipment and the shortage of skilled labor. Reminiscent of the early days of the industry in the state, particularly in the hills of Elliott County, where mud roads often have gradients of 45º, was the replacement of worn-out trucks and tractors by oxen. Of the total 9,496,985 bbl., 17 per cent was contributed by the part of Kentucky that is east of the Cincinnati arch, as compared with the total of 7,010,776 bbl. contributed in 1943, of which 25 per cent was contributed by eastern Kentucky. This discrepancy is due to the discovery of more new fields in western Kentucky rather than to a decrease in production in the eastern fields, where the average has been maintained by reconditioning and secondary recovery of old fields and further development of new pools reported for the first time in 1943. In all, 1103 wells were known to have been drilled in the state during 1944, of which 659 were drilled in western Kentucky and 444 in eastern Kentucky. The exact number of wells drilled for any year is never known, as drilling permits are not required except 'when it is planned to drill through a workable coal seam. Of the total number of wells drilled, 459 were oil wells, 229 gas wells and 415 dry holes. The monthly production was as follows: January........................... 659,496 February.......................... 658,606 March...................... ...... 711,619 April............................. 649,926 May............................... 754,892 June.............................. 730,369 July.............................. 761,762 August............................ 878,053 September...................... 863,150 October........................... 968,732 November........................ 961,999 December........................ . 898,636 Western Kentucky In western Kentucky 352 wells were completed as oil wells with a total initial production of 47,922 bbl. of oil, the average being 136 bbl. per well. Two wells produced gas, the total initial production being 1,594,000 cu, ft. One hundred and eighteon wildcat wells were drilled, of which 107 were dry holes and 11 were oil wells. Three of the latter proved to be the discovery wells of commercial pools. Twelve new pools were discovered during 1944, none of major importance, as indicated in Table 2. The Utley pool, due to a stratigraphic trap on the flank of a closed structure, found oil in the Mcclosky at 2565 ft. in the discovery well, with initial productioil of 1000 bbl. The average daily production is now 227 bbl. from seven wells. The East Poole field, with the discovery well in the Tar Springs sandstone at 1811

Jan 1, 1945

By L. P. Davidson

THE new electrolytic zinc plant of the American Zinc Company of Illinois commenced operation in April 1941. The simple flowsheet using the standard current density and the economic reasons that dictated it are given herewith. The Evans-Wallower Zinc Co. built an electrolytic zinc plant at Monsanto, Ill., in 1929 and .operated it for about two years. The plant stood idle from 1932 and was purchased by the American Zinc Co. in 1940. Because of the condition of the equipment, excepting the motor generator set, a complete rebuilding was necessary. The Fairmont City plant of the American Zinc Co. could treat the leach residues, the purification cake and the skimmings from the melting furnace in its various plants. This possibility permitted a simple flowsheet with good economic results. The flowsheet is shown in Fig. I. The calcined concentrates are leached in mechanically agitated tanks with spent electrolyte and such ferric iron solution as necessary. When the acid has been neutralized and the iron coagulated, the fluid is discharged to settling tanks. The underflow from these thickeners is filtered on a Moore filter; the filter cake leaves the plant for retreatment and the filtrate joins the thickener overflow. Zinc dust is added to this solution until the copper and cadmium are precipitated. The pulp is filtered through Shriver presses, which deliver the purified solution to storage tanks, and the copper-cadmium-zinc cake is shipped for retreatment and recovery of these three metals. The purified solution is electrolyzed; the regenerated acid is returned for use in the leaching plant and the cathode zinc, after stripping, goes to the melting furnace, from which it is cast in slabs. The skimmings from the melting furnace are shipped to the Fairmont City plant for reduction to metal in. the retort furnaces. The choice of this simple flowsheet was made possible only because of the facilities of the Fairmont City plant. The long leaching period, with high acid content and high temperature which characterize the high-density process, gives a higher zinc extraction but also dissolves more impurities, which must be removed. The same is true to a lesser degree of the multi-step leaching of the western low-density plants. By the sacrifice of some initial extraction, solutions can be obtained that are relatively easy to purify and give good ampere efficiency. This loss in initial extraction is made up in the retreatment of the residues in the Waelz plant. The impurities that accompany the zinc thus extracted are inconsequential when the Waelz product is treated in a distillation plant. It was recognized that this flowsheet would require a somewhat greater amount of sulphuric acid-either as acid or as sulphate sulphur in the calcine-because of poorer washing. The sulphuric acid plant at Fairmont City could deliver 60° Be. acid to compensate for the sulphate loss and the cost would be less than the cost of more intensive washing.

Jan 1, 1942

By L. P. Davidson

THE new electrolytic zinc plant of the American Zinc Company of Illinois commenced operation in April 1941. The simple flowsheet using the standard current density and the economic reasons that dictated it are given herewith. The Evans-Wallower Zinc Co. built an electrolytic zinc plant at Monsanto, Ill., in 1929 and operated it for about two years. The plant stood idle from 1932 and was purchased by the American Zinc Co. in 1940. Because of the condition of the equipment, excepting the motor generator set, a complete rebuilding was necessary. The Fairmont City plant of the American Zinc Co. could treat the leach residues, the purification cake and the skimmings from the melting furnace in its various plants. This possibility permitted a simple flowsheet with good economic results. The flowsheet is shown in Fig. I. The calcined concentrates are leached in mechanically agitated tanks with spent electrolyte and such ferric iron solution as necessary. When the acid has been neutralized and the iron coagulated, the fluid is discharged to settling tanks. The underflow from these thickeners is filtered on a Moore filter; the filter cake leaves the plant for retreatment and the filtrate joins the thickener overflow. Zinc dust is added to this solution until the copper and cadmium are precipitated. The pulp is filtered through Shriver presses, which deliver the purified solution to storage tanks, and the copper-cadmium-zinc cake is shipped for retreatment and recovery of these three metals. The purified solution is electrolyzed; the regenerated acid is returned for use in the leaching plant and the cathode zinc, after stripping, goes to the melting furnace, from which it is cast in slabs. The skimmings from the melting furnace are shipped to the Fairmont City plant for reduction to metal in the retort furnaces. The choice of this simple flowsheet was made possible only because of the facilities of the Fairmont City plant. The long leaching period, with high acid content and high temperature which characterize the high-density process, gives a higher zinc extraction but also dissolves more impurities, which must be removed. The same is true to a lesser degree of the multi-step leaching of the western low-density plants. By the sacrifice of some initial extraction, solutions can be obtained that are relatively easy to purify and give good ampere efficiency. This loss in initial extraction is made up in the retreatment of the residues in the Waelz plant. The impurities that accompany the zinc thus extracted are inconsequential when the Waelz product is treated in a distillation plant. It was recognized that this flowsheet would require a somewhat greater amount of sulphuric acid-either as acid or as sulphate sulphur in the calcine-because of poorer washing. The sulphuric acid plant at Fairmont City could deliver 60° Bé. acid to compensate for the sulphate loss and the cost would be less than the cost of more intensive washing.

Jan 1, 1942

By L. P. Davidson

The new electrolytic zinc plant of the American Zinc Company of Illinois commenced operation in April 1941. The simple flowsheet using the standard current density and the economic reasons that dictated it are given herewith. The Evans-Wallower Zinc Co. built an electrolytic zinc plant at Monsanto, 111., in 1929 and operated it for about two years. The plant stood idle from 1932 and was purchased by the American Zinc Co. in 1940. Because of the condition of the , equipment, excepting the motor generator set, a complete rebuilding was necessary. The Fairmont City plant of the American Zinc Co. could treat the leach residues, the purification cake and the skimmings from the melting furnace in its various plants. This possibility permitted a simple flowsheet with good economic results. The flowsheet is shown in Fig. I. The calcined concentrates are leached in mechanically agitated tanks with spent electrolyte and such ferric iron solution as necessary. When the acid has been neutralized and the iron coagulated, the fluid is discharged to settling tanks. The underflow from these thickeners is filtered on a Moore filter; the filter cake leaves the plant for retreatment and the filtrate joins the thickener overflow. Zinc dust is added to this solution until the copper and cadmium are precipitated. The pulp is filtered through shriver presses, which deliver the purified solution to stor- age tanks, and the copper-cadmium-zinc cake is shipped for retreatment snd recovery of these three metals. The purified solution is electrolyzed; the regenerated acid is returned for use in the leaching plant and the cathode zinc, after stripping, goes to the melting furnace, from which it is cast in slabs. The skimmings from the melting furnace are shipped to the Fairmont City plant for reduction to metal in the retort furnaces. The choice of this simple flowsheet was made possible only because of the facilities of the Fairmont City plant. The long leaching period, with high acid content and high temperature which characterize the high-density process, gives a higher zinc extraction but also dissolves more impurities, which must be removed. The same is true to a lesser degree of the multi-step leaching of the western low-density plants. By the sacrifice of some initial extraction, solutid'ns can be obtained that are relatively easy to purify and give good ampere efficiency. This loss in initial extraction is made up in the retreatment of the residues in the Waelz plant. The impurities that accompany the zinc thus extracted are inconsequential when the Waelz product is treated in a distillation plant. It was recognized that this flowsheet would require a somewhat greater amount of sulphuric acid—either as acid or as sulphate sulphur in the calcine—because of poorer washing. The sulphuric acid plant at Fairmont City could deliver 60" BC. acid to compensate for the sulphate loss and the cost would be less than the cost of more intensive washing.

Jan 1, 1944