Search Documents

"Polycom, a new approach to ore processing based on pressure comminution, is obviously a very attractive alternative to conventional processing methods.Since a full-scale pilot plant was commissioned in 1986, more than 125 commercial installations, with capacities up to 1000 t/hr, have gone ahead.Already successfully used in processing cement clinker, limestone, coal, and other minerals, Polycom high pressure grinding results in:o Significantly reduced capital costs, because smaller units can be used m new installations;o Capacity increases of up to 100% in existing facilities; and o Operating economies that include energy savings of 20% or more, and reduced wear parts consumption.1. IntroductionAutogenous or semi-autogenous mills in conjunction with rod or ball mills are used with preference for ore processing. Most ball mills are of closed-circuit design and operate with mechanical classifiers (spiral or rake classifiers) or hydrocyclones. In other words, the ores undergo wet primary grinding, since slurries are required for the downstream separation stages anyway. This paper presents a new grinding system based on high pressure comminution of ores. This grinding process allows:- Energy savings of up to 20 % or more- Capacity increases of up to 100 % and more- Reduction of wear costs- Smaller units for new installation and thus- Reduced investment costsThese advantages are highly interesting for both new installations and conversion projects, particulary in cases where an increasing hardeness of the ore, i.e. rising Bond Work Index, reduces the output of the plants or where the metal assay of the ore decreases and the capacity of the existing systems has to be increased. POLYCOM high-pressure grinding rolls have established themselves with great success already for grinding cement clinker, granulated blast furnace slag, limestone, cement raw materials, coal and other materials.Meanwhile more than 250 high pressure grinding rolls have been installed worldwide. Capacities up to 1.000 t/h with roller diameter up to 2.8 m and drive units up to 2.400 kW are installed."

Jan 1, 1991

By L. Y. Sadler

This report summarizes the findings of a 9-yr research program, sponsored by the U.S. Department of Energy and conducted by the Bureau of Mines, to evaluate refractory liner materials for coal gasifier reactors. Commercially available refractories were exposed to coal gasifier reactor environments, reproduced in the laboratory with a high-temperature, high-pressure test facility, followed by extensive postexposure evaluation. Thirty-six castable or gunnable refractories and cements and 24 refractory brick were evaluated. The behavior of castable refractories reinforced with stainless steel fibers was also examined. Gas environments that were evaluated included steam, H2, CO2, CO, and typical high-and low-Btu gas mixtures. Exposure pressures ranged from 100 to 1,000 psig, temperatures from 5000 to 1,1000 C, for periods from 50 h to 2,000 h. In some exposures, sodium and/or potassium hydroxide were introduced in order to simulate a high-alkali environment. It was found that intermediate-and low-alumina refractories produced from domestically available raw materials, rather than high-alumina refractories produced from imported raw materials, gave the best service as liner materials and that alkali attack was probably not a serious problem with most refractories. Based on the results of this program, good choices of refractory liner materials for gasifier reactors can be made.

Jan 1, 1984

By Stephen Tadolini

A unique circumstance created by monitoring a pre-driven longwall recovery room permitted measuring the stresses of a coal pillar throughout its entire life cycle in less than a week. A fender pillar, created in approximately the middle of a longwall panel at a depth of 650 ft, transformed from a solid barrier pillar - to a yielding pillar - to a residual pillar as 3 ft slices were methodically removed with the longwall shearer. The complete transformation, or life cycle, took place in less than 12 hours. The stresses were quickly transferred from the pillar onto the standing pumpable concrete supports and into the outby pillars. Roof to floor closure measurements, combined with the timing of the pillar behavior, provides a detailed look at the uncontrollable convergence of underground mine openings. Pillars remain the most important form of ?primary support? and understanding these life cycles is vital for safe and efficient mine design, in both room and pillar and longwall panel extractions.

Jan 1, 2007

Background ArcelorMittal?s (formerly QCM?s) Port Cartier iron ore pelletization operations 2 side-by-side induration furnaces each producing 578 t/h of cured pellets Firing No. 6 fuel oil and coke breeze (in bed) Very large heat losses to be addressed primarily by gas recirculation

May 1, 2011

By M. P. Brungs, S. Haji Amini

Static dissolution of CaO into a CaO-SiO2-Al2O3slag and slags with additional fluxing agents (fluorspar, nepheline syenite and ilmenite) was studied. The slag was packed into dense CaO crucibles and heated to 1500ºC /1600ºC. After reaction, the crucible was air cooled and cross-sectioned. The development of the Ca2SiO4 phase and concentration profiles of various cations across the reaction zone were examined by Electron Probe Micro Analysis. At 1500ºC, a Ca2SiO4layer was found to form at the CaO/slag interface. No such layer was evident at 1600ºC. Ilmenite and nepheline syenite were found to be effective substitutes for fluorspar, increasing the rate of CaO dissolution.

Jan 1, 2004

Perception has the unfortunate habit of becoming reality. Urban inhabitants unfortunately do not regard mining as a legitimate or desirable business, despite its contribution to Australia's export income (+A $8,000 million, being nearly a third of all exports); share of GDP (it is 4.5%); and the fact that its presence fills up all the empty spaces northwest of the Adelaide-Melbourne-Sydney-Brisbane crescent of inhabitation. The huge economic contribution of Australia's minerals industry, resulting from providing more than half of merchandise exports (Figure 1), is achieved by employing only some 2% of the national work force (Gaulton, 1997). Unfortunately, the minerals industry's critics generally oppose exploration on the basis that what you don't know will not hurt you. It is the 'do-not-confuse-me-with-facts' philosophy or 'ostrich syndrome', which somehow crudely assumes that mining practices have stayed in the style popular circa late 1800s. Somehow ignorance really is bliss for these idealistic believers, who are reminiscent of the members of the Flat Earth Society!

Jan 1, 1997

By T. Nyakudarika

The Unki Platinum Mines concentrator, employing an MF2 circuit configuration which includes fully-autogenous primary milling of run-of-mine (ROM) ore, was commissioned in November 2010. The project was Anglo American Platinum?s first PGM concentrator in Zimbabwe and would form a significant contribution to the group?s platinum production. The project financials demonstrated that the project was operating-cost sensitive. After reviewing the metallurgical testwork, mineralogical examinations, and the history of similar operations, it became apparent that the Unki ore characteristics rendered it amenable to autogenous milling. The primary ball mill, structurally designed for 30 per cent steel load, could be operated at the required initial phase throughput with fully-autogenous primary milling, realizing savings in both power requirements and grinding media consumption. The original mill sizing had been done with fully-autogenous milling in mind, but allowing for flexibility and mitigation in case of varied mining fragmentation. Since attaining steady state, target grinds have been achieved. This paper looks at the Unki ore characterization programme, design considerations, and the operational and control philosophy for a successful comminution circuit, and discusses the design to produce a flexible, low opex, mitigated comminution and overall MF2 flowsheet that is easily expanded in line with the potential for optimum exploitation of the orebody.

Jan 1, 2012

Study on Pure Mineral Flotation Tests of Low-Grade Phosphate Ore in Zhijin, Guizhou Province, China

Sep 13, 2010

By Y. D. Lee, J. H. Park, D. S. Kim, H. S. Song

The viscosities and the infrared spectra of the CaO-SiO2-MgO-CaF2(or Al2O3) slags were measured to enhance our understanding of the interrelationship among the thermophysical property, microscopic structure, and chemical thermodynamics of molten slags. The structural role of CaF2and Al2O3in the calcium silicate melts can be explained by a change of the degree of polymerization (DOP). The effect of CaF2on the viscous flow of molten slags is based on a decrease in the DOP by F-as well as by O2-ions and this was confirmed by the infrared (IR)spectra of the quenched slags. The effect of Al2O3on viscosity increase can be understood from an increase in the DOP by the incorporation of the [AlO4]-tetrahedra into the [SiO4]-tetrahedral units and this was also confirmed by the IR spectra. An amphoteric behaviour of Al2O3in the aluminosilicate melts could be correlated to the effect of ionic species of alumina, that is [AlO4]-tetrahedra and [AlO6]-octahedra, on the stability of silicate polyanions by taking the activity coefficients of slag components into account. Keywords: viscosity; infrared spectra; degree of polymerization; amphoteric behaviour; stability; activity coefficient

Jan 1, 2004

By J Merrells

Fluor, together with our clients, has yielded significant reductions in the total cost of mining projects by employing a systematic and methodical process of cost reduction. This paper outlines this structured approach to reducing the total cost of projects through the gathering of information, the evaluation of the zero base design, and the development of the execution strategy for the project in the study phase.Over the recent iron ore boom the cost of growth projects escalated rapidly due to a variety of factors including the engineering cost of re-designing facilities, construction in remote areas and an increase in the ‘perceived’ capital requirements for maintainable and operable facilities.Fluor has made strategic steps towards safely reducing the capital intensity of projects, by working with clients to develop zero base designs which utilise the minimum technical requirements in order to meet the function of the plant and then add cost for safety, maintenance and operability only where clearly justified.This paper has set forth a structured three phased approach to focus the team on reducing capital cost while maintaining a low increase in engineering effort.The initial ‘gather’ phase focuses the team on acquiring information and identifying decisions that will need to be made so that the team can prioritise and focus the attention on areas that will provide the greatest benefit. Within this phase the identification of zero base design requirements, review of lessons learnt and analysis of capital cost levers, allows the team to identify the key decisions on the project that will affect the capital cost.In the subsequent ‘evaluation’ phase the team established the zero base design, using the hierarchy of cost reduction as a guide to focusing the team’s attention on high yielding cost saving opportunities.In the final phase the team develops the execution strategy which will yield the least cost using strategies and tools such as modularisation, standardisation, replication, strategic sourcing and 3D design.CITATION:Merrells, J, 2017. Reducing total project cost in the study phase using zero base design, in Proceedings Iron Ore 2017, pp 621–626 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Paul Doherty

Expansion of the global piling industry has been coupled with significant research efforts investigating the mechanisms controlling pile capacity. Static pile design has transitioned from total stress approaches toward effective stress design, with associated improvements in predicting pile performance. As a result, the available literature is heavily skewed toward static capacity prediction. However, when considering piles offshore, the majority of loading is not static but highly variable and cyclic in nature. This paper outlines the additional factors that require consideration for cyclic pile design, including elevated loading rates, cyclic displacements and capacity degradation. A review of the literature identified a number of cyclic pile testing programs which are collated in this paper. General trends are established through comparison of the tests within the database and the conditions where cyclic loading is most likely to be a concern are identified. In particular, loading conditions which involve full plastic shear reversals are seen to cause the most extreme cyclic damage, with the degraded capacity as low as 31% of the precyclic static capacity. The underlying mechanisms which can result in cyclic damage are explored, with particular attention given to the pore pressure response, radial stresses, shear transfer and particle reorientation.

Jan 1, 2009

By S. Ersayin

In 1998, the Concentrator Modeling Center was established within the Coleraine Minerals Research Lab, Coleraine, Minnesota, to develop models for simulation of iron ore processing plants, and to assist plant operators in improving performance of their aging plants. The short-term objective was to develop necessary models for reliable simulation using conventional techniques, while the long-term objective was set as liberation-based modeling and simulation of these plants. The short-term objective was achieved in 2002 after the development of models for magnetic separators, hydro-separators and fine screens. A project funded by the U.S. Department of Energy was carried out to demonstrate the capability in improving iron ore processing at the Minorca plant. As a result of this study, a 10% improvement in throughput at the plant was obtained, and simulation became a desired tool for plant operators. A significant step in the long-term objective was reached in 2005 with the development of a liberation model. This was followed by incorporation of models capable of processing liberation data into the software. By early 2007, the Concentrator Modeling Center had the capability of performing liberation-based simulation of entire plants.

Jan 1, 2009

By George K. Burke

Underpinning of a structure has been traditionally expensive, time consuming, and, in many cases, caused as much settlement to the existing structure as it was trying to prevent. As underpinning is normally one of the initial tasks and on the critical path on a construction project, there is immense pressure on the subcontractor to speed up his operation so the new structure can proceed; this can cause an adversarial relationship to develop between the owner, engineers, general contractor and subcontractor. Since its introduction to the North American market in the late 1980's, Jet Grouting has not solved all these problems, but where utilized, has shown economical benefits, a faster and safer installation, and a minimal movement of the structures being underpinned. A history of the development of jet grouting is presented; a comparison of this technique versus other grouting methods, a description of the jet grouting system with emphasis on the triple rod systems; case histories of jet grouting used for underpinning and conclusions and references are included to follow the program's themes of: - Recognizing Solutions to Today's Problems - Defining Tomorrows Challenges - Putting America on a Solid Foundation

Jan 1, 1991

By R. A. Cattell

The peacetime activities of the Bureau's petroleum and natural-gas program have been reoriented to serve the needs of a national-defense program. When the United Nations sent troops to Korea after the North Korean Army crossed the 38th parallel in the latter part of June 1950, the Bureau's coordinated national program on petroleum and natural gas, with each major project forming an essential member of its framework, was carefully reviewed by those in charge of the work. As a matter of fact, the era of normalcy in which the petroleum and natural-gas research of the Bureau of Mines prospered during the fiscal year 19502/ was no sedative to the need for alertness on a national-defense front. The program, although conducted along peacetime lines in general, was scanned critically and repeatedly during that period to see where - if the need should arise -the emphasis could be shifted from peace to defense or war. Judging from the experience of two wars, it would not be long before the Bureau would be asked to use its trained technical personnel in applying techniques already learned in peacetime research to the requirements of munition and fuel needs of national defense. Near the end of January 1951, petroleum and natural-gas engineers of the Bureau of Mines began a comprehensive study of reservoir conditions in the Canyon Reef fields of Scurry, Borden, and Kent Counties, Tex. This work was preceded by published analyses of crude oils from Scurry County as early as April 1950. Well-informed persons in industry have estimated that these fields hold reserves that will yield 3 to 6 billion barrels of stock-tank oil. Although generally accepted good operating practices have been followed, engineering tests have shown that the natural energy, except in some favorable parts of the reservoir, will not be adequate for obtaining a high percentage of recovery. Correct information regarding the extent and availability of this vast reservoir of hydrocarbons is therefore of great concern to the Petroleum Administration for Defense in carrying out its responsibilities under the Defense Production Act.

Jan 1, 1952

By Chee Theng

"Mineral processors know you can put in the best technology in the world but it won’t work optimally without the support of the operators. Conversely, you may have complete operator support but won’t get top results without the right technology. When the two come together, the returns can be phenomenal.The first day of talks at the 68th Annual Colorado MPD Conference, held April 26-28 at The Broadmoor in Colorado Springs, covered the ground on these industry wisdoms.Coming together as a team“Think of the people, not just the lab and the numbers. That makes all the difference,” said Dee Kippers, of FMI Henderson Mine, in her talk on “Process optimization during a market downturn (A Moly MacGyver story).” Kippers told an entertaining story of the journey she and her team took in tackling the issue of an annual spike in iron content in the product at Freeport- McMoRan’s Henderson primary molybdenum mine near Empire, CO.As the metallurgists tried one thing after another — cranking up the iron depressant, adjusting pH with sodium hydroxide and hydrated lime, modifying reagent levels — Kippers found that when she shared her results with the operators, communicated with them on what she was doing and got their input, they were more willing to work with her, and more understanding and supportive of her efforts.The results make the case for getting people on board and coming together as a team. The cost savings from their optimization efforts, with little capital investment, have been “enough to cover the annual salaries of our metallurgy department and then some,” Kippers said.Considering the environmentDavid Lemieux, of Dundee Sustainable Technologies (DST), talked next on “Cyanidefree process for gold extraction,” presenting the results obtained from a demonstration campaign of the company’s novel chlorination process for gold extraction and associated arsenic stabilization process. Developed at an investment cost of C$35 million, they are ready for commercialization, having been demonstrated on the laboratory, pilot and demonstration scales.The DST process is differentiated from the Plattner chlorination process, which was in use from 1851 to 1916, by moderate process conditions of atmospheric pressure and ambient temperature — the result of using sodium hypochlorite solution, or bleach, instead of direct injection of chlorine gas — and new, cheaper materials of construction, such as polymers, plastics, fiberreinforced plastics and Teflon, resulting in lower capital and operating expenditures."

Jan 7, 2018

By J. S. Ross

The significance and role of industrial minerals in Canada differ from those in the United States, The smaller Canadian industry has recently become well diversified and self-sufficient in most commodities, However, it depends on exports, principally to the United States, for much of its market, Imports are small, but imports of several basic products manufactured from industrial minerals are large. This nation is a leading world producer of asbestos, gypsum, sulphur, nepheline syenite, titania slag, potash and barite. It has reserves in asbestos for at least 30 years enough potash to supply the current world's needs for 2,000 years and sulphur reserves for 40 years of current world demand, One of the ilmenite deposits contains enough titania to supply the current world demand for at least, 25 years.

Jan 1, 1964

By Gerard de Vries

pipeline industry and are still growing in size. Liquid epoxy and polyurethanes are an excellent choice for whatever the aggressiveness of the substance transported and whatever the harmful outside influences, maximum protection is required. They can be used as coatings on all kind of pipelines varying from the mainline coating to the field joint coating. Compared with traditional systems like dual layer FBE and 3-layer polyolefin there are some benefits to be considered like easiness of repairs, amount of coats, application temperature and film thickness. The interior coating renders the pipe surface so much smoother that considerable savings can be realized in pump stations. Apart from the interior of the pipeline, the industry is faced with new challenges like higher operating temperatures of lines and an emphasis on product benefits in order to save money. Key words: liquid epoxy, liquid polyurethane, phenolic epoxy, pipeline, field joint coating, internal coating, corrosion control

Jan 1, 2006

By F. Dinter, C. McGregor, Q. G. Reynolds, L. Hockaday

The necessity of reducing greenhouse gas emissions to limit the impact of anthropogenic climate change means that all industrial processes should investigate their options towards decarbonization. Iron, steelmaking, aluminium, and cement production produce the most industrial emissions. Although most research focuses on decarbonizing these industries, minerals processing industries must be decarbonized to achieve net zero emissions goals by 2050. Incorporating renewable energy sources and avoiding the combustion of fossil fuels are two ways to reduce greenhouse gas emissions. This paper reports on the results from a dynamic process model developed to investigate the feasibility of concentrating solar thermal pretreatment of manganese ores to pretreat carbonate-rich manganese ores for increased ferromanganese smelter productivity and reduced greenhouse gas emissions. The results indicate that pretreated ores reduce the energy requirement for smelting significantly for some ores and lowers total carbon dioxide emissions by 13 to 19% compared to the traditional smelting route. A high-level economic evaluation shows that solar thermal treatment is financially viable for low cryptomelane, high braunite ore that is common in the Kalahari Manganese Field.

Dec 11, 2024

By S. A. Hovanessian

The method of characteristics which reduces the Buckley-Leverett mnlineur, partial differential equation to two first-order, linear differential equations is applied to the solution of a waterffood recovery problem for multiple lines of producing wells and one line of injection wells. The application of the method is described by a numerical example, and a brief theoretical background is given. From the results of this study, it is concluded that the cumulative water injected and oil produced are the same for single and multiple sets of producing wells. INTRODUCTION In this paper, the method of characteristics is applied to the solution of a waterflood recovery problem with multiple lines of producing wells and one line of injection wells. The application of the method to this type of recovery problem considerably simplifies the procedure of obtaining a numerical solution. It differs from the method described by Kern1 because it eliminates the need for integration in obtaining saturation fronts. In addition, the saturation history at any location within the field is obtained from a single diagram (time vs distance with saturation as a parameter)'. The paper includes a brief theory of the method of characteristics and its application to the solution of oil recovery problems. A numerical example is worked out, and the cumulative oil recovery-vs-time curve for a system with multiple sets of producing wells is obtained. This curve is then compared with the recovery curve of a system with only one set of producing wells. From this study, it is concluded that the cumulative water injected and oil produced are the same for single and multiple lines of producing wells. However, the recovery time is considerably longer for multiple sets of producing wells.

By D Garcés, M Meléndez, R Castro, E Viera

Enhancing the understanding of gravity flow in caving operations is a key factor in the design, operation and success of caving methods. Consequently, much research has been performed to increase knowledge about gravity flow. Many valuable theories have been gained from different research approaches, which include physical modelling, numerical modelling and a limited number of full-scale tests. Recent advances in technology have allowed Codelco Chile to carry out trials using Smart Markers technology. This technology was used in Esmeralda mine’s Block-2 at El Teniente mine from August 2012 to January 2015. This paper aims to determine the characteristics of the extraction zone and obtain the data that will allow greater understanding of gravity flow for design and draw control purposes.The collected data from recovered markers were analysed using a linear interpolation of both the initial position of the markers and drawbell accumulated drawn tonnage. For each drawpoint in the trial, the regularity or irregularity of flow was analysed based on the recovered markers and the drawn tonnage. Correspondingly, the relationship between flow characteristics and observed fragmentation in drawpoints was analysed. The gravity flow of the Smart Markers revealed that current drawpoint spacing provides the interaction conditions of adjacent flow zones. However, it is possible to increase the drawpoint spacing while allowing caved rock to be extracted from the major and minor apexes.The results of this research also verified that full-scale test data are the predominant factor in the production level design and production control at El Teniente mine.CITATION:Garcés, D, Viera, E, Castro, R and Meléndez, M, 2016. Gravity flow full-scale tests at Esmeralda Mine’s Block-2, El Teniente, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 349–358 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016