Search Documents

By William X. Chavez

The Mantos Blancos copper-silver district, a major copper-producing area since 1961, is located on the Tropic of Capricorn about 45 kilometers northeast of the northern Chile port city of Antofagasta, as shown in Figure 1. Copper oxide minerals occurring as atacamite (Cu C1(OH)3) and chrysocolla (copper silicate-hydrate) were discovered in the district in the early 1900's (Knobler and Joseph, 1962). The mine is situated in the northern Atacama Desert, one of the most arid regions on earth, and presently receives less than 1 cm per year of precipitation. The extreme aridity of the Atacama Desert is thought to have prevailed since at least Middle Miocene time (Mortimer et al., 1978) when development of important supervene copper enrichment was slowed in many areas of northern Chile (e.g., Chuquicamata, Exotica). Despite the paucity of precipitation, landform development is mature, with large alluvial fans and alluvial-filled valleys covering much of the region. In addition, the aridity and presence of salts have led to the formation of a sub-surface cementing of alluvium and colluvium by halite-rich caliche ranging from a few centimeters to over 3 meters in thickness. These factors, resulting in poor outcrop exposure, make even reconnaissance mapping difficult.

Jan 1, 1983

By Robert Stefanko

The concept of disposing of liquid industrial wastes by deep-well injection is not a new one. Brines associated with crude oil long have been disposed of in this manner, with the additional benefit of aiding secondary oil recovery. More recently, with the expansion of nuclear energy, the lethal, highly radioactive wastes which are by-products of the fission process have created severe disposal problems. During the past ten years, a variety of industries have resorted to subsurface disposal, some of the details of which are given elsewhere (1,2). The list reveals wide variations in injection rate, pumping pressure, cost, and waste disposition. Included are successful installations in Western Pennsylvania.

Jan 1, 1969

By Elio Ferreira

This report describes the design, and development work performed to reduce the volume and weight of the miners caplamp battery, as well as a headpiece with a swivel mechanism containing a halogen bulb with two filaments. Work was also conducted in the development of a maintenance free battery. The design concept is based on non-sintered Ni-Cd technology, with an energy density of 22 Wh/lb. The cap lamp system developed has been approved by the Mine Safety and Health Administration (MSHA) and can be manufactured for mine use.

Jan 1, 1988

By R Markoski, P Grealish

The requirement for rapid vertical development for underground ventilation is often a factor when dealing with dynamic mine plans, with short vertical developments being used to optimise ventilation systems. In an effort to increase the safety and efficiency of the constructions, a simple and effective sinking methodology is required that is both adaptable and repeatable. A modified shaft construction methodology is proposed that attempts to minimise risk to the personnel as well as be cost-effective. Readily available equipment is used to ensure adaptability to the various environments and shaft parameters.One of the greatest risks of shaft sinking is having personnel working suspended over open cavities or underneath suspended loads. Removing this risk, by ensuring all construction is done from solid ground, allows for safer sinking operations. As the process is repeatable, familiarity and confidence in its construction sequence will increase with each successive sink.A trial sink is performed with a 3.6 m diameter, 20 m deep shaft. The shaft was excavated using a conventional strip-and-line philosophy, with the shaft then being lined from the collar via the use of large diameter corrugated steel culverts. The annulus between the steel culverts and shaft excavation is then filled with a concrete mixture to secure it in position.The new process was successful, with no personnel at any time during the process being suspended above an open excavation. The installation had relatively low capital and operational costs and was completed faster than an equivalent, conventional concrete-lined shaft construction. Therefore when compared to conventional shaft-sinking methods, this process can be considered safer, more efficient and relatively cost-effective.Further research is required to determine whether this method can be expanded to larger vertical developments.CITATION:Markoski, R and Grealish, P, 2014. A new method for rapid vertical development of underground ventilation shafts, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 603–606 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Stephen E. Stewart

This document presents the explosion-proof enclosures used severity of certification tests solutions to linear transient thermal and stress analyses of in underground mines. The results were used to assess the for enclosure windows relative to possible loads occurring in the actual mine environment. Cast iron electric light enclosures with polycarbonate and glass windows were analyzed under steady state thermal conditions (light burning) and for thermal shocks corresponding to an internal explosion (ignition of volatile mine gas) or external quenching (mine water spray system). Thermal shocks to the enclosure, caused by ignited gases or water spray, were applied via a series of load steps in the transient analysis. The temperature dependence of material I properties and of the film heat transfer coefficients were included in the model. The work demonstrates that thermally induced stresses are strongly influenced by the way the window is mounted in the enclosure. It also shows that the MSHA Thermal Shock Test, if performed on an unsupported lens (or window), produces lower stresses than the lens (or window) may experience in the mine environment.

Jan 1, 1984

By Rolland R. Mates

This paper describes the use of post- tensioned rock anchors to reduce the risk of future damage to a residential structure as a result of coal mine subsidence. The project described in this paper was performed by the Office of Surface Mining Reclamation and Enforcement (OSMRE) of the U. S. Department of the Interior. The OSMRE was created to administer Public Law 95-87, the Surface Mining Control and Reclamation Act of 1977. The responsibilities of OSMRE include "reclamation and restoration of land and water resources, adversely affected by past coal mining including prevention, abatement, control of coal mine subsidence. ?('l) Consequently, OSMRE has been addressing mine subsidence problems since its initial subsidence stabilization project in 1979. Stabilization activities have primarily consisted of supporting the overburden material by injecting materials through drilled bore holes into the underground mine voids. Injection of various materials into mine voids, including fly ash mixtures, coal refuse, cement grout, and gravel has proven to be a successful method of reducing mine subsidence-related surface movements, and has been extensively utilized in mitigating mine subsidence problems. However, the cost of drilling for injection can be extremely high in areas where the depth to the coal seam is great.

Jan 1, 1986

By Wilbur S. Burbank, Robert G. Leudke

The impressive western San Juan Mountains of Colorado were carved by Pleistocene and Recent erosion from a thick blanket of Tertiary volcanic rocks that rests upon a basement of metamorphic, sedimentary, and igneous rocks ranging in age from Precambrian to Tertiary. These rocks record a long, complex, and fairly complete sequence of geologic events that have affected the region through much of geologic time. The geologic history of the region includes several periods of deformation, erosion, and igneous activity; closely associated with two of these periods were two periods of mineralization. The older of these was related to Late Cretaceous-early Tertiary (Laramide) intrusive activity, and its deposits occur in the older sedimentary units. The younger, of later Tertiary age and related to the widespread middle Tertiary extrusive and intrusive activity, is the chief concern of this paper. Tertiary volcanism built a great plateau surrounding the San Juan volcanic depression, a complex of subsided crustal blocks in the vent areas. The Silverton and Lake City cauldrons, nested within the larger depression, were domed by resurgent magma that created keystone grabens along the distended crests of the domed floors and many postcauldron radial and concentric fractures, dikes, and intrusive plutons within and marginal to the cauldron sites. The postvolcanic evolution of large quantities of gases, chiefly carbon dioxide and water, propylitically altered the rocks in and around the volcanic depression prior to the younger period of ore deposition. The ore deposits, localized mainly in the radial and concentric fractures about the cauldrons and in the associated graben faults, include fissure veins, chimneys, replacements, and disseminations in volcanic and underlying basement rocks. Fissure veins, constituting the major economic source, yielded precious- and basemetal ores. Most veins are compound with sphalerite, galena, and chalcopyrite; some veins contain silver-bearing arsenical sulfosalts and free gold. These minerals occur in predominantly quartz gangue. However, gangues composed of several manganese silicates and carbonates and relatively· barren of metals are abundant locally and probably originated by alteration of rocks at roots of faults and fissures during evolution of carbonatic solutions. The bulk of the ores are hypogene and probably had their source in deep parent magmas of the shallow eruptive rocks. Total production since the early 1870's has exceeded half a billion dollars in recovered metals, with a ratio of precious- to base-metal values of about 3 to 2. Since 1930, improvements in metallurgical treatment and mining techniques have increased the base-metal yield.

Jan 1, 1968

By David White

Jan 1, 1925

By S. H. Ward

An account of a new method of investigating the electrical .properties J the earth's crust is presented. The method, called AFMAG, employs, as a source, natural alternating magnetic fields of audio and sub-audio frequencies. Measurements of the distortion of these fields caused by geological features are made with the aid of search coil detectors at several discrete frequencies. Many results of field surveys made with the method are presented and they illustrate its advantages and limitations when applied to the search for massive sulphide mineralization. The advantages far outweigh the limitations and in fact indicate that a major breakthrough in geophysical exploration technique and instrumentation has been made.

Jan 1, 1958

By T. G. Hawkins, T. M. Naciuk

"The Katie Cu-Au deposit is situated in southeastern British Columbia, 425 km east of Vancouver. The deposit is a member of the alkaline group of porphyry Cu-Au deposits associated with potassically and propylitically altered andesitic volcanic rocks.The Katie porphyry system occurs in mafic to intermediate alkaline volcanic rocks of the Lower Jurassic Elise Formation of the Ross/and Group. Host metavolcanic rocks include andesitic to basaltic flows, flow breccia, massive fine tuff and crystal tuff Gabbroic intrusions alternate with the volcanic rocks in drill core. The lack of chilled margins and shear contacts, as well as their similar composition to the volcanic rocks, suggest that the gabbro was synvolcanic.Alteration exhibits a zonal pattern spatially related to zoned porphyry-style mineralization. Propylitic alteration is common and assemblages consist of epidote, chlorite, sericite and calcite. Potassic alteration zones are accompanied by elevated copper-gold grades and are composed of K-feldspar, plagioclase, quartz, biotite and chlorite. Narrow drillhole intervals of secondary magnetite, generally less than 2 m across, occur above the potassic alteration zones. A thick oxidized cap lies above the mineralized zones, although only local supergene enrichment has been identified. The lack of supergene enrichment is perhaps due to intense near-surface fracturing and leaching from a high energy groundwater environment.Sulphide mineralization consists mainly of pyrite within the propylitic halo, and pyrite and chalcopyrite with trace pyrrhotite, sphalerite, tetrahedrite, bornite and molybdenite within the potassic alteration core. Malachite, azurite and traces of chalcocite occur within the oxidized cap.Discovery and exploration techniques have included airborne geophysics, regional stream sediment sampling, prospecting, geological mapping, ground geophysical surveys, soil sampling surveys, and diamond drilling. Two primary targets of porphyry copper-gold mineralization have been identified by exploration. The Main zone strikes northwest, has an apparent true thickness ranging from 70 m to 135 m, and is a minimum of 500 m in length. The 17 zone strikes northwest, has an apparent true thickness of 90 m, and is a minimum of 300 m in length. The two zones are defined by grades that generally exceed 0.2% Cu and 0.25 g/t Au. Both zones are open along strike and to depth."

Jan 1, 1995

By T. Hart

Nuclear gauging is used world-wide in almost every industry. From mining and ore-grading to finished product, the metallurgical industry is one of the biggest users of nuclear sensors for inventory, process control, and quality assurance. This paper will discuss the basic theory of gamma transmission gauging techniques found useful in mining, milling and metal production. Techniques to be discussed are gamma transmission for level and density. A major new technique will also be discussed. This technique is called gamma backscatter. The uniqueness of this technology, how to apply and the differences between transmission and backscatter will be accentuated.

Jan 1, 2011

By Nikolaos Polysos, Holger Witthaus

INTRODUCTION The classification system for German coal mining is the result of approximately 100 years of experience in roadway development and longwall mining. It is also based on different research projects covered by national and European research programs. Over the past 30 years, more then 600,000 m of road-ways have been driven and employed for mining activities. To properly describe the German rock mass classification system, therefore, it is useful to take a look at the main geomechanical preferences and common support systems. The decision about the most effective development technique and support system is based on a synthesis of rock mass classification and geomechanical analysis. The properties of surrounding rock, the in situ stress, and the influence of mining activities in several seams at each German mine must be considered for the evaluation of the expected deformation of the roadway. The mine layout, the requirements of ventilation and fire prevention, as well as the need to maintain emergency escape routes for the miners, require that the gate roads remain usable after the passage of the longwall face in most cases. Moreover, the gate roads must be maintained despite the high stresses that are applied during longwall retreat mining. Therefore, gate road design must address a broad spectrum of potential deformation environments. In the past, when gate roads were supported solely with yielding steel arches, lithologic descriptions of the surrounding strata conditions were adequate for the dimensioning of support and the prediction of the roadway deformation. The current conditions of multiple-seam mining at depths of up to 1,700 m require combined support systems, including pattern bolting and backfilled steel arches. Rock bolt support is used for development, after which (typically 50–100 m outby the face) the steel arches are installed and backfilled with building material (concrete) in order to achieve an optimized development rate. The rock mass classification system described below was developed especially for the conditions of German hard-coal mining. It includes the stress distribution caused by multiseam workings (including crossing goaf edges of former longwalls), as well as in situ stresses due to greatdepth and the presence of tectonic faults. It is based on the evaluation of four parameters: • Geotechnical analysis of drill cores • Geotechnical observation of the development face • Geotechnical classification of tectonic structures (faults) • Standard classification derived from geotechnical assessment and evaluation of stress conditions (using numerical modeling for stress calculation) ROCK STRENGTH One of the most important input parameters for describing strata conditions is the strength of the rock. The German classification system is based on a description of lithotypes. This method has been used successfully since the 1950s and is based mainly on the uniaxial compressive strength (UCS) of the material. An evaluation of the rock strength observed in a survey of approximately 82,500 samples of rock core yielded the results shown in Figure 1. The three most common coal measure rock types are mudstone, siltstone, and sandstone. Each shows a specific mean UCS level and a different spread between the minimum and maximum values. Sandstones, in particular, have a wide spectrum of compressive strength, ranging from approximately 40 MPa to greater than 130 MPa, with an average of 85 MPa. The causes of this wide range include different sedimento-logical preconditions, facies, and digenetic processes. [ ]

Jan 5, 2007

By Robert C. Dyni

This U.S. Bureau of Mines (USBM) report summarizes a field demonstration of pneumatic backfilling technologies conducted at the abandoned Hillside Coal and Iron Slope in Vandling, P A. Researchers demonstrated two pneumatic backfilling technologies recently developed under the USBM's Abandoned Mine Reclamation Research Program, the Pneumatic Pipefeeder and the High-Efficiency Ejector. Both systems had previously been evaluated at the USBM's subsidence abatement investigation laboratory near Fairchance, P A. The objective of the demonstration was to fill 100% of the abandoned tunnel with backfill stone to prevent further subsidence. The Pneumatic Pipefeeder was used for 21 days, at a rate of 63 to 124 t/ d (69 to 136 st/d), to fill 88% of the tunnel. The High-Efficiency Ejector was used for 2 days, at a rate of 125 to 132 t/d (138 to 146 st/d) to fill the remaining 12% of the tunnel. The backfill placed by both systems was tightly compacted. The major problem encountered was wear on the polyethylene pipeline from the abrasion of the high-velocity backfill. The use of heavier steel pipe minimized the problem. A cost analysis for the entire project is given.

Jan 1, 2010

By G. M. Zhao

The gasification of lump coke with CO2 was studied in a fixed-bed reactor. The effective diffusivity of the gas was evaluated from measurements of the reactivity of the lump coke, produced by BHP Steel in New South Wales, and from kinetic parameters that were determined from the reactivity of fine grains. The grain model of effective diffusion in porous media was adopted to express the gasification rate of the lump coke and was found to fit the experimental data well. The relationship between reactivity and textural characteristics of the coke was examined

Jun 18, 1905

By T. A. Henrie, J. D. Marchant, E. S. Shedd

Cerium metal was electrowon in a fluoride bath from cerous oxide and tapped from the cell during prolonged operation . Electrolyte constituents were CeF , BaF₂ , and LiF. Twenty- seven pounds of metal of 99.8 percent purity were produced at a rate of 3 pounds per hour and tapped from the cell . Principal impurities were molybdenum , aluminum , oxygen , and carbon . The operating parameters , such as electrode geometry , bath compositions , and oxide feed rate , were investigated . Anode reactions were found to be important factors in cell operation . Stable cerous oxide reacted more uniformly at the anode surface than ceric oxide . Electrowinning was conducted in crucible hearths consisting of both frozen electrolyte and molybdenum metal . Both materials proved satisfactory and did not react with the molten cerium . Stable cerous oxide was prepared by carbothermic reduction and used as a feed material . Cell design proved to be an important factor in continuous cell operation . Complementary to the investigations of electrowinning of cerium , the metal was purified by electrorefining in a chloride electrolyte .

Jan 1, 1964

By N. H. Darton

In mining coal in the anthracite region of Pennsylvania the general custom has been to leave a large percentage of the coal in place as pillars to support the roof. Evidently any practice that involves partial waste of an important mineral resource is bound to be discarded. It is well recognized that one method of obviating probable waste is to fill the workings with cheap or worthless materials, a process extensively employed in the anthracite and some European mines. At present many of the collieries in the anthracite region of Pennsylvania are utilizing refuse from the old culm banks, which formerly were prominent features in the landscape, and are flushing the fine waste underground so that pillars may be reduced in size or removed. As a result the banks are now disappearing and soon will be gone. The fine culm from the breakers and rock from the mines will continue to be available, but the volume of these materials is insufficient to replace any considerable proportion of the coal removed. The next stage of progress suggested is the use of sand. Fortunately there are available large deposits of this material, much of which can be handled by dredges and pumps. This report is issued by the Bureau of Mines in the interest of safer and more efficient mining methods. I ts purpose is to describe the sand deposits in the northern anthracite coal field in Luzerne and Lackawanna Counties, Pa, Much of the information available is presented in the map, Plate I. Field studies, mostly preliminary, were made in the summer of 1911 to determine the distribution, amount, and character of the larger deposits. It was not thought desirable to make a detailed examination of the region because when the coal companies decide to utilize the sand their engineers will make precise surveys and drill test holes. In preparing the map the various coal companies were consulted; they contributed a large number of facts, especially as to the deposits in the buried valley of the Susquehanna between Pittston and Nan- ticoke, where nearly 1,000 test holes have been bored. The results of these borings were placed at the author's disposal, and have been utilized in drawing the boundaries given in the wide valley area and its extensions up Lackawanna River and NewportCreek. Wyoming Valley contains deposits of sand that are 100 feet thick over a wide area, 200 feet thick in places, and over 300 feet thick in the deep old channel south of Plymouth.

Jan 1, 1913

By J. A. L. Campbell

The Galatia Mine is a dual-seam underground coal mine located in Saline County, IL. In 1984, it became the first coal mine to be permitted by the Illinois Department of Mines and Minerals to operate diesel equipment underground. And it is one of the larger underground coal mines in the nation to use diesel equipment. From the beginning, Kerr-McGee determined that diesel equipment offered the best approach to the safe and productive development and operation of the Galatia Mine. The flexibility of this equipment and its ability to promptly respond to changing conditions and mining locations made its use desirable for building this large dual-seam coal mine. The mine had a planned nominal annual capacity of 3.6 Mt/a (4 million stpy) and would employ more than 500 people. Galatia's current reserves are estimated at 231 Mt (255 million st) of recoverable coal from two seams of high-quality, high-volatile bituminous coal. The Harrisburg No. 5 seam is shipped primarily as a low-sulfur steam coal or as a metallurgical blend stock. It is also used in the pulverized coal injection (PCI) process for steel making. The Herrin No. 6 seam is a medium-sulfur coal. Annual production is shown in Fig. 1. A good indicator of a mine's success is employee productivity improvement. For many reasons - the proper use of diesel equipment, the introduction of longwalls and increased employee ex¬perience - Galatia employees have achieved a steady growth in annual productivity (Fig. 1) while maintaining an exceptional safety record.

Jan 1, 1993

By Don C. Warrington

This paper is a survey of the various methods and research efforts by which the drivability of piles is determined. First, a brief outline of the basic theory and the important parameters for driving by vibration are presented. Then, a wide variety of methods by which the drivability of piles is determined are presented and discussed, with special emphasis on methods developed in the USSR. Each of these methods are examined as to how they take into account the various parameters of vibratory pile driving, such as eccentric moment, frequency, dynamic force, motor torque and power, vibrating and static weight, and other variables. Some relation of these methods of field data is presented as well.

Jan 1, 1989

By Juan Carlos Salas

In this paper, a collaborative R&D model which has been successfully applied by a global mining companies association is presented and analysed both from the conceptual and practical point of view and an example of these collaborative initiatives, the Copper Technology Roadmap recently generated by a group of the most relevant copper mining companies, is presented, including an analysis of strategic opportunities and challenges in the Latin American region.

Sep 9, 2007

By H. Gercek, M. Genis

In this paper, the effects of dynamic loads on the geometry of the failure zone occurring around underground openings, excavated in deep and massive rock masses, have been investigated. Following an elasto-plastic stress analysis of a two-dimensional underground opening under static conditions, dynamic loads have been applied. In the static and dynamic analyses, FLAC2D computer program has been utilized. Maximum ground acceleration value is selected as an input parameter. An index determining the relative size of the yield zone around the opening has been used for comparison of instabilities. In diesem Bericht wurden die Auswirkungen von dynamischen Lasten, auf die Geometrie der Bruchzone in der Umgebung von Untertagehohlräumen, die in tiefen und massiven Gebirge aufgefahren wurden, untersucht. Nach einer elasto-plastischen Spannungsanalyse eines zwei-dimensionalen Untertagehohlraumes unter statischen Beanspruchungen, wurden dynamische Lasten aufgebracht. Für die statischen und dynamischen Analysen wurde das FLAC2D Computer Programm verwendet. Die maximale Bodenbeschleunigung wurde als Eingabe Parameter gewählt. Zum Vergleichen der Unstabilitäten wurde ein Index verwendet, der die relative Grösse der Bruchzone in der Umgebung des Hohlraumes bestimmt. Dans ce papier, l’influence des chargements dynamique sur la géométrie de la zone en rupture observée autour des cavités profondes excavées dans des massifs rocheux ont été étudiées. Des chargements dynamiques ont été appliqués, dans le cas d’une modélisation bi-dimensionnelle de l’excavation d’une cavité profonde, sur la base d’une analyse élastoplastiques des contraintes en conditions statiques. Le code de calcul FLAC2D a été utilisé pour les analyses statiques et dynamiques. La valeur maximale de l’accélération du sol est choisie comme paramètre d’entrée. Un indice déterminant la taille relative de la zone sollicitée autour de la cavité a été utilisé pour comparer les différentes instabilités.

Jan 1, 2003