Search Documents

By Paul J. Remington

The field data gathered as part of the measurements described in Volumes I and II were re-analyzed in the low frequency regime (.1 Hz to 1 Hz) where motion sickness normally occurs. These data were compared co the international standard ?ISO 2631 Addendum 2: Evaluation of exposure to whole body z-axis vertical vibration in the frequency range 0.1 to 1.0 Hz." For both underground mining machines and surface mining machines the results showed that one would not expect motion sickness to .be a severe problem. New field data were gathered on the vibration reduction performance of various seat designs found on surface coal mining machines. The vibration during normal operation was measured on the seat using the standard seat pad accelerometer package described in the previous two volumes and simultaneously on the floor of the machine at the base of the seat. Preliminary indications are that the so-called high performance seats used for operator vibration reduction do not offer significant improvement over conventional seats.

Jan 1, 1984

By W. L. Cooley

The report provides a detailed analysis of 23 electrical accident countermeasures contemplated for use in the metal/non-metal mining industry. The costs and potential benefits of implementing groups of these countermeasures are estimated, and methods arc outlined by which the operator ran choose countermeasures in an effective manner. The analysis is based largely on an extensive electrical accident event tree which is developed in detail. For those countermeasures which are not currently technically feasible, several prototype devices were developed to help speed development. These included a trolley arc eliminator and a safer mine electricians multimeter.

Jan 1, 1982

By R. V. Ramani

This volume is the first of a four-volume final report on research carried out under a contract from the U.S. Bureau of Mines on the development of a computer simulation model for surface mine reclamation planning. The other volumes are titled as follows: Volume II: Dragline Model, Volume III: Mine Coordinate Generator System, and Volume IV: User's Manual for OPMHS/2. This report deals with the development of a geological model for surface mine planning. The most common orebody modeling techniques are described. A brief review of geostatistical theory and concepts is presented. A geostatistical option for orebody modeling is developed and validated. Computer programs and sample outputs are appended.

Jan 1, 1985

By Terry R. Neumann

A mineral survey of the 23,760-acre Abert Rim Wilderness Study Area (OR-1-101) was conducted by the U.S. Bureau of Mines in 1986 at the request of the Bureau of land Management in order to evaluate its identified mineral resources. The study area is located in south-central Oregon, 26 mi north-northeast of Lakeview, OR. Federal and Lake County mining records indicate no mining claims, geothermal leases, or oil and gas leases within the study area as of January 1, 1987. No economic concentrations of minerals were found in the study area. The Wilderness Study Area is dominated by Abert Rim, a north-trending Basin and Range fault scarp that parallels the study area's western boundary. Exposed on the scarp is an approximately 2,000-ft-thick volcanic sequence consisting of Oligocene-Miocene basalts, tuffs, and tuffaceous sedimentary rocks.

Jan 1, 1987

By G. ALBORNOZ, S. Utili, A. AGOSTI, C. VALDERRAMA, R. PELL, N. Morales

The steepness of the slopes of an open pit mine has a substantial influence on the financial return of the mine. The paper proposes a novel design methodology where overall steeper pitwalls are employed without compromising the safety of the mine. In current design practice, pitwall profiles are often planar in cross-section within each rock layer; i.e., the profile inclination across each layer tends to be constant. Here instead, a new geotechnical software, OptimalSlope, is employed to determine optimal pitwall profiles of depth varying inclination. OptimalSlope seeks the solution of a mathematical optimization problem where the overall steepness of the pitwall, from crest to toe, is maximized for an assigned lithology, geotechnical properties, and factor of safety (FoS). Bench geometries (bench height, face inclination, minimum berm width) are imposed in the optimization as constraints which bind the maximum local inclination of the sought optimal profile together with any other constraints such as geological discontinuities that may influence slope failure. The obtained optimal profiles are always steeper than their planar counterparts (i.e., the planar profiles exhibiting the same FoS) up to 8° depending on rock type and severity of constraints on local inclinations. The design of a copper mine is first carried out employing planar pitwalls, secondly adopting the optimal pitwall profiles determined by OptimalSlope. The adoption of optimal slope profiles leads to a 34% higher net present value and reductions of carbon footprint and energy consumption of 0.17 Mt CO2 eq and 82.5 million MJ respectively due to a 15% reduction of rockwaste volume.

Feb 9, 2022

By M. A. Elliott, H. H. Schrenk, L. B. Berger, John C. Holtz

"INTRODUCTION Diesel-powered locomotives designed specifically for underground operation were used in the construction of some of the tunnels that comprise the Delaware Aqueduct in New York State. Before this there had been limited use of Diesel-powered equipment such as trucks, bulldozers, and shovels in tunnel construction in various parts of the country, but this equipment was used without modification for underground use and, in some instances, appar¬ently without due consideration of the hazards that might be created by the introduction of fuel-burning equipment into confined underground spaces.As certain definite advantages were apparent if Diesel haulage could be used in tunnel construction in some sections of the Aqueduct, the contractors who were to construct the tunnels in these sections were desirous of using, this type of haulage equipment if it could be used with safety. This matter was given careful consideration by the various agencies concerned with the establishment of safe practices on the Aqueduct project before tunnel driving was started. Of chief concern were the quantities of toxic or objectionable materials that would be discharged into the tunnel air by the exhaust of the locomotives and the volume of ventilating air that would be required to dilute these exhaust gas products to concentrations permissible in the atmosphere of working places."

Jan 1, 1947

By E. A. Metz

Ergonomics is the art and science that tries to understand the complex interrelationships among employees, their work environment, equipment, work methods and job demands. Coal and metal/nonmetal miners are exposed to a higher number of ergonomic risk factors than in non-mining occupations. In addition, studies have shown that these miners experience more degenerative disc disease and osteoarthritis than comparable industrial populations. A general discussion of the risk factors that cause overexertion injuries and disorders will be presented. In addition, the basic principles of ergonomics will be discussed with specific cases to show how successful programs have been developed. A successful ergonomics program should simultaneously improve health and enhance productivity.

Jan 1, 2002

By Michael G. Zabetakis

The spillage of liquid diethyl ether in rooms at floor level and 3 feet above the floor resulted in flammable vapor-air mixtures in the immediate vicinity of the exposed liquido The liquid temperature was found to decrease by as much as 35° C., with a resultant decrease in vaporization rate. A search of the literature yielded numerous references to unstable peroxide (residue) formed by the autoxidation of ether. Such residues appear to constitute an explosion hazard in the condensed state.

Jan 1, 1962

By George T. Faust

The petrographer engaged in examining the products resulting from the beneficiation of ores, and rock minerals is constantly required to develop new means acid methods of assaying microscopically the results of such operations. From time to time investigators have published descriptions of apparatus that have aided in solving problems in processes of physical separation. Thus, in 1919, Coghill and Bonardi 3/ published a paper covering the application of the binocular microscope and camera lucida to the microscopic analysis of pulverized ores. Similar work has been published by Schneiderhohn 4/ Schwartz 5/, and Head and his associates 6/, 7/, 8/. The present paper goes further and considers application of the polarizing comparison-microscope to problems directly concerned with mineral dressing where it is desirable to compare analogous products, and in addition it suggests new uses in various related fields. This work was conducted under the cooperative agreements of the Southern Experiment Station of the Federal Bureau of Mines and the University of Alabama.

Jan 1, 1940

By D. L. Putnam

Snap Lake Mine ?? Complex dyke ore body ?? Underground operation ?? 1.1 million tonnes per annum ?? 1.2 carats per tonne ?? On-site diesel power generation ?? Supply by ice road and air ?? Milestones ? Construction commenced in 2005 ? Commissioning 2007 ? First diamonds August 2007

May 1, 2008

By Harpal Parmar

This paper evaluates dynamic methods of pile capacity prediction by comparing their results to static load test results. Dynamic and static pile load test data were assembled from four southeastern states of the U.S. End-of-drive and restrike capacities were evaluated using the Pile Driving Analyzer (PDA) and by wave equation (WEAP) analyses. These were compared to static (Davisson criterion) loads. The best comparison was obtained for restrike PDA results; restrike wave equation analyses values also compared well. The end-of-drive results for both methods-showed relatively poor comparisons. The PDA was recognized as an important tool to measure energy transferred to the pile; this transferred energy was recognized as an uncertainty when conducting wave equation analyses. A statistical analysis showed restrike capacity results to be associated with higher precision and accuracy as compared to end-of-drive methods. The authors believe that restrike dynamic testing is essential to establish long term static soil strength and that it will lead to accurate and cost-effective design of piles.

Jan 1, 1996

By Milne J. Schmid

A program has been conducted to determine the feasibility of providing a borehole liner for Kelly Bar drilled boreholes in Southern Florida. The concept was to drill the borehole with the Kelly Bar and with it still in the borehole insert a tube which would remain in the unstable ground after withdrawl of the bar. The tube then will provide an unobstructed borehole for the charging of explosives upon completion of the drilling the shot pattern.

Jan 1, 1977

By John Kosek

The electrochemistry of carbon monoxide, nitric oxide and nitrogen dioxide was investigated at a variety of electrode materials in different supporting electrolytes. A portable detector for carbon monoxide was developed using a porous gold anode in perchloric acid supporting electrolyte. This detector has two full scale ranges, 0-100 ppm and 0-500 ppm. A portable detector for mixtures of nitric oxide and nitrogen dioxide was developed using a porous silver cathode in sulfuric acid supporting electrolyte. Nitrogen dioxide was determined in the gas stream by electroreduction. The nitric oxide in the gas stream was oxidized to nitrogen dioxide by passing it over Cr(VI) on firebrick. Electroreduction gave the sum of NO + N02. Analog circuitry was used to display the amounts of NO and N02 separately. Two ranges were available for each gas. They were 0-10 and 0-50 ppm for NO and 0-2 and 0-10 ppm for N02.

Jan 1, 1979

By G. K. Derby

The Bureau of Mines investigated methods for removing dragline bucket wire rope terminations with the objective of finding efficient methods that are safer than the method most commonly used at U.S. surface mines, which is to use the explosive impact of a projectile fired from a cannon to remove the rope termination. Removal of a wire rope termination for repair or replacement requires separation of the wedge and socket that lock together to secure the rope end. The Bureau investigated currently used methods and improved upon and tested two safer alternate methods for removing wire rope terminations. A cannon test program was conducted, using 40-and 50-gr primer (detonating) cord, to establish the possible force produced with a 4-in-bore cannon and a 55-lb projectile. Wedge and socket units supplied from cooperating mines were separated under controlled conditions to establish data on separation force requirements. The two alternate methods investigated were use of the force generated by (1) a pendulum ram and by (2) a portable hydraulic pusher. Both methods are capable of providing sufficient force to effect wedge and socket separations on draglines with up to 78-yd3 buckets under normal conditions.

Jan 1, 1984

By David Burgess

Natural gas is a general term applied to the gas obtained from oil or gas wells. It is the most widely used of all gaseous fuels. The principal disadvantage in the use of this and other gaseous fuels is the difficulty encountered in the storage and transportation of large quantities in the gas state. Handling in the liquid state is possible, but reduced temperatures are required since methane (table 1) is the principal component of most natural gases that are used as fuels. Actually, liquid storage has been utilized both here and abroad;3 however, the Cleveland disaster4 has pointed out the need for a critical evaluation of the hazards involved in the storage of this cryogenic fuel. Accordingly, a program was undertaken to obtain basic data that could be used to assess these hazards. In this report, the factors to be considered in an evaluation of the fire and explosion hazards associated with any fuel are each discussed briefly. These factors are then used to assist in the design of experiments for the evaluation of the hazards associated with liquefied natural gas (LNG) relative to those associated with other common fuels. Experiments have been conducted on the vaporization of LNG, the mixing of LNG vapors with air, the effect of temperature and nitrogen dilution on the limits of flammability of methane in air, the burning rates of LNG and other fuels, flame radiation, and extinguishment of fires above liquid pools. Based on the results of these experiments, LNG can be stored safely in suitably designed above-ground tanks surrounded by earthen dikes in much the same manner as gasoline.

Jan 1, 1962

By P. Zhang

A multiyear, comprehensive study of flotation reagents used in phosphate beneficiation was conducted. The study involved the evaluation of pure fatty acid compounds, comparison of various anionic collectors and testing of iso-acids. Various C12 to C22 fatty acids were tested as Florida phosphate collectors. The saturated fatty acids were found to be very poor collectors when using the standard conditioning procedure, whereas the unsaturated C16 to C22 fatty acids showed fair to good phosphate collecting ability. The C18 fatty acids oleic, impure oleic and linoleic and the C20 eicosenoic acid were shown to be the best phosphate collectors. The best flotation results were obtained using Liqro GA tall oil and oleic acid. Four isostearic/iso oleic acid type fatty acid collectors were compared with a commercial grade oleic acid and with Liqro GA tall oil as phosphate collectors using standard laboratory conditioning and flotation procedures. The most selective collector evaluated was Century 1108, a high isostearic acid-type reagent. However, it was concluded that this excellent-performing reagent was too expensive for commercial use. Overall, the most promising reagent was probably Century MO-5. This collector is essentially an iso-oleic acid/stearic acid mixture (not isostearic acid), and it costs much less. This program laid a sound foundation for developing single collector, all anionic flotation processes.

Jan 1, 2009

By J. M. Kuchta

The Bureau of Mines investigated four simulated coal gob fires to obtain a more reliable data base for defining the state of a sealed mine fire and to evaluate the performance of various fire detectors. The fires were conducted in a multiple-entry section of the Bruceton Experimental Mine by heating 4,000 to 21,000 pounds of rubblized bituminous coal to ignition and monitoring the temperature, gas emissions, and smoke under ventilated and sealed combustion conditions. Product gas concentrations depended upon the coal bed size, coal temperature, heating rate, and oxygen concentration or ventilating condition but varied little after the fires were sealed. Expressions are given that define the temporal variation of CO and O2 after sealing when the coal temperature decreased rapidly. The CO/C02 ratio is a more sensitive fire indicator than the CO/?02 ratio, although the latter is universally used for detecting the incipient state of a coal fire. In comparison, the Jones-Trlckett ratio [ CO2 + ¾ CO ? ¼ H2 ?O2] is less reliable for this purpose. The best detector for determining the state of a mine fire after it has been sealed was a prototype submicrometer smoke particulate sensor. Limitations of the various detector systems are also discussed.

Jan 1, 1982

By M. Z. Emad, M. U. Khan, A. ur Rehman

Stemming plugs are used as an accessory in drilling and blasting industry. They supplement conventional stemming material (i.e. drill cutting) with retention of gases in the drill hole that result in better fragmentation of rock and improved explosive utilization. Better fragmentation and explosive utilization along with economic benefits enhance efficacy of the project. Incorporation of stemming plugs in drilling and blasting industry is in exercise for about thirty years. The efficiency of stemming plugs is a key factor in their rising induction in mining industry. Different studies have been conducted on the economic viability of these plugs. The focus of this paper is the selection of stemming plugs for a bench blasting operation and the examination of blasting operation efficiency based on ergonomics and human factors. Three types of stemming plugs were evaluated during multiple blasts at a limestone quarry. Their performance was evaluated using split desktop software. Based on the human factors plastic molded stemming plug (stemming plug-1) was found to be the best among all selected plugs. INTRODUCTION Surface mines and quarrying operations heavily depend on bench blasting to achieve high volumetric targets and production demands. Use of explosives is the most economic method adopted for rock breakage and movement. Extensive research had been performed to enhance explosives energy utilization. This include changing the drilling pattern, application of air decks, stemming plugs, and use of other supportive devices. Optimization of explosive energy has been a major concern in those mines that rely on drilling and blasting operation to carry out main production. Due to continually increasing cost, efficient mining demands, and associated hazards of using explosives, it is necessary to utilize explosives at their best. Efficiency of a blasting operation is generally evaluated by the fragmentation size. From post blast conditions at blasting site to efficiency of processing plant, anything can be affected due to improper blast resulting in bad fragmentation. Better fragmentation is necessity for better operation of the system along with consideration of the safety of operation, environmental issues and related costs. For developing a blast design, an engineer should always attempt to minimize the cost of operation without compromising with acceptable technical and safety necessities [1]. Blast performance is dependent on many different factors associated with the process. These factors have been gauged as blast geometry, explosive specification, and rock mass properties [2]. Similarly, in 2013 Mohammad et al. concluded that fragmentation dynamics depends on blast hole diameter, primer, spacing, stemming, burden, and delay timing for blasting operation [1]. At the work site where this study was performed, blast holes were filled by drill cuttings and muds to help in confining gases. In a blast hole, gas confinement helps in better rock fragmentation along with reduced flyrocks. This practice is most common in many countries including Pakistan. Due to lack of homogenized particle size, the effectiveness of confinement is variable and majorly based on the size of stemming. Extremely small sized drill cuttings often result in hole blow out along with flyrocks from the collar. This improper blast energy will result in poor blast, bad impacts on environment, and reduced operational efficiency. In addition to the stemming material, the length of stemming is also a prime consideration. The decrease in stemming length will increase the quantity of explosive in the blast hole and an increase in stemming material generally improves stemming performance.

Jan 1, 2019

By Pietro Navarra

Cooling of critical furnace equipment to produce freeze lining is of particular interest as many metallurgical processes are intensified while attempting to prolong campaign life. This idea was combined with high-capacity heat pipes in the design of a copper slag launder. The design methodology of the launder and heat pipe cooling system is examined in this paper. With reliable material properties and operating conditions, CFD was used to quantitatively predict the skull thickness and the corresponding heat load applied to the slag launder. The operational limitations of heat pipe technology were considered and an appropriate cooling system was incorporated into the model. Parametric modeling was used to simulate several launder and heat pipe configurations. The generated results were then used to optimize the design of the launder, which was built and tested in August of 2005. The experimental performance of the cooling system is evaluated and compared with the model results.

Jan 1, 2006

By George Wilson

When pumping abrasive slurry mixtures, special attention must be given to pump design and construction. The second article in this two-part series describes some design features to consider when selecting centrifugal slurry pumps. Hydraulic Design Most centrifugal pumps are conventionally designed to achieve the desired hydraulic performance at the highest efficiency and lowest cost when handling clear fluids in reasonably clean environments. Manufacturing limitations are not imposed on the configuration of the pump, since conventional materials such as cast iron, bronze, and stainless steel are used. Manufacturers and buyers usually select the highest specific speed commensurate with the lowest cost attainable. Part life is almost infinite. When a centrifugal pump is designed for slurry service, the important factors in pump design are wear and materials of construction; size and efficiency assume lesser importance. The pump must operate at low rotational speed and the impeller has to be a truly radial flow design. These factors immediately determine that the pump must be of a low specific speed design in the range of 600 to 1800. The specific speed is a type number that is constant for all geometrically similar pumps; it designates the geometry of the impeller and casing. [ ] where n = rpm, Q = flow (US gpm), H = total head (ft), and Ns = specific speed. Since wear is a function of velocity it can be shown that for a given head and capacity, wear will increase with increased Ns. Centrifugal Pump Casing The casing has a profound effect on performance. If designed incorrectly it can destroy a large part of the energy given to the flow by the impeller, resulting in low efficiency, high hydraulic forces, and excessive wear on both the casing and impeller. In a conventional spiral volute, the static pressure around the impeller is uniform only when there is a free vortex velocity distribution in the volute, i.e., when the spiral flow from the impeller coincides with that of the volute spiral. This occurs only at the best efficiency point (BEP), between the pump's best operating zone and over capacity zone. Departure from the free vortex velocity distribution in the volute at partial or over capacities produces circumferential pressure gradients at the impeller periphery, which is directly proportional to the specific gravity of the mixture being pumped. At partial or over capacities, the flow will not tolerate the abrupt deflection at the tongue and severe energy losses and wear are created near the casing throat and on the impeller. Concentric and semi-concentric volute designs produce uniform static pressures at the impeller periphery and make the pump, much less sensitive to "off"' BEP operation. Hydraulic forces and wear are considerably reduced-eliminating the tongue prevents abrupt deflection of the flow, turbulence is minimized, and the velocity in the casing volute and throat is reduced. Good efficiency is sustained over a wider operating hand. Casings of this design are easy to cast. • Spiral volute (conventional)-Radius to the outer periphery of the casing and the volute area constantly increases. • Semi-concentric casing-Radius to the outer periphery of the casing and volute area remain constant within a certain angle. • Concentric casing-Radius to the outer periphery of the casing and volute area remain constant through 360°. The degree of concentricity must be reconciled with efficiency, hydraulic radial load, and wear for each specific speed chosen. Up to 1200 Ns the casings can be fully concentric without sacrificing too much efficiency. Above 1200 Ns, the casings can be semi-concentric. The angle of concentricity

Jan 10, 1981