Search Documents

By Herbert H. Einstein

Swelling ground is one of the most feared problem in tunneling. Although usually not causing sudden failures during construction, the very large and long- lasting deformations give contractors and designers the impression of facing an inevitable phenomenon against which there is no technical defense. Examples are concrete liners of up to 1 m that have been cracked or crushed, tunnel inverts that are heaving at a rate of 0.1 m per week during construction and continue to heave during decades. This author (Einstein (1979). Einstein et al. (1972) (1975)) and others (Huller (19761, Grob (1972) (1976). Golta (1967), tienke (19761, Krause (1976). Lee et al. (1976)) have described many cases of swelling tunnels that illustrate the significance and magnitude of the problem. This paper intends to show that tunnels in swelling rock can be built to perform satisfactorily. . For this purpose the tunnel builder needs to know how to determine the existence and specific behavior of swelling ground, how to select appropriate structural characteristics of the tunnel and predict its performance under the specific ground conditions, and finally how to construct the tunnel such that the anticipated performance will be achieved. This concept of a design-construction procedure is the same as that for tunneling in general; it is mentioned here for NO reasons: 1. To point out that design and construction cannot and should not be separated. The way in which the tunnel will be built has to be an integral part of the design. 2. This paper will be structured corresponding to the procedural concept.

Jan 1, 1981

By Cem Colakoglu

In this study, nickel containing iron alloys were produced by carbothermal reduction of lateritic nickel ores obtained from Manisa - Caldag region of Turkiye in order to investigate the reaction mechanism of nickel and cobalt. In the experiments, the lateritic ore containing 1.58 wt.% Ni and 0.12 wt.% Co was calcined in a semi-pilot scale rotary furnace at 1100°C for 1 hour. Then, a mixture of calcined ore and metallurgical coke was reacted in sintered alumina crucibles using a graphite resistance tube furnace at different time (0- 60 min) and temperature (1500-1600°C).

Jan 1, 2009

By Russell R. Trengove

Core samples from an ore horizon 2,000 feet below the surface were successfully obtained by rotary drilling at the property of the Eureka Corp., Eureka, Nev. The ore was soft and friable; cores were not obtained previously with diamond drills. Whipstocking was used to get samples in a zone 200 feet from a vertical hole. A technique in shipstocking, by which the direction and deviation of the holes were controlled by means of nonfriction-type survey instruments, was successfully employed.

Jan 1, 1956

By J. R. Cobble

The Federal Bureau of Mines conducted static tests at 2,500° F on 39 refractory compositions, and dynamic tests at [2,825°35° F] on 31 commercial refractory brick specimens to determine their resistance to corrosion and erosion by a slag similar in composition to that used in producing insulating mineral wool. The static tests showed fireclay, low-alumina compositions (<70 percent A1203), zircon, zirconia, SiC, and clay-bonded graphite refractories to be unsuitable. Dynamic test results indicated that magnesia and chromia compositions were superior to high-alumina compositions (=70 percent A1203) as a furnace lining for melting mineral wool. Data from these tests indicated that magnesia and chromia compositions with low RO/R203 mole ratios were more resis tant to attack by mineral wool slags than ones with high RO/R203 mole ratios.

Jan 1, 1975

By Dana T. Updyke

An evaluation was made of one of several improved underground communication systems sponsored by the U.S. Bureau of Mines. The system evaluated was installed in a typical metal/non-metal room and pillar mine and utilized UHF repeaters connected to a unique distributed antenna and passive reflector system which provided mine-wide communications. A microprocessor controlled data collection system was assembled and installed for the evaluation. Data consisting principally or times and durations of messages and identities of the originating transceivers was collected between February and August of 1982 (6 mos.). Analysis of the data shows that the principal benefits are reduction in time required for unscheduled maintenance and repair, enhancement of safety, and better coordination of production activities. A cost benefit analysis shows a net benefit over cost, although it is also concluded that the capacity of the system is greater than can be justified by current activity in the mine.

Jan 1, 1983

By A Liu, T Ren

Gas explosion in underground coal workings can pose a serious threat to the safety of mine workers and the entire mine operations. Gas explosion is a very complex thermal-chain reaction in a confined underground environment. Based on combustion and explosion theory, three dimensional (3D) computational models were developed to simulate mine gas explosion flame and overpressure wave propagation in a single entry gateroad in underground coalmines. Six different explosion scenarios were modelled and compared with large scale experimental results and AutoReaGas simulations. Model validations show that the use of shear-stress transport (SST) k-? model together with eddy-dissipation model (EDM) produces good agreement with both experimental and AutoReagas simulation results. Modelling results demonstrated that the changes of temperature versus time can be divided into four stages, ie&#160;the initial condition stage, and periods of warm-up, active burning, and burnt-out. Assuming a limited volume of methane is involved in the explosion, the maximum temperature decreases as the distance increases from the explosion point, with the highest temperature reaching about 2460 K. Modelling results show that the evolution of the explosion flame shape experiences four typical stages, ie&#160;spherical flame, finger-shape flame, flame with the skirt touching the side walls (ribs) and tulip flame, which are similar to the pattern of a duct explosion. The pressure in the gateroad remains the same as the initial value before the arrival of the explosion wave and then increases rapidly to the maximum value. Modelling results from this study will be used for the design of explosion arresting devices and mine seals in underground coalmines.CITATION:Liu, A and Ren, T, 2017. Computational simulation of gas explosion and its propagation in single entry gateroad, in Proceedings Australian Mine Vent Conference 2017, pp 181–188 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

The National Mining Hall of Fame will induct five mining greats on Saturday, Sept. 17, 2005 at the Museum Convention Center in Leadville, CO. The 18thAnnual National Mining Museum and Hall of Fame Induction Banquet will begin with an open house and reception at 5:30 p.m., followed by the dinner and program at 7 p.m. The five inductees are Nathaniel Peter Hill, John Munro Longyear, John McDonald, Julius Eckhardt Raht and John Dennis Ryan. Nathaniel Peter Hill (1832-1900) built the first successful smelting operation in the Rocky Mountains in1867 at Black Hawk, CO. From 1879 to 1885, he was a U.S. senator. He also taught courses at the Colorado School of Mines.

Jan 1, 2005

By A. K. Tripathy, P. K. Pattnayak, H. S. Ray

The effects of water addition on the solid-state reaction between Cr2O3 and Na2CO3 at low temperatures (up to 873 K) were investigated to determine its possible influence on the reaction rate and the degree of conversion to soluble chromate. Experiments at high temperatures were conducted for comparison. It was found that adding water to the mixture before roasting enhanced both reaction rate and yield significantly. The reactions followed the Lesokhin-Tempelman equation at low temperature and the Ginstling-Brounshtein equation at above 973 K; the respective activation energies were 95 and 22 kJ/mol

Jun 19, 1905

By H. E. Thomas

[The Bureau of Mines has conducted a field hydraulic fracturing experiment to determine the preferential orientation of induced fractures in oil shale at a depth of about 400 feet in the Green River Basin of Wyoming. The hydraulic fracturing treatment was performed by injecting extremely viscous water-base gel and 8- to 12-mesh sand into the oil shale through straddle packers set in an impermeable section of smooth-walled, 6-1/4-inch-diameter open hole. An impression packer proved that a horizontal fracture, which has an average width of about 1/2 inch at the borehole, was induced. A corehole drilled 100 feet from the fractured well intersected the fracture and confirmed its horizontal orientation. Because a horizontal fracture was successfully initi¬ated, it is inferred that the creation of multiple, closely spaced horizontal fractures may be feasible in Green River Basin oil shale.]

Jan 1, 1972

By J. C. Irvine

Meramec Mining Company, a joint venture by Bethlehem Steel Corporation and St. Joe Minerals Corporation, is engaged in the mining, concentrating, and pelletizing of iron ore from the Pea Ridge Mine located near Sullivan, Missouri, about 70 miles southwest of St. Louis. The orebody was delineated in the mid-1950&apos;s by St. Joe during an exploration program to discover new lead orebodies. An airborne magnetometer survey which was run by the U. S. Geological Survey, the Missouri Geological Survey, and several min¬ing companies was published in 1950 and showed an anomaly in the Pea Ridge area. Test holes drilled in 1953 and 1954 revealed the presence of a large orebody of probable commercial significance; additional drilling in 1956 and 1957 provided confirmation of this. Meramec Mining Company was incorporated in 1957 and shaft sinking began in the latter part of that year. The Pea Ridge orebody lies under about 1300 feet of sediments. It is tabular, about 2600 feet long and up to 600 feet thick, and lies in an approximate east-west delineation. The orebody dips about 800S and is of unknown depth. The ore is primarily high grade magnetite with smaller zones of specular hematite, The Pre-cambrian wall rock is rhyolite porphyry. The mine is serviced through two concrete-lined shafts, 19 feet 1 inch in diameter and 2500 feet deep. No. 1 shaft, equipped with an "A" type head-

Jan 1, 1972

By M. F. van der Merwe

Anglogold Ashanti?s Kopanang Gold Plant (previously No. 9 Gold Plant) treats ore from Kopanang and Tau Lekoa shafts. The plant is twin streamed and has dedicated treatment circuits, from milling to final product, for each shaft. Waste rock material is used to compensate for the mill gap on both streams. Each stream consists of three 4.85 m x9.15 m ROM mills in closed circuit with a single stage hydrocyclone, milling an average of 7 000 t per day. The liner configuration in each mill consists of six rows of 30 grid liners along with rectangular lifter bars. The topic of gold lock-up is not new and has been investigated and reported on many times, both within Anglogold Ashanti and the broader mining industry. Although the lock-up mechanism is understood, its measurement is neither practical nor precise. The initial lock-up in a new liner and the release as the liner wears down cannot be accurately quantified. Previous test work carried out on Kopanang Gold Plant (with a ?gold scanner?) measured the natural gamma radiation emitted by uranium. This radiation is in proportion to the mass of concentrate locked up in the grid liner pockets, as well as between the cast-on backing plate and the shell. The ratio of concentrate lock-up was estimated as 35% behind the liners and65% in the pockets. Mill gravity concentrates are recovered during routine relining operations from behind the grid liners at Kopanang Gold Plant. Prior to relining, the liners tend to release the concentrate from the pockets as the liners wear. Historical Kopanang data from actual ?mill gold? smelted indicates that an average of 29 kg gold is recovered from behind each row. This indicates a total lock-up of 250kg gold per mill. This locked-up gold should preferably be minimizedor eliminated for the following reasons: ?The cyclic build-up and release of gold in mills complicates accounting ?Gold concentrate arising from liners is a security risk and creates a major mechanism for gold theft ?Loss of interest on the value of 250 kg fine gold is significant and was a major driver for the project. These factors led to the need to develop techniques to eliminate or at least minimize the gold lock-up in the mills. Wave liners, with rubber inserts, have been successful in eliminating lock-up, and were tested at Kopanang Gold Plant in November 2000. However, due to increased load-slip and high wear rates associated with these liners, this option proved less economical in terms of liner wear. Grid liners, with rubber-filled pockets, demonstrated a very high wear life and eliminated pocket lock-up. This system was successfully trialed in January 2003, but unfortunately did not prevent lock-up behind the liners. Current developments have resulted in a system that eliminates both pocket and backing plate lock-up. The conventional grid liner design has been modified to remove its steel backing plate. Rubber inserts that are integrated onto a rubber backing plate, have been designed to be used with the newly modified grid. The backing plate and grid pockets are now completely occupied by rubber, thus completely eliminating concentrate build-up around the new grid liner system installed in November 2003. Results to date are promising and liner life is expected to exceed conventional performance.

Jan 1, 2005

By Robert Harris, David Duncan

The Samira Hill gold mine represents the first commercial gold project for the landlocked country of Niger in West Africa. It began production in October 2004 as the result of over 10 years of exploration and development work. There were several administrative, social and technical challenges that had to be overcome to realize the successful development of the project. The Samira mine is located on the geological structure known as the ‘Samira Horizon’ which is developing as a promising district for additional discoveries and other mine developments.

Jan 1, 2005

By S. G. Beattie, N. Mojtabai

A study was carried out which aimed to: determine the effects of blasting on excavation perimeters and nearby slopes; establish a low-cost blast monitoring and field observation programme to determine peak particle velocities and blast damage; and to develop criteria for observable blast damage that are based on the peak particle velocity. Full-scale production blasts in a large open pit copper mine were monitored and studied to develop damage criteria for various rock types. Better blast designs can be achieved by correlating the results of blast monitoring with field observations of damage at the pit walls and on benches. Back-break and damage are related to blast-induced ground vibration. Peak particle velocity is accepted as a reliable measure for the prediction of ground vibration levels. Empirical models for the estimation of rock damage can be developed and used for blast design. The models are used to determine the zones of damage within the rock face. Rock damage models can also be used to design trim shots to achieve further reduction of back-break in more critical areas

Apr 1, 1996

By L. D. Johnson

On a project which is to develop a system to suppress coal dust explosions, a facility has been built and several devices tested. The facility is a 317-foot, 4.5-foot diameter shock tube and to date 53 tests have been carried out with methane-air and methane/coal dust-air as the explosive mixtures. Suppression of slowly propagating (up to 300 ft/sec) flame fronts has been successfully carried out on two tests using the dry chemical extinguishing agent Purple K. Delivery of the material directly into the flame front Seems to be required if effective suppression is to be accomplished.

Jan 1, 1972

By J. Douglas Causey

In 1984, at the request of the Bureau of Land Management, the Bureau of Mines studied 9,600 acres of the 12,350-acre Antelope Creek Wilderness Study Area (MT-065-266) in order to evaluate its mineral resources. Within this report, these 9,600 acres are referred to as the study area. The Antelope Creek Wilderness Study Area, Phillips County, MT, adjoins the north end of the Charles M. Russell Wildlife Refuge. Considered part of the Missouri River Breaks, the area straddles the edge of a thrust fault zone that has deformed the Mesozoic strata in the west half of the area. Shale, siltstone, and sandstone of Cretaceous Age are exposed in the area. Coal beds averaging 3.0 ft thick occur in the Judith River Formation. About 0.20 million short tons of coal were mined from the Judith River Formation adjacent to the west boundary of the area; no production is known in the study area.

Jan 1, 1986

By J. Bertisen, G. Davis

Previous analyses of small samples of mining projects have found that feasibility studies tend to well under-estimate the actual capital costs of the project. Our review of 63 mining and smelting projects completed over 4 decades confirms that as-built capital costs are, on average, 25% higher than as estimated at the bankable feasibility study stage. There appears to be little attenuation over time of this bias in capital cost estimation, at first appearing to reflect an absence of learning on the part of the consulting engineer. We instead argue that this persistence of bias is intentional, driven by a scarcity of project financing and the need to inflate the project economics in a bid to secure financing. Around this intentional bias is a considerable amount of scatter. Roughly half of all projects’ as-built capita costs fall outside of the expected ±15% of the feasibility study capital cost estimate, even after allowing for intentional estimation bias. Cost overruns of 100% or more happen in roughly 1 out of 13 projects. The data reveal that a shifted lognormal probability distribution should be used when modeling mining project capital costs in a Monte Carlo analysis.

Jan 1, 2007

By A. C. Richardson

[During the past two and a half sears the U. S. Bureau of Mines and the University of Alabama, with the cooperation of the different coal operators, have been making an extensive studs of coal preparation in the State of Alabama. Considerable time has been devoted to the studs of the washing characteristics of the Mars Lee bed and the various methods used In preparing from it a low-ash coal suitable for the manufacture of metallurgical coke. One of the phases of this problem is the utilization of middlings products from the washing plants. This paper gives the results of treating jig middlings on a coal-washing table at the Bureau of Mines laboratory at Tuscaloosa, Ala. The sample used was secured from the Sayreton washery of the Republic Steel Corporation, Sayreton, Ala. WASHERY PRACTICE The Mary Lee bed is very bony, and operators find it difficult to produce from this bed a washed coal much under 10 per cent ash. Experience has shown that in the preparation of a coking coal from the Mary Lee bed it is best to use a process which permits the recovery of a middlings product. Middlings are desirable because separation according to specific gravity is never perfect, and a middlings product makes possible a low ash in the primary warned coal without excessive losses of combustible in the refuse. The general washery practice on the Mary Lee bed is to crush the run-of-mine coal through some maximum screen size and wash it upon some one type of jig without re-treatment of any of the products made. The maximum size treated varies from 3 inch to J inch. The middlings product from multiple-cell jigs is usually termed "boiler fuel" and when possible is utilized as such. At present the production of boiler fuel is often in excess of power requirements, and the surplus, due to its high ash content, becomes waste.]

Jan 1, 1931

This paper discusses support requirements for the proposed monorail system to be used in decline development. The monorail drilling and loading systems are systems that move on the rail (monorail) installed in the roof of the decline and supported by roof bolts, suspension chains and steel supports. However, due to the weight of the components of the two systems, it is imperative that the force in each roof bolt, suspension chain and steel support capable of suspending the weight of the heaviest component is determined. Numerical models that relate the weight of the monorail drilling and loading components to the required strength in the support system have been developed. Using these developed models, numerical values of the forces in each roof bolt, suspension chain and steel support, required to suspend the weight of the heaviest component of the monorail drilling and loading systems are determined.

Dec 6, 2010

By Jay A. Berger

Nondestructive testing of deep foundations for integrity problems made great strides in the late 1980&apos;s. Inexpensive portable computers have allowed the immediate and rapid processing of field measured acceleration records which can provide insight into the relative structural integrity of a previously installed foundation member. Although the gathering, processing and displaying of the data is now straightforward, interpretation remains at times rather challenging. This paper provides a brief introduction into the theoretical basis for data interpretation and the hardware necessary for data acquisition. Five case studies are discussed which demonstrate the varied applications of low strain integrity testing of deep foundations and the efficiency at which they are completed. BACKGROUND One dimensional wave mechanics, when applied to a linear elastic pile with a length that is an order of magnitude greater than its width, provides a straightforward basis for the interpretation of motion measurements made at a pile top. When impacted, a stress wave travels through the pile at a wave speed, c, which is a function of the elastic modulus, E, and mass density p (i.e., E=pc2). The applied load F, and particle velocity v, at a point are related by the equation F=Zv. For a cross-sectional area A, the proportionality constant Z is equal to EA/c. Because Z is a measure of the pile&apos;s resistance to change in velocity it is called the pile impedance.

Jan 1, 1990

By Syd S. Peng

Introduction The most commonly used ground control design in coal mining is the determination of pillar size by various pillar strength formulae for mine layout (Bieniawski, 1983; Holland, 1973; Hustrulid, 1976; Obert and Duvall 1967; Wilson and Ashwin, 1972). However, there have been few documented case histories concerning the validity of those strength formulae. Recently there are indications that those strength formulae tend to overdesign considerably. From a safety point of view, there is nothing wrong with overdesign. But an overdesign with large chain pillars reduces the flexibility of machine movement and decreases production. It also reduces coal recovery and, thus, shortens the reserve&apos;s life. This is especially true for small operators who own a limited reserve. Those small mines, through past practices or out of necessity, experiment with smaller pillars than those predicted by the strength formulae. Conclusive ev¬idence has been collected that points to the need of a new concept of coal pillar design. Two case studies will be cited to illustrate this point. 3-D US pillar strength formulae Figure 1 shows a sectional layout of a one-unit mine. The seam was about 1.3 m (50 in.) thick with a uniform cover of 64 m (210 ft). A house was located near the center of the section. The homeowner demanded that no surface subsidence and domestic well dewatering should ever be allowed as a result of underground room-and-pillar mining. Physical properties - strength and Young&apos;s modulus - of the rock strata including coal were obtained by testing small samples in the laboratory. The uniaxial compressive strength of the coal was 3660 kPa (823 psi). Using various pillar strength formulae, the homeowner recommended that square chain pillars be at least 11 m (35 ft) wide. The coal company, however, desired to pursue optimum coal recovery in the safest and most economical manner. They engaged in three-dimensional finite element analysis of the section taking into account the complete stratigraphic sequence of the overburden. Results indicated that the section can be developed by 5.5 m (18 ft) wide entries at 21 m (70 ft) center-to-center. In retreat, the pillars can be splitted along both centerlines leaving a stump pillar of 5.5 m (18 ft) square at each of the four corners. The 5.5 m (18 ft) square stump pillars still maintained a safety factor of 1.5, although the safety factors calculated by various pillar strength

Jan 11, 1986