Search Documents

By C. Feng, C. Elbaum

Knoop hardness measurements were carried out on large grains of iodide titanium containing different amounts of oxygen. For each oxygen content the hardness is recorded ainingas a function of the crystal orientation and of the angle 4 between the indenter diagonal and the projection of the C (hexad) axis in the surface. The results can be expressed by the following relation; hardness = n-k cos 2ø, where n and k are constants for a given oxygen content and crystal surface orientation. A NISOTROPY of hardness is a well-known phe-nomenon and has been reported for many metals.1-3 At the present time, however, such information is not available in the literature for titanium. Consequently, a systematic study of the simultaneous effects of oxygen content and crystallographic orientation on the hardness of titanium was undertaken in this laboratory. Evaluations of oxygen content in titanium are frequently carried out through hardness tests. Although such procedures may be justified in small grain specimens, the results of the present investigation indicate that the anisotropy of hardness should be taken into account in the case of coarsegrained specimens as well as in the case of pronounced preferred orientation. Materials and Experimental Procedures Iodide titanium, 99.99 pet pure and containing of the order of 0.002 wt pet O, was used throughout this investigation. The metal was arc melted in an argon atmosphere and cold rolled into strips 1/16 in. thick. These strips were subsequently recrystal-lized and strain annealed in vacuum (10" mm Hg or better) at 850°C in order to produce crystals varying in diameter from 10 to 25 mm. Oxygen was introduced into selected large crystals by heating at 700°C in an atmosphere of pure oxygen under an observed pressure of approximately 50 mm Hg. Each sample was subsequently annealed in vacuum at 850°C for 100 hr, in order to homogenize the oxygen content throughout the specimen. It was found that longer annealing was not necessary, for no change of surface hardness in a given direction was detected after prolonged annealing. The oxygen content was determined by the difference in weight of the specimens before and after the oxidation-annealing cycle. The accuracy of oxygen determination is within ±0.1 mg in samples weighing 0.5 to 1 g. A vacuum fusion analysis of oxygen was performed on several samples and gave results in good agreement with the ones obtained by the weight change. It should be emphasized that expected weight losses through evaporation of the metal in vacuum at 850°C' are many orders of magnitude lower than the precision of these measurements. Following the annealing treatment, both oxidized and unoxidized crystals were carefully polished. All detectable traces of surface cold working were removed by repeated polishing and etching. Laue back reflection X-ray patterns were taken for each crystal for the purpose of determining the orientation and ascertaining the absence of substructures detectable by this method. Hardness measurements, using a 1 kg load, were subsequently carried out on a Tukon hardness tester equipped with a Knoop indenter. The Knoop indenter was used throughout this work because indentations obtained by means of a Vickers indenter are considerably distorted due to the anisotropy of the elastic constants in titanium. Such distortions are much less pronounced in the case of Knoop indentations, although for some orientations a cer-

Jan 1, 1959

Study on Mineral Processing of Refractory Copper-Nickel Ore

Sep 13, 2010

By Leslie H. Sharp, Martin J. Gavin

"Introduction.Investigations of the oil shales of the State of Colorado were begun February 1, 1920, by the U. S. Bureau of Mines and the State of Colorado, under cooperative agreement entered into by the Bureau and the State, funds for which were provided by the State. The investigations are for the purpose of determining by large-scale Laboratory retorting tests, those conditions which will produce optimum yield of best quality products from Colorado shales. (For an outline of the work and description of the apparatus, see Gavin, Martin J., and Sharp, Leslie H., ""investigations of the Fundamentals of Oil-shale Retorting,"" Reports of Investigations, Bureau of Mines, July, 1920.)In the preliminary work which is usually required when a new material is being dealt with, certain physical and chemical constants of the shales being investigated, and their products, were determined; these data will be of much value not only to the thorough retorting tests now under way at Boulder, but to engineers who will design and construct oil-shale plants. While the figures presented in this report apply only to the shale used in the determinations, strictly speaking, the shale used was selected to represent, as well as possible, an average of the massive type of oil shale encountered in Colorado. The figures, therefore, can probably be applied with little danger of serious error to any massive Colorado oil shale which yields in the neighborhood of a barrel (42 gallons) of oil to the ton.This paper is based on a more complete article now being prepared in which experimental methods are explained in full, and complete experimental data. For the purpose of presenting the data with as delay as possible, it has been decided to anticipate the more complete article with the present report."

Aug 1, 1920

By P. Roy

Smelting or converting of sulphide concentrates and mattes in a batch operation presents a challenge when directing the off- gas to a conventional acid plant. The Hindustan Zinc Ltd. (a division of the Vedanta Group of companies) Chanderia Lead Zinc smelter was presented with such a challenge that was met with the adoption of the Cansolv® SO2 Scrubbing System. The Ausmelt top submerged lance technology used at Hindustan Zinc generates a furnace gas stream that containsbetween 0.1 vol% and 12 vol% SO2 during the three stages of batch smelting. Cansolv® SO2 Scrubbing Technology captures the SO2 to ensure that treated flue gas exits the facility at a concentration below 100 ppmv SO2 and it releases SO2 in a controlled fashion, to more closely match the needs of the existing acid plant. The application of a regenerable scrubbing system to capture SO2 from a batch-operated furnace and convert it to acid in a conventional acid plant was a first of its kind in the world. This paper provides an update on the design and operation of the Hindustan Zinc SO2 recovery system and suggests two improvements to the basic flow sheet that optimize the cost of SO2 scrubbing further.

Jan 1, 2007

By J. Bleeck, G. Mahrt

INTRODUCTION Many excellent papers have been written and presented regarding agricultural lime and the subject has been covered extensively in books concerning soil science, fertilizing, limestone, etc. We felt challenged to construct a paper that wouldn’t merely be a repetition of past presentations. Therefore, we chose to begin with factors having the most impact on plant growth realizing that the audience is likely to be relatively unfamiliar with this subject. So, we decided to dig deep into the roots of soil and plant growth science in order to better understand the significant role of limestone in this important area. The soil with the higher plants growing upon it forms an open and dynamic ecosystem in which there is flux of energy and material (heat, light, water, nutrients, mineral and organic matter, organisms). Plants root in the soil and then take up oxygen for root respiration, yielding energy for nutrient uptake, water for turgescence and transpiration and use in photosynthesis and the mineral nutrients needed for the synthesis of organic matter. Above the ground the plant takes in light energy and heat using them in photosynthesis to assimilate atmospheric CO2. Photosynthesis is the basic life process of creation. However, we will look at the root room where soil, water, air, and heat economy and the supply of nutrients determine soil fertility and the important role lime plays here. Location is the primary point to be considered when discussing agriculture (climate and soil); secondly, the dynamic and mobility of the minerals (plant nutrients) in the soil; and thirdly the conversion of organic substances into humus. And then there is a great deal of water involved in the growing process. In order to produce 1 kg of dry plant substance, 300 to 800 kg of water must be pumped through the plant and is then lost by transpiration. Cereals, vegetables, and sugar beets consume between 400 to 500 kg of water during the growing process and long-growing crops, such as alfalfa and clover, can consume 600 to 800 kg of water per kg of finished product. Without water, a plant cannot grow. (Reference 1)

Jan 1, 2006

By J A. Singer, S R. Iverson, C A. Link

High resolution seismic refraction tomography has proved to be a useful tool to effectively estimate depth of blast induced damage in a mine face. Excavation blast damage can be as shallow as 1 to 2m and requires resolution at a fraction of a meter for effective imaging. We used an accelerometer with flat frequency response to 1000Hz to record data at spacings of approximately 0.25 to 0.5m along mine walls. First arrival times from the seismic data were used to produce P-wave velocity tomograms. The tomograms show transition from low velocity zones to velocity associated with competent rock. We interpret the low velocity zones to indicate residual fracturing from blasting. Experiments on a concrete test block and at two underground mine locations give results that are consistent with fractured rock transitioning to competent rock. Our method can be applied efficiently in an underground environment to provide continuous velocity information with depth into a mine wall over a span of approximately 10m.

Jan 1, 2009

Fast Adsorption Phenomena at Air/Liquid Interfaces

Sep 13, 2010

1.0 Control House (DWG. NO. 56-401-G) - 1.1 Physical Description The Control House is a single story, 2728 square foot building with an adjacent transformer yard. A four foot overhang provides shade protection for the walls. The building is heated and air conditioned. The HVAC System has an elevated outside air intake and provides a positive pressure environment within the structure in order to prevent the infiltration of heavier-than-air, noxious gases. The materials of construction are as follows: Structure : Light-Gage Metal Framing Exterior Walls :Outside - Preformed, Metal Siding :Inside - Insulated Metal Liner Panels Interior Partitions :Gypsum Board over Light-Gage Metal Framing Roof :Insulated, Preformed Metal Panels Ceilings :Mechanical & Electrical Rooms - Exposed underside of Roof Panels Control Room, Lunch Room, Toilets, Entry - Suspended Acoustical Lay-In Tile Floors :Mechanical & Electrical Rooms - Concrete Slab on Grade Control Room, Lunch Room, Toilets, Entry - Resilient Tile Exterior Doorsand Windows :Preformed Metal Panel Manufacturer's Standard Units

Jan 1, 1979

The following report summarizes the results of engineering feasibility studies whose purpose was to assess the probable efficiency, reliability, safety and cost of a number of possible methods for removal of radon gas from the ambient air in underground mines. Fourteen candidate techniques were evaluated. Seven of these were based on specific individual principles, and seven were based on combinations of these principles. The individual principles were as follows: 1. Activated charcoal 2. Organic fluids 3. Semipermeable membranes 4. Molecular sieves 4. Cryogenics 6. Chemical reaction 7. Centrifuge The combinations were: 8. Cryogenics and activated charcoal 9. Cryogenics and molecular sieves 10. Cryogenics and chemical reactions 11. Membrane filters and organic fluids 12. Membrane filters, cryogenics and activated charcoal 13. Membrane filters and chemical reactions 14. Silica and an Organic Fluid

Jan 1, 1975

By Thomas Novak, Robert Goldstein

The analysis of a machine-luminaire configuration is a time- consuming process requiring the construction of a machine mockup, installation of a designated lighting arrangement, and an extensive set of illumination measurements. This entire process, however, is well suited to computer analysis. By simulating the machine geometry and the characteristics of the desired luminaires, the incident light levels can be calculated at the required set of points. This Bureau of Mines paper presents a general description of the techniques involved in performing this simulation.

By Thomas A. Printz

The wide use of carbon steel in construction and engineering projects makes this engineering material accountable for approximately 85% of the total annual steel production worldwide. Despite the lack of corrosion resistance of carbon steel, it is incorporated into the permanent work for marine applications, power plants, transportation projects, chemical processing, mining, petroleum production and refining, pipelines, mining and construction equipment. Corrosion is an electro-chemical process that occurs in the presence of water and air. When an electric current is introduced to water or soil, the rate of carbon steel corrosion increases rapidly. Gaseous atmospheric constituents that are capable of electrolytic activity can also increase the rate of corrosion. Corrosion tends to be more rapid in environments in which the steel is exposed to water, and then air, rather than being constantly submerged. The exposure to seawater increases steel pitting because the electrical conductivity is improved in salt water.

Jan 1, 2013

By C. S. Samis, D. P. Seraphim

In the presence of oxygen, galena is oxidized in an aqueous medium containing ammonium acetate in accordance with the following reaction: PbS + 1/2 0, + 2 NH~Ac -» PbAc, + So + 2 NH: + H2O. This reaction was studied in an autoclave under oxygen pressure by polarographic measurement of the concentration of lead ion in solution. Oxidation rate is parabolic. The reaction products are lead acetote and elemental sulfur, the latter forming a film on the galena crystal. Reaction kinetics appear to be determined by the diffusion of lead from the galena phase to the solution interface through the film of sulfur. RECENT applications of pressure leaching on a commercial scale have emphasized the metallurgical importance of the oxidation of sulfide minerals in aqueous media by oxygen under pressure. Research experience has shown that sulfates, thio-nates, and metal oxides are the products of humid oxidation of sulfide minerals in basic solutions. The metal oxides may be solubilized in the presence of a complexing ion.' Certain oxide minerals are also amenable to treatment by this type of oxidation.' Several kinetic studies have been made of reactions of this type. Stenhouse' found that pyrite (FeS?) oxidized in a sodium hydroxide solution to produce a soluble sulfate and an insoluble layer of iron oxide and that the kinetics of the reaction were controlled by oxygen diffusion through the oxide layer. Andersen' studied the oxidation of galena (PbS) in a sodium hydroxide solution under oxygen pressure. He found the lead and sulfur to be simultaneously oxidized to produce plum bite ions and sulfate ions, and that the reaction rate was proportional to the surface area of the galena. The kinetics appeared to be determined by the reaction of oxygen and water with the galena surface. In each of the above reactions the metal and sulfur components of the mineral were oxidized simultaneously and at equal rates. In the present study the alkaline medium has been replaced by an approximately neutral solution of ammonium acetate in which lead sulfate is soluble. Under the conditions no sulfate was produced and no sulfur could be detected in the solution. The metal component of the mineral was solubilized and the liberated sulfur remained as a film of elemental sulfur on the surface of the galena crystal. A kinetic study of this reaction was undertaken to establish the kinetic mechanism and to determine the rate controlling step. Specific reaction rates were determined by oxidizing crystals of galena of measured surface areas in an autoclave maintained at the desired temperature and oxygen pressure. The rate of reaction was followed by measuring the concentration of lead in the ammonium acetate solution with a cathode ray polarograph, employing stationary platinum electrodes incorporated in the autoclave. Experimental Materials and Equipment Crystals of galena obtained from Violamac Mines, Retallack, B. C., were selected for oxidation because

Jan 1, 1957

By Aparup Chattopadhyay, Barun K. Gorain

"Porphyry copper deposits are the most important source of copper and also gold within the orogenic belts. These deposits are characterized by low grade copper ore (0.2% to 1% copper) and host precious metals like gold, silver and platinum. A characterization tool has been developed for complex porphyry type copper-gold deposits with an aim to quantify copper and precious metal deportment. This quantification is a challenging task due to low grades and also due to the presence of both visible and invisible precious metal content in different sulphide and non-sulphide phases. Studies were initiated on various complex ore deposits and also on samples representing various processing streams such as flotation and leach products. This paper presents the development of a systematic approach to diagnostic metallurgy using state-of-the-art optical and automated mineralogy, micro-probe, dynamic SIMS and TOF-SIMS analysis for quantification of invisible and visible precious metals content in various species. The relevance of this characterization to metallurgy will also be briefly discussed in this paper.INTRODUCTIONA novel characterization tool has been developed for double refractory gold ores and complex copper-gold ores using state-of-the-art technology for quantitative gold and copper deportment study. The characterization of these ores is a challenging task due to low copper and gold grades in ores, presence of both primary and secondary copper sulphide phases and variable proportion of visible and invisible gold in different sulphides phases (pyrite, chalcopyrite, chalcocite and bornite) and iron oxide phases (magnetite, hematite and goethite). A study was initiated on various ore deposits and also on samples representing various processing streams of pilot plant batches such as flotation concentrates and tailings. This paper attempts to discuss the deportment characterization methodology through presenting results from investigations on four samples from a flotation circuit viz, Feed, Final concentrate, Cleaner Scavenger Tail and Rougher Tail samples. These four samples represent the key streams for a typical copper-gold flotation flow sheet. The key objective of this investigation was to identify and quantify visible and invisible gold along with understanding the morphology and liberation of gold associated with various sulphides, Fe- Oxides and non-sulphide gangue species. In addition, the aim of this study was also to relate this mineralogical and gold deportment information to metallurgical performance."

Jan 1, 2013

By Mark Jolly, Xiaojun Dai

"Foundry engineers in the traditional foundry usually regard the quality of casting component as the most important issue and leave the energy saving or energy efficiency as the subsidiary one. This frequently causes disproportionate energy consumption as a result of the inefficient casting processes used and increases the production costs. This paper presents the novel CRIMSON aluminium casting process and compares its facility and melting process with traditional melt furnaces and aluminium alloy melting process. A real example is investigated to demonstrate quantitatively how the traditional foundry wastes energy and what the improvement of energy efficiency can be achieved using the new CRIMSON method. The results of this investigation will help the foundry engineer recognize the importance of energy saving and demonstrate how to use this new technology to reduce production costs and carbon footprint without decreasing the quality of the cast component.IntroductionAluminium melting in metal casting industry is an energy intensive process where it is estimated that the energy consumption is in the order of 1,700 ~ 4,700 kWh tonne-1 in using crucible and natural gas [1]. Different countries may use different energy resources for aluminium melting: in US the main energy resources are natural gas, electricity and coke [2] and in UK most of the foundry use electricity, gas and oil as energy resources [3]. Due to the pressure of rising energy price and the strict environment law, it is anticipated that under the right socioeconomic conditions, the efficiency optimisation of industrial process can be an important step toward increased industrial sustainability [4]. In metal casting industry the energy efficiency of a casting facility depends largely on the efficiency of its melting and heat treating performance. In association with the two performances, over 60 % of the total process energy costs are represented in a typical casting facility [5] where there are huge opportunities for metal casting industry to adopt the best energy practices for potential energy saving. How to ameliorate the current processes for increasing energy efficiency will have a vital effect on reducing the production costs and increasing the competitiveness. For instance, by implementing some state of the art technologies such as the CRIMSON method in aluminium alloy casting will make use of such opportunities."

Jan 1, 2011

By B Clemen, D Gordon, F Cesnik, P Griffin

In March 2002 Newcrest Mining Ltd commissioned a 4 Mtpa gold-copper concentrator at its Cadia Valley Operations in New South Wales. This paper presents the design and construction considerations, commissioning and ramp up issues related to start up of the concentrator as well as current performance and future expansion plans. Commissioning of the plant was the culmination of six years of project planning, from discovery of the resource during the Cadia Hill drill out campaign in November 1996 to project implementation and plant operation. Current resource estimates stand at around 50 Mt with an average grade of 2.4 g/t gold and 0.8 per cent copper. At current processing rates the project life is expected to exceed ten years. The processing plant comprises a 9.75 m (32 ft) diameter Fully Autogenous (AG) mill, a single 6.7 m (22 ft) diameter ball mill, pebble crushers, gravity gold recovery circuit and flotation plant. Upgrades to the existing infrastructure and manning requirements at Cadia will be discussed as well as the resultant impacts on operating costs for the operation. The processing plant was expected to deliver 290 000 ounces of gold and 30 000 tonnes of copper in concentrate in its first full year of operation and progress against that goal will be presented.

Jan 1, 2003

By A. J. Miscoe, W. M. McKewan, J. R. Bartels

The U.S. Bureau of Mines has established a wire rope research laboratory to examine the factors that affect the life of wire rope. Two 2 in-diameter 6x25 fiber core (FC) ropes were degraded on a bending fatigue machine. These were the second and third ropes in a series of tests on this construction and size rope. Tensile and nondestructive tests were performed on samples of the rope Lo determine the relationship between rope deterioration and rope breaking strength. The tests indicated that once a wire rope nears the end of its service life, both deterioration and the consequent loss of rope strength begin to increase at an accelerated rate.

Jan 1, 1992

By D Craw, L C. Kerr, P Wopereis

Gold placers in the Nokomai and Nevis valleys are dominantly Quaternary in age. They occur mainly in western tributaries of the upper Nevis, eastern tributaries of the middle and upper Nokomai, and in the trunk valleys themselves. Placer gold in both valleys is dominantly a-phase Au-Ag-Hg alloy. Au-Ag alloy is absent or rare in most of the deposits, except in the lower Nokomai. Alpha-Au-Ag-Hg alloy is typically coarse-grained (up to 2 cm), angular, and rarely flattened or folded. Crystalline texture, quartz intergrowths, and psuedo-hexagonal crystal-pluck cavities are common. Fluvial transport distance predicted from the maximum Flatness Index ofAu-Ag-Hg alloy particles is typically less than 10-20 km. Coarse (up to 2 cm) cinnabar is commonly associated with the Au-Ag-Hg alloy, and both were probably derived from hydrothermal sources in western tributaries ofthe upper Nevis and eastern tributaries of the upper Nokomai. Minor secondary Au-Ag-Hg alloy occurs locally in the lower Nokomai, where it coats or cements detrital a-phase Au-Ag-Hg and Au-Ag alloy particles. Au-Ag alloy dominates over Au-Ag-Hg alloy in the lower half of the lower Nokomai alluvial plain and gravel of a raised channel incised into semischist basement adjacent to the plain. The Au-Ag alloy is rounded and commonly flattened and folded. Crystalline texture, quartz intergrowths, and pluck cavities are rare, and a fluvial transport distance of 25-40 km is estimated from maximum Flatness Index ofAu-Ag alloy particles. The Au-Ag alloy, three types of gamet, magnetite, clinozoisite and well foliated schist boulders in the abandoned channel are not found in the pumpellyite-actinolite facies bedrock in the Nokomai. These components were derived from greenschist facies schist and sedimentary sources in Otago, many tens of kilometers north of the Nokomai catchment. They were transported to the Nokomai either in Wakatipu Glacier till or fluvio-glacial outwash that entered the valley via Nokomai Saddle, the confluence with the Mataura, or both.

Jan 1, 2000

By M Logsdon, B Johnson, M Fordham

The underground Neves Corvo copper-tin mine in southern Portugal currently disposes of its tailings in a ætraditionalÆ wet tailings impoundment. With the development of new technologies for preparation and transport of thickened tailings or paste, alternative tailings disposal options have become available that provide a more sustainable water management system and a higher degree of environmental protection. In addition, growing European resistance towards subaqueous disposal may well result in mandatory use of dry disposal methods in the near future. Twenty-four tailings disposal alternatives were evaluated through a cost-effective and easily-implementable bench-scale geochemical screening program conducted at site. Since the tailings are pyrite-rich and highly acid generating, particular emphasis was placed on monitoring likely indicators of sulfide oxidation under the various simulated disposal scenarios. Dependent parameters investigated as part of the program included moisture content, use of alkaline additives (lime, cement), use of a bactericide, and agitation. Response parameters included paste pH, specific conductance, and temperature as indicators of oxidation. The testing was carried out for 30 weeks. Results indicate that a number of relationships between the geochemical stability of the samples (ie sulfide oxidation) and sample characteristics can be readily identified. Based on the results of the screening program, a limited number of tailings mixtures have been selected for further long-term testing in field weathering cells to aid in the identification of the optimal mix design for future tailings disposal at the Neves Corvo Mine. This type of testing provides an inexpensive and reliable methodology for semi-quantitative comparison between tailings disposal alternatives, in particular at locations where more rigorous evaluation through long-term, fully replicated testing is not immediately feasible.

Jan 1, 2003

By George J. Carter

Data obtained from field and laboratory examinations were used by the Bureau of Mines to evaluate 82 silica deposits in the Pacific Northwest. A total of 94 field samples was taken from 64 deposits, and an additional 18 deposits were investigated that did not warrant sampling. Of the 37 deposits found to be of high quality, only 16 were large enough to be classified as industrial silica resources. Another 27 deposits did not meet quality requirements. Methods of simple low-cost beneficiation and rapid classification of a large number of samples were investigated in the laboratory. These tests indicated that high-intensity electromagnetic separation was equal or superior to either high-or low-intensity electrostatic separation. In general, the electromagnetic method gave higher recoveries and produced equal or better grade concentrates. A glass button method developed for estimating iron oxide content of silica samples proved to be highly satisfactory as a means of classifying field samples and evaluating beneficiation tests.

Jan 1, 1962

By H. Meseck

Dynamic pile test methods to establish the bearing capacity of driven piles were developed in the USA more than 20 years ago. In the Federal Republic of Germany, the first dynamic pile tests were carried out at the end of the 70's. Today dynamic pile tests are successfully used to establish the integrity and bearing capacity of driven and bored piles. The Institute of Foundation Engineering and Soil Mechanics at the Technical University of Braunschweig has developed its own method of measuring and evaluation for the execution of dynamic pile tests. The principles of the dynamic pile tests, the measuring and evaluation plant as well as the experience gained with it in the examination of cast-in-place piles are presented in this contribution.

Jan 1, 2010