Search Documents

By M. Valdebenito, J. Rajala

An OCS Expert control system was implemented by Svedala Cisa at the Minera Maricunga Refugio Crush-Leach Operation near Copiapo, Chile. The purpose of the Expert system was to maximize production through the primary and secondary crushing circuits and help balance crusher usage between each stage to maximize total plant production. Interesting aspects of the control strategies are discussed. Benefits of the control were verified through a randomized On/Off test program. Tonnage increases ranged from 5% to approximately 20% at good confidence intervals. Benefits analysis results are discussed. The crushing plant at Refugio is very remote and is located at approximately 15,500 ft. This poses many challenges. The effect of altitude and remote location on plant operation are discussed.

Jan 1, 2002

Process Options for Difficult Arid-Region Nickel Laterites In the absence of the discovery of significant nickel sulfide deposits, the future of Australia's nickel industry will increasingly depend on cost effect processes for low-grade nickel laterites. The problems encountered with the West Australian HPAL plants, resulting in three of the four plants being shut down, have caused the industry to revisit atmospheric leaching options, particularly heap leaching. West Australian laterites are characteristically very varied in grade, chemical composition and mineralogy with the result that, thus far, one process does not fit all laterites. In this paper the leaching of an especially refractory ore is compared using column leaching of whole ore and atmospheric leaching and HPAL processing of ground ore. The key characteristic is the resistance of the goethite phase to acid attack with low-to-moderate temperature leaching conditions. The refractory characteristic is attributed to the stabilising influence of chromium and aluminium and possibly manganese substitution in the goethite crystal structure and goethite morphology. A significant three-fold increase in both nickel and cobalt extractions under atmospheric leaching conditions was achieved by the relatively simple modification of bubbling sulfur dioxide into the reaction vessel to create a reducing environment. Recoveries increased from <30 per cent to 90 per cent nickel and 86 per cent cobalt after 10 hours of leaching at 95¦C. An even greater improvement was achieved under ambient conditions by heating the ore to temperatures above 250¦C for 30 minutes. Subsequent leaching at ambient temperature gave an eight-fold increase in both nickel and cobalt recoveries after 14 days bottle rolling. Both methods could be optimised and implemented in such a way as to increase laterite reserves in conjunction with a heap leach operation but may be better suited to vat or closed tank processing.

Sep 13, 2010

By W P. Player

The legislative operating environment, or the mineral regime, that a country has to offer is one of the key determinants that a company wanting to invest in an area takes into account in formulating its investment decision.   The New Zealand Government recognises this and the importance of getting the regime right in order to provide for continuing investment in mineral exploration and mining in New Zealand . In recent years, the Government has given considerable attention to developing legislation which provides for investment to take place; for those making the investments to have a stable, fair and open investment environment with government intervention only when considered absolutely necessary because other approaches are not working; and for the people of New Zealand to know that investment must meet acceptable health and safety standards and have acceptable impact on the environment. Also of key importance is having a clearly defined mining regime which includes rules on how to obtain a permit and rules in respect of ongoing permit compliance, rights to develop a mineral resource and permit conditions (in particular, the royalty regime). In New Zealand , these matters will all be addressed in what are referred to as 'minerals programmes'.   The Crown Minerals Act 1991, which is the legislation governing the allocation and management of permits for Crown owned minerals, requires that the Minister of Energy prepare minerals programmes. Minerals programmes establish the policies, procedures and provisions that the Minister shall follow in exercising his or her functions and powers under the Crown Minerals Act. Minerals programmes set out the principal reasons for and against adopting these policies, procedures and provisions and also restrictions on prospecting, exploration and mining for Crown owned minerals. Essentially minerals programmes define the mining regime for the minerals to which they apply, other than the taxation regime, environmental and health, safety provisions, land access matters and general matters concerning the investment climate.

Jan 1, 1995

By David Belknap, Clay Haynes, David Egger

Rehabilitation challenges were met nearly two months ahead of contract schedule for the Design-Build, Fast Track Scituate Aqueduct & Tunnel project in Cranston, Rhode Island. The aqueduct and tunnel were built in the 1920s and consisted of three sections—a 2.3 m diameter reinforced concrete section that extends approximately305 m before it transitions to a horseshoe-shaped 2.3 m wide by 2.1 m high cast-in-place concrete tunnel that continues for approximately 5.3 km until it transitions back to a 2.3 m circular section that extends approximately 1.9 km to the end of this project. Major repairs were required to assure sustained operation of this water supply tunnel.

Jan 1, 2005

By J. W. Givens, P. B. Crawford

A potentiometric model study has been made of the effect of vertical fractures existing in the matrix of the reservoir on the flooding or cycling performance. Fractures can have unusual flow characteristics. Fluid entering one side of a fracture can emerge on either the same or opposite side of the fracture, depending on the particular streamline. Fracture orientation has a great influence on the sweep efficiency. However, sustained fluid injection may still permit large areas to be swept. INTRODUCTION One can find considerable information available in the literature on the effect of fractures originating at the wellbore on sweep efficiencies of water-flooding or gas cycling programs.1-5 However, there arc few, if any, quantitative data reported in the literature on the effect of vertical or horizontal fractures existing out in the reservoir matrix on secondary recovery performance. Several papers have been presented on the effect of vertical and horizontal fractures on the productivity or conductivity of waterflood and gas injection patterns, but in all cases the fractures initiated at the well and simulated commercial fractures.6,7 It is believed that natural fractures may exist out in the reservoir matrix and would effect the displacement performance. The purpose of this report was to study the effect of a few isolated vertical fractures existing out in the reservoir matrix on the performance of waterflood or gas injection patterns. DESCRIPTION AND EQUIPMENT Since the potentiometric model was described by Lee8 it has been widely used to study numerous types of fluid displacement problems. The potentio- metric model can be used for fluid displacement studies when the following assumptions are valid: (a) steady-state conditions exist; (b) the mobilicy ratio is one; and (c) the capillary and gravitational effects can be neglected. Five-spot and direct line drive square patterns were studied using a copper strip of the desired length and orientation to simulate a vertical fracture in the reservoir matrix. The 20 x 20-in. model was considered to represent only one element of an infinite array of similar patterns. DISCUSSION AND RESULTS FIVE-SPOT PATTERN — ONE FRACTURE BETWEEN INJECTION AND PRODUCING WELLS Fig. 1 shows a quadrant of a five-spot pattem with the vertical fracture existing out in the matrix along a line connecting the injection and producing wells. Length of the fracture was equal to 35.4 per cent of the distance between injection and producing wells. In this particular pattern it is noted that fluid breaks through from the injection well to the producing well when the dimensionless time is equivalent to 26.9. Dimensionless time is defined as volume of fluid injected divided by the volume of displaceable fluid in the pattem expressed as a per cent. The cross-hatched areas of this

Jan 1, 1967

By John P. Shubilla1, Nicholas Kyriazi

A joint effort by the Pittsburgh Research Center (PRC) and the Mine Safety and Health Administration (MSHA)3was undertaken to determine how well self-contained self-rescuers (SCSR's), deployed in accordance with Federal regulations (30 CFR 75.1714), held up in the underground environment with regard to both physical damage and aging. This report presents findings regarding laboratory-tested SCSR's in the fifth phase of testing from mid-1993to early 1996. The SCSR's were tested on human subjects and on a breathing and metabolic simulator (BMS) at PRC. These results indicate that most of the apparatus, if they pass their inspection criteria, perform satisfactorily.

Jan 4, 1996

By C. E. M. Meskers

End-of-life Electronic and Electrical Equipment, o_cially called WEEE, is unjustly regarded as mainly a waste management problem. What is structurally overlooked is the enormous resource impact of these devices. EEE rep- resents a tremendous metal resource, which should be uti- lized through e_ective recycling, which has a much lower environmental footprint than primary production. The actual amount of end-of-life EEE recycled today is embar- rassingly low since insu_cient EEE is collected and part of the collected EEE is exported to developing countries, where it is largely not entering o_cial recycling systems. To achieve a global recycling society issues like technol- ogy, economics, life cycle structure, stakeholder aware- ness and legislation have to be addressed in a global, co-operative manner so that sustainable closed product cycles can be obtained. Requirements for a "global re- cycling society" are de_ned to address today's reality of global ows of used consumer products, taking into ac- count the likely needs of the future.

Jan 1, 2009

By K-H. Frohne

This report presents a study of the Cooper sand of the Fork Run pool of Warren and McKean Counties, Pa., and a prediction of the secondary oil recovery by gasflooding the reservoir. A computer program employing a modification of the Craig, Geffen, and Morse secondary recovery calculation was used to make the gas flood performance forecast and is presented in the appendix. The Cooper sand reservoir in the Fork Run pool lies at a depth of about 1,900 feet and covers an area 1/2 mile wide by 2-1/4 miles long. Original oil in place is estimated to have been 8,266,000 STB. The primary recovery mechanism is solution gas drive, and ultimate primary recovery may reach 20 percent over a well life of 90 years. Two computer predictions were made for gas flooding the Cooper reservoir. The first was for a 25-acre pilot five-spot utilizing existing wells, but project economics were poor since only 25 percent of injection gas is utilized for pilot oil recovery. Recovery was 71,000 STB, or 22 percent of oil in place at flood initiation, but required 25,700 scf gas injected per STB of oil recovered. In the second prediction, pilot area performance was projected for the entire Fork Run pool, and economics became good. Recovery was 1,753,000 STB from 25 five-spots after the injection of only 6,400 scf per STB of oil recovered.

Jan 1, 1969

By Chuck Edwards

"Cameco operates the high-grade McArthur River uranium mine in northern Saskatchewan, and is constructing the high-grade Cigar Lake uranium mine. Cameco has studied the concept of underground milling of high-grade uranium ore. Compared to conventional milling on surface, the underground milling scheme appears to offer significant cost savings and a lower environmental impact. This paper describes the underground milling scheme, presents process flowsheets and plant layouts, and provides an assessment of potential benefits from underground milling.INTRODUCTIONCameco CorporationCameco is the world’s largest uranium producer, with three operations in Saskatchewan (Rabbit Lake mine/mill, McArthur River mine, and Key Lake mill), two in the United States (Crow Butte and Smith/Highland ISL operations) and two new mines being developed in Canada (Cigar Lake project) and Kazakhstan (Inkai project). Cameco provides uranium fuel refining and conversion services at its Blind River and Port Hope facilities in Ontario. Cameco is part owner (31.6%) of Bruce Power that leases eight nuclear power plants located in southern Ontario. Cameco is the majority shareholder in Centerra Gold Inc., which operates gold mines in the Kyrgyz Republic and in Mongolia.Global Uranium Production RequirementsCentral to Cameco’s view of future uranium supply requirements is the belief that the world is experiencing a nuclear renaissance. This belief is supported by a number of developments, including:•,?Countries representing half the world’s population are now constructing new nuclear power plants. Many countries without nuclear power have begun to plan for it, seeking reliability, clean air and energy independence.•,?Accelerated growth for this industry is also becoming much more likely. In Asia, primarily in China and India, 92 reactors are under construction, on order or planned to help meet rapidly expanding economic needs. Other Asian countries, such as Vietnam and Indonesia, with large populations and rapidly growing economies, are also expected to follow.•,?In the United States the “Energy Policy Act of 2005”, the first energy legislation introduced in over a decade, was signed. This legislation includes provisions recognizing, for the first time at a national level, the clean air contribution of nuclear energy and its critical role in meeting energy security. Upon signing this landmark legislation President Bush stated, “We will start building nuclear power plants by the end of this decade.”"

Jan 1, 2007

By M. Rebolledo, N. Mora, G. Zarate

For decades, the mining industry has been focussed to find an efficient and economically attractive process for the leaching of chalcopyrite. Jetti Resources has developed a novel hydrometallurgical alternative to extract metals of value from mineral ores that the mining industry has struggled to process. Jetti’s catalytic technology, whilst being especially advantaged for extracting copper from low-grade and highly refractory minerals, such as chalcopyrite, seamlessly integrates with existing heap leaching methods and downstream processing operations. The technology uses a catalyst which weakens the metal-sulfide bond in the crystalline structure of the chalcopyrite mineral and alters the structure of the passivation layer allowing the leaching process to continue. Metallurgical test work was conducted to examine the effect of ore variability, in terms of grade and copper deportment. The results presented in this study highlight the amenability of the technology and demonstrate that it is possible to enhance leaching performance of copper primary sulfides over a wide range of copper grades, from 0.1 to 2.2%. Further, it is concluded that despite the copper grade, the tests with increasing chalcopyrite content render copper recoveries up to 4 times higher compared to the tests under non-catalyzed conditions. Jetti’s catalytic technology is currently being evaluated at larger scales, namely a commercial dump leach operation and 50-tonne crib tests. The results obtained thus far are compared to the results from conventional sulfide heap leaching tests. INTRODUCTION For decades, the mining industry has been focussed to find an efficient and economically attractive process for the leaching of chalcopyrite. Chalcopyrite (CuFeS2) is the most abundant and recalcitrant of the copper sulfides (Singer, 2017). Owing to its abundance and economic importance, it is the most demandable natural source for copper worldwide. In fact, the projected demand for copper is further expected to rise much higher beyond the current demand by the year 2020 (Panda et al., 2015). Therefore, it becomes imperative to find low intensity hydrometallurgical technologies for the extraction of copper from chalcopyrite in ores of such low-grades that are un-economic to concentrate and to augment the supply by extracting copper from ores with complex mineralogy that cannot be concentrated (Watling, 2013).

Jan 1, 2019

By A. Boniface

The International Tunnel and Underground Space Association (ITA) has a number of working groups (WG) that meet at least once a year. One of these is WG12, ?Use of Shotcrete?, of which the author is a member. The purpose of this paper is to draw attention to a number of topics that were discussed at the WG12 meetings held in April and September 2008; and also to a number of other matters that arose from the presentation of thirty-four papers at the 5th International Symposium on Sprayed Concrete held in Lillehammer, Norway between 21 and 24 April 2008.

Jan 1, 2008

By Bret N. Lingwall, Byron Foster

The problem of reliable extreme event modeling of large diameter piles under enormous structural or kinematic loads has gained more attention in recent years. In particular, the soil response around the foundation and impacts to buried adjacent infrastructure has gained interest. One of the principal shortcomings with analysis of large diameter pile foundations under extreme event lateral loading is the reliance on conventional beam on elastic foundation methods, which do not model the soil field response around the pile. These methods are limited for large displacement problems, and for large diameter piles. However, the fundamental interactions between steel and concrete, and structure to soil are difficult to constrain, especially in large strain problems where the structural elements become inelastic. The non-linear interaction of the structural materials and soil is desirable so that assessment of stress changes in the field and effects on adjacent facilities can be modeled. A numerical modeling methodology that addresses these shortcomings has been developed. This method utilizes the interaction of brittle concrete with discrete steel reinforcing and casing in a robust manner capturing inelastic non-linearity in both soil and structure. This paper presents a comparison study of the method, wherein three different validation studies were made to data from full scale laterally loaded pile testing. INTRODUCTION Extreme event lateral loading of deep foundations comes in many forms including earthquakes, landsliding, tsunamis, hurricanes, surface fault rupture, liquefaction induced lateral spreads and many more. These extreme events induce loads on foundations far greater than service or strength loads. Perhaps the most dangerous extreme event loads are those of large soil displacements such as landslides, lateral spreads, and surface fault rupture, wherein the soil surrounding the foundations can move laterally 100 mm to 3 m! In these extreme event loading scenarios, small diameter foundations are pushed past their limits and many engineers prefer large diameter deep foundations for these situations. These deep foundations of diameter 900 mm or greater may be auger cast in place piles, cast in drilled hole piles, cast in steel shell piles, cased or uncased drilled shafts, bored precast piles, etc. For convenience in this paper, large diameter deep foundations will be referred to as Large Diameter Shafts (LDS). In LDS, steel may or may not used as a shell around the perimeter of the concrete and/or as internal tensile reinforcement. The interaction between brittle concrete and ductile steel within and/or along the perimeter of the LDS is critical to understanding the non-linear inelastic behavior of LDS for problems of large lateral displacements from extreme events.

Jan 1, 2018

By A. M. Hanna

This paper presents the experimental investigation on the ultimate skin friction of batter piles. The model piles were pushed in medium dense sand deposits at different inclinations up to 30 with respect to the vertical and tested under axial compression loads. The decrease in the total skin resistance with increasing pile inclination can be explained in terms of the reduction of the ave­rage mobilized angle of friction between the pile shaft and sand. The analysis, which takes into account asymmetrical earth pressure distributions around the pile shaft, showed good agreement with experimental results.

Jan 1, 2010

By G. Folmo

Allis Mineral Systems' GRATE-CAR agglomeration/induration/reduction process is currently being operated to process ilmenite at Tinfos Titan & Iron KS in Tyssedal, Norway. In this process, balled ilmenite concentrate is fed to a traveling grate where pellets are dried and preheated, using fully oxidized kiln exhaust gas. Hot preheated, semi-indurated pellets are fed directly to a ported kiln where reduction of the ilmenite's iron oxide fraction occurs in the presence of lump coal. The reduced pellet sand coal char are discharged from the kiln to an indirect rotary drum cooler. Cooled pellets and char are screened and magnetically separated prior to their further processing in a downstream smelting operation. The pellets are melted and the titanium dioxide and iron are separated. Operation commenced in late 1986.

Jan 1, 1992

By H. J. Modi, D. W. Fuerstenau

pH effectively regulates the flotation of corundum through its control of the surface charge. Since collector ions function as counter ions in the double layer, the collector must be anionic when corundum is positively charged and cationic when it is negatively charged. Even a long-chained xanthate will float positively charged corundum. Association of the hydrocarbon chains of the adsorbed collector ions gives rise to increased adsorption and increased rate of flotation. Because of this phenomenon, neutral organic molecules aid flotation although the unionized collector cannot promote flotation independently. Na2SO4 was found to depress the flotation of corundum with animic collectors through ionic competition whereas the same salt activates corundum for flotation with cationic collectors. A close connection between ion association, electrokinetic behavior, and floatability is suggested. As part of the increasing interest in the physical chemistry of flotation, strong experimental evidence has been obtained which indicates that organic ions are adsorbed as counter ions by non-metallic oxide minerals mainly because of the electrical forces which exist at interfaces(1-3). Thus flotation of such minerals without activation should then be appreciable only when the mineral and the collector are oppositely charged. Since only limited work has been reported on the effect of surface charge upon flotation behavior(3) this general hypothesis on the flotation of insoluble oxide minerals has not been tested thoroughly. Investigating the flotation of a mineral for which extensive electrokinetic data exist yields a way to test this hypothesis more extensively. The electrokinetic behavior of corundum in solutions containing both organic and inorganic electrolytes has been studied quite thoroughly' Electro-kinetic measurements have shown that in the case of corundum, simply by controlling pH the solid surface can be charged either positively or negatively. For this reason corundum was chosen for study. The object of this paper is to present a study of the flotation of corundum and to explain the results in the light of our knowledge of adsorption mechanisms gained from streaming potential investigations. This paper is concerned mainly with the effect of surface charge on flotation with anionic and cationic collectors, but in addition such flotation phenomena as collector hydrolysis, Van der Waals attraction between hydrocarbon chains, ionic competition, and activation are discussed. While the present paper is confined to a reporting of the data obtained and some of the more immediate conclusions, it will be seen that the results, in combination with those on other systems, do promise a

Jan 1, 1961

By S. Y. Ezz, K. El•Guindi

A vertical tube, 8 m long and 2.5 cm in diameter, electrically heated to 650°C throughout the majority of its height, was used to study the-effect of ore feed rate and hydrogen flow rate on the reduction of fine iron ore particles. A correlation could be obtained between the combined effect of the amount of reducing gas and reduction time and the per-cent reduction. The results suggest that a method based on the reduction of fine iron ores while falling through up-streaming hydrogen cannot be recommended for industrial application.

Jan 1, 1969

By J. F. Barkley

[There is a general concept in the, coal trade that the moisture- and ash-free B.t.u. of coal from the same seam, and. surely from the same mine, is substantially a constant; that calculation of the -moisture- and ash-free B.t.u. value from the proximate analysis and B.t.u. determined in the laboratory will reveal whether a coal came from a given area or sears; and that, having this constant, the B.t.u. value of a coal sample can be calculated fairly closely upon a dry or as-received basis from the moisture and ash values of its proximate analysis.]

Jan 1, 1941

By Scott A. Stebbins

This Bureau of Mines publication presents a method for estimating capital and operating costs associated with the exploration, mining, and processing of placer deposits. To ensure representative cost estimates, operational parameters for placering equipment and basic principles of placer mining techniques are detailed.

Jan 1, 1987

Due to highly competitive international coal markets, Stockton mine is bound to produce very high quality coals consistently if it is to maintain and expand its market share. The nature of the deposit is such that coals from various source pits are blended in differing proportions to meet the various coal quality specifications of the customer. The complexity arises due to quality variation within the seam both horizontally and vertically and the fact that up to six different products with completely different quality specifications may have to be produced. With increasing demand for this rare product and with CoalCorp eager to meet this demand comes the requirement for computer methods to handle this highly complex problem of both modelling and scheduling.

Jan 1, 1989

By David R. Maneval

The mining of coal in Alaska receives special treatment in the Surface Mining and Reclamation Act passed by the U.S. Congress in 1977 (PL95-87). Section 708 of the Act required that the National Academy of Sciences (NAS) perform a study of "Surface Coal Mining Conditions in the State of Alaska, In Order to Determine Which, If Any, of the Provisions of the Act Should be Modified with respect to Surface Coal Mining Operations in Alaska'. The special committee on Alaskan Coal Mining and Reclamation of NAS completed their study in 1980 and prepared their report (NAS, 1980). At this time, the Secretary of the Interior and the Congress have taken no special action with regard to either special regulations geared specifically to Alaska or to submitting special draft legislation to the Congress requesting amendment of PL95-87. The Alaska Department of Natural Resources (DNR) has drafted legislation which was submitted to and passed by the 1982 session of the State Legislature. The State regulatory agency has also drafted the requisite regulations necessitated by the amendments to the State's Basic Coal Mining Act. It is expected that by mid 1983 DNR will have applied for "primacy" to the office of Surface Mining, U.S. Department of the Interior (OSM). They will be submitting the amended State Law, the revised State Regulations and an operational plan as called for by OSM regulations. The presumption is that primacy will be granted to the State of Alaska under PL95-87. The Usibelli Coal Mine continues to be the only operational commercial mine for coal in the State of Alaska. It produced 7.26 x 10 kg (8 x 10 " T) of coal during 1981. The current mine was started in 1920 by Captain Lathrop, an early developer and pioneer in Alaska. It was continued by Emil Usibelli and was taken over after the death of E. Usibelli (in the 1964 earthquake) by his son Joseph Usibelli who is the current President of, the firm3 Their latest improvement is a 27.5 m (36 yd. )Bucyrus-Erie Dragline which handles most of the overburden removal. The coal is removed by a loader-truck combination. They are currently starting up the use of a unit train loading facility which handles forty cars every two hours. This loading system was a development necessitated by the Sun Eel Export contract. The Alaskan Railroad was a major cooperator in the development of the first unit train loading facility in Alaska.

Jan 1, 1982