Search Documents

By C. A. Snyders

This paper investigates the recovery of platinum group metals (PGMs) from a dilute cyanide leach solution containing base metals, in a manner similar to that used for gold extraction in a typical CIP process, and focuses on both the adsorption and elution stages. The carrier-phase extraction of precious metals using activated carbon offers significant advantages over other processes in terms of simplicity, the high pre-concentration factor, rapid phase separation, and relatively low capital and operating costs. As a sorbent, activated carbon is still by far the most important material because of its large surface area, high adsorption capacity, porous structure, negligible environmental toxicity, low cost, and high purity standards. Adsorption tests were performed on a pregnant alkaline leach solution (0.15 ppm Pt, 0.38 ppm Pd, 0.1 ppm Au) resulting from cyanide extraction performed in column leach tests. The initial adsorption rates of platinum, palladium, and gold were very fast and recoveries of these three metals were approximately 90 per cent after 2 hours and 100 per cent, 97.4 per cent, and 99.9 per cent respectively after 72 hours. The parameters that influence the extraction of PGMs and Au were examined to assess their relative importance during the adsorption process in order to provide the basis for process optimization. The concentration of thiocyanate was not identified as significant factor for PGMs adsorption, while nickel concentration was the most significant extraction process parameter. Base metal cyanide complexes adsorb and compete with the PGM complexes for sites on activated carbon, and while copper adsorption can be minimized by adjusting the residence time, nickel adsorbs at approximately the same rate as that of the PGMs, influencing the loading capacity and adsorption kinetics of the PGMs. The feasibility of eluting platinum and palladium cyanide complexes from activated carbon using an analogue of the AARL process was investigated. Platinum and palladium elute from activated carbon almost to completion in 4 to 5 bed volumes at 80°C, while the elution of gold at this temperature is slow, with a significant amount of gold still to be eluted after 16 bed volumes. Cyanide pre-treatment was found to have a significant influence on PGM elution. Higher cyanide concentration in the pre-treatment step results in more efficient elution up to a point, and experiments suggest the possibility of an optimum cyanide concentration, beyond which elution efficiency starts decreasing.

Jan 1, 2012

By H. R. Babitzke

The purpose of this investigation was to develop an alloy of columbium for use at high temperatures and for nuclear applications. The properties of possible alloys were determined, and the more promising ones were selected for further improvement. Criteria for selection were machinability, hardness, workability, tensile strength, and oxidation resistance. Thirteen 100-gram ingots, ranging from 100 percent columbium to 100 percent vanadium, were prepared and subjected to various tests. Also included for comparison were zirconium and the zirconium alloy, zircaloy-2. Test results showed that a columbium alloy, containing 10 atomic percent vanadium merits further development. Besides being workable at room temperature, the columbium-10 atomic percent vanadium alloy has oxidation resistance superior to the other alloys of the series and is also superior to zirconium or zircaloy-2. The latter two materials have comparable neutron-absorption cross sections. The strength and hardness values of the alloys tested were found to increase with increasing vanadium content, reaching a maximum at 50 atomic percent vanadium and decreasing with further increase in vanadium. This behavior is typical of binary alloys wherein each element will retain any proportion of the other in solid solution. INTRODUCTION There is an increasing need for alloys for service at high temperatures. Since current world reserves of columbium metal approximate 1,500,000 tons (1),4 this metal is now readily available. Columbium can ties; be considered a practical base material for high-temperature alloys required in nuclear reactors and in aircraft and space vehicles. General requirements chosen are: (1) Workability, (2) satisfactory mechanical properties at temperatures approaching 1,000° C., and (3) resistance to oxidation at such temperatures.

Jan 1, 1962

By Kevin M. Connor, O&apos

This report documents-the process of literature review, site selection, instrument installation, data acquisition, and preliminary data reduction performed to evaluate the influence of rock mass discontinuities on coal mine subsidence. A system of surface, subsurface and mine level instrumentation was installed at the Armco No. 7 Mine in Montcoal, West Virginia where the overburden varied in thickness from 630 to 1040 feet. Survey monuments, borehole pressure cells, full profile borehole inclinometer-extensometers, mine level extensometers, stressmeters and tape extensometer convergence stations were installed to monitor displacements and stress changes. Final design of the instrumentation system was based on: a) review of available information, b) field mapping and analysis of areal photography, c) drilling, and d) borehole geophysics. The report contains the complete graphed data of stress and displacements accompanying the longwall mining of a 4800 ft long by 480 ft wide coal panel.

Jan 1, 1983

By Mark P. Zaitsoff

The project involved design, construction, and testing of hydraulic models of culverts, decant and open channel spillways which are typical drainage structures used for protecting mine waste embankments. MSHA (The Mine Safety and Health Administration, U. S. Department of Labor) made a motion picture of the tests. Tests results and products in the forms of graphs, tables and films, demonstrate the principles and factors which govern the function and performance of the three types of drainage structures.

Jan 1, 1981

By Gary A. Halvorson

Plots were established on regraded abandoned mine spoil to determine if nearby good quality spoil could be used in place of topsoil for the reclamation of these sites. Gypsum, calcium chloride, and power plant ash were also tested to determine the effectiveness of these materials in reclaiming these sites. Two sites were selected on which very little vegetation was growing on highly sodic spoil material. Gypsum, calcium chloride, and ash were added to the spoil at a rate designed to reduce the (sodium adsorption ratio) SAR in the surface 15 cm to 10 or less. The good quality spoil (replacement soil) was then laid on the swface at rates of 0, 5 or 15 cm of material. The plots were seeded to a mixture of smooth bromegrass (Bromus enennis Leyss.), crested wheatgrass (Agropyron desertorum (Fisch. Ex Link) Schult.) and alfalfa (Medicago sativa L.). The addition of 5 or 15 cm of replacement spoil significantly improved vegetative growth on these sites. Chemical treatments had no effect on vegetative growth. Weathered ash showed no adverse effects on plant growth or soil properties.

Jan 1, 1991

By P. J. van der Walt

The paper1(hereinafter BG) by two respected sampling experts contains sound theory and logic that can?t be directly refuted. Nevertheless, a practitioner knows that there is a broader context in which the practice of sampling takes place. This broader context, being less well defined than the theory of correct sampling, receives correspondingly less exposure which this commentary??prompted by? BG?seeks to rectify. ?Correctness? of a sampler is the central concern of BG, where it is presented as a sharp ?black-and-white ?distinction. Accordingly, comments below are grouped under the following headings: ?Correctness in practice ?Without correctness, what can be done? ?The broader context.

Jan 1, 2002

By H. S. Sichel, W. J. Kleingeld, C. E. Dohm

A model of ore value distributions is presented that is the culmination of a statistical approach rather than simply a model that has been successfully applied to the evaluation of ore reserves. Detailed geological and physical observations based on large sampling data sets have been used to support the statistical modelling. Fundamental to the modelling process is the concept that the occurrence of a given grade value in space is a function not only of the presence of the mineral but also of the fact that it is associated with a specific trapping mechanism. The concepts have been specifically applied to gold mineralisation

Aug 1, 1995

By Jim Lauder, Russ Calow, Ken Maley, Michael Ounpuu, Stuart T. Caverly

"Stuart T. Caverly, Section Head XRF Laboratory, Jim Lauder, Systems Engineer, Russ Stuart T. Caverly, Section Head XRF Laboratory, Jim Lauder, Systems Engineer, Russ Concession Street, Lakefield, Ontario KOL 2HOAbstractOn-stream X-ray analyzers have become an integral part of modem milling operations. The calibration of these instruments is not difficult but must be performed carefully and with consideration for the principles of X-ray spectrometry. A discussion of successful calibration procedures as well as examples of several common mistakes is presented.IntroductionOn-stream X-ray analyzers (OSA) have become an integral part of modem mineral dressing plants. Advances in instrumentation and computer software make the analysis of process streams fast, accurate and precise. Proper instrument calibration that respects the fundamentals of X-ray spectrometry is essential if the data generated are to be reliable. Often the importance of this task is underestimated and delegated to a person with inadequate XRF training. Successful OSA calibration is the result of careful, systematic procedures.On-stream analysis is perhaps the most important tool that has been provided for the concentrator metallurgist. Combined with powerful, low cost PC's and distributed control systems, real-time elemental analysis affords today's metallurgist many opportunities to troubleshoot and optimize his process.Before OSA, operators had to be very experienced if they were to achieve good results. Even with hourly grab samples, most changes in control approach would still be based on visual cues from the circuit and gut instinct. Real-time analyses have changed that completely.The last two decades have seen a persistent drive to reduce production costs. Operations utilizing OSA have been the most successful in this endeavor. Direct benefits from the application of OSA are fairly obvious. Operators are able to make incremental changes in operational parameters (e.g. reagent addition, pH, cell level), and immediately monitor the effects. Variations in the characteristics of the mill feed can be identified and addressed immediately. More progressive operations have linked analyses to control loops to adjust process setpoints ( e.g. reagent additions), and to change them automatically according to formulas based on previous experience."

Jan 1, 1996

By Y Miyoshi, J Ishibashi

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Sea floor hydrothermal activity in the Okinawa Trough is considered a modern analog to ancient Kuroko-type volcanogenic massive sulfide (VMS) deposits. Recent scientific drilling projects at active hydrothermal fields have enabled us to conduct comparative studies on hydrothermal clay minerals between ancient and modern systems. Zonal distributions of clay minerals below the sea floor of an active hydrothermal field have been revealed, which is represented by the distinctive assemblage of clay minerals. Zone 1 consists mainly of montmorillonite and sometimes of kaolinite; Zone 2 consists of chlorite and chlorite-smectite mixed-layer mineral; and Zone 3 is represented by the co-occurrence of illite and chlorite, from shallow to deep. This zonal distribution is likely to be in accordance with that reported previously for the Kuroko-type ore deposit. Similarities are also recognised in chemical compositions of illite and chlorite, which are both abundant clay minerals in the vicinity of the ore deposit. While illite would be formed by interaction with the hydrothermal ore fluid, the formation of Mg-rich chlorite is attributed to Mg metasomatism caused by the involvement of sea water. Further studies, especially focusing on interactions between fluid and solid phases, would significantly promote our understanding of dynamic processes for the formation of VMS depositsCITATION:Ishibashi, J and Miyoshi, Y, 2015. Hydrothermal alteration process in active sea floor hydrothermal systems in the Okinawa trough, from a viewpoint of a modern analogue for the Kuroko-type volcanogenic massive sulfide deposits , in Proceedings PACRIM 2015 Congress, pp 481–486 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

Abstract A new approach is introduced for study of the behaviour of geotechnical strength parameter prior to slope analysis to ascertain whether strength parameters of slope materials are homogenous or heterogeneous at different mine depths. The strength parameters used for the study are uniaxial compressive strength, tensile strength and shear strength. The analysis is based on statistical analysis of variance technique for one-way classification. The application of the technique is given through a case study in an openpit mine. Auszug Eine neue Annäherung wird für Studie des Verhaltens des geotechnischen Stärke Parameters vor Steigunganalyse eingeführt, um zu ermitteln, ob Stärke Parameter der Steigungmaterialien homogenous oder an den unterschiedlichen Grube Tiefen heterogen sind. Die Stärke Parameter, die für die Studie verwendet werden, sind einachsige zusammenpressende Stärke, Dehnfestigkeit und Scherstärke. Die Analyse basiert auf statistischem varianzanalytische Technik für Einwegklassifikation. Die Anwendung der Technik wird durch eine Fallstudie in einer openpit Grube gegeben. Abstrait Une nouvelle approche est présentée pour l'étude du comportement du paramètre géotechnique de force avant l'analyse de pente pour établir si les paramètres de force des matériaux de pente sont homogenous ou hétérogènes à différentes profondeurs de mine. Les paramètres de force utilisés pour l'étude sont résistance à la pression uniaxiale, résistance à la traction et résistance au cisaillement. L'analyse est basée sur statistique la technique de l'analyse de variance pour la classification à sens unique. L'application de la technique est donnée par une étude de cas dans une mine à ciel ouvert.

Jan 1, 2003

By Peter Rubie, Toni Kojovic, Fengnian Shi

"Mining companies have recognized that characterization of ore breakage plays an essential role in the design and optimization of comminution circuits.Recently the Julius Kruttschnitt Mineral Research Centre (JKMRC) has developed a new breakage model incorporating the effect of particle size, and a new breakage characterization testing device, called the JK Rotary Breakage Tester (JKRBT), which allows rapid testing of particle breakage under high energy single impact and low energy repetitive impact conditions.Positive feedback received from mining company sponsors to the new technology has prompted the JKMRC to further validate the device and the model through a formalized validation program using machines designed and manufactured by Russell Mineral Equipment (RME). The first unit was installed and commissioned at the Anglo Platinum laboratory in Johannesburg in March 2007 and four more major mining companies will participate in the validation program in 2008, including Barrick, BHP Billiton, Rio Tinto and Teck Cominco. The results from validation tests at the JKMRC and Anglo Research have shown that the JKRBT generates statistically similar breakage parameters to the traditional Drop Weight Test, but with significant advantages over its predecessor. Application of the JKRBT in geometallurgical testing with the AMIRA P843 GeM project has confirmed the JKRBT device offers a rapid and consistent method for determining the hardness of drill core samples. The JKRBT has the potential to revolutionize ore testing, with applications in laboratory impact breakage characterization of rock samples, drill cores, coal and other materials. It also stands poised to significantly advance the process control and management of comminution circuits since the concept is readily adaptable to on-line ore hardness measurement.INTRODUCTIONMining companies have long recognized that the performance of a comminution machine such as a crusher or an autogenous / semi-autogenous grinding (AG/SAG) mill depends not only on the machine operating conditions, but also on the “hardness” of the feed material to be broken. This recognition has driven significant interest in laboratory particle breakage characterisation and testing. The laboratory breakage characterization tests can be roughly classified in two broad groups based on their primary breakage modes: tumbling and impact/compression. The famous Bond ball/rod mill tests (Bond, 1952 and 1961) represent the typical tumbling test and have become the industry standard for estimating the specific energy (kWh/t) of rod and ball mills. However, as the energy application in the single particle impact tests can be well defined and controlled, the latter have received significant attention in the last 30 years. It was estimated that mining companies worldwide spent over three million US dollars on single particle impact breakage characterization testing in 2006."

Jan 1, 2009

By Marianne Snedeker

In September 1985 we published a questionnaire asking about the content of MINING ENGINEERING and about your interests. By Dec. 10, our cutoff date, we had 430 responses, representing about 1.5% of the 28,238 people who received the September issue of ME. In the data that follow the tabulation and percentages are based on the number of individuals who responded to the particular question. About ME Through responses to the questionnaire, we were hoping to learn more about you, your interests, and how the magazine could better serve you. Those of you who responded told us something positive - you look at or read the magazine. Of the 430 respondents, 428 or 99.5% indicated that they had read or looked through the July and/or August issues. Those of you who refer to the magazine once are 207 or 48.5%. Those of you who refer to the magazine two or three times are 193 or 45.2%. Those of you who refer to the magazine four or more times are 27 or 6.3%. How much time do you spend reading the magazine? Of those responding to this question: 64 spent up to 1/2 hr 15.0% 224 spent up to 1 hr 52.6% 115 spent up to 1-2 hr 27.0% 23 spent more than 2 hr 5.4% In an informal survey among our staff, we determined that most people spend 1/2 to 1 hr reading magazines to which they subscribe at home. Does that match your experience? Many of you, 335 or 79%, clip your magazine for further reference. Also, many of you, 313 or 73.6%, do not pass your copy on to another reader, indicating that you are clipping it or receiving the magazine at home. Those magazines that are passed on reach: 1 person 3 0.7% 2 people 64 15.1% 3-5 people 34 8.0% 5 or more 11 2.6% Answers to what portions of the magazine you find useful indicated that the top three were Industry Newswatch, feature articles and Technical Papers; see Table 1. The "other" category included advertising - display, classified, Employment, and Professional Services - Washington Survey, New Products, Free Literature, book reviews, technology news, and Coming Events and Short Courses. We asked your appraisal of the technical level of the magazine. Of those responding, 39 or 9.1% indicated that it is too technical, 55 or 12.8% indicated it is not technical enough, and 335 or 78.1% judged it to have the correct technical level. In response to the question about whether you like to read an occasional feature that is not technically oriented, 21 or 5.1% said no, but an overwhelming 94.9% (393) said yes. Of the specific

Jan 1, 1986

By R. E. Mussier

This investigation was made to study new methods to prepare high-purity yttrium metal, Various methods were used to prepare pure intermediate compounds, primarily chlorides, bromides, and iodides, which were subsequently reduced to metal. The process found most suitable for the preparation of pure anhydrous yttrium chloride involved thermal dehydration of a mixture of hydrated yttrium chloride and ammonium chloride while under vacuum. Yttrium bromide and iodide were prepared most effectively by the direct halogenation of yttrim carbide. Yttrim carbide was obtained by reacting and melting yttrium oxide-carbon mixtures in a carbon-arc furnace. Yttrium halides were purified by vacuum distillation and reduced by alkali or alkaline-earth metals. Lithium and sodium proved to be the best reductants from the standpoint of yield (>95 pct) and purity (>99.8 pct) of the yttrium. The product of the reduction step was sponge metal, which was consolidated readily by conventional cold-mold, arc-melting procedure. The purest yttrium obtained in laboratory scale work was prepared by sodium reduction of yttrium chloride and contained only 125 pp oxygen; other impurities did not exceed 1,000 ppm. In larger scale tests yttrium containing only 800 to 1,000 ppm total impurities was obtained by lithium reduction of yttrium chloride. The tensile properties of high-purity yttrium were determined. Mechanical tests showed that yttrium can be forged, extruded, rolled, spot welded, and deep drawn.

Jan 1, 1963

By Paul Headland

The Washington Suburban Sanitary Commission (WSSC) has recently completed design for the Bi-County Water Tunnel Project. The project will include a 10-foot diameter, 5.3-mile long hard rock tunnel located within the Piedmont Physiographic Province in Montgomery County, Maryland. The rock formations present along the alignment are comprised of igneous and metamorphic lithologies. This paper presents the steps taken to characterize the complex geology along the tunnel alignment into a single ?Engineering Unit? based upon the intact rock and rock mass properties. The Rock Mass Rating (RMR) system is planned to be used as the basis for dividing the ground into three ?Excavation and Support? classes. This RMR approach was selected to establish contractual baselines as presented in the Geotechnical Baseline Report (GBR) and is intended to facilitate management of the ground support characterization during construction.

Jan 1, 2008

By D M. Hunter, S M. Iveson, K P. Galvin

For low density materials such as coal, density-based fractionation of particles via the sink-float method is relatively simple due to the availability of liquids of suitable density; however, for high density minerals, suitable heavy liquids are less available and those that are available are expensive and pose significant hazards. At best, sink-float separation can be performed up to densities of 4400 kg/m3 with the use of Clerici’s solution at elevated temperatures. Hence the direct measurement of grade-recovery and density-partition curves is problematic. Therefore, in most cases, beneficiation plants must rely on methods such as QEMSCAN, density tracer particles or very limited information to guide them in the design and optimisation of their plants.This paper describes a density-fractionation method utilising laminar flow through a system of parallel inclined channels to generate a series of overflow fractions at different flow velocities. Here the particles are subject to precise hydrodynamic forces with minimal dispersion or mixing. The size distribution of each overflow fraction at a given flow velocity is obtained using a laser particle size analyser, and combined with a laminar flow model to deduce the corresponding density distribution. The paper describes the application of the method to measure the separation achieved using a REFLUX Classifier to obtain the corresponding feed, product and reject ‘washability curves’, and in turn the full partition surface. Approaches used to corroborate the findings are discussed.CITATION:Hunter, D M, Iveson, S M and Galvin, K P, 2017. A batch elutriation technique for the density-based fractionation of iron ore, in Proceedings Iron Ore 2017, pp 195–104 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By D. D. Runnells

This study focused on the chemical reactions between uranium tailings fluids and cores of subjacent bedrock from the site of the Cotter Corporation uranium mill at Canon City, Colorado. Actual and synthetic tailings fluids were forced through cores of bedrock. The pH of the effluent solutions was the dominant control on the behavior of dissolved species in solution. The pH depended on the presence or absence of calcite cement in the rocks. Calcite neutralized acidic raffinates and caused the precipitation of iron, manganese, aluminum, and possibly uranium. Chloride, sulfate, and sodium were not retarded upon passage through the cores, and sulfate and chloride should be useful as tracers of escaping tailings fluids. Zinc, copper, cobalt, nickel, uranium, and vanadium exhibited high mobility under acidic conditions and were strongly retarded at elevated pH. Calcium was released due to dissolution of calcite and ion-exchange. Magnesium was not retarded in concentrated solutions, but showed moderate retardation in dilute fluids. Potassium and ammonium both showed early retardation followed by breakthrough and mobility. The behavior of molybdenum was strongly dependent on pH, with retardation at low pH and mobility at elevated pH. Selenium was highly mobile under all conditions. Selenium should be a better tracer than molybdenum for many situations. Precipitation of carnotite appears to control the solubility of uranium and, possibly, vanadium. With the exception of the precipitation of aluminum and silica, all reactions were rapid.

Jan 1, 1983

By K. L. Boyd

"Can the increasing tonnages of ore and waste mined today be accommodated simply by using bigger and better crushers? This paper reviews the latest primary crushing and large cone crusher designs. It highlights how—in addition to using the larger crushers now available—maximizing the utilization percentages in each stage of the rock size reduction circuit will assist in meeting the larger production requirements of existing and new mining operations. Its goal is to help consultants and operators select the optimal equipment and custom-designed items in material handling from the mine to the mill, maximizing operating hours per year.RÉSUMÉ Le recours à des concasseurs plus grands et plus performants suffit-il à gérer l’augmentation du tonnage du minerai et des déchets que l’on extrait de nos jours ? Cet article examine les tous derniers modèles de concassage primaire et de grands concasseurs à cône. Il montre que, pour satisfaire aux exigences de production plus conséquente des exploitations minières existantes et nouvelles, il est important d’optimiser les taux d’utilisation à chacune des étapes du circuit de réduction de la taille des roches, en plus d’utiliser les concasseurs plus grands actuellement disponibles. L’objectif de cet article est d’aider les sociétés d’experts-conseils et les exploitants à sélectionner le meilleur équipement ainsi que des articles fabriqués sur mesure pour la manutention de la mine au concentrateur, en optimisant les heures d’exploitation par année.INTRODUCTIONAre larger crushers the answer to meeting the demands of existing or new mining projects for increased tonnage? Boyd (2002) predicted that larger crushers for primary and fine crushing would be beneficial and contribute to the further development of mineral processing. Larger crushers for primary and fine crushing applications have since become available.The rock size reduction process from the mine to the selected milling process facility has not changed since a person first broke a rock to get at the interesting mineralization within. The rock size reduction process circuit from the mine to the mill can be summarized in four stages:• stage 1: mining (rock breakage and fragmentation);• stage 2: prescreening (scalping);• stage 3: primary crushing; and• stage 4: fine crushing (secondary, tertiary, and quaternary).Plant throughput and ore delivery schedule will form the basis for flowsheet design and equipment selection. Once the project design criteria and the mine plan have been established, the circuit’s utilization percentage (percentage of hours when the circuit is being utilized) can be optimized for each of the four stages. The mining and process departments play a key role in the selection of the final comminution circuit, and both departments should be familiar with and contribute to the design of the circuit."

Jan 1, 2017

By Noel N. Moebs

The coal wants at the Westland Mine in southwestern Pennsylvania consist chiefly of elongated, sandstone-filled channels with slickensided basal contacts. Tentatively identified as washouts, these channels are about 1,000 feet long and 300 feet wide, are erratic in occurrence and trend, and are difficult to delineate from the customary core drilling pattern. Roof conditions are hazardous adjacent to the washout contact, but roof stability is generally unaffected greater than 30 feet away.

Jan 1, 1981

By Doug Tesarik

Researchers from the National Institute for Occupational Safety and Health1 (NIOSH), together with employees from The Doe Run Company, are monitoring and evaluating the stability of a pillar retreat section at the Fletcher Mine, a lead/zinc, room-and-pillar mine near Bunker, MO. Cemented rockfill is being used to provide roof support as high-grade, remnant ore pillars are mined. Earth pressure cells and deformation meters placed in backfill panel pillars monitor stress change and vertical deformation, respectively, as nearby ore-bearing pillars are extracted. Similarly, biaxial stressmeters and borehole extensometers are used to monitor mining-induced stress change and deformation, respectively, in long-term support pillars. Data from these instruments indicate that when ore-bearing pillars were mined, stress was redistributed from support pillars to a backfill panel pillar. The data also indicate that the backfill and support pillars have remained stable for two years after pillar extraction was completed in the area. This research demonstrates the importance of using reliable instruments to document the geomechanical behavior of pillars and backfill. Gaining a better understanding of roof support and stress redistribution mechanisms is a fundamental part of NIOSH's goal to reduce and/or predict rockfalls, which are still among the leading causes of injuries in metal/nonmetal underground mines.

Jan 1, 2006

By Vincent A. Scovazzo

Benchmarking is a business management process that seeks improvement through the study and reapplication of practices conducted by industry leaders. This discussion presents objectives and organization of benchmarking applied to mining geomechanics. Similar procedures have been successfully applied to mining companies, laboratories, and research organizations involved in mining geomechanics throughout the world. Benchmarking is a structured process that allows an organization to learn from the "best" in the field. The objectives of benchmarking vary depending on the company's targeted areas for improvements. Typical goals include ground control cost reduction, enhanced safety, optimization of geotechnical staffing, development of state-of-the-art design procedures, or the adoption of the "best in the field" geotechnical data management. Once the objective of the study is established and the practices and procedures to be benchmarked are identified, a benchmarking team is formed from internal and outside specialists. Benchmarking in geomechanics is fundamentally different than in most other fields because of the effects of local geologic conditions and regulations, both of which must be understood by all on the benchmarking team, before a comparative analysis can be made.

Jan 1, 2000