Search Documents

By F. E. Harris

The United States produces about 30 percent of the world output of salt. Numerous deposits occur in widely separated areas, but the leading producing States are California, Kansas, Louisiana, Michigan, New York, Ohio, Texas, Utah, and West Virginia. Although no great amount of salt is produced at present in Pennsylvania, the potential sources in that State recently aroused a good deal of interest. The United States salt industry is highly organized; it comprises fewer companies than when small crude works with primitive methods and equipment eked out salt for local needs, but concentration of output brought about by modern inventions and methods of production has improved the quality of the produce greatly and accelerated production.

Jan 1, 1939

Jan 1, 2001

By D. Oyler

The National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Research Laboratory (PRL), RAG Pennsylvania and Strata Control Technologies of Australia collaborated in an intensive study of ground behavior, reinforcement performance, and stress redistribution at the Emerald Mine in Southwestern Pennsylvania. The study site was a longwall tailgate subjected to a severe horizontal stress concentration. Field measurements indicated that the stresses applied to the study site nearly doubled during longwall mining, resulting in roof deformations extending to a height of 4.8m (16 ft) above the entry. A computer simulation of the field site was conducted using FLAC-2D, incorporating a broad range of rock behaviors and failure mechanisms. Comparison between the measurements and the simulation showed that the model was able to capture the most significant aspects of the roof and support system behavior, particularly, the extensive slip along bedding that created a partially destressed "softened" zone in the immediate roof. The model also showed that supplementing the normal roof bolt support pattern with cable bolts would allow the entry to survive a further 20-25% increase in the applied horizontal stress. Such information could have very practical application to the design of roof support systems for coal mines.

By B. H. Good

This paper describes the research that has been conducted -in an effort to understand the nature and causes of sulphide fires -in the Sullivan Mine. Results of the investigation have led to several theories of the origin: of the fires, the nature of the chemistry and a method for assessing: the fire potential. Recommendations and the implications for the mining operation are also discussed.

Jan 1, 1977

By N. A. White

Whereas the ultimate world supply of energy minerals-defined as fossil fuels and fissile materials - is controlled by geological factors, the actual supply at any particular time is controlled by economic feasibility, technological innovations and /or political decisions. This paper identifies and discusses the principal uncertainties surrounding the international availability of energy minerals from now until the end of the century. A brief comparison is also made between energy and non-energy minerals. Genuine shortage s of energy minerals are now of a very long-term nature, whereas artificial ones may occur at any time and have a serious effect on the world economy due to the dependence of most OECD countries on imports of energy mineral . This paper argues that events over the last decade, such as the demand for a New International Economic Order, the OPEC increase in crude oil prices and the growing international lobby on environmental issues especially relating to nuclear safety - will progressively lead to a major, long-lasting transformation of the energy scene world wide. This transformation will encompass demand, in terms of conservation and efficiency, the supply mix of the various energy minerals , the supply system and the structure of the different energy industries . It is already affecting the role of governments and reaching into the question of national sovereignty both of developed countries, such as the U.K., Norway and Australia, and the developing countries, thereby making energy minerals a key area of international relations.

Jan 1, 1978

By A. C. Fieldner

ONE of the important functions of the Bureau of Mines is the, analysis of coal from every coal-mining State and Alaska. These analyses are being published for use of Government officials and the public. In connection with analytical data showing composition and quality of coals of the States, consumers, Producers, and the general public will be interested in a brief description of the geologic structure of the coal basins, typical mining conditions in the several districts, and the principal economic data of the industry. These publications have therefore heel) designed to include such features to present concisely the principal facts regarding occurrence, reserves, duality, characteristics, production, and uses of coals of each producing State.

Jan 1, 1952

By John Paul Gries

This Bureau of Mines report reviews the mineral industry of the Black Hills area, including Butte, Custer, Fall River, Lawrence, Meade, and Penning- ton Counties, S. Dak.; and Crook, Niobrara, and Weston Counties, Wyo. It includes discussion of geological occurrence, processing, and potential of 27 commodities that have been produced from the nine-county area. The value of mineral production exceeds $70 million annually. Gold and petroleum account for two-thirds of the total, followed by clays, cement, sand and gravel, and rock. The combined mineral industries annually consume 268 million kilowatts of electrical energy, 933 million Mcf of gas, and 2 million barrels of fuel oil. Water consumption is about 10,000 gallons per minute. About 2,700 persons are employed on a year-round or significant part-time basis.

Jan 1, 1974

By Kenneth R. Maser

This report describes a research and development program sponsored by the United State s Bureau of Mines. The purpose of the program was to develop reusable explosion-proof bulkheads for a cross-cut emergency shelter, and to study the implementation of such bulk-heads, and the resulting shelters, as part of an emergency escape plan in a normal coal mining environment. The first part of this report reveals a number of significant conclusions regarding the application of emergency shelters. A study of the cause s of, and the conditions prevailing during a mine emergency indicate s that ideal placement of the shelter s would be midway along developing entries, and at the inter section of butt and main entries. The proper spacing of shelters is based on the travel capability of trapped miners, which is in turn dependent on the height of coal. The life of a given emergency shelter, based on an analysis of the above information, will be anywhere from 6 months to 10 years. Consequently, some shelters are regarded as "temporary?, while others "permanent?.

Jan 1, 1975

By T. F. Myners

This paper, describing the concentration methods and costs of Witherbee, Sherman and Company at Mineville, N. Y., is one of the series of papers on milling methods and costs being prepared by the United States Bureau of Mines. It deals principally with the production of high-grade concentrate. ACKNOWLEDGMENT The author is indebted to C. F. Jackson, principal mining engineer, United States Bureau of Mines, to A. M. Cummings, general superintendent of Witherbee, Sherman and Company, and to the company's engineering staff, for assistance in preparing this paper.

Jan 1, 1932

By AIME AIME

I am happy to welcome you to the twenty-third conference of the National Open-Hearth Committee, and our joint conference with the Blast Furnace Committee, of the American Institute of Mining and Metallurgical Engineers. It is appropriate that, for our fifteenth year anniversary, we should meet in the hotel and the city where this Open-Hearth Committee was inaugurated in 1925. At that first meeting, only a handful of men from a number of steel companies met to discuss ways and means to start a movement to improve the practical and metallurgical technique of open-hearth operations among independent manufacturers, as the United States Steel Corporation had carried on for many years.

Jan 1, 1940

By O. H. Metzger

This is one of a series of capers being published by the Bureau of Mines on gold mining A the Western States. It describes the production of gold in the principal mining districts of New Mexico. The material was gathered red on a trip through tale State in the summer of 1936. ACKNOWLEDGMENTS The author acknowledges the aid and cooperation of mine operators in all parts of the State, who willingly contributed all information requested. Geological reports of the Geological Survey and the New. Mexico Bureau of Mince were drawn upon freely for information; credit to individual paper, is given in the text.

Jan 1, 1938

By Craig T. Jones, Zachary Q. Maassen

"Jet grouting is a method of ground improvement that relies on the erosive capacity of high-speed jets to cut and mix the ground in place with a cementitious grout. A continuous return flow of cuttings, called jet grout backflow or spoils, is expelled to the surface during the grouting process. Data from projects completed in Toronto and Ottawa is presented where BOS Solutions’ services provided significant savings compared to the traditional spoils treatment utilizing vacuum trucks for spoils disposal. These traditional treatment methods are cumbersome and expensive by nature. BOS Solutions provided an alternative solution that is environmentally friendly and capable of handling full flow to process these jet grout spoils utilizing a tank system paired with centrifuges and flocculation additives to remove the ground soils and grout product from the spoils slurry. BOS’ process produced a clean water for reuse in the project while reducing the overall waste volume by producing a dry, stackable solid that could be hauled to a landfill. Benefits observed by using the BOS process were disposal waste volumes decreased over 30% and at least a 19% reduction on disposal costs.SCOPE OF WORKJet grouting is a method of ground improvement that relies on the erosive capacity of high-speed jets to cut and mix the ground in place with a cementitious grout. A continuous return flow of cuttings, called jet grout backflow or spoils, is expelled to the surface during the grouting process. The backflow, or spoils, is a mixture of grout, water and soils. Traditionally, the spoil would be collected in in-ground pits and allowed to solidify for a few days prior to hauling to a final disposal site. For the projects completed in Toronto and Ottawa, the jet grouting work was performed at street level, in high traffic congested areas, presenting the challenge of insufficient space for the contractors to process the jet grout spoils in the traditional way. At first, attempts were made of using vacuum trucks to collect and haul the wet spoils to an off-site location where the spoils would be allowed to solidify. However, this method proved cumbersome and expensive due to the high volumes of spoils generated daily and the high number of vacuum trucks required to support the jet grouting operations, respectively."

Jan 1, 2017

By Serge Perreault

Le cuivre est un métal fascinant qui joue un rôle essentiel dans le développement des différentes civilisations depuis 7000 ans. Le cuivre est aussi un métal polyvalent et essentiel qui est très présent dans notre vie quotidienne. L’un des premiers métaux utilisés par les humains, il est un élément chimique qui se trouve à l’état natif, ce qui est rare pour les métaux. Il apparaît principalement dans des minéraux, notamment sous forme de sulfures, en raison de son caractère chalcophile (c’est-à-dire son attraction pour l’élément soufre). Le cuivre se trouve dans la croûte terrestre sous forme de minéraux de cuivre, tels que dans les sulfures dont la chalcopyrite, la bornite, la covellite et la chalcocite. Il est également présent sous sa forme native ou dans des minéraux oxydés comme la cuprite et dans des carbonates hydratés, comme la malachite et l’azurite. La formation de gisements de minerai de cuivre implique des processus géologiques complexes, notamment l’activité hydrothermale, les intrusions magmatiques et l’altération des roches. Les gisements de minerai de cuivre se trouvent dans divers types d’environnements géologiques, dont les gisements porphyriques, les gisements de cuivre encaissés dans des roches sédimentaires, les gisements de type skarn, les gisements de sulfures massifs volcanogènes, les gisements magmatiques de type nickel-cuivre, les gisements de cuivre oxydé, et d’autres [1].

May 2, 2024

By F. N. Flynn

- Introductory IN 1882, The Arizona Copper Co. Ltd., acquired producing copper mines at Metcalf and Morenci (locally called Longfellow). Metcalf is situated a distance of 7 miles, and Morenci a distance of 6 miles from the general office of the company at Clifton, Ariz. A reduction works with five blast furnaces was built in the center of the town of Clifton in 1884 and operated until January, 1914. Concentration of oxidized ores was begun in 1890-1891, in a mill built adjoining the smelter, and in October, 1893, a leaching process was started for treating tailings from the oxide mill. A sulphide concentrator with 300 tons capacity was built at Clifton and started treating chalcocite ores in July, 1896. This was the first mill to treat low-grade copper-sulphide ores successfully. Another concentration mill for sulphide ores was erected at Morenci in 1900. The, sulphide mills are now being remodeled to treat ores by concentration and flotation, with a capacity of 4,000 tons at Morenci and 500 tons at Clifton. The leaching plant has not been running since September, 1914. The average yearly production from this company's mines and reduction works from 1885 to date has been: Pounds 10 years ended 1894 6,864,902 10 years ended 1904 20,439,614 10 years ended 1914 : 32,665,905 Part of year 1915, to Sept. 12 30,206,106 4 months of 1916, to June 15,964,840 June, 1916...: ? 4,900,000 Construction on a new smelting plant was started in February, 1912, and finished in February, 1914. In the Transactions, vol. 49, E. Horton Jones published "Unit Construction Costs from the New Smelter of the Arizona Copper Co., Ltd:," which fully describes the construction of this plant, with details of costs.

Jan 9, 1916

By J. O. Merritt

The primary objective of this research program was to recommend ranges of minimum luminance for safety in underground metal and nonmetal mining. Visual tasks critical to safety were identified and rank-ordered. Realistic, full-scale, dynamic task simulations encompassing the most important visual components of the critical tasks were installed in a large simulated workspace. Five trained observers performed the six simulated mining tasks under varying levels of luminance. Over 13,000 measurements of visual task performance were used in developing minimum luminance recommendations for the on-foot underground worker and the mobile equipment operator.

Jan 1, 1983

By David Ziegler

Rough sketches, field notes, an on-site conference or a phone call may no longer suffice to establish your blast plan at a job site. More and more, general contractors, site supervisors, owner re p resentatives, or the owners themselves want to know details about proposed drill and blast operations at their site, in advance. We are seeing more contracts that re q u i re a blasting plan to be submitted in writing. The purpose of this session is to discuss items that you might want to include and address in a written blast plan, and some ideas about how to present them. This is not intended to be a complete list of items that could be included in a blast plan. Contracts may list specific items that need to be addressed. Only a few of the more common elements will be covered here. The bro a der purpose of this discussion is to get you thinking, about what you might want to include in your own “standard ” blast plan.

Jan 1, 2004

By J. Bongarra

This report describes the development of the instructional design and content of a training program for shaft construction miners and supervisors. The recommended training approach is based on the results of a needs, task, and competency analysis of the jobs performed by conventional shaft sinking and raise drill personnel. Learning objectives were derived from the task analysis and the appropriate training delivery system was chosen using a selection technique which employed learning algorithms. The training described is aimed at improving the safety and efficiency of constructing shafts by new hire and experienced miners and supervisors. A self-paced, self-teaching, modular approach to training, using criterion-referenced tests was proposed. Recommendation was made to divide the training into three parts: Orientation and Safety; Task Instruction; and Practical Exercise. Training requirements for conventional shaft sinking and raise drilling were described. Training program content was detailed in the form of module and lesson design approaches. In addition, the report recommends a method for developing, implementing and validating the training program. The authors conclude that such an implementation would meet the major objectives of improving the safety and efficiency of shaft construction work operations.

Jan 1, 1979

This report summarizes the work performed and results achieved on the above contract from October 18, 1971 through July 14, 1972 under Phase II, Task 1: Detailed Design of Prototype and Task 3: Supporting Experimental Investigation. Operation and Service Manuals resulting from Task 3 are submitted under separate cover as are detailed design drawings and specifications, prepared under Task 1. Both items accompany this report. This report also includes (A) an estimate of the cost of construction, (B) a description covering the use of the equipment, and (C) a proposed test plan to demonstrate performance of the equipment in both the laboratory and a mine.

Jan 1, 1972

During the extensive research which has been conducted in the Metallurgy Department of the University of Melbourne, into the properties of lead and its dilute alloys, the Brinell test has been used for the determination of hardness.The work described herein represents part of an investigation into the influence of various factors on such determinations, particularly when carried out on different qualities of "pure" lead. It is intended to publish the more theoretical and controversial aspects of this research elsewhere.MATERIALS USED AND THEIR PREPARATION FOR TESTINGThe tests to be reported have been conducted on a specially pure electrolytic lead, and several brands of commercially "pure" lead. The analyses of the samples upon which most of the work has been carried out are given in Table 1.Note: Oxygen was not determined, but from the work of H. W. Worner, in the Rosenhain Memorial Laboratory, it appears probable that it was approximately 0-0003% in all samples.

Jan 1, 1940

1.0 SCOPE AND REGULATIONS 1.1 This specification covers the minimum requirements for material handling and associated equipment including design and materials. 1.2 This specification requires compliance with all federal, state, local laws and regulations which may be applicable including the Occupational Safety and Health Act, Construction Safety Act as well as rules, regulations and standards of the Secretary of Labor.

Jan 1, 1979