Search Documents

By D. Xie

An in situ gravimetric technique based on wetting and capillary action principles has been used to investigate the wetting and penetration of synthesized alumina samples and commercial magnesia spinel refractories by CaO-SiO2-Al2O3-Fe2O3slags. Synthetic slags of 40CaO-40SiO2-20Al2O3 (in weight per cent) with 0 to 9 weight per cent Fe2O3were used and the experiments were conducted at temperatures 1370 to 1470ºC under argon. The contact time between the sample and the slag was 30 minutes. The results show that the wetting and penetration are enhanced by the iron oxide addition in the slags. Addition of Fe2O3from 0 to 9 weight per cent resulted in a significant increase in the slag penetration into the magnesia spinel refractory by a factor of about 7 and a moderate increase in the synthesized alumina by about 60 per cent. The addition of Fe2O3enhanced the wetting (??cos?, where ? is the surface tension of the slag and the contact angle between the slag and the refractory) by 5 to 18 per cent. An increase in temperature from 1370ºC to 1470ºC resulted in a significant increase in the penetration of a 6 weight per cent Fe2O3slag in the alumina and magnesia samples by a factor of4 to 5 and a decrease in wetting by approximately 30 per cent. Keywords: refractories, slag penetration, wetting.

Jan 1, 2004

By U. B. Kodukula

Attempts are made to evaluate the feasibility of using a water-injection cyclone for the concentration of iron ore fines. The separation characteristics of clay fines, containing large amounts of alumina and silica, from the iron values are discussed. The effects of critical variables, such as injection water rate, truncated cone diameter, spigot opening and vortex finder diameter, on the performance of a water-injection cyclone in terms of iron, alumina and silica grades; iron recoveries; and alumina and silica rejections are discussed. A set of 16 full-factorial experiments (24) was carried out to gain an understanding of the individual and interaction effects of the variables. The results indicate that classifying iron ore fines containing 63.0% iron, 2.5% alumina and 3.5% silica through a water-injection cyclone can produce concentrates with iron grades greater than 66.0% and alumina and silica contents less than 1.5% and 2.0%, respectively, at different study conditions. The achievable iron recovery values are greater than 88%, and alumina and silica rejections are more than 80% and 50%, respectively, within the specific study conditions. While the truncated cone diameter, injection water rate and spigot diameter influences the alumina rejection to a considerable extent, it is mostly influenced by the vortex finder diameter. The iron recovery and silica rejection values are mostly influenced by spigot diameter and truncated cone diameter. The effect of injection water on the concentration characteristics depend on the prevalent truncated cone diameter and spigot diameter conditions.

Jan 1, 2008

By Samer Sadek, David I. Smith, Wai-shing Lee, Jeffrey L. Rice, Avelino Alonso

INTRODUCTION East Side Access (ESA) Contract CQ028 is located in the New York City Borough of Queens. The contract involves construction of a 230-meter (760-foot) long open-cut excavation with a permanent deck supporting Amtrak yard tracks over a semi-circular TBM launch wall on the east end, and the 36.5-meter (120-foot) long Northern Blvd. Crossing on the west end. The Northern Boulevard Crossing will be mined under an existing New York City Transit (NYCT) five-track subway tunnel; Northern Boulevard, a heavily traveled five-lane truck route; and an existing NYCT three-track elevated line; connecting to an existing open-cut shaft adjacent to the existing 63rd Street Tunnel bellmouth. When completed, Contract CQ028 will provide access for future Manhattan and Queens tunnel contracts. The footprint of the open-cut was determined by the geometric requirements of the future Plaza Interlocking facility to be constructed within in another future ESA contract. See Figure 1. This paper discusses design risk mitigations for the key elements of the contract, namely the Northern Blvd. Crossing and the semi-circular TBM Launch Wall. PROJECT OVERVIEW The Metropolitan Transportation Authority Capital Construction Company—East Side Access Project for the Long Island Rail Road will provide Long Island commuters with direct access to Manhattan’s East Side via a new rail line between the Harold Interlocking in Queens and Grand Central Terminal in Manhattan. The project connects the unused lower level of the existing tunnel under the East River at 63rd Street to new connecting tunnels in Queens and Manhattan. Contract CQ028 Scope and Construction Schedule This contract consists of the excavation of an open-cut from the east side of Northern Boulevard, through an existing MTA-owned rail yard and into the western limits of Amtrak’s Sunnyside Yard. The contract will connect to a completed open-cut

Jan 1, 2007

By K. Oraee

The empirical rock failure criteria play an important role in predicting the mechanical behavior of rocks, since affecting parameters on the behavioral properties of rocks are complex and numerous. Usually the empirical failure criteria are obtained by statistical methods, namely by means of fitting the mathematical function onto the experimental data. For evaluation and verification of the results, however, the quality and accuracy of the fit must be considered. This paper studies the efficiency and accuracy of conventional empirical rock failure criteria using a new approach, which is based on the analysis of uncertainty amplitude on the constant parameters of each criterion. The approach adopted here, is based on the combination of some parameters such as Mean Squared Error (MSE), Root Mean Squared Error (RMSE), type of function, degree of freedom and the confidence level of constants. Correlation coefficient (R2) is then a comprehensive test and can be used effectively for comparison and accuracy of empirical rock failure criteria.

Jan 1, 2012

By W. T. Wertman

A research program to aid development of better and more efficient methods for producing petroleum and increasing its ultimate recovery from underground formations is an integral part of the work of the Bureau of Mines on conservation of the Nation's natural resources. Economic, efficient production of recoverable oil and gas from a reservoir depends to a great extent upon the best and most accurate information that can be obtained from a study of the reservoir rock and its fluid contents. Information on oil and water saturation is pertinent and essential in wildcat, extension, and pool wells for good reservoir operations and prediction of performance. This report presents results of an investigation by the Bureau of Mines of core recovery and degree of drilling-fluid contamination occurring during cable-tool coring operations using oil-base mud. Representative core samples were obtained from 6 major oil-producing sands in 8 fields of West Virginia, Pennsylvania, and New York. Field-mixed, oil-base drilling mud was used for the first coring test, and lightweight, premixed oil-base mud, with an organic chloride tracer added, was used in coring eight other wells. Tracer analyses were made to determine contamination of core by drilling-fluid filtrate. Core analyses, including oil and water content and minimum interstitial water-saturation tests, were made on selected core samples to compare and evaluate water saturations determined by the two methods.

Jan 1, 1958

By A. Taylor, M. Blanchette, J. Doucet

"A Z1600 Jameson Cell Test Rig was rented for test work at Vale’s Clarabelle Mill operation. This paper discusses the evolution of renting the unit for test purposes to owning the unit and operating it as a revenue generating process component. The paper focuses on three aspects of the Z1600 project; the initial rental and installation, the test work performed in the cleaning circuit, and the business factors which led to the unit being permanently incorporated into the copper circuit.INTRODUCTION Clarabelle Mill is located in Sudbury Ontario (approximately 350 km north of Toronto) on the southwest rim of the Sudbury basin a meteoric impact crater that is 62 km long and 30 km wide. The result of the meteoric impact was concentrated nickel (Ni), copper (Cu) and platinum group metal (PGM) ore bodies in the outer perimeter of the basin; described in more detail by Hanley (1957). Vale currently has seven operating mines in the Sudbury basin, from which nine distinct ore types are mined. Ores are also received from two QuadraFNX mines. Clarabelle Mill processes all of these ores for the Ontario Operations of Vale. The mill, commissioned in 1971, was originally built as one of four mills operated by then Inco Limited. Between the late 70’s and the early 90’s process changes were made to consolidate the Sudbury Operations milling processes into a single operating mill, Clarabelle Mill. In 1990, the SAG mill was installed resulting in peak mill throughput of 11.9 million short tons per annum (Mstpa), with typical throughputs of ~10 Mstpa. Mill average feed grades were 1.4% Cu and 1.2% Ni. During the resources boom, plans were developed to increase the mill capacity at Clarabelle Mill in stages to a final capacity of 13.5 Mstpa. The project known as the Clarabelle Mill Expansion and Recovery Project (CMERP) included expansion and reconfiguration of the grinding and flotation circuits. The first stage was a planned increase in grinding capacity with the reallocation of existing mills, the existing flotation capacity would be required to treat higher throughput until the new flotation circuit was constructed."

Jan 1, 2012

By Heikki Jalkanen

The mineralogical composition and morphology of solidified copper smelting and converting slags are of some interest from slag cleaning (by froth flotation), impurity elimination, and environmental points of view. Properties result from both the state of molten slag before solidification and processes taking place during solidification and cooling. In solidification and cooling, copper and sulfur dissolved in molten slag are .precipitating substantially from the silicate phase. Even in water quenching of slag, dissolved copper is pushed out of the solution in the form of finely divided precipitate. Elements present in the raw materials are distributed in a distinct manner between the solidified slag and non-silicate solidification products. Arsenic, antimony, and tin are strongly accumulated in copper precipitate, but not the other metallic constituents common in copper concentrates. Smelting and converting slags differ remarkably on their mineralogical composition and morphology although resulting principally of same chemical processes. Converter slags are more inhomogenous; they often contain solid particles and copper content is .as a rule higher than in matte smelting slags. The final copper content of converter slags was observed to be in a distinct manner dependent on iron oxide - silica ratio. Slag forming, solidification, and precipitation phenomena are discussed on the basis of mineralogical and morphology analysis of smelter slags and laboratory scale experiments.

Jan 1, 2002

By J. M. A. Geldenhuis

This work is concerned with studying possible reactions in the ilmenite furnace which may control the product quality of both slag and metal. Two different approaches were followed: comparing actual furnace slag compositions with the calculated equilibrium values and using commercial oxygen probes to measure the effective partial oxygen pressure in the slag and metal. It appears from a comparison of actual furnace slag compositions (in terms of the distribution coefficient of vanadium) with equilibrium values, that the TiO1.5-TiO2reaction may fix the effective partial oxygen pressure for the vanadium reaction. This possibility was tested using commercial oxygen probes (traditionally applied during steelmaking) to measure the effective oxygen partial pressure of both the slag and liquid iron in Iscor?s 3MVA pilot plant ilmenite furnace. From these measurements, it appears that commercial oxygen probes containing zirconia solid electrolytes can be used to measure the effective oxygen potential of both the slag and liquid iron. This oxygen activity correlates well with the FeO content of the slag. The results, furthermore, clearly illustrate that equilibrium conditions are not attained in the ilmenite furnace during the production of high titania slags, since the effective oxygen potential of slag and metal differ substantially.

Jan 1, 1999

A knowledge of the mechanics of wave propagation through the earth is essential if reliable communication systems are to be designed for coal mine environments. To obtain a reliable basis from which accurate propagation predictions could be drawn, a series of theoretical Studies have been prepared for the Bureau of Mines by Mr. Ramsay Decker of Spectra Associates, Inc. through a subcontract with Collins Radio Group. These reports formulate the analytical techniques from which wee may derive frequencies and antenna configurations that yield the optimum signal-to-noise ratios over the greatest distances in mine environments. The reports of sections 2 and 4 deal with analytical techniques for determining the signal-to-noise ratio within a mine environment for loop-to-loop and line source-to-loop antenna configurations. The analytical results of these reports were then implemented into computer programs to obtain predictions concerning through-the-earth signal propagation. These preliminary predictions are based on noise data compiled by Bensema, Maxwell and Stone, and WVU prior to the extensive research conducted by the National bureau of Standards (NBS). These initial measurements indicated a 20- to 30-dB lower noise level than that measured recently by N BS. The recent NBS data is that used by Collins in the final predictions.

Jan 1, 1974

By Israel Liebman

The Bureau of Mines conducted an investigation to determine those factors that are significant in affecting the velocity of flames propagating along the boundary separating gaseous fuel and air. In addition the aerodynamic motion of the gases in the vicinity of such interfacial flames was delineated. Parameters in the study included flammable zone thickness, flammable zone concentration of gradient, fuel type, and position of the flame relative to various environmental surfaces. Of all these factors, the flammable zone thickness and burning velocity of the stoichiometric mixture were found to have the most significant effect on the flame speed. Notion of the gases in the vicinity of the interfacial flames was examined by particle track and interferometric techniques. The relative velocity of the interfacial flame with respect to the unburned gas on the central streamline was found to equal the burning velocity of a stoichiometric homogeneous fuel-air mixture. In addition, it was observed that the composition of the lean fuel-air mixture at the boundary of the combustion zone appears to be less than that defined as the fuel's lower flammable limit.

Jan 1, 1968

By P D. Katsabanis

According to Persson(1) steady state detonation along a cylindrical charge can be regarded as a self propagating process in which the axial compressive effect of the shock front discontinuity changes the state of the explosive so that exothermic reaction sets in with the requisite velocity.

Jan 1, 1989

By E. M. Spokes

A.B. Rushton The work and resulting publications of the Committee on Underground Coal Mine Safety and The President's Commission on Coal were appropriate at the time of publication. The statistics cited in the publications appeared to be valid, and the actions proposed by the committee had merit. Although the actions proposed to achieve further improvements in safety may have been worthy of repeating, to associate statistics (Table 1) that are seven to eight years old with company names is bad. Statistics are readily available from the Mine Safety and Health Administration (MSHA) and are usually within three months of being up to date. A review of the most recent Coal Controlling Co. Report will reveal significant changes in the rankings. The more recent statistics should have been cited, or at least compared with those used in the article. Westmoreland Coal Co. is listed as having a 21.1 disabling injury rate for the period (1/78-12/80). The disabling injury rate for the Company for the year ending 1985 was 7.4 for the underground mines and 6.25 for the total facilities. Through March 1986, the disabling rate for the underground mines was 2.86. The management and employees of Westmoreland Coal Co. are committed to safety. The improvements achieved over the past five years attest to that commitment. We are justifiably proud of the achievement and dislike being misrepresented as in the April 1986 article. Reply by E.M. Spokes I regret that the lapse of time since the original work gives a picture of safety practice that is no longer true today. That Westmoreland has reduced its disabling injury rate by 65% to 7.4 in 1985 is most commendable, and I congratulate you for this accomplishment. It is typical of the progress sought by the National Academy of Science and National Research Council when they funded the original study and published "Toward Safer Underground Coal Mines" in 1982. If a significant number of companies do as well as Westmoreland, the report will have served its purpose. Since the paper was primarily a condensation of the original report, it would not have been appropriate to seek access to later statistics. The purpose in seeking its publication at the time of presentation was to reach those who might have missed the original report. The fact that publication was delayed has not voided that purpose and may have reminded some who were aware of the original that its recommendations still apply to improvement of underground coal mine safety.

Jan 6, 1986

By P. C. -H. Rhee, H. -G. Lee, J. -H. Choi, D. S. Kim, S. -B. Lee

In order to predict the composition of inclusions and to ascertain a method to prevent inclusions from forming in liquid Fe-16 mass Cr alloy, a thermodynamic database was developed through a quantitative determination of thermodynamic relationships of Cr-Al-Si-Mn systems in the liquid Fe alloys. Applications of the databases to the prediction of Mn/Si complex deoxidation with Alin Fe-16 mass Cr alloy were demonstrated in succession. The electromagnetic levitation technique using a cold crucible was employed to separate inclusions from liquid metallic alloys completely and to prevent any contamination from surroundings. Various interaction parameters in the liquid Fe-16 mass per cent Cr alloy system were determined; these are: [eAl(Fe)Cr= 0.19/T, rAl(Fe)O,Cr= -0.01, rAl(Fe)O,Cr= -0.00013, eS1Cr(Fe)= -0.38/T,rSi(Fe)O,Cr= 0.007, rO(Fe)Si,Cr= 0.0044, rA1(Fe)Si,Cr= -0.0075, rSi(Fe)A1,Cr= -0.0078, rSi(Fe)Mn,Cr= 0.005, and rMn(Fe)Si,Cr=0.01.] An improved database, utilizing interaction parameters for molten metal determined in this study, and the Fact Sage slag database of the MnO-SiO2-Al2O3-CrOx-MgO system were used for thermodynamic calculations. These were carried out under various thermodynamic conditions, and results were compared with experimental data of Si/Al, Mn/Si, and Mn/Si/Al deoxidation equilibria. With the abovementioned results, together with experimentally obtained data, thermodynamic conditions were determined, in particular Mn and Si contents, under which liquid inclusions form in liquid Fe-16 mass per cent Cr alloy. The critical Al content in liquid Fe-16 per cent Cr alloy, above which solid inclusion of corundum phase ((Al,Cr)2O3) formed, was as low as 10 ppm. This indicates that extreme care must be taken in controlling the Al content in the metal to avoid formation of solid corundum phase ((Al,Cr)2O3) inclusion. The compositional change prediction of inclusions, which originate from slag entrapment and by Ca addition, was demonstrated by use of the alloy database optimized through this study, and the Fact Sage oxide database. For Si-deoxidized Fe-16 per cent Cr alloy, high Si and low basicity of slag are effective to obtain liquid inclusions. For Al-deoxidized Fe-16 per cent Cr alloy, it is important to keep the Si content lower than 0.1 per cent and it is required to add Ca. Keywords: inclusion, thermodynamic simulation, deoxidation, Fe-16 per cent Cr alloy,stainless steel, interaction parameter, cold crucible

Jan 1, 2004

By Takuya Taguchi, Toshihiro Ogata, Atsuio Inoue, Shigeyuki Sasaki

Highly improved drilling machines and mucking machines have been used for the underground construction. To have rapid construction, the roles of blasting operation ha ve been growing more important. At the most tunneling of present, cartridged emulsion explosives have been used for a blasting in Japan. Under this circumstance, a blasting system of ANFO explosives using loading machine has been used recently for a tunnel blasting. However, ANFO has some problems, such as a useless explosives in wet boreholes, bad blasting fumes and the ammonia gas due to the decomposition of ammonium nitrate in contact with the sprayed concrete in tunnel.

Jan 1, 2005

By Najdat I. Aziz

There are different schools of thoughts about the influence of gas pressure on coal strength. Researchers have reached contradictory results with regard to the effect of confining gas pressure on tensile strength of coal. Accordingly, this paper re-examines the influence of gas pressure on the strength of coal. A specially designed precision drill capable of drilling in a pressurised chamber was used to drill coal samples under both atmospheric and increased gas pressure environment. The drill cuttings were examined for particle size distribution using a laser controlled Malvern Mastersizer S particle size analyser. Petrographic analysis of the sample examined the effect of gas pressures on the maceral structure and the composition of coal. The paper demonstrates that there is a definite variation in the range of particle size distribution with particles obtained from drilling coal samples not subjected to gas pressures, in comparison with those obtained from samples drilled under confined gas pressure. Also observed were the changes in the rate of drilling in soft coal obtained from geologically-disturbed zones compared with other coal samples. Some variation on the maceral compostion of coals were also observed in relation to increased gas pressures and gas type.

Jan 1, 1996

In a previous paper the author showed that silver considerably delayed the recrystallisation of lead after cold work. The effect of antimony on the rate of recrystallisation of distorted lead was studied next, and the experiments performed, and the results obtained, are described in this paper. Electrolytic lead was used as a standard of comparison.It was also used to make the lead antimony alloys.This electrolytic lead contained 0.0005% total impurities.It was prepared from commercial lead by fire refining, followed by electrolysis and finally by vacuum casting. The process was described in the previous paper and the description need not be repeated here. PREPARATION OF LEAD - ANTIMONY ALLOYS.The steps taken to procure pure antimony are outlined in the appendix. To make the lead antimony alloys a mother alloy was prepared thus:-A quantity of the antimony (it was received in the powdered form) was placed in a pyrex glass tube, which was closed at one end. The antimony was washed with hot hydrochloric acid (1: 1), then with more dilute acid, then with distilled water, and finally with absolute alcohol; it was dried by warming and evacu,ating the tube. This should leave the antimony more nearly free from surface oxides.The amount of antimony was determined by weighing quickly; the appropriate amount of vacuum-cast electrolytic *Research Fellow, Dept. of Metallurgy, University of Melbourne.

Jan 1, 1936

By Rimas Pakalnis, Andrea M. Ouchi, Thomas M. Brady, Mary M. MacLaughlin, Cristian Caceres, Paul Hughes

A major focus of ground control research presently being conducted by the Geomechanics Group at the University of British Columbia, Canada, in conjunction with the National Institute for Occupational Safety and Health’s (NIOSH) Spokane Research Laboratory, is the development of design guidelines for underground mining within weak rock masses. The study expands upon the span design curve for man-entry operations and the stability graph for nonentry operations developed at UBC by extending the application to weak rock masses. The original database has been augmented by weak rock mass information from mines throughout the United States, Canada, Australia, Indonesia, and Europe. The common factor in all of these mines is the presence of a weak back and/or walls. This paper expands on the North American database and how the design curves have been employed at mining operations throughout the world. The definition of a weak rock mass for this study has been defined as having an RMR76 under 45% and/or a Q-value under 1.0.

Jan 5, 2007

By J. Allaire, P. N. Muteb

The Meadowbank mine is operated by Agnico-Eagle Mines Ltd. and is located in the Kivalliq District of Nunavut in northern Canada. The process plant operates presently at a throughput of 11,500 tpd with gold grade varying between 2.9 and 3.6 g/t. The ore supplied to the process plant come from two different open pits and it expected to come from a new open pit early 2014. The ore is mid-hard materials so the feed size ore have a bigger impact on the throughput. The average gold recovery is 94.0% with about 15-30% of gold recover from the gravity circuit. The Meadowbank mine commissioning started in February 2010 utilizing a flowsheet consisting of one stage of crushing followed by primary and secondary grinding. The commercial production began in March 2010. During the commissioning several difficulties were observed to reach the designed throughput of 8,500 tpd. It was evaluated to insert a second stage of crushing. The insertion of the secondary crushing have two objectives, first to reach easily the process plant design throughput as well as to evaluated the mill capacity increasing. The process plant team evaluated various expansion alternatives eventually deciding to install a secondary crusher, increased the SAG and Ball mills motors capacities and maintain the rest of the process unchanged. Early 2011, with the improvement in the gold markets, decision was made to install the secondary crusher between the primary crusher and the primary grinding. The process plant continued to operate on the initial design until early June 2011. This paper presents the SAG mill throughput increasing from the designed tonnage of 8,500 tpd to 2012 targeted tonnage of 11,500 tpd, secondary crusher commissioning and the difficulties to operate in Canada Artic (Nunavut).

Jan 1, 2013

The title of this address was selected before I had an opportunity to consider in detail the matters that I would like to discuss. Accordingly, I chose a very broad subject-so broad indeed that it would be foolhardy for me to attempt to deal with more than a few aspects of it. I do not propose to touch. at all on the developments to date of our mining and metallurgical enterprises, beyond paying a sincere tribute'to the skill and enterprise of those who have established an international reputation for Australian mining and metallurgy. I would rather look ahead and discuss certain factors that will play a decisive part in the future development of our mineral resources. I do this in no dogmatic spirit, and I hope that my remarks may lead to discussions which will stimulate action where it is needed.In recent years my colleagues and I have been forced by circumstances to give consideration to problems in the fields of mining and geology, and in process metallurgy, which lie outside the scope of our own research work. People come to us with metallurgical problems because they know of no more appropriate place to go, and it is distressing to have to inform them that it is nobody's job to offer them advice and assistance. I want to suggest to your Institute that it should press strongly for the provision of properresearch facilities for the mining and metallurgical industries, such as aready exist in most enlightened countries. In such countries, those connected with the development of mineral resources are able to obtain information and advice from Geological Surveys, Mines Departments or Bureaux of Mines, which offer far more comprehensive services than are available in this country.Before discussing specific technical problems of the mining and minerals industries, I shall enunciate certain general principles that I believe should be followed in respect to the technical side of the development of all Australian industries. The problem can, I suggest, be considered in three parts-technical education production, and research. I shall confine my remarks mostly to the research aspect, for it is with this that I am most familiar.For the efficient development of any industry in Australia, it is essential firstly that We should learn what is going on abroad, and secondly that we should simultaneously conduct independent research. In the latter sphere the Governmeht'departments and the private companies' or groups of companies should have complementary functions, the former concentrating on problems common to a number of companies or industries, and the latter on their oWn individual problems. It is essential to the continued existence of Australian industry that both company and govern...

Jan 1, 1944

By Seal. Thom

Large heap leach operations around the world contain significant under-leached metal values that present recovery challenges to operators. The first challenge is to find the location of the highest inventory. High resolution resistivity ? has proven sensitive enough to detect such zones in the interior of heap leach pads to target treatment or re-leaching. Newmont Mining Corp. has adapted the high pressure fracturing technology, used in oil wells to stimulate select zones in heap leach pads to add reagents in 3-D for re-leaching, changing zonal chemistry for improved recovery and heap closure. High Resolution Resistivity ? is able to subsequently monitor injected solution flow and determine directional permeability during Hydro-Jex stimulation. The combination of these technologies has shown strong economic success, for selecting targets in the heaps and monitoring solution application. These technologies are now available to the mining industry for adoption.

Jan 1, 2008