Search Documents

By N. L. Hayward, V. H. Ness

In the past decade Australia has seen the development, construction and commissioning of three complex processing plants for the treatment of lateritic nickel ores. These have all been based on high pressure acid leaching (HPAL) for extraction of nickel and cobalt into solution, followed by solid liquid separation in a CCD circuit. However, flowsheets for separation and purification of the nickel and cobalt diverge markedly. The existing plants have been commissioned with varying degrees of success, with a variety of problems ranging from materials of construction to inadequate design. While the process problems are not insurmountable, there is much room for improvement. Currently there are several new HPAL plants at the feasibility or financing stage. All of these have adopted one of the existing flowsheets. Most of the enhancements have focused on increasing autoclave size. It is now time to assess the success and failures of the three existing plants and incorporate this experience in a design for productivity, efficiency and reliability. Towards this end, this paper discusses aspects of flowsheet optimization, materials of construction and engineering design.

Jan 1, 2001

By I. Liebman

Two triggered barrier systems and several extinguishing agents were tested against coal dust explosion propagating in the main entry of the Bureau of Mines Experimental Mine at Bruceton, Pa. One system used a high-pressure cylinder to propel the extinguishant; the second system used pressurized nitro-gas or Halon 1301 (CF3Br) in a low-pressure system to power the disperser. The relative efficiencies of the extinguishants were determined by compar¬ing calculated concentrations of the extinguishant clouds present in the mine during suppressing of the explosions. Results showed the following trend of increasing effectiveness: Purple-K (KHC03)<water<hybrids consisting of foam or water combined with Halon 1301<Halon alone. On a weight basis, water was two to three times as efficient as Purple-K, whereas the hybrids and Halon alone were only marginally superior to water. Maximum efficiency of an extinguishant is attained by high rates of discharge from the barrier and by minimizing the time interval between onset of discharge and flame arrival to that necessary for discharge. Both the high- and low-pressure barrier systems were demonstrated to be capable of suppressing coal dust explosions; however, because of the potential hazard of the former, the low-pressure system is considered to be the most attractive prototype.

Jan 1, 1979

By Staff

This U.S. Bureau of Mines publication presents the results of investigations into the fire and explosion hazards of oil shale rocks and dust. Three areas have been examined: the explosibility and ignitability of oil shale dust clouds, the fire hazards of oil shale dust layers on hot surfaces, and the ignitability and extinguishment of oil shale rubble piles.

Jan 1, 1989

By William E. Greenawalt

IN these days of special legislation for the benefit of various industries one might well consider one branch of human endeavor intimately associated with engineering-that of patents and patent litigation. It is estimated that 85 per cent of all industries in the United States are based directly or indirectly on patents. Most inventors are engineers, and most patent litigation pertains to the engineering industries. It is fitting, therefore, that engineers should be vitally interested in discussing patent affairs, particularly as inventors are not a professional group, and invention is mostly a transitory phase incident to the development of specific industrial problems.

Jan 1, 1937

By William Wilkinson, Vladisla Kecojevic

Current three-dimensional (3D) computer design technology leveraged into drill and blast planning and operations is changing the way engineers and operations approach drill and blast design. Additionally, Global Positioning Systems (GPS) technology that is now readily available to the civilian population is being implemented into the mining sector with a variety of new products specifically designed for drill and blast operations. The objective of this article is to discuss the steps involved with 3D Computer-Aided Design (CAD) of drilling and blasting, and the benefits such a design can provide in conjunction with GPS and drill monitoring systems.

Jan 1, 2004

By A. Paviani

The subject of this session is "Equipment Installa­tion, Recent Developments". This is a subject which is not usually addressed at conferences of Foundation Engineering. It is rare to find sessions dealing with the technological side of deep foundations, a subject which only recently seems to have aroused sufficient interest at national and international conferences. It is therefore natural for the subject of "Equipment", or the tools used to implement the various "technologies", to be over­looked or mentioned only occasionally during the discussion of other issues. At conferences, most of the attention is attached to research and to the theoretical interpretation of the performance and behaviour of deep foundations, as well as to establishing the most suitable calculation algorithms and approaches for the study, design and control of foundation structures. It is almost as if the subject of equipment is felt to be less important or, perhaps, that it is considered to belong more strictly to mechanical engineering than to civil engineering.

Jan 1, 1994

By Huang Kai

By adding the solid oxalate acid powder into the solution of nickel chloride or its ammonia coordinated solution, the uniform compound particles were prepared and the precipitated particles were transferred to the mono-dispersed NiO particles by calcination. In this study, the various experimental conditions were investigated, the characteristics of the corresponding obtained particles were analyzed, and the formation mechanism of the particles was elucidated. It was found that the solid oxalate acid provided the solid-solution interface for the precipitation and induced the nucleation and growth of the product particles.

Jan 1, 2005

By Richard R. Marston, Scott Herr, Steve Pries, Donald L. Jr Ewart

The purpose of this paper is to identify and examine alternative methods (other than shovel/truck stripping) of effecting the pre-stripping of consolidated overburden, in conjunction with dragline stripping operations, at surface coal mines. The analysis will be case study oriented with practical mining considerations and comparative economics being evaluated. Alternatives that will be examined include blast casting, dozer push, and multiple pass dragline sequences.

Jan 1, 1992

By R. L. Levens

The Underground Injection Control program was promulgated in 1981 by the U.S. Environmental Protection Agency under the provisions of the Safe Drinking Water Act. Placement of mine waste backfill underground is considered underground injection under the provisions of this program. A major issue is whether mine waste that is regulated as a contaminant source on the surface should be disposed of underground. The U.S. Bureau of Mines conducted research to investigate the impacts of mine waste sandfill on the quality of ground water. Analyses of water samples collected before and after contact with sandfill in a 10-year-old stope, as well as samples of the sandfill itself, were used to ascertain the influence of the sandfill after mine closure and subsequent flooding. Computer models supported the hypothesis that oxidation of pyrite by oxygen, accompanied by dissolution of carbonates, was the predominant reaction controlling the quality of the water being discharged from the stope. Concentrations of metals released as a result of acid production remained near or below detection limits. Metals release after mine flooding is expected to remain low as a result of the buffering by the sandfill and the reduced rate of oxidation.

Jan 1, 2010

By J. M. Menacho, J. M. Reyes

"Batch and continuous regrind tests were conducted in 3 kW and 15 kW tower mill units, respectively. Single particle size classes of a chilean copper sulphide concentrate were employed in the batch tests, while a fraction of the plant stream was deviated to the continuous unit operated under different conditions.Results are interpreted in terms of the simplified grinding kinetic model energy-based and conveniently adapted to this application. Based on the above figures plus some industrial data supplied by MPSI Inc., a scale-up relationship was developed for the apparent specific rate of breakage siE, as a function of the net power draw P, i.e.siE = siE text (P/P test) 0.089This equation fit very well the available data at the three scales and its application to regrind 4400 t/day of rougher copper concentrate from 70% below 325 Tyler mesh to 95% below same mesh, involves around 30% energy-saving compared to standard ball mill for same grinding task.INTRODUCTIONImpact and abrasion-attrition breakage are two extreme mechanisms present in any grinding system in a proportion defined by specific design and operating conditions. Impact breakage is generally efficient for coarse grinding, while abrasion-attrition is adequate to produce fine particles. Efficiency of conventional tumbling mills decreases as fineness of the product increases, even though distribution of applied stresses is always much stronger than internal force distribution in the particles. On the other hand.in a vertically stirred ball mill like the tower mill, distribution of applied stresses and particle strengths are in the same order of magnitude, making possible nearly ideal abrasion conditions (1).Tower mill configuration includes a cylindrical body vertically mounted and provided with a central screw with flights to produce circulation of balls moved up through the inner region to return down by the external space. Fresh material can be fed into the top , center or bottom in order to assure appropriate agitation of suspended particles. Size reduction and evacuation rates should compensate settling of coarse particles to avoid sanding of the screw. Detailed description of the tower mill and its operation have been given elsewhere (2),(3)."

Jan 1, 1989

By William A. Beck

This report describes the loading and transportation practices employed at the zinc-lead mines of The Eagle-Picher Co., Jo Daviess County, Ill., and Lafayette County, Wis. The report also gives a brief history of the Illinois-Wisconsin zinc-lead district and the operations of the company in the area. The diesel-powered, rubber-tired loading and haulage equipment is described and illustrated from the operational point of view only, and an analysis is made of the materials-handling system without going into health and safety factors. The costs per ton of the various components of mechanical loading, underground haulage, underground crushing, and hoisting for fiscal year 1960 are tabulated.

Jan 1, 1964

By Denis Thibodeau

his paper describes a study of an altered mining extraction and the resulting Rockmass response at VALE?s Creighton Mine. Typically, the deep mining zones have strict stope extraction guidelines to ensure safety and productivity; however, these guidelines offer low flexibility or few options for stope sequencing. The 402 O. B. being in a good rock mass, at moderate depth and stress regime at Creighton, offered an opportunity to drive a more flexible mining sequence with stopes and a pillar. A three-phased approach was used to mitigate risk of the mining plan: 1- Numerical modelling to fully anticipate rock mass response to the proposed mining sequences. 2- In situ seismic monitoring to collect stress and seismic activity data. 3- Analysis of the in situ data to correlate to the modelling results. The creation and the extraction of a pillar in the 402 O. B. was successfully completed. The recorded seismic activity agrees well with the numerical modelling since most of the seismic activity is localised in the hangingwall where the deviatoric stress corresponds to an early damage process. The moderate levels of deviatoric stress cause localised failure with low level of seismic activity.

May 1, 2013

By G. B. Harris, A. R. Laplante

Fine tungsten was used to mimic gold and fine and coarse silica and magnetite to mimic gangue. The optimum flow rate of fluidisation water varied from 1.7 l/min for fine silica to 5.6 l/min for coarse magnetite. Overloading at optimum flow rate was then investigated. With fine silica gangue no overload occurred under any of the conditions studied, and there was very little overload with fine magnetite. Coarse silica caused appreciable overload, but only after a significant bed of tungsten had been formed; with fine magnetite gangue the onset of overloading occurred earlier. Finally, with coarse magnetite severe overloading occurred almost immediately. Overloading was modelled using a first-order kinetic rate constant for erosion of the concentrate bed and a critical mass of constant above which it takes place. The results clearly demonstrate the importance of removing oversize to maximise recovery, particularly with a high-density gangue

Jun 18, 1905

By T. Freeman

In the past ten years, the Geotechnical Baseline Report (GBR) has arguably become the key document for tunnel construction. This report not only allocates much of the risk involved with the work, it serves as the basis for bid preparation and is used extensively in resolving disputes during construction. This paper discusses some important issues related to the GBR and presents suggestions for improving these vital reports.

"Mineral separation by exploiting the differences in mineral or metal specific gravities (sg) has been used since antiquity. In the modern era, this is most commonly seen in the recovery of gold by the use of centrifugal concentrators and the separation of coal (low sg) from waste rock (high sg) using heavy media cyclones and jigs. Other metals, notably oxides of tin and tungsten, are successfully recovered using some combination of jigs, spirals and shaking tables. However, many conventional gravity separation systems are limited to fairly coarse (>1 mm) to medium (>100 micron) particle separations due to the limitations of the gravitational separation forces in conventional equipment.Many of the high specific gravity minerals of interest are friable (e.g. cassiterite, wolframite, etc.) and excessive fines are generated in the grinding/comminution circuits which cannot be recovered with conventional equipment and may be lost directly to the tailings stream. Recent developments in centrifugal gravity separation equipment specifically designed for fine or ultra-fine particle separation and recovery have resulted in heavy mineral particle recoveries as fine as 10-20 microns. Ongoing research work has also identified the benefit of closed-circuit, multi-stage gravity recovery circuits using some combination of centrifugal concentrators and conventional equipment (tables, spirals, flotation, etc.) which can substantially increase overall plant recovery and final concentrate grade.This paper will provide details of the evolution of non-fluidized bed gravity concentrators for high sg mineral recoveries, correlate laboratory scale development work with plant results to confirm scale-up, and show how recent flowsheet developments have contributed to significantly improved plant performance.IntroductionGravity concentration is one of the oldest and most cost effective metal and/or mineral recovery systems, ranging from the classic hand panning of alluvial gold, through to the large scale production of a wide range of metals and minerals, including gold, silver, PGMs, black sands, coal and iron oxides. Conventional gravity recovery systems, comprised of some combination of sluices, spirals, jigs and shaking tables have limited application in fine particle (i.e. <100 microns) recovery, or where there are limited differences in particle specific gravities (sg), e.g. the separation of high sg, high value metal oxides (e.g. those of tin, tantalum or tungsten), from medium sg, lower value metal sulfides such as pyrite and pyrrhotite. These unit operations tend to have limited capacity, and while double and triple turn spirals and multi-deck tables have been developed, extensive floor space is often required in order to process the tonnages incorporated in the modern mineral processing plant."

Jan 1, 2017

By D. M. MacHunter, T. Lawson, D. K. Henderson

The development and commercialization of new generation high tension electrostatic separators has provided a basis for simplifying mineral separation plant circuitry. The inclusion of new design features including insulated plate electrodes that have resulted insignificantly improved separation efficiencies in electrostatic separators are described. The increase in separation efficiency has resulted in a reduction in the number of treatment stages required to produce final high grade mineral products. Comparative performance data on different feed types are presented. A comparison between mineral separation plant flowsheets using both conventional and new generation high tension electrostatic separation technology is presented. A 55% reduction in the number of installed electrostatic separators and a 36% reduction in plant area was achieved through the use of this new electrostatic separation technology.

Jan 1, 2003

By D. Babich, L. Alcorn, E. Spencer, A. Smith

Noise is one of the most pervasive health hazards in mining. A compilation of Mine Safety and Health Administration (MSHA) noise survey data for Fiscal year 1990 shows that approximately 40% of the total samples taken for longwall occupations exceeded the Permissible Exposure Limit (PEL) of 100% [Gigliotti et al. 1991]. In order to properly determine workers’ exposures on longwall coal mining systems, it is necessary to provide accurate baseline measurements for these mining systems. This research was designed to develop guidelines and test procedures for identifying all noise sources that are major contributors to the underground noise exposure of longwall coal mining system workers. Once the high noise sources are identified, promising engineering controls can be tested and evaluated to reduce the noise of the sources. The measurement system used to analyze the noise sources included stationary dosimeters in a documented repeatable pattern and a time-motion study of the cutting cycle and operator’s work cycle. Significant results from the underground measurements show that the highest sound levels recorded are at the stageloader discharge segment and tailpiece controls and remained at about the same level throughout the test.

Jan 1, 2007

At the exploration stage for new mining projects or for medium- and long-term areas of existing mines (typical of South African gold mines), drilling data is on a relatively large grid. This grid is normally larger than the selective mining units (SMUs). Direct estimates for the SMUs and also of much larger block units will then be smoothed due to the information effect and the high error variance. Any capital-intensive project decisions made on the basis of any of the smoothed estimates will tend to misrepresent the economic value of the project or operation, i.e. the average grade of blocks above cut-off will be underestimated and the tonnage overestimated for cut-off grades below the mean grade of the orebody. This paper presents a direct approach technique for deriving recoverable resources, referred to as localized direct conditioning (LDC), designed to correct smoothing effects and also to provide support corrections.

Jan 1, 2014

Underground coal mine tracked vehicles have been studied to determine the state of the art and how brakes might be added to the coal haulage cars. Specific areas of interest are: brake sys terns, couplers, car trucks and car handling procedures. Problems related to adding brakes to the haulage cars appear to be: the limited amount of room to mount the brakes on the cars, brake line connection between rotary dump cars, achieving desirable braking characteristics without over complicating the system and keeping the installation cost to a reasonable figure. This document combines the information contained in the first issue of the "State-of -the-Art of Underground Coal Mine Tracked Vehicle Brake Systems," BRL Report No. 6080, with that contained in a subsequent monthly report.

Jan 1, 1973

By Olli Aulio, Outokumpu Oy

"GENERALThe Outokumpu Company is today an important European producer of metals from its own mines: copper nickel cobalt, ferro chrome and zinc being the main products. In 1972 about 4 million tons of ore was hoisted from eleven mines.Outokumpu Oy has gained experiences on the various aspects of on line computer control since 1968. This knowledge has been combined to develop a standard computer control package for concentrator control. Before the development of computer control package was started Outokumpu Oy had three large computer control systems. The first system was at the Pyhasalmi Concentrator, thee second at the LokkolaPlant, and the installation of the third system at the Vuonos Concentrator was just started.The characteristics of general computer software packages - both control and executive ones - were thus well-known as well as the practical usage of control theory. Furthermore Outokumpu had developed the Courier analyzer which included a so-called minicomputer. This project had given experience both 1n totally self made real tire executives and in computer hardware and peripheral d=vices. The instrumentation of the Outokumpu concentrators was designed and installed traditionally by the engineers of Outokumpu themselves."

Jan 1, 1973