Search Documents

By A. G. Pasamehmetoglu, N. Celebi, K. Erarslan

A deposit evaluation system has been developed for a proposed new mine in the basin around Collolar in Turkey. It includes compositing, gridding and reserve estimation facilities and takes account of the economic value of the pit and the pit bottom elevation

Sep 1, 1991

By P. Golledge, A. D. S. Gillies

An investigation has been carried on samples of three Queensland coal dusts to determine the potential explosibility of dust-gas mixtures. The explosion potential of the samples was classified by the lean and rich limits of explosibility and the limiting oxygen concentrations for each sample. Plotting of these points showed 2-dimensional flammability limit surfaces for coal dust/oxygen, methane/oxygen and coal dust/methane mixtures. From these plots the 3-dimensional flammability envelopes defining the explosibility of the mixtures were defined. The explosion limits of the coal dust/methane/oxygen system were seen to be influenced most by the explosibility characteristics of coal dust. Methane exerted a stronger influence over the explosion limits when the coal had a low volatile content

Jun 19, 1905

By Thomas D. Kelly

In 1900, the average U.S. citizen’s average life span was 47 years. He traveled about 1,900 km (1,200miles) in a lifetime and resided in a home with an ice-box for food storage and oil or gas for lighting. He communicated by mail, telegraph and crude telephones with limited availability and range. By 2000, the average citizen’s life span was 77 years. He traveled an average of 19,000 km/a (12,000 miles/year) by automobile alone. He resided in a home with many electrical appliances, including refrigerators and electric lights. And he communicated almost instantaneously with any other part of the globe by several widely available means, including portable phones and e-mail.

Jan 1, 2002

By B. M. Larsen, J. W. Campbell

Several articles have recently been published discussing the conditions necessary for accurate measurements of temperatures in the open-hearth steel furnace. In the course of a study of refractories service conditions in steel furnaces, the present writers have taken temperatures in several open-hearth shops in the Pittsburgh district. The conclusions, as to conditions necessary for accurate measurements of temperature, are somewhat at variance with those of other investigators. The subject is closely connected both with the close control of steel-making and the prevention of overheating of the silica refractories used in roofs and walls. It is becoming more and more important to obtain furnace temperatures of fairly definitely known accuracy. At present, the most useful instrument for such measurements is the disappearing-filament type of optical pyrometer. This method of measurement has formed the basis of most other discussions on the subject and was also used by the writers. Previous Investigations In 1916, Burgess' made perhaps the first systematic series of measurements in steel furnaces. The emissivity figures of 0.40 for liquid steel and of 0.53 to 0.65 for liquid slags had been determined by the Bureau of Standards and were used by Burgess in this work. These correction factors are still being used and are regarded as fairly accurate, so that the tapping and teeming temperatures on metal streams given by Burgess should be very nearly correct. Most of his temperatures of furnace roofs and slag surfaces were taken while flames were present in the furnaces and include a few roof temperatures above 1700' C. (3100' F.).

Jan 1, 1927

By N. Kinoshita, Y. Inada

The authors have proposed and discussed storage of low temperature materials such as LNG, LPG and frozen food in rock caverns. In this case, as the rock mass around the caverns will receive effects of low temperature, it is necessary to consider the thermal behavior and the stability of caverns. In this study, strength and deformation characteristics obtained by the uniaxial tension test and the compression test at low temperatures were discussed. Using the results, temperature and stress distribution around caverns when LNG was stored, were analyzed. Then thermal behavior of the rock mass around caverns was discussed. Die Autoren haben Lagerung von Niedertemperatur-Materialien wie LNG, LPG und tiefgefrorenen Nahrungsmitteln in Felskavernen vorgeschlagen und diskutiert. Da in diesem Fall die Felsmasse um die Kavernen den Effekten der niedrigen Temperatur ausgesetzt ist, ist es erforderlich, das Thermalverhalten und die Stabilität der Kavernen zu berücksichtigen. In dieser Untersuchung wurden Stärke-und Deformationseigenschaften, die durch ein-axialen Spannungstest und Kompressionstest bei niedrigen Temperaturen erhalten wurden, diskutiert. Mit diesen Ergebnissen wurden Temperatur- und Stressverteilung um die Kavernen bei Lagerung von LNG analysiert. Dann wurde das Thermalverhalten der Felsmasse in der Umgebung der Kavernen diskutiert. Les auteurs proposent et discutent l'entreposage de matériaux à basse température, tels que le GNL, le GPL et des aliments congelés, dans des cavités rocheuses. Comme, dans ce cas, la masse rocheuse entourant la cavité subit les effets des basses températures, il est nécesaire d'étudier le comportement thermique et la stabilité des cavités. Dans cette étude, les auteurs discutent des caractéristiques de résistance et de déformation, obtenues par essai de tension uniaxial et essai de compression à basse température. En se servant des résultats, ils analysent la répartition de la température et des pressions autour des cavités, lors du stockage de GNL. Ils discutent ensuite le comportement thermique de la masse rocheuse autour des cavités.

Jan 1, 2003

By J. A. Woolf, E. S. Leaver, A. P. Towne

"INTRODUCTION A report giving experiments dealing with factors affecting the floatation of the most commonly occurring silver minerals was published years ago. At that time we could not obtain suitable samples of many of the so-called sulfo-salts of the base metals, which are generally silver--bearing and which comprise an appreciable percentage of the natural silver ores. Since Leaver and Woolf's work was published, samples of impure tennantite and enargite have been obtained, and considerable experimental flotation work has been done with synthetic mixtures prepared from these samples. During the present national emergency, research dealing solely with the recovery of gold and silver must necessarily be curtailed. However, many deposits of strategic minerals and critical base metals contain an appreciable amount of gold and silver, the recovery of which would aid greatly in recovering the strategies by taking care of a considerable part of the cost of treatment. Because of this, the recovery of precious metals should not be overlooked entirely. As the Bureau of Mines is now utilizing all of its facilities for the development of increased domestic productions of strategic and critical minerals, this is the last report not concerned primarily with such minerals that will be published until the war ends."

Sep 1, 1942

Willyamite from the type locality, Consols mine, Broken Hill, N.S.W., has been re-examined, and found to consist of zones with widely different Co:Ni ratios. The name willyamite is redefined to include the portion of the (Co, Ni)SbS series with cobalt in excess of nickel. Willyamite is pseudo-cubic, with the three axes equal to within 0·001 A.

Jan 1, 1970

By K Niyomjinda, B Etschmann

Chatree Gold Mine is currently the only modern day gold mine operating in Thailand, and is situated approximately equidistant from Chiang Mai in the north and Bangkok in the south. Environmental guidelines set by the Thai authorities require Chatree Gold Mine to achieve a Total Cyanide level of 20 ppm or less in the process plant discharge slurry stream prior to release into the tailings storage facility. This paper describes both the initial difficulties faced in achieving compliance on this limit utilising the conventional INCO SO2/Air cyanide destruction system and the subsequent process improvements initiated to both the leaching process and the standard INCO process to achieve the current compliance levels of approximately 99/100 shifts. Improvements were focussed on the dual aspects of reducing the formation of WAD cyanide and ferrocyanide species in the leaching circuit coupled with process changes to improve removal of the ferrocyanide species from solution during the cyanide reduction stage.

Jan 1, 2004

By Rudy Scarabelli, John R. Wagner

At one time explosives were the only economical means of rock tunnel excavation. Except in relatively long tunnels in the right rock explosives are still the cheapest means of rock excavation where they can be used. Today the most economical means of rock tunnel excavation is increasingly not the choice of the contractor. A good part of our work is for public agencies in urban areas and the public today is increasingly less tolerant of the disruption caused by our efforts. Owners in many cases have to direct their engineers to write specifications which severely restrict noise and vibration levels during construction. Sometimes specifications allow drill-and-shoot for starter tunnels only or even eliminate powder by fiat. Recent advances in the use of explosives such as sequential firing have made blasting more palatable to the public but are not enough in all situations. Thus the roadheaders on construction projects. In recent work I have seen the Alpine Miners, a Paurant Miner and the Robbins Mobile Miners used in several rock formations and now believe this type of equipment has a place in the tunnel constructor's choice of equipment. Rudy and I have not attempted to present a formula for choosing the best alternative excavation method in any given case because, of course, of the variables involved. We have simply tried to describe our experiences on a particular project and hope our observations will be of some value to tunnel constructors.

Jan 1, 1987

By B. J. Kloppers, J. V. Z. Visser, C. J. Horn

"The long-term plan (LTP) in a mineral resource company is defined by the quality of the mineral resource and represents the result of a series of trade-offs to fulfil internal organizational as well as external business and legislative requirements, ensuring ultimate delivery on the defined organizational strategy.The LTP should as a whole align to a coherent and well-defined organizational strategy, working towards a clearly defined objective while still allowing a tactical response to short-term requirements of the organization. The ability to respond tactically to changes in environment, like the unprecedented five-month strike in 2014 on the platinum belt following the 2012 Marikana incident, is a measure of the flexibility of the plan given the agreed strategy.This paper describes the Lonmin process of linking company strategy with long-term planning, tactical planning, and the execution of the plan through an annual planning cycle to maximize organizational flexibility. This flexibility enables mining companies to respond to the many internal and external forces that impact on both strategy formulation and delivery of results that meet shareholder expectations."

Jan 1, 2015

By B. Stimpson, K. Kosar, K. Barron

"A number of high wall failures have occurred in some of the Alberta coal strip mines of a type called by the authors ""Multiple block plane shear slope failure "". They cause rapid deterioration of the dragline bench, reduced productivity and maintenance costs.The failures are invariably associated with the presence of almost horizontal (± 5 degrees) bentonitic clay bands in the overburden, often immediately above the coal seam, and regress behind the slope as a series of tension cracks which isolate detached blocks. As many as 17 sets of cracks have been observed, at lateral distances in excess of five times the slope height from the toe.The theory of this mode of failure is presented and a limiting equilibrium computer program which will produce deterministic or probabilistic (Monte Carlo) solutions is briefly described. A case history of one such failure is documented. It is shown that the extent of the regressive failure is exceedingly sensitive to the water table elevation, leading to the conclusion that drainage, if practical, represents the best control strategy. IntroductionA number of high wall slope failures are occurring in some of the coal strip mines in Alberta of a type called by the authors ""Multiple block plane shear slope failure""(I). These failures cause a rapid deterioration of the bench from which the dragline operates, reduced productivity, and necessitate conregresses into the slope as a series of tension cracks and detached blocks. As many as 17 prominent cracks or crack zones have been observed, the last being in excess of five times the slope height distant from the toe.The block between each pair of cracks must be at limiting equilibrium, i.e. the factor of safety equals one. This condition can be used to determine the locations of the cracks which develop in sequence behind the face."

Jan 1, 1986

By Bruno Gemmi

A new warehouse built with prefabricated components over an area underlined by soft marine soil deposits started showing differential settlements well before its completion. Its 103 spread footings carrying up to 4,000kN (450t) axial loads had been cast on jet-grouted columns extending and penetrating a layer of sand at a depth of 10m (33ft). Investigations performed to assess the wholeness and consistency of the jet-grouted columns revealed a state of loose jet-grouted masses and uncontrolled, off target migrations of the jet-grouting. Most of the jet-grouting itself was settling. The following remedial solutions were suggested: 1. Construction of new and better controlled jet-grouted columns. 2. Cement-based soil grouting. 3. Expanding resin injections. 4. Minipiles drilled-through the existing footings and reaching into a denser layer of sand existing at 23m below grade. Remedial solution 1. was immediately discarded due to cost and the possibility of a repeating failure in this non-granular and highly compressible soil. Tests of remedial solutions 2. and 3. were carried out. The outcome of the grouting was monitored by Electro Resistivity Tomography (ERT) (Bares et al., 2003), an innovative 3D electro tomography procedure showing where grout had been actually placed and its migrations off target. A successful 4,000kN (450t) load tests confirmed the validity of the solution. Finally, upon the completion of a successful load test, solution 4. was chosen. It supplied the highest degree of reliability thanks to the ease of controlling the final and actual location of the minipiles and to the higher safety factor provided. All remedial work to install the minipiles was eventually performed inside the building. Additional load tests and settlement measurements confirmed the adequacy and success of the chosen solution.

Jan 1, 2011

By Shahram Tafazoli

This article presents a novel technology for sensing the size of rocks after blasting in hard rock mines. Blast engineers require rock size statistics to carefully adjust the blasting parameters. The rock fragmentation requirements vary depending on the ore type and crusher specifications. The most popular statistical parameters in the industry are the so-called P numbers (e.g., P80 and P100). A machine vision based system is introduced here for automatic image collection and fragmentation analysis of the material right inside the bucket or dipper of mining shovels. A heavy-duty camera provides the required imaging data to an embedded computer mounted inside the cab. A custom machine vision software continuously analyzes the captured bucket images and stores the suitable ones in local storage which are then fed to a Desktop software for automatic fragmentation analysis. This technology has been developed by Motion Metrics International and is commercially available as FragMetrics?.

May 1, 2009

By C. Musingwini, A. S. Nhleko

"Since the Global Financial Crisis (GFC) in mid-2008, capital has been more difficult to access. Mining projects must contend with projects from other industries for scarce capital. A decision to invest available capital in mineral projects requires that valuation be conducted to assess the expected return on the projects. The discounted cash flow (DCF) analysis is generally applied for the valuation of mining projects, whereby future cash flows are discounted to present value using an appropriate discount rate. The discount rate significantly affects the outcome of a valuation. Economic and finance theory provides tools to calculate discount rates. The discount rate must account for factors such as the risk and stage of development of the mineral project; hence the appropriate discount rate to utilize in a project is often a subject of debate.The discount rate is the weighted sum of the cost of debt and equity. There are several methods for determining the cost of equity. This study considers the commonly applied Capital Asset Pricing Model (CAPM) and Gordon’s Wealth Growth Model because of their simplicity and availability of parameters required to estimate the cost of equity. This study explores how differences in the cost of equity obtained by these two methods can be explained for a mining environment. Data for empirical analysis were collected from the I-Net Bridge, McGregor BFA, and Bloomberg databases. It was found that Gordon’s Wealth Growth Model provides better estimates of the cost of equity compared to the CAPM under depressed market conditions. Therefore, this research recommends that Gordon’s Wealth Growth Model be used to estimate the discount rates for mining projects during periods of depressed market conditions."

Jan 1, 2016

By Rick Moignard

Relationships between Information Technology providers and their clients are often segmented according to job specific tasks. As a consequence, technology providers tend to focus on automating repetition and complexity, resulting in software that improves individual productivity while failing to address the interdependency of mining functions. For this reason, technology vendors like Gemcom are following partnership approaches with their clients, engaging corporate and operational stakeholders to better understand mining business objectives. This presentation examines some of the approaches that help foster the development of solutions that leverage the information produced during mine operations to improve downstream process control and tactical decision support.

May 1, 2006

By Michael J. Magyar

The Federal Bureau of Mines has developed a hydrametallurgical method to recover aluminum, aluminum oxide, and fluxing salts from aluminum salt slags. The slag is leached with water at room temperature to produce a saturated brine slurry. Screening of the slurry yields an aluminum-rich fraction that can be returned to the dross furnace. The remaining slurry is vacuum filtered, yielding a clear brine solution and an aluminum oxide filter cake. Evaporation of the clear filtrate produces a high-purity fluxing salt for reuse in the dross furnace. Over 80 pct of the metallic aluminum is recovered in the aluminum-rich oversize fraction, while essentially all the fluxing salts are recovered by evaporation. This report contains the final results of an investigation on a process research unit scale, an economic evaluation of the method, and recommendations to further improve the process.

Jan 1, 1979

By David R. Skuse, Jacek A. Kostuch, Steven M. Fortier

"Particulate ground calcium carbonate (GCC) is used as a filler and coating pigment in a wide range of applications including papers, paints, plastics and films. In this paper we will overview the requirements for GCC used in both filling and coating applications in the paper industry and highlight the processes used in the production of these materials.INTRODUCTIONCalcium carbonate is both abundant and very widely distributed occurring most commonly as limestone, marble and chalk (Harben 2002). Given, the high purity, whiteness and relative inertness of these materials it is not surprising that they are heavily utilised in a range of industrial applications. Worldwide ground calcium carbonate (GCC) capacity is estimated at 50.5 million tonnes per year (Roskill, 2002). This usage is divided between relatively coarse materials that are used in applications such as landscaping, cultured marble and carpet backing and finer grades that find application in plastics, rubbers, inks, paints and paper. Given the usage of calcium carbonate products across a very wide range of consumer products, the outlook for GCC is very promising with growth expected in many markets. Growth is anticipated across many applications in the emerging nations and more specifically in paper applications on a global basis.Over the last several decades the GCC processing industry has evolved to be well adapted to both the cost effective production and delivery of standard products and the production of high performance speciality products. Many of the standard unit operations found in the metaliferous raw material processing industry are also used, albeit in some cases in modified form, in the processing of GCC. Coarse products (diameter > 3 - 10 µm) are typically produced by dry processing routes. Whereas, the finer products are typically produced by a combination of wet and dry processing."

Jan 1, 2004

By Ronald J. Mathis

The objective of this contract is to design, build, surface test, and evaluate a breadboard prototype of the Variable Wall Mining System so that data are available for the design of a production machine. The Variable Wall Mining System (VWMS) consists of a series of side cutting augers, connected end to end, and distributed across a panel. Supplying rotary power at the end of the string and anchorage from conventional longwall roof supports, the augers are sequentially thrust into the face and then lifted to the roof to extract the coal in a continuous manner. The augers not only cut but also transport the coal. The effort described in this report summarizes the operation characteristics of the VWMS, the design methodology used to develop various working models, the surface testing of a ½ -scale version of the VWMS, prediction of power requirements and performance potential of a full-scale system, and a critique of the VWMS concept, conclusions, and recommendations.

Jan 1, 1987

By Dale Lens, W. S. (Wayne) Cusitar

"The use of continuous loading and conveying technology for mining is currently practiced in relatively few mining environments and, even in these cases, on a non-exclusive basis. For the most part, and particularly in hard rock mining, appropriate equipment technology has only recently been developed for continuous loaders, mobile low profile crushers and flexible face conveyors. Mining R&D work by Inco Limited has promoted the development and proving of a loader suited to hard rock conditions and capable of sustained loading rates of500 tonnes per hour. Current R&D work at Inco will test the production capabilities of a low profile mobile crusher by CMS/Eagle and a flexible/ mobile face conveyor system by DME. This follows successful production testing of the Belt Bender concepts in potash mining in Saskatchewan and the development of enhanced extensible conveyor equipment features by DME. Numerous applications are seen for variations of the LCC technology in soft rock, hard rock and surface mining environments. Introduction In some respects, this paper is an announcement of new technology which has the potential to bring revolutionary change to the mining industry. It is also the story of technology transfer, in which mining concepts that have developed independently in underground soft rock and hard rock mines and in surface mining operations are being brought together for a common benefit. It is also the story of key developments in equipment technology which 'complete the cycle' of cooperating technical capabilities to enable the revolution to begin. The phrase ""technological revolution"" requires some defmition: an equipment innovation, or invention, or improvement, will only be revolutionary if its use gives rise to a significant new mining practice."

Jan 1, 1987

By C. E. Van Orstrand

An intrusive body is a mass of igneous rock that has migrated upward, presumably from great depths. Great variations in form, composition and depth of burial occur. It is not proposed in this paper to go into all of the details of the problem. Instead, it mill be assumed here that the intrusive has the form and characteristics represented in Fig. I. According to W. 11. Emmons minerals are not deposited in appreciable quantities below the "dead line." Important amounts of ores of virtually all metals may be found around summit cupolas, but only gold, copper and zinc (in limited quantities) are usually associated with trough cupolas. Most students of ore deposits agree that temperature changes are largely instrumental in precipitating many ores in the "hood" and that the difference in temperature between the intrusive and that of the country rock may be the chief factor in determining the mineralogy of a deposit. A problem then of some interest is to correlate the principal physical features of the intrusive with the phenomena of heat conduction as evidenced by the cooling curves and the isothermal surfaces. Mathematical Theory In order to show the possible application of heat conduction to the interpretation of the processes of metalliferous deposition associated with intrusives, it will be as- sumed that the intrusive is a large par-allelopiped of dimensions, 2l, 2m, 2n. The equation that represents the flow of heat from the parallelopiped into country rock (v = o, 1 = o), which has the same thermal properties as the intrusive, is2,3 l-x v I FT 2 [2 2 — l-x m — y — m — y n — z In this equation, the origin, x = o, y = o, z = o, is at the center of the parallelopiped. v = temperature at point x, y, z, time 1. v, = initial temperature throughout the intrusive, 1 = o. k = coefficient of thermal diffusivity. a, ß, y are variables of integration. Put n = m in Eq. I, and we have v I [2/5 [2I-x 2 — l-x m — y 2 2 2 kt 2 20xt e-a2da ebrdß

Jan 1, 1946