Search Documents

By M. E. Alam

In the present study, 1.1 volume percent of nano size copper was incorporated into pure tin using hybrid microwave sintering assisted powder metallurgy route. Microwave sintered samples were extruded both at room temperature and at 230 °C. Microstructural characterization studies were conducted on the extruded samples to investigate the distribution characteristics of secondary phase and grain morphology. Room temperature tensile test results revealed that hot extruded Sn-Cu samples exhibited higher strengths (~ 41%, in case of 0.2% yield strength and ~ 38%, in case of ultimate tensile strength) and ductility (~ 15%) when compared to room temperature extruded samples. On the contrary, the tensile properties of pure tin remained independent of extrusion temperature. An attempt is made in this study to correlate the effect of extrusion temperature on the microstructural evolution and tensile properties of Sn-Cu solder.

Jan 1, 2009

By Frank A. Peters

The Bayer process treating Jamaican bauxite was evaluated from an economic standpoint, using standard estimating methods and published data, to present a reference point for cost estimates for nonbauxite alumina processes. The estimated operating cost for a plant producing 1,000 tons of alumina a day is $47.96 per ton of alumina when charging $8 per ton for bauxite and $2.30 per hour for direct labor. The estimated fixed capital cost is $46 million.

Jan 1, 1966

This NIOSH Toolbox Training program contains 52 different modules designed to stimulate safety discussions among your employees. Each module is intended to be completed in roughly 10 or 15 minutes, so a Toolbox Training session can be conducted once a week for the entire year. Each session counts toward your employee’s 8-hour annual MSHA refresher training, thus saving an entire day of work.. The modules are used to refresh employees on the procedures, policies, and practices of working safely at a specific mine site and can easily be tailored to fit conditions and situations found on your property. Every module follows the same format, so that as the weeks pass, miners will start to approach every safety situation in the same way. A typical Toolbox Training session contains five basic steps that cover all the information in the module. 1. Identification of the hazard and discussions about the types of injuries typically associated with the hazard. 2. Discussions of some of the causes of the hazard. The MSHA example included with each module should be referenced. 3. After the hazard and accident has been explained and understood, discussions about best practices and tips for avoiding a similar accident. 4. Review of similar conditions or near misses from your mine site using the leading questions on the form to start a discussion. Specific examples of equipment or structures on the site that could lead to the same accident should be discussed. The blank space on the module is used to add your own remarks and questions to supplement the given information. 5. Miners fill out the training record on the back of the form with name, initials, and date of training session. The modules are designed to be kept in a standard three-ring binder and easily photocopied. This way, the same set of modules can be used for years to come. A blank form is included that can be used to create more Toolbox Training modules. The key component of Toolbox Training is to start a discussion among employees that will allow them to see the hazards around them every day and respond to these hazards in a safe and consistent manner. To start a discussion, ask questions that need more than a one-word response. Get the miners to talk about similar situations from their own experiences and give suggestions about how to fix the hazards around them. Toolbox Training is a quick and effective way to cover specific mining hazards, but it only works if miners are involved in the discussion.

Jan 1, 2004

Previous models describing the aggregation of polymer coated particles fail to take into account the fact that there are a limited number of sites onto which a polymer segment can adsorb, called ?active? sites. Thus, the collision efficiency is a factor not only of the fractional surface coverage, but also of the number of active sites. In this study, a physical model of the flocculation system was devised in which the number of these sites could be varied, in order to study the effect on particle aggregation.

Jan 1, 1987

By R. L. Guerguerian

Nowadays, most grinding mills driven by a wrap-around ring motor are operating successfully. Some of the earlier problems could be attributed to the lateral stiffness and stability of their bearings. As a result, modifications to the bearings included the rearrangement of the shoes, or the addition of more shoes, closer to the horizontal centerline. This technical paper reports a study of the effects of bearings on the lateral stiffness of grinding mills driven by a wrap-around ring motor. The discussions cover the design of the four shoe trunnion bearings and examine the effects of the angular location of the shoes.

Jan 1, 2000

By Rüdiger Wunsch

The new high speed Vienna - St.Pölten line and the Lainzer tunnel are to be connected to the existing Western railway line in Vienna. This involves building an underground cut and cover branching tunnel which will be connected to the Western railway line by ramps. A key structure is the Herzmansky Street tunnel, which has a length of some 820m. It is to be constructed as a cut and cover tunnel using the top down method. The walls of the tunnel are designed as a water resistant structure consisting of double walls, an outer wall of bored piles and an inner reinforced concrete wall. The bored pile wall will be used as a temporary retaining wall during the construction phase and will also be a structural part of the per­manent tunnel wall. The retaining walls of the open pit, which will have a depth of up to 14m and a width of 12m, were investigated as a non-contiguous bored pile wall and overlapped bored pile wall. Preventing ground water from penetrating into the pit is of paramount importance. The high ground wa­ter level is the determining factor for the dimensioning of the bored pile wall and results in the require­ment for a water resistant concrete structure. It has been necessary to adopt adequate measures, therefore, in order to reduce the hydrostatic water pressure during the construction phase, assuming economical pile dimensions.

Jan 1, 2000

By H. F. Fuls

The quality of Pregnant Leach Solution (PLS) at Skorpion Zinc is of utmost importance for efficient operation of the Solvent Extraction (SX) Plant. Suspended solids in the PLS forms CRUD in the settlers, resulting in reduced zinc transfer capacity and increased impurity carry over to Electrowinning. The Ishigaki Fibre-Wakishimizu filter (fibre media rapid filtration equipment) has been identified as polishing filter that potentially could remove solids from the PLS of Skorpion Zinc. A pilot unit with 20m³/h capacity was tested on site over a period of 9 months under plant operating conditions in the refinery. The FW filter produces a clear filtrate, acceptable for the Solvent Extraction. Turbidity is improved by 72%. Gravimetric analysis indicates a 47% removal of solids. However, the gravimetric method is biased by a co-precipitation of saturated salts during the analysis. Filter media is blinded by the Skorpion Zinc PLS solution, as result of suspended solids and process chemistry. The media could not be regenerated to acceptable conditions. Further testwork to investigate the impact of process solution chemistry modification on blinding is undertaken. Based on the outcome of this investigation a final decision on the FW filter can be taken.

Jan 1, 2008

By Ralph H. Espach

In the spring of 1943, when it was evident that the Tensleep sandstone in the Elk Basin field, Wyoming and Montana, held a large reserve of petroleum, Bureau of Mines engineers obtained samples of oil from the bottom of nine wells and analyzed them for such physical characteristics as the volumes of gas in solution, saturation pressures or bubble points, shrinkage in volume caused by the release of gas from solution, expansion of the oil with decrease in pressure, and other related properties. The composition of the gas in solution in the oil was studied. The pressures and temperatures existing in the reservoir and the productivity characteristics of the oil wells were determined. The data obtained indicate that the oil in the Tensleep reservoir of the Elk Basin field has unusually varying physical characteristics, such as a saturation pressure of 1,250 pounds per square inch absolute and 490 cubic feet of gas in solution in a barrel of oil at the crest of the structure, and a saturation pressure of 530 pounds per square inch absolute and 134 cubic feet of gas in solution in a barrel of oil low on the flanks. The hydrogen sulfide content of the 6a r; in solution in the oil varies from 18 percent for oil on the crest to 5 percent for oil low on the flanks of the structure. Of even greater significance is the fact that these and other variable characteristics of the reservoir oil are related to the position of oil in the structure. Many geologists and petroleum engineers have considered all the oil in a petroleum reservoir to have uniform physical characteristics and that equilibrium conditions prevailed in all underground accumulations of oil and gas. That such is not always so is borne out by the results of the study made by the writers.

Jan 1, 1951

Paper presented at the IAGOD international symposium on mineralization related to mafic and ultramafic rocks held in Orleans, France, 1-3 September 1993. Phases of the Ir sub-group are present either as inclusions in or interstitially to chromite and are unaffected by (or only altered in situ during) hydrothermal processes. By contrast, almost all phases of the Pd sub-group are located in a secondary textural setting - in fractures in chromite or between fragments of brecciated chromite. The different settings indicate that the mineralisation episodes were associated with magmatic and hydrothermal stages respectively. The presence of an included Pd-group mineral in a hydrothermally Pd-group mineralised chromitite sample suggests that the hydrothermal Pd-group minerals were at least partly derived by remobilisation from magmatic deposits in the chromitite pod. These observations indicate that Pd-group elements are more mobile than Ir-group elements under hydrothermal conditions and point to the potential for hydrothermal platinum and palladium mineralisation in favourable environments

Apr 1, 1994

By C. J. Farrow, M. J. Smith

"Bechtel has managed a number of test programs to establish autogenous grinding circuits and size mills for a variety of ores.This paper outlines the procedures whereby bench scale and pilot plant tests are used to select the most efficient circuit to grind the range of ore types likely in the mill feed.Five examples are given. One example traces the development of a pilot plant program; it shows how bench scale Work Indices provide a target for the grinding power requirement of an ore and relates how pilot circuits are changed as a result of interpreting the results from preceding tests. The other four examples relate the interpretation of the test results to provide design data; they illustrate a number of phenomena which have been observed.INTRODUCTIONConventional crushing and grinding circuits can be specified from bench scale test data such as Bond Work Indices. Bond Indices have been correlated to a large number of rod and ball mills and by applying appropriate factors, mills can be sized from the Work Index.For autogenous or semi-autogenous grinding circuits, bench scale tests are not sufficient to be able to specify the circuit and size of the mills for a commercial plant. It is necessary to run a series of pilot plant tests to determine how the ore behaves."

Jan 1, 1982

Existing processes for the recovery of platinum group metals (PGM) from UG-2 ores place stringent requirements with regard to chromite content upon feed material to the plant. An alternative hydrometallurgical process for which this is not an issue is proposed that involves reductive roasting of the ore followed by leaching with HCl/chlorine, ion exchange, and recovery of PGM from the ion exchange eluate by reduction. Problems associated with leaching of PGM are discussed and results of laboratory testwork for each of the process steps are given.

Jan 1, 2004

By F. R. Hensel

P. R. Kalischer.*—I should like to amplify a little one of the points made by Dr. Hensel, and rather violently disagree with him at the same time. He brought out the point that when the higher forming pressures are used on the green compacts there is a marked decrease in the density as sintered. We found that to be true and, of course, many of you notice that that is true with copper compacts also. But, in my opinion at least, it is not true that the expansion is due to entrapped air. We have vacuum-pressed both silver and copper compacts and obtained almost exactly the same numerical expansion as we secured by pressing in air. The powder, however, that is vacuum-annealed does show a slight decrease in expansion on sintering, but almost the entire increase on expansion can be overcome by very slow rates of heating. And it is our opinion that a majority of the expansion is due to dissolved oxygen in the discrete metal particles themselves rather than to entrapped gases. Another interesting observation that we have made is that often with silver or copper compacts it is desirable to silver solder or braze the compact into some part of a piece of equipment after completing powder metallurgical operations on it. If such a compact is sintered and coined, say a silver compact, given an initial forming pressure of 10 to 15 tons per square inch, and sintered, there is an adequate amount of shrinkage and it can be coined at about 50 or 60 tons per square inch and bring up the density nearly to theoretical. If, then, that compact is silver-soldered into some part of a fixture or a machine, it will expand very beautifully, and the only way that this can be overcome. as far as we know, has been to reanneal after the coining operation at a temperature higher than is to be used in any subsequent operation. In that way, a density very nearly theoretical can be achieved, but the coining operation cannot be carried to the excessively high pressures or expansion and bubbling of the compact will occur again.

Jan 1, 1945

By F. C. Gennari, D. M. Pasquevich

With the gradual exhaustion of natural rutile, there has been extensive research into its synthesising from lower-grade titanium minerals. The removal of Fe from pseudobrookite (Fe2TiO5) by chlorination was studied, using both isothermal and non-isothermal thermogravimetric measurements. Correlation of the results obtained from element distribution maps, scanning electron microscopy, energy-dispersive X-ray analysis and phases detected by X-ray diffraction in the chlorinated samples showed clearly two associated processes. First, the pseudobrookite particles reacted with chlorine and iron was removed selectively as FeCl3(g), leaving a solid residue rich in the TiO2 phases anatile and rutile, separated from an inner layer of unreacted pseudobrookite by a distinct interphase boundary. Second, chlorine allowed TiCl4(g) to form in the reaction bed, where it removed iron from the Fe2O3 crystals as FeCl3(g) and substituted Ti through a pseudomorphic reaction

Jun 21, 1905

Polyacrylamide flocculating agent has been used in the Leaching Division 'of the Risdon Works of the Electrolytic Zinc Company of Australasia Limited since October, 1960. The number of thickeners in the continuous thickening stage was thereby reduced from eight to three. There has been an increase of 25 per cent in throughput and a reduction of solids in thickener over-flow from 3-4 g/l. solids to 0·5 g Ir. solids. Reagent addition has been at the rate of 0·25 lb Separan NP10 per ton solids.Additionally there has been a gain of 3 per cent in current efficiency as the direct result of the addition of Separan NP10 to purified cadmium sulphate solution priOl; to electrolysis for cadmium metal. A smoother deposit has resulted and it has been possible to increase deposition time between strippings from 47 to 71 hr. However, there has been a slight increase in the lead content of the cadmium metal produced.The use of Separan NP10 to settle copper bearing residue in a batch process stage has resulted in a five-fold increase in settlement rate and a reduction in purification cycle time.INTRODUCTIONThe Electrolytic Zinc Company of Australasia Limited, Risdon, Tasmania, produces zinc by electrolysis of purified zinc sulphate solution, the raw material being zinc sulphide concentrate. In the Risdon process (Van Arsdale, 1953; J ohnstone, 1953; Ross, 1949) the compound zinc ferrite (ZnO.Fe203) is formed during the concentrate roasting stage. When the roasted material is leached in dilute sulphuric acid the zinc ferrite is not attacked, and it remains as part of the insoluble leach residue, of which it may form as much as two-thirds of the whole. The remainder is mainly unroasted zinc sulphide, unleached zinc oxide, lead sulphate, gypsum, silver compounds etc. The zinc in the residue may be 10 per cent of that in the original concentrate.Continuous thickeners are used to recover the valuable residue from the impure zinc sulphate solution and the...

Jan 1, 1963

By Carl Lubbe, Ron Frye, Wayne Curtis, Julie Pecori, Dan Leach

Blasting conducted in the USA using the new Electronic Initiation System developed by Altech has shown that an accurate delay system will benefit the customer. Results from test work clearly showed that improved fragmentation was effected and blast vibration was at least similar to that currently found at the test venue with improvements possible.

Jan 1, 1997

Sluice box operating practices in Papua New Guinea (PNG), and published work on sluice boxes are briefly reviewed. Some recent work on sediment entrainment mechanisms occurring in sluice boxes have also been described. In the light of this information, some drawbacks in the commonly adopted sluice box operating practices in PNG, and ways of overcoming them, are also highlighted.

Jan 1, 1991

By Robb L. Swenson

Construction of foundations for the Skyway Segment of the San Francisco Oakland Bay Bridge required innovative techniques due to the mass of the structures being inserted and the unique subsurface of the Bay. Twenty of the pier structures required large sheet pile cofferdams. Eight other foundations were installed in open water without cofferdams at the deeper part of the Bay. This narrative will present the initial planning, as well as the stages of installation, for each type of foundation. The first section will discuss foundation constructability modifications made during the initial planning phases of the project. Considerable effort was expended by Caltrans, the owner, T.Y. Lin the designer, and KFM (Kiewit/FCI/Manson) the contractor in modifying the design to assure that required tolerance would be maintained during the installation of the foundations. The final section will describe the steps required for installation including: initial access dredging, installation of cofferdams, preparation required to install the footing boxes, footing box installation, foundation support pile installation, and pile to box connections.

Jan 1, 2013

By R. Armstrong

The stability of rock slopes is significantly influenced by their curvature in plan view. The importance of this in open pit mining is indicated by the fact that, in a deep pit, steepening of the slopes by 1° may save as much as $100 million. It is considered that there are two significant factors that play a part in the influence of plan curvature. These two factors are the effect of stress, and the effect of geological structure. The scant literature that pertains to this aspect of rock slope design was reviewed. The geometrical influence of the plan curvature was then investigated. It was seen that it has a parabolic effect on the maximum possible wedge that can fail into a circular pit, where the tighter the concave curvature the smaller the wedge. The plan curvature also affects the volume of a particular wedge, where concave slopes result in an exponential decrease in the volumes and convex slopes have exponentially increased wedge volumes. A change in the strike of the wedge did not affect the curvature’s influence on the volume, but the volumes of shallower dipping wedges were affected more by the influence of the plan curvature. La stabilité des talus des roches est très influence par la courbure de celles ci dans la vue en plan.Son importance de l peut arriver à sauver même $100 millions. Il est considère qu il y a deux facteurs importants qui jouent une influence sur cette courbure. Il s’agit de l’effet des contraintes et l’effet de la structure géologique. La brève littérature qui se réfère à cet aspect du conception sur le talus des roches a été revue. L’influence géométrique de la courbure des plans a été investiguée. Il a été vu que cela un effet parabolique sur la bosse ou le su relèvement maximum possible qui peut faillir dans un puits circulaire, ou le plus resserre est la courbure concave, le plus petit est su relèvement (bosse). La courbure plane aussi affecte le volume d’un particulier su relèvement ou les talus concaves résultent dans une décroissance exponentielle en volume alors que les talus convexes accroissent la volume de ces su relèvements (bosse). Le changement de l’orientation de la bosse (su relèvement) perpendiculairement ou obliquement n’ a par affecte l’influence de al courbure sur le volume mais les volumes des bosse (su relèvement) peu profonds étaient affectes par la courbure des plans. Die Stabilität der Felsensteigungen wird erheblich durch ihre Biegung im Plan beeinflußt. Der Wert von diesem in der Tagebaugrube wird durch die diese Tatsache, in einer tiefen Grube, steepening der Steigungen durch 1° angezeigt; kann soviel wie $100 Million speichern. Es wird betrachtet, daß es zwei bedeutende Faktoren gibt, die eine Rolle im Einfluß der Planbiegung spielen. Diese zwei Faktoren sind der Effekt des Druckes und der Effekt der geologischen Struktur. Die dürftige Literatur, die diesen Aspekt des Felsensteigungdesigns betrifft, wurde wiederholt. Der geometrische Einfluß der Planbiegung wurde dann nachgeforscht. Es wurde gesehen, daß es einen Parabolischen Effekt auf dem maximalen möglichen Keil hat, der in eine kreisförmige Grube ausfallen kann, wo, das fester die konkave Biegung, das kleiner der Keil. Die Planbiegung beeinflußt auch das Volumen eines bestimmten Keils, in dem konkave Steigungen eine exponentiale Abnahme an den Volumen ergeben und konvexe Steigungen exponential Keilvolumen erhöht haben. Eine Änderung im Schlag des Keils beeinflußte nicht den Einfluß der Biegung auf das Volumen, aber den Volu

Jan 1, 2003

The Tasman Orogenic Zone is regarded as a single metallogenic province (the Tasman Province) with four SUb-provinces corresponding with its major tectonic components: the Lachlan, New England, Hodgkinson.and North Queensland orogenic provinces. Within the Tasman Province there are four main ore-rock associations.These are1. manganese and iron with sedimentary and basic volcanic rocks,2. zinc-lead-copper and copper with intermediate-acid volcanic sequences,3. minor chromium, platinum, and osmiridium with ultramafic complexes, and4. tin, wolfram, gold, and copper with syn- and posttectonic granitic intrusions.Whereas the ores of ultramafic and volcanic associations form geographically-restricted metallogenic districts, the ubiquitous granitic ores may be subdivided into twenty-one districts that cover almost the entireOrogenic Zone. The Tasman Province is notably lacking in uranium ores and Mississippi Valley-type deposits.There is a distinct tendency for ores of each association to be progressively younger to the east and north, thus paralleling the progressive growth and stabilization of the Zone. Similar ore-rock associations are present in repeated phases of mineralization from the Cambrian to the Permian-Triassic, reflecting the essential homogeneity of the Tasman Province, and the similarity of the successive tectonic cycles.

Jan 1, 1972

By A Jewbali, J Phillips, C Boyle

Normal practice in the mining industry is the creation of a single geological model. These models provide a single interpretation of the geological and mineralisation domains. These interpretations infer the exact behaviour of ore domain contacts at shorter scales when resource definition drilling is done on wider scales and are thus locally highly uncertain. The interpreted geological model provides a single number for the volume and tonnes of mineralised material enclosed by the mineralisation envelope. It is on this single number for volume and tonnage that capital intensive mine development decisions (mine design and scheduling, stockpile strategy, waste management, closure planning, dewatering strategy, product quality, etc) are based. Some of these decisions require knowledge of grade variability for small volumes of material such as quarterly production periods. It is generally recognised that this information cannot be derived from single kriged geological models, but can potentially be modelled by conditional simulation techniques. Uncertainty in the extent and continuity of the mineralised envelope and its effect on grade variability for shorter production periods is thus recognised as a major source of uncertainty in new mine development.CITATION:Jewbali, A, Boyle, C and Phillips, J, 2013. Quantifying domain uncertainty for an iron ore deposit, in Proceedings Iron Ore 2013 , pp 157-168 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013