Search Documents

By P. W. Lotz

Traditionally, bottle roll tests have been used to optimize the extraction process for best gold extraction and recovery. Such tests typically involve exposing the ore to defined reagent concentrations (lime, cyanide and sufficient oxygen) and balance the gold input with recoveries and losses. With mounting pressures to accommodate sustainability issues during development work, it became apparent that much more information would be required on the interactions and kinetic behaviour of solid and solution species during the entire leach process. This information is vital to enable proactive management of critical issues such as cyanide, arsenic, water and tailings management. Inadequate management of these aspects has led to temporary closures and, in cases of non-compliance, to the dynamically changing regulations. MINTEK?s advanced leach facility (ALF) is being developed with the aim of bridging the knowledge gap between the gold leach process and the predictable environmental impacts upon discharge. The facility aims to monitor all parameters of relevance such as pH, Eh, dissolved oxygen, metals, cyanide species, and viscosity during the entire process to enable more informed decisions on practical interventions. The presented set of data reflects first experiences gained from processing a refractory gold ore concentrate. Attempts at optimizing the process were limited due to the developmental nature of the work. Data relating to leaches with differing preoxidation conditions and cyanide staging is presented.

Jan 1, 2009

By J Graaf, R A. Murrell

Gold Fields Australia is constructing two major ventilation shafts at the Wallaby gold mine in Western Australia. The new ventilation shafts are required to facilitate the long term ventilation strategy for the mine, thereby allowing continued extraction of ore beyond 1000 m below the surface. The construction work has involved all of the challenges that shaft construction can throw up, including challenging geotechnical conditions, unexpected high water inflows and major circulation loss during pilot hole drilling for raise boring. An extensive geotechnical and hydrological investigation program was undertaken prior to awarding the shaft construction contracts. While most of the risks were identified, several proved to be much more challenging than expected. The shaft construction methods included conventional sinking into the fresh rock profile in each shaft, followed by raise bore pilot hole drilling and reaming. A headframe was constructed for the first shaft, which was sunk to 92 m with a stage suspended in the shaft to facilitate the concrete lining and provide rope guides for the kibble winding. Drawing from experience when sinking the first shaft, additional ground pre-conditioning was implemented for the second shaft, which was pre-supported with continuous piles to 28 m followed by sinking to 50 m using a crane instead of winders and a headframe. Following the conventional sinking through the weathered zone in each shaft, the shafts were completed using a raise bore. The first shaft utilised a riser pipe and rotary vertical drilling system (RVDS) with the second shaft having utilised a dual rotary rig for pilot hole drilling. This paper reviews the site investigations undertaken, construction methodologies applied, the results achieved and the lessons learnt.CITATION:Murrell, R A and Graaf, J, 2017. Shaft construction at the Gold Fields Wallaby mine, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 321–334 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By John Watson, Tom Treleaven

This guide presents nur-nerous patterns that provide 8 millisecond separations between initiated charges. The guide is tabulated in seven sections to provide Quick reference by number of decks or bunch blasting. The pattern IS presented in the section where the highe!$ number of decks works. It should be noted that patterns applicable to multipledackshwtings are alsoapplicsblefor fewer decks.

Jan 1, 1995

By J. Donovan Jacobs

Many improvements in the art of underground excavation have appeared during the past two decades. These improvements have been both in methods and in machinery and have resulted in more economical construction of today's tunnels. In the realm of machines, the developments of continuous boring heads for either soft ground or rock, random arm excavators and the sliding tunnel floor (Magic Carpet) have each made contributions toward more rapid tunneling. CONTINUITY OF ADVANCE Tunnel boring machines are often referred to as "continuous excavators". Continuous advance (without cyclical interruptions) has not been achieved, however, in any of the machines now in use. In most rotary-head tunnelers the thrust needed to make the cutters bite into the face is obtained from hydraulic cylinders reacting against anchoring devices held stationary by pads which grip against the sides of the tunnel. With this system the forward motion of the cutting head is continuous only until the propelling cylinders have reached their limit of extension. At this point the grippers must be released, moved forward and reset before a new cycle of advance can be begun. Some machines are built to obtain their propelling thrust from hydraulic cylinders pushing backward against newly-installed rings of tunnel support. This is the customary method for propulsion of shields. With it, each cyclical advance or "shove" must await the erection of a new ring of supports. Faster tunnel driving

Jan 1, 1974

By D. C. Kaliampakos, A. K. Moutsatsou, J. K. Skotaras

The wastes from marble extraction in the Thasos- Kavalla-Drama region of northeastern Greece could be utilised as a new source of high-quality white carbonate fillers for the European market. Large deposits, satisfactory properties, acceptable processing costs and environmental benefits are among the factors that would have a positive bearing on a proposal for their use in this way. DTH, the waste arising from dolomitic marble quarrying operations on the island of Thasos, appears to be the more suitable material than DA waste from Nikissiani on the mainland because of the lower cost of primary grinding and the higher production rate of ultrafines with a mean particle size of 5 micrometres (the optimum size for filler properties in the case of both DTH and DA), its superior whiteness, the benefits that such use would bring to a very severe and complex environmental problem and the lower transport cost

Jun 18, 1905

By E. B. Johnson

Cleveland-Cliffs lron Co., which operates Marquette lron Mining Co.'s Republic mine, conducted a test whereby 35,000 tons of self-fluxed pellets were produced in the grate-kiln system from specular hematite flotation concentrates. A brief description of the pelletizing plant is presented along with pertinent operating details. Date is included which compare operating conditions and the chemical and physical properties of the green and fired pellets for the self-fluxing pelletizing test with the normal acid pelletizing operation. The success of self-fluxed sinter in enhancing the operation of the blast furnace during the past few years has reasonably led to the assumption that the use of self-fluxed pellets might result in even greater furnace efficiencies. A great share of development work in agglomeration has been directed towards techniques related to the production of self-fluxed pellets, but only a limited tonnage of self-fluxed pellets had been produced on a commercial scale until this past year when The Cleveland-Cliffs Iron Co. produced 35,000 tons of such pellets by the grate kiln system at the Republic mine during the period May 21-June 5, 1962. REPUBLIC'S GRATE-KILN PLANT The grate-kiln pelletizing process consists of four stages, namely: feed or balling circuit, traveling grate, rotary kiln and annular cooler (Fig. 1). The balling section is conventional and utilizes four 9x30-ft balling drums in closed circuit with 5x14-ft vibrating screens having 3/8-in. rod decks. The traveling grate is 12 ft wide by 126 ft long and has 14 windboxes — six in the drying section and eight in the preheat section. The rotary kiln is 15 ft ID shell and 114 ft long. The annular cooler is 40 ft in diameter and has 12 windboxes. The cooler is divided into two zones by a moveable curtain wall. The high temperature air from the first zone is used as secondary combustion air in the kiln. Normally the only heat supplied is through the burning of No. 6 oil in the single kiln burner. Hot gases pass counter to the pellet flow through the system. The exit gases from the kiln pass down draft through the preheat section through cyclones and are drawn through the drying bed prior to exiting via the stack. The temperatures are normally held within the following ranges: Kiln 2400-2445 °F Preheat 1850-1950°F Drying 480-520°F Exit gas 200°F Pellets 120°F The design capacity of the Republic mine grate-kiln system was 2500 Itpd. Sustained production in excess of 35% over design capacity has been achieved. No screening of the cooler product is practiced. PELLETIZING TEST CONDITIONS When a decision was made to proceed with a test at the Republic mine pelletizing plant to produce 35,000 tons of self-fluxed pellets, several potential failure factors had to be carefully considered. Research work on a batch and pilot plant scale indicated that the grate-kiln system at Republic would require some major changes in order to obtain optimum conditions. In many cases compromises were agreed upon as major equipment changes and revisions were not feasible. The pelletizing conditions which laboratory development tests revealed were required in order to insure successful production of self-fluxed pellets were: 1) Good mixing of limestone and concentrate and proper moisture control; 2) Higher gas flow rates in the preheat section than are normally used; 3) Higher preheat temperatures than normal; 4) Maximum kiln temperature 2350°F. There was just cause for concern about balling problems that might occur. Approximately 10% of dry pulverized limestone was to be added to the specular hematite concentrate just ahead of the Pekay mixers on the belt feeding the balling drum. Large scale

Jan 1, 1963

By S Hu, P Ni, H Xu, P Chen

Indosinian (T) orogeny amalgamated the Mongolia-Xingan fold zone, the North China continent, the Yangtzi platform and the SE China fold zone into a unified continent. The early to middle Yanshanian (J-K1) orogeny created a Cordilleran type active continental margin in East Asia, reactivated the consolidated East China continent, and generated a large amount of granitoids, calc-alkaline volcanics and W, Sn, Mo, Cu, Au, and U ore deposits. The late Yanshanian (K2) orogeny began a transition to the western Pacific type continental margin. A tensional environment led to the development of peralkaline magmatism and tne formation of continental basins with red beds. The Himalayan (Tr-Q) orogeny was characterised by a backarc spreading and rifting regime. The dominant magmatism was continental basaltic.

Jan 1, 1995

By G. Belzil, F. Robichaud, M. Fullam

"The Goldex mining and milling complex is operated by Agnico-Eagle Mines Ltd. and is located in the Abitibi greenstone belt of Northwest Quebec, Canada. The mill operates presently at a throughput of 8,250 tpd with gold grade varying between 1.8 and 2.2 g/t. The ore is very high in gravity recoverable gold (GRG) at about 92% and as such a significant emphasis was placed on the gravity circuit. Commercial production started in 2008. Average gold recovery is 93.5% with about 68% of gold recovery coming from the gravity circuit. Over the course of the first several years of production, several gravity audits were carried out. In 2009, a complete gravity audit was completed, including ore, classification, Knelson Concentrators, and the gold room. In 2011, an audit was undertaken of the flotation circuit to determine the efficiency by which GRG is floated. Large samples of flotation feed and tails were collected and process for GRG content. This allowed a link between gravity and overall recovery to be made. This paper presents results of the audits and the development of a model linking gravity and overall gold"

Jan 1, 2012

By W. E. Dennis, M. M. Fine

"INTRODUCTION During peacetime, the United States uses less than 3,000 tons of chemical-grade celestite annually. The war need, however, was estimated to exceed 15,000 tons a year.Hitherto; most of the required chemical-grade ore has been imported from England, Mexico, and other foreign countries. If foreign sources do not find it possible to meet the demand for ore of chemical grade (plus 92 percent SrSO4), it is expected that requirements could be satisfied by concentrating low-grade domestic ores. Celestite deposits on Brown, Nolan, Fisher, and Coke Counties, Texas, are considered to be possible sources of supply for this low-grade material. The Bureau of Mines explored the most important deposits to determine the grade and amount of ore available and conducted ore-dressing tests to obtain a suitable method of concentration.The exploratory work, consisting of test pitting and sampling, was carried on under the direction of W. E. Dennis, one of the authors of this paper, from October 8, 1942, to January 30, 1943. The ore dressing-tests described herein were conducted at the Bureau of Mines Laboratory at Rolla Mo.In this report, a particular deposit is referred to by the name of the landowner on whose .property the .deposit lies. The location of the deposits investigated is shown on figures 1, 2, 3, and 4.The celestite deposits were previously studied by the Bureau of Economic Geology of the University of Texas, and the results of its investigation are published in Mineral Survey Circular No. 46."

Feb 1, 1947

By S. Mendenhall

The Golden Sunlight Mine (GSM) began operation in 1982 with a strong commitment to environmental stewardship and the local community. This commitment ensured the long-term physical, chemical and ecological stability of the mine site and maintained an active partnership with local stakeholders. Concerns for economic development intensified as mine closure loomed on the horizon and fostered the inception of the Community Transition Advisory Committee(CTAC).This coalition of interested area stakeholders has the primary focus to sustain current mining operations while concurrently seeking alternative post-mine economic development opportunities utilizing existing mine assets. Accomplishments include development of an Asset Re-utilization and Post-closure Plan, a community survey regarding the impending mine closure, recruiting an international wind energy company to develop a wind farm, and development of an industrial/business park. The synergy of this strong partnership is key to meeting sustainability goals and enhancing potential future mining operations. The cooperative effort of the GSM and the local stakeholders is a success story that could be a role model for other mining operations.

Jan 1, 2004

In the course of the last twenty eight years the copper lodes of New Caledonia have been periodically worked or abandoned, until quite recently, probably attracted by the higher price of the metal, British capital has again been induced to embark upon the further development of several copper properties, which at present give reasonable promise of becoming regular producers. Owing to its proximity to Australia (only a three day's journey by mail steamer from Sydney) New Caledonia becomes of additional interest to Australian commerce in general, and it is to be hoped that the French Government may see their way before long to make the best of this natural position, to the mutual benefit of both countries concerned.Op till now all copper ores and concentrates which have been shipped from New Caledonia, were treated in Australian smelting works furthermore, Australian mine managers and miners have from time to time been connected with New Caledonian mining ventures, but, unfortunately, it must be said that nearly everyone of them returned to Australia thoroughly disgusted with his experience over there. Even to the casual observer, it is not so very difficult to find a proper explanation for these shortcomings in the peculiar economic conditions of the 'French colony, as many of the objections which have hitherto existed in connection with mining operations, were the direct consequences of a system of colonisation which could not possibly have been productive of better results.

Jan 1, 1901

By C. R. Edwards, J. R. Smith

"INTRODUCTIONThe purpose of this paper is to give an overview of the ALSANDS PROJECT, with emphasis on the approach taken in the design of the Primary Extraction and Froth Treatment Plants.The Alsands Consortium (Table 1) is a Joint Venture of 9 companies formed in 1978, with its prime objective to obtain governmental approval and concomitant suitable commercial terms to build and operate a third oil sands mining and upgrading facility in the Athabasca Oil Sands Deposit.Alsands Energy Limited is the Consortium Manager.The Alsands Project will provide about 10 percent of Canada's forecast crude oil production by 1990, which will be 20,700 cubic metres per day (130,000 barrels/day) of synthetic crude oil plus 1,100 cubic metres per day (7,000 barrels/day) of liquid petroleum gases. To construct Alsands the time required by construction labour, field non-manual and engineering support personnel as well as those trades involved in project-related urban development will total approximately 100,000,000 manhours or 50,000 man years. During regular operations, 4,800 people will be employed by Alsands.Approximately $13 billion will be spent to design, construct and start up the plant by the scheduled 1988 completion date."

Jan 1, 1982

A predicted increase in aluminium production and the possibility of a diminishing supply of petroleum coke for anode electrodes in alumina reduction cells makes it desirable to find alternative electrode materials. Browncoal char, with a lower ash content and with an elemental purity similar to petroleum coke, was produced by leaching in hydrochloric acid, washing with water, and charring at 1,150°C. The cost of processing is estimated tobe competitive with petroleum coke.Without further processing the bulk density and real density were undesirably low, but by briquetting the coal before charring and crushing, the bulk density was improved to 92 per cent of the petroleum coke value andthe particle density was improved to 92 per cent of the density of petroleum coke by water displacement or 75 per cent by mercury displacement.Pre-baked electrodes were prepared from the char alone, mixtures of petroleum coke and char, and from petroleum coke alone, all bonded with coal tar pitch.The electrodes were tested for the usual physical properties and were evaluated for performance in a laboratory size alumina reduction cell.Electrodes based on brown coal char alone were found to be inferior in physical properties and performance, but mixtures of the char and petroleum coke, despite poorer density, electrical resistivity, and carbon consumptionon a theoretical basis, in performance tests gave up to 17 per cent better carbon consumption per weight of aluminium produced and 21 per cent better electrical current efficiency than the electrodes based on petroleum,coke alone.It is suggested that larger scale tests are warranted.

Jan 1, 1971

By Grigor Mishev, Georgi Petrov, Benjamin Cebrian

Before designing a single blast or all the blasts on a pit level, it is critical to assess the main goal on each. To do this, a series of constraints must be taken into account: wall protection, vibration control, flyrock hazards, fragmentation required, desired displacement as well as economy, equipment efficiency. The tool to do this is the Blast Master Plan. Many mines fail to integrate on its elaboration key stakeholders such as planning, operations, geology/geotechnical and milling departments. Designs not only have to provide consistent behavior of the blasts, but have to make sense all in one with the geological and geotechnical conditions as a starting point. Once blasts are designed under an organized set of priorities, and complemented with quality controls, optimization is possible on a large scale.

Jan 1, 2016

By Lewis Martin

Spokane Research Center personnel are currently conducting research on cable bolts to assess their material and support properties, to provide design criteria for roof control systems under various types of underground mining conditions, and to provide background data for computer models of cable bolt supports. Laboratory studies of cable bolts made of conventional steel cables with Garford bulbs and collars resulted in recommendations on characteristics such as embedment length, hole diameter, cable bolt diameter, and configuration of cables. A completed series of laboratory tests has determined the minimum embedment length of resin required for resin-grouted, cable bolt ground support.

Jan 1, 1996

Wastewaters from Mining Projects both gold mining and coal mining generally have minerals in solution or very fine material which does not settle out quickly. These waters in the past have been discharged into the nearest water course and caused extensive pollution.

Jan 1, 1986

By Dave Stefanuto

Voisey?s Bay Project Components ? Mine/Mill Port In Labrador ? Mini Plant in Mississauga ? Demonstration Plant in Argentia ? Supply Vessel (Umiak1) ? Transshipment Facility (Quebec) ? Concentrate Handling & Transport to Sudbury/Thompson ? Cobalt Refinery Upgrade (Thompson) Project Setting ? The Project is on the traditional lands of the Labrador Inuit and the Labrador Innu ? Canadian courts have held that Aboriginal peoples in Canada possess special rights to traditional Aboriginal lands Those rights can include requiring resource developers to enter into Impacts and Benefits Agreements (IBAs) on traditional lands to set forth how lands can be used and benefits to be received by Aboriginal people

May 1, 2006

By J Hall, A Gallardo, M Strizek

Mineralogy and coproponents Sino Iron, International Minerals and Austeel are in the process of developing four world class magnetite iron ore mines with multiple open pits along a 25 km strike length of Brockman Iron Formation to the south of Cape Preston on the West Pilbara coast. The close proximity of the proposed pits raises some challenging project approvals and environmental management issues relating to the impacts of dewatering at individual projects and the cumulative impacts of progressive development on local and regional groundwater resources, which includes a large fresh water aquifer system in the Fortescue River alluvium.This paper presents an outline of the hydro-environmental impact assessment process adopted and the key result that the cumulative impacts of dewatering at all four projects on the local brackish groundwater system in the basement rocks is only marginally more than the impact of any one project on its own, and that the impact on the Fortescue River alluvium aquifer is negligible. The paper also presents an outline of the proposed integrated water management approach that will involve coordinated monitoring, ongoing impact assessment and management, and reporting programs for all projects.

Jan 1, 2009

By T. O. Hagan

A simulated rockburst experiment was conducted underground at a deep level gold mine. This was done by means of a large explosion detonated in solid rock close to a tunnel sidewall. The resultant shake-out damage is typical of that associated with a small seismic event in close proximity to a tunnel that is subjected to the estimated field stress, as in this case, of 50 MPa. The experiment involved: ?the design of a blast to mimic a seismic source ?seismic monitoring using a dense seismic array ?high speed video filming ?a study of rock mass conditions (fractures, joints, rock strength etc.) before and after the simulation using mapping and ground penetrating radar ?special investigations to evaluate the mechanism and the magnitude of the damage ?a study of support behaviour under excessive dynamic loading.

Jan 1, 2001

By S. S. Makgato

In this study, coke oven tar additions over a range of 0?8 wt.% were evaluated as a possible substitute for imported coal fractions. The coke oven tar used was collected from tar decanters in the byproducts section of the coking plant. The moisture content in the tar varied depending on the residence time and water carryover from the coke oven tar separators to the storage tanks. Moisture contents of 1 wt.%, 3 wt.%, and 6 wt.% were investigated in order to evaluate the effect on coal blend, carbonization, and coke properties. At 6 wt.% moisture content with 6 wt.% coke oven tar, although the coke quality improved the yield showed a 4% decrease. On the other hand, 1 wt.% moisture content with coke oven tar of 6 wt.%, increased the yield by 1% and the coke quality improved. However, the latter process was characterized by an excessive increase in wall pressure and pushing energy, both of which are detrimental to the oven walls. The optimum moisture content in coke oven tar was found to be 3 wt.% with a coke oven tar addition of 6 wt.% in the coal blend. With these conditions, the coke properties improved and wall pressure and pushing energy were acceptable. However, a decrease in coke yield of up to 2% was observed. Despite this, coke oven tar addition is considered to be a viable option based upon economic factors of a reduction in the quantity and cost of imported coking coals that is required to achieve the same optimum final coke product. Keywords coal substitution, coke oven tar, tar moisture, coal blend, coke, coke quality.

Nov 1, 2013