Search Documents

By Joseph T. Coe, Siavash Mahvelati, Philip Asabere

Characterization of existing foundations remains an important issue as foundation reuse and rehabilitation continue to garner increased attention. In the case of unknown foundations, geophysical and nondestructive testing (NDT) methods have been utilized in the past to evaluate foundation geometry and could serve as useful tools in the case of foundation reuse. A comprehensive study was initiated in the late 1990’s and early 2000’s that evaluated the effectiveness of the available geophysical and NDT technologies to characterize unknown foundations for scour evaluation purposes. At the time of that study, the Multichannel Analysis of Surface Waves (MASW) geophysical method was in its infancy and not widely used. Since then, MASW has become increasingly prevalent in geotechnical applications as the method presents a number of potential advantages when characterizing the subsurface, including rapid testing, increased signal to noise ratio, and ability to resolve velocity inversions. This paper presents a case study that explores the abilities of MASW as an unknown foundation characterization tool. MASW was applied to determine subsurface stiffness at a bridge foundation site in the Philadelphia metropolitan area. One MASW survey line was performed immediately over the foundation of interest and another was performed over a control zone adjacent to the foundation to establish a baseline site profile. The purpose of this testing was to examine whether MASW could establish the geometry of the foundation at this site. This paper presents the site conditions and MASW testing procedures, followed by a discussion of data analysis and interpretation.

Jan 1, 2016

By Arthur F. Johnson

Plant sites for the light metal industry must be located where ample low cost power is available. In the first half of the century hydroelectric development was the only source of this power-now the best sites have been exploited and those remaining do not promise enough water to permit year-round capacity power plant operation. In searching for economic plant sites engineers have concentrated on locations with vast water power potential. Olin Mathieson Chemical Corp. has been studying the economics of developing water power to make aluminum. However natural gas, lignite, and even atomic energy have also been considered as possible power sources for aluminum production. Economic studies have given consideration not merely to investment and production costs, but to total costs of delivering fabricated products to the market center of the U. S. When delivered costs are considered and when full account is taken of the newest techniques of mining bituminous coal and utilizing it to make electric power, one arrives at the inescapable conclusion that coal has emerged as the economic answer to American aluminum production.

Jan 4, 1955

By Víctor Barrientos

"El presente texto es un estudio realizado para seleccionar la alternativa de menor costo global a largo plazo para el reemplazo de un cargador frontal en arriendo y que tiene 32.000 horas de operación. Para ellos se seleccionaron 3 alternativas de 5 -en tanto el equipo que seguirá operando en faena, será uno de igual marca y modelo y se contempla un equipo de otra marca, pero de capacidad y performance equivalente. Asimismo, para la evaluación se utilizó el criterio del costo anual equivalente (CAE) que sirve para decidir entre proyectos alternativos y con vidas útiles distintas. Sin embargo, la limitación está en la escasez de información en costos de operación y mantenimiento (O&M), desconocimiento del impacto de las prácticas operaciones, condiciones climáticas en las vidas útiles de los componentes de mayor valor y las condiciones de mercados de equipos mineros en arriendo."

Jun 1, 2016

By Jorge Morales

El presente trabajo señala las definiciones sobre la gestión de activos, requerimientos básicos, aplicación práctica y un modelo mediante un mapa de ruta para una industria minera de gran escala. En ese sentido, el reto de este mapa estriba en ser un modelo organizacional donde uno identifique lo que hace bien y las brechas de oportunidad, defina los procesos para lograr los objetivos y así ensamblar esos procesos comprobando la coherencia y el alineamiento con la estructura, estrategia y cultura organizacional. Finalmente busca desarrollar las soluciones, el plan y la toma de acciones y así aprender de las consecuencias.

Jun 1, 2015

By M Freeman

In a visionary move, the Planning Commission and the Ministry for Planning in Western Australia decided to invite three extractive industry quarry operators, local government councils and State Government departments (Minerals and Energy, Environmental Protection, South West Development Commission) to contribute jointly to study the impacts of blasting on areas surrounding basalt quarries in the Bunbury region of WA. The results of the study will help establish suitable zones in which land uses will be controlled under a proposed Greater Bunbury Region Scheme and in local planning schemes, to minimise conflicting land uses. This paper discusses the blasting program conducted to characterise and model the vibration behaviour of the rock under the effects of pilot-scale and full production blasting, and highlights some of the benefits achievable when a thorough blasting impact program and assessment is conducted at the planning stages of land-use establishment.

Jan 1, 2001

By G M. Volkmann

Pipe umbrella systems have effectively been used as an additional support system in the working area in weak ground conditions during the last decades. Thus, a considerable number of applications accounts in urban tunnelling with shallow overburden. However, this support system is also successfully used when a tunnel alignment crosses fault zones, sediments, moraines or talus with overburdens from shallow to deep. The pipe umbrella support system itself is termed differently worldwide – synonyms are canopy tube umbrella method, umbrella arch method, or long fore-poling method.One main reason for the increase in application is that this support system closes cost-effectively the gap between reasonable, normal supported tunnels and tunnels supported with more expensive special techniques like horizontal jet-grouting or ground freezing. By using this system, many projects can be built more cost effective without decreasing the common level of safety.The pipe umbrella construction method is pretty young, so the knowledge about this system has been intensely researched in the last decade. This led to an enormous increase in understanding the interaction between support system and surrounding ground, the mode of action, and the important details for construction.Pipe umbrella support systems are applied in difficult ground conditions, so a special developed measurement arrangement was used to observe deformations ahead of the working face during tunnelling. The evaluation of collected data sets identifi ed that cased-drilling systems have clear advantages compared to predrilling systems during the installation process in weak ground conditions. This may become important depending on project requirements, so this difference must be considered in design as well as in the tender document specifications.

Mar 8, 2011

By F. Pinto, C. A. Prato, R. J. Rocca, P. F. J. Huerta Soaje

"The seismic hazard for civil engineering structures is generally defined in terms of deterministic or probabilistic acceleration response spectra at an equivalent rock outcropping. The design of tunnels, however, requires the definition of demands in terms of accelerations at ground surface (near the portals) and in terms of both accelerations and velocities at different depths within the alignment. The design near the portals is controlled by inertial effects and is often times impacted by the possibility of slope instability and rockfall, whereas the design at deep sections is controlled by kinematic effects. These effects are accounted for in practice by introducing deformation patterns in the structure that are related to an assumed wavefield, often times ignoring the effect of the structural stiffness in the response. This paper presents a study regarding the definition of seismic demands for different sections of 14-km long tunnel in the Andes (Argentina-Chile), with a maximum overburden of 1750 m in a seismically active region. The tunnel will pass through volcanic massifs mainly composed by andesites and rhyolites.The study includes the definition of spectrum-compatible seismograms, deconvolution, and definition of accelerations and peak particle velocities for different overburden conditions. A kinematic interaction study for a 500-m tall ventilation chimney shaft is also described, where a simple formulation for the interaction analysis is considered in order to more accurately evaluate shear and bending demands. INTRODUCTIONThe seismic design of linear underground structures, such as shafts and tunnels, generally considers the inertial forces near the shallow sectors (e.g., portals) and the kinematically imposed deformations for the deep sections (e.g., Hashash et al. 2001). The inertial forces are often times evaluated on the basis of design spectra recommended by seismic hazard studies. The kinematic demands for the deeper sections, however, needs to be defined in terms of additional information which is not always indicated by the seismic hazard studies, e.g.; peak particle velocities and accelerations, and their variation with depth. These parameters can be determined by means of a site response analysis, whereby outcrop motions can be deconvoluted in order to evaluate motions inside the ground mass (e.g., Schnabel et al., 1972). Hashash et al. (2001) defines factors that may be used in order to account for attenuation of motions inside the ground mass. However, these factors are provided for depths up to 30 m only, whereas depths of tunnels structures can range up to thousands of meters."

Jan 1, 2015

A combination of the needs of business, employee desires and safety and health considerations is stimulating increasing attention to the time spent by people at work and the timing of that work. Particularly we are seeing: - innovative work schedules for 24-hour mining businesses; and - response from industry to accommodate the needs, even the desires, of employees in return for systems which are more productive and more capital efficient. There appears to be an evolutionary trend for business management to become more sophisticated and responsive to the need for achieving close to best cost work schedules to sustain continuous improvement. The underlying motivating forces driving this trend for improved techniques in organising attendance at, and time spent at work, is the seemingly inseparable combination of technological advance and ever-increasing accumulation of capital. The mining industry has not remained untouched by this thrust for ever-increasing need for best use of labour, to adopt advances in technology and to provide attractive opportunities for putting accumulated capital to work. An essential component of this on-going thrust is a substantial effort by the mining industry to improve the performance of labour by providing most-productive work schedules.

Jan 1, 1996

By W. D. Bryson

This paper is one of a series being prepared by the United States Bureau of Mines on tunnel-driving methods. The practices described are those used at No. 11 mine of the Colony Coal Co., Denver, Colo. No. 11 Mine is situated at Dines, some 14 miles north of Rook Springs, in Sweetwater County, Wyo. It is served by a spur off the Winton branch of the Union Pacific Railroad. The Colony Coal Co.'s mines were opened in 1918, and since that time have been among the largest producers of coal for the railroad and domestic markets in the Rock Springs coal district.

Jan 1, 1932

By Steven Hoerger

Mixed integer linear programming (MILP) production scheduling models can be used to evaluate if tonnage improvement projects will deliver value over all time periods and whether new bottlenecks will be created. These MILP models can evaluate the interconnected effects of mine and process capacities, mining locations, cutoff grades, stockpiles, and orebody grade/tonnage distributions. A case study compares potential value creation from a mine capacity increase, a mill capacity increase, or a simultaneous increase in all capacities. For perspective, project valuations for capacity increases are compared against valuations for cost reduction projects, mine planning improvements such as phase design, dynamic cutoff grades and stockpiling, and the impact of geostatistics improvements in the areas of block model accuracy and ore control selectivity.

Feb 1, 2024

By P Velletri, N Gaylard

The management of wear surfaces in mining operations has remained largely unchanged since the inception of mining. Sacrificial wear liners are installed on the inside of chutes, hoppers and other equipment used to transfer bulk ore to protect the asset from abrasive wear caused by the flow of material. These liners are generally replaced at fixed intervals which may be determined based on historical wear rates or may be driven by other maintenance requirements for that asset. This approach does not always yield satisfactory results, especially for critical assets where the impact of downtime on production can be substantial. For such assets, a condition-based maintenance strategy has the potential to significantly increase productivity and reduce the total cost of ownership associated with the asset. However, for such a strategy to be successful, timely information on the actual condition (remaining thickness) of the wear liners is essential. This paper describes the development and implementation of a wear monitoring system that can be used to remotely and continuously report on remaining liner material thickness in real time. It details some of the challenges that were overcome when developing the system, including the design of a patented thickness measuring system that can be used in a variety of liner materials and is tolerant to the presence of ore on the wear surface. The paper also explains how a cloud-based approach enables data from the wear sensors to be integrated into external systems such as a data historian, which has been demonstrated through a collaborative project with one of the largest iron ore producers in the Pilbara. This ability to combine real time liner thickness information with other data sources, such as throughput, provides the foundation for the transition to a condition-based maintenance strategy.

Nov 8, 2021

By S. Ford

The introduction of recent advances in molecular biology into the field of microbial ecology has made available a powerful set of analytical tools for dissecting the structure of microbial communities in natural environments. The use of these approaches, many of them based on DNA-DNA hybridization enables the researcher to assess the occurrence of specific DNA sequences among the natural bacterial flora (Ford and Olson 1987). These techniques promise to have wide application as tools for monitoring the spread of introduced microorganisms (Trevors, 198'): Ford and Olson. 1987) and have been used to examine the response of bacterial communities to environmental contaminants and stressors (Barkay and Olson. 1986. Olson and Ford. 1986. Olson. Ford and Lester 1987) The occurrence of heavy metal resistance among microorganisms has been discussed as a possible tool for the detection of pathfinder elements employed in mineral exploration (Olson and Barkay 1986). In addition, the occurrence of heavy metal resistant bacteria may be utilized in protocols for assessing the occurrence and biological impact of contamination occurring as a consequence of mining operations. In this context the use of DNA hybridization technology enables the investigator to directly quantify the number of heavy metal resistant bacteria by the use of genetic probes specific for those resistance genes. The implementation of a strategy for detection of heavy metal resistance genes by hybridization technology is dependent on the availability of data on the genetic systems which encode resistance The availability of extensive DNA sequence data on mercury resistance genes (Brown et a11986. Barrineau et al 1984) has lead us to use gene probes specific for mercury resistance within natural bacterial populations as a model system for investigating the response of these bacterial populations to the occurrence of mercury In the environment.

Jan 1, 1988

To improve the level of hearing protection by providing workers with an inexpensive, easy-to-use device to check earplug fit. Background Approximately 30 million workers are exposed to hazardous noise on the job, placing them at risk of permanent hearing loss, tinnitus, and other disorders. Although the preferred solution is to eliminate noise through engineering controls or to reduce noise exposure through administrative controls, hearing protectors are critical when noise is unavoidable. Studies of hearing protector users have shown that average protection values in the real world are much lower than the labeled noise reduction ratings determined in laboratories with trained and motivated subjects. Even worse, many hearing pro­tector users get virtually no protection at all because of poor fit. The studies also show that users have a harder time achieving adequate protection levels with earplugs than with earmuffs. It?s difficult for users to tell if earplugs are working well just by looking at them. A more accurate approach is to check how much they block or ?attenuate? noise. Earplugs vary in their attenuation characteristics, with most providing a maximum of 20?35 decibels of noise reduction when worn correctly. Any earplug that?s suitable for use in noisy settings will attenuate noise by at least 15 decibels. Personal fit testing is an effective way to help hearing protector users improve the fit and protection levels of the devices. However, existing fit-testing systems are expensive and unsuitable for use at many industrial worksites.

Dec 1, 2008

[Abbott, Jay Union Supply Co., 7458 So. Jackson St., Denver, Colo. 80122 Achziger, Ronald H Midwest Rubber & Supply Co., 6404 E. 39th Ave., Denver, Colo. 80207 Acre, Lee Dorchester-Colomine, 2944 Hwy 6 and 24, Grand Junction, Colo. 81501 Adams, Robert W Energy Fuels Corp., 3 Park Central, Suite 900, Denver, Colo. 80202 Adams, Dell H Consolidation Coal Co., Consol Plaza, 1800 Washington Rd., Pittsburgh, Pa. 15241 Adams, Douglas K General Electric Company, P.O. Box 2331, Denver, Colo. 80201 Adams, E. E Armco Steel Corp., Box 53, Parker, Colo. 80134 Ahlborg, William Joy Mfg. Co., 26 Sedgwick Dr., Englewood, Colo. 80110 Albrecht, Wayne H North American Coal Corp., Kirkwood Office Tower, Bismarck, N.D. 58501 Albrechtsen, Ray H. Mountain States Resources Corp., 1399 So. 700 East, Suite 11, Salt Lake City, Utah 84105 Alke, R. J Westinghouse Elec. Corp., 55 West 5th Ave., Denver, Colo. 80204 Allen, Thomas S Construction Machinery, Inc., 6121 Clermont, Commerce City, Colo. 80022 Allison, Thomas W Gullick Dobson International, 603 Parkway View Dr., Pittsburgh, Pa. 15205 Allmendinger, James W Falkirk Mining Co., P.O. Box 731, Riverdale, N.D. 58565 Almarez, John Jeffrey Mfg. Div., Dresser Industries, 720 So. Colorado Blvd., Denver, Colo.80222 Althouse, John G Coteau Properties Co., 2400 Astronaut Dr., Bismarck, N.D. 58501 Amundson, Adolph L. Western Slope Carbon, University Club Bldg., Suite 2240, Salt Lake City, Utah 84111 Anderson, Andy Power Motive Corp., 5000 Vasquez Blvd., Denver, Colo. 80216 Anderson, Carl L Industrial Screen & Maint., Inc., 1680 Sherrelwood Dr., Denver, Colo. 80221 Anderson, Charles W. R. Stamler Corp., 600 Main Street, Millersburg, Ky. 40348 Anderson, Daven Energy Engineering, Inc., P.O. Box 33, River Forest, Ill. 60305 Anderson, Forrest S Anderson Mavor (U.S.A.) Ltd., 303 Progress St., Cranberry Ind. Park, Zelienople, Pa. 16063]

Jan 1, 1979

By R. Stanford

In any discussion of steel pouring too often refractories quality assumes a high level of importance. Unfortunately when one considers the many and varied conditions to which pouring refractories are exposed, it is difficult to isolate the true role of refractories quality alone. Some of the more important, yet often overlooked, variable conditions bearing on pouring performance are heat size, tap time and temperature, steel chemistry, ladle additions, ladle height and preheat, mechanical conditions of the pouring mechanism, hot top or non hot topped ingots and, ingot size, which determine total number of shutoffs, direct or tundish pouring, ingot filling rates, metallurgical demands, etc, etc. These considerations apply for either conventional or slide gate pouring of ingots and, to a large extent, even strand casting. In any event probably the most significant factor on pouring performance in any individual shop is what is considered an "OK" pour. We find considerable variance in this qualification, not only between Republic Steel meltshops, but throughout the industry. Therefore, it is a worthless exercise to draw comparisons attributable to refractories quality alone, except for similar conditions in a single shop.

Jan 1, 1972

By A. L. Slaughter

The Homestake mine, located in western South Dakota, was discovered in 1876. The first reported production was in I 878. Total production through 1965 is 6,554,249 troy ounces of silver and 27,961,276 troy ounces of gold, worth $987,000,000 at present prices. Precambrian sedimentary formations at Lead total 20,000 feet. The Poorman Formation, the oldest, is chiefly ankerite carbonate. The Homestake Formation is iron-magnesium carbonate. The younger formations are argillaceous with some quartzites. The Cambrian Deadwood Formation unconformably overlies the Precambrian. All are cut by Tertiary intrusives. Sideroplesite schist of the Homestake Formation was converted to cummingtonite schist in the zones of higher-grade metamorphism. The Precambrian rocks show the effects of extreme isoclinal folding. A second stage of folding ( cross folds) may have been caused by the Tertiary intrusives. All folds plunge to the southeast. The Homestake ore bodies are pipe-like replacements of the Homestake Formation in zones of cross folding. It is believed that dilatation of the schists has increased permeability in these zones. Chloritization of the schists is the most widespread effect of the mineralization which is divided into four stages. Principal minerals of the first stage are quartz, chlorite, and arsenopyrite; in the second stage, quartz, ankerite, and pyrrhotite. In the third stage only pyrrhotite was deposited. The fourth stage followed the intrusions of Tertiary dikes and deposited mostly pyrite and calcite. Gold accompanies all stages and is always the last mineral to be deposited. It is most closely associated with arsenopyrite of the first stage but can be interpreted as having been deposited during the fourth stage and superimposed on the products of the earlier stages.

Jan 1, 1968

By Kevin Phelan, Gary Johnson, Peter Sperring

The vast majority of tailings in the Western Australian Goldfields are deposited in purpose-built storage facilities. At mine-sites with open-pit mining operations there is also the requirement to mine and stack large volumes of waste rock, usually into surface waste dumps. As these dumps have typically 30% of their gross volume present as voids, there is the potential to use this void space for the storage of tailings. The concept of co-disposal is to store the tailings material in the void space of the waste dumps, eliminating the need for a separate tailings storage facility. Dominion Mining Limited have been investigating the possibility of using co-disposal as a means of tailings storage. Laboratory testwork has been used to understand some of the issues associated with the concept, and assist in the design of an on-site demonstration of the concept. Co-disposal offers a number of potential advantages, and despite a number of practical hurdles to overcome, considerable economic and environmental benefits could be realised if this concept can be demonstrated on a commercial scale. The major advantage of such a system is to remove the need to build, operate and rehabilitate a separate tailings storage facility. Rehabilitation can be incremental throughout the mine life as the co-disposal site will be virtually indistinguishable from a current waste dump in both size and form. Other potential advantages include more stable waste dumps, less land area disturbed on the project site, and better water recovery from the tailings.

Jan 1, 1995

Scientific drilling and blasting techniques are currently being presented to the mining industry as an aid in the overall optimisation process. The degree of success in the development of these techniques over the last ten years has prompted statements that generally relate to blasting becoming a science rather than an art. Many of the techniques are currently operated or at least analysed by scientists. As such, their use has been restricted to project type activities while the more routine activities associated with day to day mining has continued to be carried out by engineering rather than scientific staff. Some of the scientific techniques will remain legitimately as a project or an occasional use facility. Generally speaking a cost/benefit analysis at a particular mine will decide the level of use. This should logically highlight a number of techniques with potential of regular mine site use. Regular mine site use implies mine site analysis and hence the gulf between the scientist and mine operator/engineer must be addressed. There are all sorts of solutions and they are not mutually exclusive. One alternative could be to increase specialisation at the mines. With "career paths" becoming more formalised the trend would seem to be away from mine site specialists unless, for instance, this specialisation was provided by term secondment from research establishments. Another alternative could be the scientists themselves applying their developmental skills to "humanise" and "package" the projects in such a manner that they can be routinely used at mines.

Jan 1, 1990

By N. C. Gay, P. J. Van Der Veever

The Klerksdorp gold mining district, South Africa, experiences a relatively high level of seismicity with many seismic events of magnitude greater than 4. These large events appear to have foci close to fault planes, most of which displace the strata by several hundred metres over a wide area. To help understand the mechanism of these large mining- associated seismic events, in situ stress measurements were made at 4 sites using "CSIR doorstopper" strain relief techniques. The sites were chosen close to, or some distance from fault planes and other structures. The results show that at all 4 sites a relatively large horizontal stress is oriented approximately north- west. The magnitude of this stress ranges from 0,78-1,O of the vertical stress. A marked horizontal stress anisotropy, varying from 13-30 MPa is also present. The dominant structural features are large, north-east striking normal faults which extend across the entire length of the goldfield. Displacements across these faults vary from a few centimetres to several hundred metres. Bedding plane faults across which large displacements may occur are also common as are north and north-west striking dykes. The majority of the faults strike at approximately 90º to the maximum horizontal stress and at all sites a large compressive stress plunges in the direction of dip of the strata and fault planes. Thus a significant shear stress may act across suitably oriented planes causing them to be in a state of potentially unstable equilibrium. This abnormal stress situation would exist along the entire length of the fault

Jan 1, 1982

By Eric K. Albert, J. Kiusalaas

The paper presents an overview of SPASID (Kiusalaas and Albert, 1983), a new computer program developed under U.S. Bureau of Mines funding for the prediction of surface subsidence caused by under- ground mining operations. The presentation, which is illustrated with two case studies, also re-evaluates the influence function method as a tool of subsidence prediction, arriving at some rather unconventional recommendations. SPASID consists of four modules that communicate through common data bases: (1) Preprocessor. This module prepares and maintains the database for the entire site. The database contains all the information about the site and the mine operation that is necessary for the computation of subsidence. (2) Subsidence Predictor. The influence function method is used to predict the surface displacements that occur in any portion of the site that occur between two given dates. The computations take into account the time lag between extraction and displacement, and the effects of pitching seams and incomplete compaction at the edges of panels. The program contains i not he's influence function and the Green's function of transversely isotropic elasticity theory. (3) System Identification. The purpose of System Identification is to determine the optimal values of the various parameters associated with the influence functions in the Subsidence Module. System Identification requires measurements of subsidence from a site with a sirnilar overburden structure. The values of the subsidence parameters are obtained by minimizing the discrepancy between the measured and computed surface displacements. (4) Postprocessor. The Postprocessor is a graphics facility for displaying the data generated by the other program modules.

Jan 1, 1984